Installation guide

QuadroM32x/8L/26x/12Li/26xi Manual II: Administrator's Guide Administrator’s Menus
QuadroM32x/8L/26x/12Li/26xi; (SW Version 5.3.x)
112
CAS Signaling Wizard – Page 4 appears only in E1 User
mode when signaling selected from Signaling Type drop
down list on the CAS Signaling Wizard – Page 2 is R2 (all
types) and is used to configure country settin
gs. Page
consists of the following components:
Country drop down list is used to set the location where
Quadro is located to support the correct functionality of R2
signaling. For countries absent in this list, use ITU selection.
Use Default Country Settings checkbox restores default
advanced settings for the selected country. When this
checkbox is not selected, next page will provide a possibility
to manually configure advanced country settings.
Fig. II-196: CAS Signaling Wizard – Page 4
CAS Signaling Wizard – Page 5 appears only in E1 User mode when signaling selected from Signaling Type drop down list on the CAS Signaling
Wizard – Page 2 is R2 (all types) and when Use Default Country Settings checkbox is not selected on the previous page. This page is used to
configure advanced country settings. Page consists of the following components:
ANI Category drop down list appears only when R2 signaling selected from Signaling Type drop down list on the CAS Signaling Wizard - Page 2
is different from R2 DTMF is used to select the calling party priority depending on the call originator’s location specifics.
ANI Request Transmit and ANI Request Receive drop down lists allow you to select the Caller ID request R2 tones for transmit and receive.
Seize Acknowledge Timeout
text field is used to define a
timeout (in a range from 2 to 2000 milliseconds) between
incoming seize signal and the corresponding feedback.
Answer Guard Timeout text field is used to define a wait
timeout (in a range from 0 to 1000 milliseconds) Group-B
Answer Signal and Line Answer.
Release Guard Timeout text field is used to define an idle
timeout (in a range from 0 to 120000 milliseconds) between
the disconnect signal receipt and call disconnection.
Dialing Delay Timeout text field is used to define a timeout
(in a range from 0 to 2000 milliseconds) before injecting
dialed digits. Timeout specially refers to R2 DTMF signaling.
Incoming DNIS Size
text field indicates the number of
received digits (in a range from 0 to 255) required to establish
a call. When field has 0 value, system uses either timeout
defined in the Incoming digits timeout field or the End of
Address messages to establish a call. Independent on the
value in this field, the message End of Address always
causes the call establishment.
Unused A:B:C:D text fields require to configure unused C
and D bits of E1/T1 CAS signaling (A and B bits are
predefined). Fields may have either 0 or 1 values.
Invert A:B:C:D text fields are used to invert the ABCD status
bits in time-slot 16 before TX and after RX. If bit is set to 1,
the router inverts it before transmission and after the receipt.
End of DNIS (I-15) checkbox is used to enable End of DNIS
service.
Collect Call checkbox is only available when Brazil is
selected in the Country drop down list on the previous page
of the wizard and when the PBX attached to the Quadro
supports this feature. When this checkbox is selected and in
case of incoming calls, always the called destination will pay
for the call. Option is particularly applicable when calling from
the mobile phone. Checkbox should be selected when the
appropriate feature is enabled on the PBX.
Fig. II-197: CAS Signaling Wizard – Page 5
The Allow Timeslot Blocking checkbox indicates whether the system should use blocked timeslots to make outgoing PSTN calls. If this checkbox
is selected, the system will NOT use timeslots blocked by the carrier. If the checkbox is clear, the system will try to unblock the timeslots and will
make outgoing calls if succeeded.