VS220/VS320/VS325W User's Guide
Contents VS220/VS320/VS325W User's Guide.......................................................................................................... 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents.....................................................
Connecting to an S-Video Video Source................................................................................... Connecting to a Video Source for Sound .................................................................................. Connecting to External USB Devices ............................................................................................ USB Device Projection..............................................................................................................
Available Color Modes................................................................................................................... Turning On Auto Iris....................................................................................................................... Controlling the Volume with the Volume Buttons................................................................................ Projecting a Slide Show ....................................................................................
Cleaning the Air Filter and Vents............................................................................................... 92 Replacing the Air Filter.............................................................................................................. 92 Projector Lamp Maintenance......................................................................................................... 94 Replacing the Lamp ........................................................................................
Projector Dimension Specifications.................................................................................................. Projector Electrical Specifications .................................................................................................... Projector Environmental Specifications............................................................................................ Projector Safety and Approvals Specifications..................................................................
VS220/VS320/VS325W User's Guide Welcome to the VS220/VS320/VS325W User's Guide.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Related concepts Projector Part Locations Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To receive an S-Video signal, you need an S-Video cable compatible with your device. See your local computer or electronics dealer for purchase information. • To receive a component video signal, you need a D-sub, 15-pin, component-to-VGA video cable. You can purchase one from Epson or an authorized Epson reseller. • To receive an HDMI signal, you need a compatible HDMI cable.
Option or part Part number Accolade Duet portable projector screen ELPSC80 ES1000 Ultra Portable Tabletop Projection screen V12H002S4Y ES3000 Ultra Portable Tabletop Projection screen V12H002S3Y Universal projector ceiling mount ELPMBPJF Adjustable suspended ceiling channel kit ELPMBP01 False ceiling plate kit ELPMBP02 Structural Round ceiling plate ELPMBP03 Adjustable Extension Column (pipe) 8" - 11" (20 to 28 cm) ELPMBC01 Component-to-VGA video cable (ELPKC19) V12H005C19 VGA video cabl
Notations Used in the Documentation Follow the guidelines in these notations as you read your documentation: • Warnings must be followed carefully to avoid bodily injury. • Cautions must be observed to avoid damage to your equipment. • Notes contain important information about your projector. • Tips contain additional projection information.
Projector Parts - Front/Top 1 Exhaust vent 2 Lamp cover 3 Horizontal keystone slider (VS320/VS325W) 4 Control panel 5 Projector status lights 6 Focus ring (VS220) 7 Speaker 8 Air filter cover 9 Intake vent 10 Zoom ring (VS320/VS325W) 15
11 Focus ring 12 Remote receiver 13 Lens cover (VS220) or A/V Mute slide (VS320/VS325W) 14 Front adjustable foot 15 Foot release lever 16 Lens cover lever (VS220) or A/V Mute slide lever (VS320/VS325W) Parent topic: Projector Part Locations Projector Parts - Rear 1 Remote control receiver 2 Audio ports 3 S-Video port 4 USB TypeA/document camera port 5 USB TypeB port 6 Computer port 7 HDMI port 16
8 Lamp cover screw 9 Kensington security lock slot 10 Video port 11 AC input port Parent topic: Projector Part Locations Projector Parts - Base 1 Mounting bracket holes 17
2 Front adjustable foot 3 Rear feet 4 Security cable attachment point Parent topic: Projector Part Locations Projector Parts - Control Panel VS220 1 Power button 2 Source Search button (searches for connected sources) 3 Menu button (accesses projector menu system) 4 Enter button (selects options) 5 Wide/Tele buttons (adjust projected image size), horizontal keystone adjustment buttons (adjust screen shape), and arrow buttons 6 Vertical keystone adjustment buttons (adjust screen shape) and
8 Help button (accesses projector help information) VS320/VS325W 1 Power button 2 Source Search button (searches for connected sources) 3 Menu button (accesses projector menu system) 4 Enter button (selects options) 5 Volume control buttons, horizontal keystone adjustment buttons (adjust screen shape), and arrow buttons 6 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 7 Esc button (cancels/exits functions) 8 Help button (accesses projector help information) P
Projector Parts - Remote Control 1 Power button 20
2 Computer button (cycles through connected computer sources) 3 Video button (cycles through connected video sources) 4 Numeric buttons (enter numbers) 5 Auto button (automatically adjusts position, tracking, and sync settings) 6 Aspect button (selects the image aspect ratio) 7 Num button (when held down, switches numeric buttons to number function) 8 Menu button (accesses projector menu system) 9 Arrow buttons (move through on-screen options and control wireless mouse functions) 10 Enter b
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Opening the Lens Cover Projector Placement You can place the projector on almost any flat surface to project your presentation. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings. Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image.
Screen or image size Projection distance 1 50 inches 59 to 71 inches (150 to 180 cm) 2 80 inches 95 to 114 inches (241 to 290 cm) 3 100 inches 119 to 143 inches (302 to 363 cm) 4 150 inches 179 to 215 inches (454 to 546 cm) Wide to Tele VS325W 16:10 Aspect Ratio Screen or image size Projection distance 1 50 inches 55 to 66 inches (139 to 168 cm) 2 80 inches 88 to 106 inches (225 to 270 cm) 3 100 inches 111 to 133 inches (281 to 338 cm) 4 150 inches 167 to 200 inches (424 to 509 c
Connecting to Computer Sources Connecting to Video Sources Connecting to External USB Devices Connecting to a Document Camera Parent topic: Setting Up the Projector Related references Projector Setup Settings - Extended Menu Product Box Contents Connecting to Computer Sources Follow the instructions in these sections to connect a computer to the projector.
4. Connect the other end to any available USB port on your computer. 5. Do one of the following: • Windows 8: Click EPSON_PJ_UD in the upper right-corner, then select Run EMP_UDSe.exe in the dialog box that appears to install the Epson USB Display software. • Windows 7/Windows Vista: Select Run EMP_UDSe.exe in the dialog box that appears to install the Epson USB Display software.
3. Connect the other end to a Computer port on the projector. 4. Tighten the screws on the VGA connectors. Parent topic: Connecting to Computer Sources Related tasks Connecting to a Computer for Sound Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Connecting to a Computer for USB Mouse Control If you connected your computer to a Computer, USB TypeB, or HDMI port on the projector, you can set up the remote control to act as a wireless mouse. This lets you control computer presentations at a distance from your computer. To do this, connect the projector to your computer using a USB cable, if it is not connected already. 1. Connect the USB cable to your projector's USB TypeB port. 2. Connect the other end to any available USB port on your computer. 3.
2. Connect the other end to the projector's Audio ports. Parent topic: Connecting to Computer Sources Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
Parent topic: Connecting to Video Sources Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using a componentto-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable. 1. Connect the component connectors to your video source's color-coded component video output ports, usually labeled Y, Pb, Pr or Y, Cb, Cr.
2. Connect the other end to the projector's Video port. Parent topic: Connecting to Video Sources Related tasks Connecting to a Video Source for Sound Connecting to an S-Video Video Source If your video source has an S-Video port, you can connect it to the projector using an optional S-Video cable. 1. Connect the S-Video cable to your video source's S-Video output port. 2. Connect the other end to the projector's S-Video port.
Connecting to a Video Source for Sound You can play sound through the projector's speaker system if your video source has audio output ports. Connect the projector to the video source using an RCA audio cable. 1. Connect the audio cable to your video source's audio-out ports. 2. Connect the other end of the cable to the projector's Audio port or ports.
Note: Digital cameras or camera phones must be USB-mounted devices, not TWAIN-compliant devices. You can project slide shows from image files on a connected USB device or memory card reader. Parent topic: Connecting to External USB Devices Related topics Projecting a Slide Show Connecting a USB Device or Camera to the Projector You can connect your USB device or camera to the projector's USB TypeA port and use it to project images and other content. 1.
2. Press the USB button on the remote control. 3. Press the button again to cycle through other USB sources, if available. Parent topic: Connecting to External USB Devices Disconnecting a USB Device or Camera From the Projector When you finish presenting with a connected USB device or camera, you must prepare to disconnect the device from the projector. 1. If the device has a power button, turn off and unplug the device. 2. Disconnect the USB device or camera from the projector.
Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Open the battery cover as shown. 2. Insert the batteries with the + and – ends facing as shown.
3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Setting Up the Projector Opening the Lens Cover 1. To open the projector's lens cover, slide the lens cover (VS220) or A/V Mute (VS320/VS325W) slide lever. 2.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. The projector's power light turns orange. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode). Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 4. Press the power button on the projector or the remote control to turn on the projector.
• Insert a DVD or other video media, and press the play button (if necessary). • Press the Source Search button on the projector or remote control to detect the video source. Parent topic: Using Basic Projector Features Related references Projector Setup Settings - Extended Menu Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown.
3. To transport or store the projector, make sure the power light is orange (but not flashing), then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange. 4. Close the projector's lens cover.
Parent topic: Using Basic Projector Features Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus.
2. To adjust the front foot, pull up on the foot release lever and lift the front of the projector. The foot extends from the projector. 3. Release the lever to lock the foot. 4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape.
Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality. When you turn on automatic keystone correction in your projector's Settings menu, your projector automatically corrects vertical keystone effects when you reposition the projector.
3. Press a keystone button on the projector's control panel to adjust the image shape. Note: The horizontal keystone adjustment buttons are labeled Wide and Tele on the VS220. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape using the Keystone settings in the projector menus.
2. Adjust the slider until the image is evenly rectangular. After correction, your image is slightly smaller. Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Correcting Image Shape with Quick Corner You can use the projector's Quick Corner setting (VS320/VS325W) to correct the shape and size of an image that is unevenly rectangular on all sides. 1. Turn on the projector and display an image.
3. Select the Settings menu and press Enter. 4. Select the Keystone setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen.
6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter. 7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc.
Parent topic: Image Shape Resizing the Image You can resize the image using the projector's zoom ring or the Wide and Tele buttons, depending on the projector model. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. • If the projector includes a zoom ring, rotate it to enlarge or reduce the image size. • If the projector includes Wide and Tele buttons, press the Wide button on the projector's control panel to enlarge the image size.
2. To sharpen the image focus, rotate the projector’s focus ring. 1 VS320/VS325W 2 VS220 Parent topic: Using Basic Projector Features Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here.
1 19.7 feet (6 m) 2 ± 30º 3 ± 15º Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
1. Connect the projector to a computer using the projector's USB TypeB, Computer, or HDMI port to display video. 2. If you connected your computer to the Computer or HDMI port, also connect a USB cable to the projector's USB TypeB port and to a USB port on your computer (for wireless mouse support). 3. Start your presentation. 4. Use the following buttons on the remote control to control your presentation: • To move through slides or pages, press the up or down Page buttons.
1. Press the Pointer button on the remote control. 2. Use the arrow buttons on the remote control to move the pointer on the screen. 3. Press Esc to clear the pointer from the screen. Parent topic: Remote Control Operation Related references Projector Feature Settings - Settings Menu Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other. 1.
• Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount. • Rear flips the image horizontally to project from behind a translucent screen.
Changing the Projection Mode Using the Menus You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus. 1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus.
Parent topic: Using Basic Projector Features Related references Image Quality Settings - Image Menu Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3.
Aspect ratio setting Description Normal Displays images using the full projection area and maintains the aspect ratio of the image. 4:3 Displays images using the full projection area at 4:3 aspect ratio. 16:9 Converts the aspect ratio of the image to 16:9. VS325W Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the aspect ratio of the image.
Parent topic: Using Basic Projector Features Related references Image Quality Settings - Image Menu Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3.
Color Mode Description Sports Best for television images in a bright room sRGB Best for standard sRGB computer displays Blackboard Best for presentations onto a green chalkboard (adjusts the colors accordingly) Whiteboard Best for presentations onto a whiteboard (adjusts the colors accordingly) Photo Best for still images projected in a bright room Parent topic: Color Mode Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image base
4. Select the Auto Iris setting and select On. Note: You can turn Auto Iris on or off for each Color Mode that supports the feature. You cannot change the Auto Iris setting when you are using a Closed Caption setting. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Controlling the Volume with the Volume Buttons You can use the Volume buttons on the remote control to adjust the volume as you project a presentation with audio.
Supported Slideshow File Types You can project these types of files using the projector's Slideshow feature. Note: For best results, place your files on media that is formatted in FAT16/32. File contents File type (extension) Details Image .jpg Make sure the file is not: • CMYK format • Progressive format • Highly compressed • Above 8192 × 8192 resolution .bmp Make sure the file resolution is not above 1280 × 800 .gif Make sure the file is not: • Above 1280 × 800 resolution • Animated .
2. Do the following as necessary to locate your files: • If you need to display files inside a subfolder on your device, press the arrow buttons to highlight the folder and press the Enter button. • To move back up a folder level on your device, highlight Back to Top and press Enter. • To view additional images in a folder, highlight Next page or Previous page and press Enter. 3.
Related tasks Disconnecting a USB Device or Camera From the Projector Slideshow Display Options You can select these display options when using the projector's Slideshow feature.
Setting Options Description Effect Wipe Transitions between images with a wipe effect Dissolve Transitions between images with a dissolve effect Random Transitions between images using a random variety of effects Parent topic: Starting a Slide Show 65
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Stopping Video Action Temporarily Zooming Into and Out of Images Projector Security Features Shutting Off the Picture and Sound Temporarily You can temporarily turn off the projected picture and sound if you want to redirect your audience's attention during a presentation.
Stopping Video Action Temporarily You can temporarily stop the action in a video or computer presentation and keep the current image on the screen. Any sound or video action continues to run, however, so you cannot resume projection at the point that you stopped it. 1. Press the Freeze button on the remote control to stop the video action. 2. To restart the video action in progress, press Freeze again.
• To pan around the zoomed image area, use the arrow buttons. • To zoom out of the image, press the E-Zoom – button as necessary. • To return to the original image size, press Esc. Parent topic: Adjusting Projector Features Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings.
1. Hold down the Freeze button on the remote control until you see the Password Protect menu. This takes about five seconds. 2. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?". 3. Select Yes and press Enter. 4. Hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5. Enter the password again.
Parent topic: Password Security Types Selecting Password Security Types After setting a password, you see the Password Protect menu. Select the password security types you want to use. If you do not see this menu, hold down the Freeze button on the remote control for five seconds until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protect, press Enter, select On, press Enter again, and press Esc. 2.
You must enter the correct password to use the projector. 1. Hold down the Num button on the remote control while you enter the password using the numeric buttons. The password screen closes. 2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact Epson Support.
Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature). This transferred image is called the User's Logo screen. The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in identifying the projector's owner to help deter theft.
7. Select a zoom percentage and press Enter. You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. Note: It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished. You see a completion message. 9. Press Esc to exit the message screen. 10. Select the Extended menu and press Enter. 11. Select Display and press Enter. 12.
1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Select the Control Panel Lock setting and press Enter. 4. Select one of these lock types and press Enter: • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. 5. Select Yes and press Enter.
• Use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6. To return all the menu settings to their default values, select Reset. 7.
To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Color Adjustment Slider bars for each color Adjusts the intensity of individual hues in the image Auto Iris On Adjusts the projected luminance based on the image brightness when certain Color Modes are selected Off Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode, use the Power Consumption setting.
To change settings for an input source, make sure the source is connected and select that source. Setting Options Description Auto Setup On Automatically optimizes computer image quality (when On) Off Resolution Auto Sets the input signal resolution if not detected automatically using the Auto option Normal Wide Tracking Varying levels available Adjusts signal to eliminate vertical stripes in computer images Sync.
Setting Options Description HDMI Video Range Normal Sets the video range to match the setting of the device connected to the HDMI input port Expanded Auto Auto: detects the video range automatically Expanded: normally for images from a computer; can also be selected if the image is too dark Normal: normally for images from a device other than a computer; can also be selected if the black areas of the image are too bright Input Signal Auto Specifies the signal type from input sources connected to c
Setting Options Description Overscan Auto (VS320/VS325W) Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 4% 8% Parent topic: Adjusting the Menu Settings Related references Available Image Aspect Ratios Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
Setting Options Keystone H/V Keystone Description Adjusts image shape to rectangular (horizontally and Quick Corner (VS320/VS325W) vertically) H/V Keystone: lets you manually correct horizontal and vertical sides Quick Corner: select to correct image shape and alignment using an on-screen display Zoom Varying levels available Adjusts the size of the projected image Control Panel Lock Full Lock Controls projector button locking to secure the projector Partial Lock Full Lock: locks all buttons O
Setting Options Description Remote Receiver Front Limits reception of remote control signals by the selected receiver; Off turns off all receivers Rear Front/Rear Off User Button Power Consumption Info Assigns a menu option to the User button on the remote control for one-touch access Progressive Closed Caption Test Pattern Resolution Test Pattern On Displays a test pattern to assist in focusing and zooming the image and correcting image shape (press Esc to cancel pattern display) Off Parent to
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen A/V Mute Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Closed Caption Off Controls use of closed captions and se
Setting Options Description User's Logo – Creates a screen that the projector displays to identify itself and enhance security Projection Front Selects the way the projector faces the screen so the image is oriented correctly Front/Ceiling Rear Rear Ceiling Operation Direct Power On Selects various operation options Sleep Mode Direct Power On: turns on the projector when you plug it in Sleep Mode Timer Lens Cover Timer High Altitude Mode Sleep Mode: automatically turns off the projector after
Setting Options Description USB Type B USB Display Selects the use of the projector's USB TypeB port Link 21L USB Display: select when you connect a computer to the projector's USB TypeB port to display images Link 21L: allows a remote Windows computer to operate the projector over a USB connection using the Link 21L Utility Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option) Parent topic: Adjusting the Menu Settings Proj
Note: The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours. Available settings depend on the current input source.
You cannot reset the following settings using the Reset All option: • Input Signal • User's Logo • Language • Lamp Hours • Password • User Button Parent topic: Adjusting the Menu Settings 89
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue.
Cleaning the Air Filter and Vents Clean the projector's air filter or vents if they get dusty, or if you see a message telling you to clean them. 1. Turn off the projector and unplug the power cord. 2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Caution: Do not use canned air.
2. Carefully open the air filter cover. 3. Pull the air filter out of the projector. Note: Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown. 5. Close the air filter cover. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Projector Information Display - Info Menu Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2. Allow the projector lamp to cool down for at least one hour. 3.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out.
6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Press the handle down until it locks into place. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure.
8. Push in the lamp firmly and tighten the screws to secure it. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on.
Reset the lamp timer to zero to keep track of the new lamp’s usage. Parent topic: Projector Lamp Maintenance Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly. Note: Do not reset the lamp timer if you have not replaced the lamp to avoid inaccurate lamp usage information. 1. Turn on the projector. 2. Press the Menu button. 3.
Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Open the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands.
3. Insert the batteries with the + and – ends facing as shown. 4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Transporting the Projector The projector contains precision parts, some of which are glass. Follow these guidelines to transport or ship the projector safely: • Close the lens cover to protect the lens. • Remove any equipment connected to the projector. • Use a carrying case to hand-carry the projector. • When transporting the projector a long distance or as checked luggage, place it in a carrying case. Then pack the case in a firm box with cushioning around it and mark the box "Fragile.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
1 Power light 2 Lamp light 3 Temperature light Power light Lamp light Temperature light Status and solution Green Off Off Normal operation. Flashing green Off Off Warming up. Wait for an image to appear. Orange Off Off Standby or sleep mode. Flashing orange Off Off Preparing for monitoring or shutting down. (When the light remains orange, you can unplug the projector.) Flashing red Flashing orange Projector is too hot.
Power light Lamp light Temperature light Status and solution Red Off Red Projector has overheated and turned off. Leave it turned off to cool down for five minutes. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • Clean or replace the air filter. • If operating the projector at high altitude, turn on High Altitude Mode. • If the problem persists, unplug the projector and contact Epson for help. Red Flashing red Off Lamp has a problem.
Where to Get Help Related tasks Cleaning the Air Filter and Vents Replacing the Air Filter Replacing the Lamp Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 1. Turn on the projector. 2. Press the Help button on the projector or the remote control. You see the Help menu. 3. Use the up and down arrow buttons to highlight the problem you want to solve. 4. Press Enter to view the solutions. 5.
Solutions When the Image Brightness or Colors are Incorrect Solutions to Sound Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Make sure the lens cover is open or off. • Press the A/V Mute button on the remote control to see if the image was temporarily turned off. • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources.
Solutions When Image is Incorrect Using the USB Display Function If no image appears or if the image appears incorrectly using the USB Display function, try the following solutions: • Press the USB button on the remote control. • Make sure the USB Display software has installed correctly. Install it manually if necessary. • Make sure the USB Type B setting in the Extended menu is set to USB Display, if available. • With Mac OS X, select the USB Display icon in the Dock or from the Applications folder.
Displaying From a PC Laptop If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor. 1. Hold down the laptop's Fn key and press the key labelled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear. 2. To display on both the laptop's monitor and the projector, try pressing the same keys again. 3.
Solutions When Only a Partial Image Appears If only a partial computer image appears, try the following solutions: • Press the Auto button on the remote control to optimize the image signal. • Try adjusting the image position using the Position menu setting. • Press the Aspect button on the remote control to select a different image aspect ratio. • If you zoomed into or out of the image using the E-Zoom buttons, press the Esc button twice to return to a full display.
Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector. They should be: • Separated from the power cord to prevent interference • Securely connected at both ends • Not connected to an extension cable • Check the settings on the projector's Signal menu to make sure they match the video source.
• Position the projector close enough to the screen. • Position the projector so the keystone adjustment angle is not so wide that it distorts the image. • Turn on automatic keystone adjustment in the projector's menus. • Adjust the Sharpness setting to improve image quality. • If you are projecting from a computer, press the Auto button on the remote control to automatically adjust the tracking and sync.
Related concepts Projector Lamp Maintenance Related references Input Signal Settings - Signal Menu Image Quality Settings - Image Menu Projector Feature Settings - Settings Menu Solutions to Sound Problems If there is no sound when you expect it or the volume is too low or high, try the following solutions: • Adjust the projector's volume settings. • Press the A/V Mute button on the remote control to resume video and audio if they were temporarily stopped.
Solutions to Projector Power or Shut-Off Problems If the projector does not come on when you press the power button or it shuts off unexpectedly, try the following solutions: • Make sure the power cord is securely connected to the projector and to a working electrical outlet. • The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector. • The power cord may be defective. Disconnect the cord and contact Epson.
• If available, turn off one of the remote receivers in the projector's menu system, or check if all the remote receivers were turned off. • If you assigned an ID number to the remote control to operate multiple projectors, you may need to check or change the ID setting (feature not available with all projectors). • If you lose the remote control, you can order another one from Epson.
Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Technical Specifications These sections list the technical specifications of your projector.
Brightness Normal Power Consumption mode: White light output 2700 lumens (ISO 21118 standard) Color light output 2700 lumens ECO Power Consumption mode: White light output 2160 lumens (ISO 21118 standard) Contrast ratio 3000:1 with Normal Power Consumption mode Image size VS220: 28 to 350 inches (0.71 to 8.89 m) VS320: 28 to 300 inches (0.71 to 7.62 m) VS325W: 29 to 320 inches (0.74 to 8.13 m) Projection distance VS220: 34 to 411 inches (0.86 to 10.44 m) VS320: 35 to 425 inches (0.89 to 10.
Zoom ratio VS220: (Tele-to-Wide) 1:1.35 VS320/VS325W: 1:1.2 Internal sound system 2 W monaural Noise level 37 dB (Normal Power Consumption mode) 29 dB (ECO Power Consumption mode) Keystone correction angle Vertical: ± 30º Horizontal: ± 30º (VS320/VS325W) USB Type B port compatibility USB 1.1 and 2.0 compliant for USB display or external mouse USB Type A port compatibility One USB 1.1 and 2.
Remote Control Specifications Reception range 19.7 feet (6 m) Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 3.03 inches (77 mm) Width 11.6 inches (295 mm) Depth 8.98 inches (228 mm) Weight 5.1 lb (2.3 kg) Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% 2.9 to 1.
Parent topic: Technical Specifications Projector Environmental Specifications Temperature Operating: 41 to 95 ºF (5 to 35 ºC) Storage: 14 to 140 ºF (–10 to 60 ºC) Humidity (relative, noncondensing) Operating: 20 to 80% Operating altitude Up to 4921 feet (1500 m) Storage: 10 to 90% Up to 7500 feet (2286 m) with High Altitude Mode enabled Parent topic: Technical Specifications Projector Safety and Approvals Specifications United States FCC Part 15 Class B (DoC) UL60950-1 Canada ICES-003 Class B CS
Display format Refresh rate (in Hz) Resolution (in pixels) VGA 60/72/75/85 640 × 480 SVGA 56/60/72/75/85 800 × 600 XGA 60/70/75/85 1024 × 768 WXGA 60 1280 × 768 60 1360 × 768 60/75/85 (VS320/VS325W) 1280 × 800 WXGA+ 60/75/85 (VS320/VS325W) 1440 × 900 SXGA 70/75/85 (VS320/VS325W) 1152 × 864 60/75 (VS320/VS325W)/85 (VS320/VS325W) 1280 × 960 60/75 (VS320/VS325W)/85 (VS320/VS325W) 1280 × 1024 SXGA+ 60/75 (VS320/VS325W) 1400 × 1050 UXGA (VS320/VS325W) 60 1600 × 1200 WSXGA+* (VS
Display format Refresh rate (in Hz) Resolution (in pixels) SDTV (480p) 60 720 × 480 SDTV (576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 SXGA 60 1280 × 960 60 1280 × 1024 SXGA+ 60 1400 × 1050 UXGA 60 1600 × 1200 SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30/50/60
Requirement Windows Mac Operating system Windows 2000 (Service Pack 4 only) Mac OS X 10.5.8, 10.6.x, 10.7.x, or 10.8.x Windows XP Professional, Home Edition, and Tablet PC Edition (32-bit); except for Service Pack 1 Windows Vista Ultimate, Enterprise, Business, Home Premium, and Home Basic (32-bit) Windows 7 Ultimate, Enterprise, Professional, and Home Premium (32and 64-bit); Home Basic and Starter (32bit) Windows 8, Windows 8 Enterprise and Pro (32- and 64-bit) USB version USB 1.1 and above (USB 2.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Trademarks Software Copyright Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to www.epson.com/recycle for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 30° forward or back.
• Never allow objects of any kind to enter any openings in the projector. Do not leave objects, especially flammable objects, near the projector. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector.
• Do not store the projector outside of the required temperature range of 14 to 140 ºF (–10 to 60 ºC) or in direct sunlight for long periods of time. Doing so may cause damage to the case. • Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use.
Restriction of Use When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive; disaster prevention devices; various safety devices; or functional/precision devices, you should use this product only after giving consideration to including failsafes and redundancies into your design to maintain safety and total system reliability.
For Canadian Users This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. Parent topic: Notices Trademarks EPSON®, Instant Off®, PowerLite®, and Quick Corner® are registered trademarks, and EPSON Exceed Your Vision is a registered logomark of Seiko Epson Corporation.
The list of GPL Programs is as follows and the names of author are described in the source code of the GPL Programs The list of GPL Programs • busybox-1.13.4 • iptables-1.4.4 • libgcc1(gcc-4.3.3) • linux-2.6.27 • patches • udhcp 0.9.8 • uvc rev.219 • wireless_tools 29 • EPSON original drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc.
GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright © 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.
GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11.
by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
2. You can use this software for whatever you want. You don't have to pay us. 3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code. In legalese: The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose.
config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable. It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software.
libpng version 1.2.6, September 12, 2004 , is Copyright (c) 2004 Glenn Randers -Pehrson, and is distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors Cosmin Truta libpng versions 1.0.7, July 1, 2000 , through 1.2.5 - October 3, 2002 , are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.
For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of individuals: Andreas Dilger Dave Martindale Guy Eric Schalnat Paul Schmidt Tim Wegner The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc.
zlib This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib". The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of zlib programs M M M M zlib-1.1.4 License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows.
mDNSResponder This projector product includes the open source software program "mDNSResponder" which applies the following license terms "Apache License Version 2.0, January 2004". List of "mDNSResponder" M M M M mDNSResponder-107.6 (only mDNSResponderPosix is used) License terms "Apache License Version 2.0, January 2004" are as follows. Apache License Version 2.0, January 2004 http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions.
shall not include works that remain separable from, or merely link (or bind by name) to the interfaces of, the Work and Derivative Works thereof. "Contribution" shall mean any work of authorship, including the original version of the Work and any modifications or additions to that Work or Derivative Works thereof, that is intentionally submitted to Licensor for inclusion in the Work by the copyright owner or by an individual or Legal Entity authorized to submit on behalf of the copyright owner.
excluding those notices that do not pertain to any part of the Derivative Works, in at least one of the following places: within a NOTICE text file distributed as part of the Derivative Works; within the Source form or documentation, if provided along with the Derivative Works; or, within a display generated by the Derivative Works, if and wherever such third-party notices normally appear. The contents of the NOTICE file are for informational purposes only and do not modify the License.
Contributor, and only if You agree to indemnify, defend, and hold each Contributor harmless for any liability incurred by, or claims asserted against, such Contributor by reason of your accepting any such warranty or additional liability. END OF TERMS AND CONDITIONS APPENDIX: How to apply the Apache License to your work. To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information.
(1) Red Hat Incorporated Copyright (c) 1994-2007 Red Hat, Inc. All rights reserved. This copyrighted material is made available to anyone wishing to use, modify, copy, or redistribute it subject to the terms and conditions of the BSD License. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY expressed or implied, including the implied warranties of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. A copy of this license is available at http://www.opensource.
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY.
29K Support Products Mail Stop 573 5900 E. Ben White Blvd. Austin , TX 78741 800-292-9263 (5) C.W. Sandmann Copyright (C) 1993 C.W. Sandmann This file may be freely distributed as long as the author's name remains. (6) Eric Backus (C) Copyright 1992 Eric Backus This software may be used freely so long as this copyright notice is left intact. There is no warrantee on this software. (7) Sun Microsystems Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved.
(11) Christopher G. Demetriou Copyright (c) 2001 Christopher G. Demetriou All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
San Jose CA 95134 USA (13) Royal Institute of Technology Copyright (c) 1999 Kungliga Tekniska H M M gskolan (Royal Institute of Technology , Stockholm , Sweden ). All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
All rights reserved. Redistribution and use in source and binary forms is permitted provided that the above copyright notice and following paragraph are duplicated in all such forms. This file is distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. (23) Intel (i960) Copyright (c) 1993 Intel Corporation Intel hereby grants you permission to copy, modify, and distribute this software and its documentation.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Copyright (c) 1998, M. Warner Losh All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (33) - Daniel Eischen (targets using libc/posix) Copyright (c) 2001 Daniel Eischen . All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * * * Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * * Redistributions in binary form must reproduce the above * copyright * notice, this list of conditions and the following disclaimer * in the documentation and/or other materials provided with * the distribution.
Parent topic: Notices Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.
