Home Cinema 3200/3800 User's Guide
Contents Home Cinema 3200/3800 User's Guide...................................................................................................... 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents......................................................
Selecting Wireless Network Settings Manually.............................................................................. Wireless LAN Menu Settings .................................................................................................... Restricted IP Addresses ........................................................................................................... Using a QR Code to Connect a Mobile Device ..............................................................................
Changing the Color Mode.............................................................................................................. 72 Available Color Modes................................................................................................................... 72 Turning On Auto Iris....................................................................................................................... 73 Adjusting Projector Features ...............................................................
Transporting the Projector................................................................................................................ 120 Solving Problems .................................................................................................................................... Projection Problem Tips ................................................................................................................... Projector Light Status ........................................................
Projector Safety and Approvals Specifications................................................................................. 146 Safety and Approvals Specifications for Latin America .................................................................... 146 Supported Video Display Formats.................................................................................................... 147 Notices ..............................................................................................................
Home Cinema 3200/3800 User's Guide Welcome to the Home Cinema 3200/3800 User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
Easy-to-use setup and operation features • Vertical and horizontal lens shift, and vertical keystone correction buttons for flexible projector placement • 1.6× optical zoom ratio for improved zooming capability Product Box Contents Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Product Box Contents Save all the packaging in case you need to ship the projector.
Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain additional components. Note: To connect a Mac that does not include a compatible video output port, you need to obtain an adapter that allows you to connect to an input port on the projector. Contact Apple for compatible adapter options. To connect a smartphone or tablet, you may need to obtain an adapter that allows you to connect to the projector.
Optional Equipment and Replacement Parts You can purchase screens, other optional accessories, and replacement parts from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales).
• Cautions must be observed to avoid damage to your equipment. • Notes contain important information about your projector. • Tips contain additional projection information. Parent topic: Introduction to Your Projector Where to Go for Additional Information Need quick help on using your projector? Here's where to look for help: • epson.com/support (U.S.), epson.ca/support (Canada), or epson.com.
Projector software Manual Description — Open Source Software License You can download this document from the Epson web site. Go to epson.com/support (U.S.) or epson.ca/support (Canada) and select your projector. Parent topic: Introduction to Your Projector Related references Where to Get Help Projector Part Locations Check the projector part illustrations to learn about the parts on your projector. Note: The Home Cinema 3800 is shown in most illustrations in this manual, unless noted otherwise.
Projector Parts - Front/Top 1 Lamp cover 2 Air exhaust vent 3 Focus ring 4 Lens cap 5 Lens 6 Zoom ring 7 Remote receiver 8 Front adjustable feet 9 Air intake vent/air filter cover 10 Vertical lens shift dial 11 Horizontal lens shift dial 12 Control panel and lights 16
Parent topic: Projector Part Locations Projector Parts - Rear 1 Speakers (Home Cinema 3800) 2 AC input port 3 Trigger Out port (Home Cinema 3800) 4 RS-232C port (Home Cinema 3800) 5 Security cable attachment point 6 Audio Out port 7 Cable holder 8 DC Out (2.
Projector Parts - Base 1 Front adjustable feet 2 Mounting bracket holes 3 Air intake vent Parent topic: Projector Part Locations 18
Projector Parts - Control Panel Home Cinema 3200 1 Lamp light 2 Status light 3 Power button and light 4 Home button 5 Horizontal keystone adjustment buttons (adjust screen shape) and arrow buttons 6 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 7 Esc button (cancels/exits functions) 8 Enter button (selects options) 9 Menu button (accesses projector menu system) 10 Temp light 19
Home Cinema 3800 1 Lamp light 2 Status light 3 Power button and light 4 Home button 5 Volume control buttons, horizontal keystone adjustment buttons (adjust screen shape), and arrow buttons 6 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 7 Esc button (cancels/exits functions) 8 Enter button (selects options) 9 Menu button (accesses projector menu system) 10 Temp light Parent topic: Projector Part Locations 20
Projector Parts - Remote Control 1 On button (turns on projector) 2 Standby button (turns off the projector) 3 Source buttons (select specific video input sources) 4 Pattern button (displays a test pattern) 5 Control buttons (control playback and other features of connected devices that support the HDMI CEC standard) Link Menu button (displays the main menu of the connected device) 21
6 HDMI Link button (displays the settings menu for HDMI Link) 7 Color Mode button (selects display modes) 8 HDR button (displays Dynamic Range menu) 9 Arrow buttons (move though on-screen options) 10 Default button (returns selected setting to default value) 11 Menu button (accesses projector menu system) 12 Fine/Fast button (improves image response time for high frame rate sources) 13 Keystone button (corrects image distortion) 14 User button (customizable for different functions) 15 Mem
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Rear Front Ceiling Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If the projector cannot be centered in front of the screen, use lens shift to reposition the image instead of using keystone correction for better image quality. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system.
Parent topic: Projector Placement Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image. The image size increases the farther the projector is from the screen, but can vary depending on the zoom factor, aspect ratio, and other settings. Use the tables here to determine approximately how far to place the projector from the screen based on the size of the projected image.
Horizontal lens shift adjustment 1 Screen or image size 2 Distance between projector and screen 3 Distance from center of lens to bottom of the projected image when the lens is shifted to the highest position 4 Distance from center of lens to bottom of the projected image when the lens is shifted to the lowest position 5 Distance the projected image moves from the center when the lens is shifted to its maximum position left or right 16:9 Aspect Ratio Image or Screen 26
Screen or image size (1) Projection distance (2) Wide to Tele 40 inches (101.6 cm) 46 to 74 inches (116 to 189 cm) 60 inches (152.4 cm) 69 to 112 inches (175 to 285 cm) 80 inches (203.2 cm) 93 to 150 inches (235 to 381 cm) 100 inches (254 cm) 116 to 188 inches (295 to 477 cm) 120 inches (304.
Screen or image size (1) Projection distance (2) Wide to Tele 40 inches (101.6 cm) 56 to 91 inches (143 to 232 cm) 60 inches (152.4 cm) 85 to 138 inches (215 to 350 cm) 80 inches (203.2 cm) 114 to 184 inches (288 to 467 cm) 100 inches (254 cm) 142 to 230 inches (361 to 585 cm) 120 inches (304.
Projector Connections See these sections to connect the projector to a variety of projection sources. Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.
Parent topic: Projector Connections Related references Projector Feature Settings - Settings Menu Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable. Note: To connect a Mac that includes only a Mini DisplayPort, Thunderbolt port, or Mini-DVI port for video output, you need to obtain an adapter that allows you to connect to the projector's HDMI port. Contact Apple for compatible adapter options. 1.
2. Connect the other end to the projector's Trigger Out port. 3. Turn on the Trigger Out setting in the projector's Extended > Operation menu. Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Connecting to External Speakers To enhance the sound from your presentation, you can connect the projector to external self-powered speakers. You can control the volume using the projector's remote control.
4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port. Parent topic: Projector Connections Related references Projector Feature Settings - Settings Menu Connecting to a Bluetooth Audio Device You can connect your projector to Bluetooth audio devices such as speakers or headphones to output audio from a streaming device or other video source connected to the projector. Note: The Bluetooth audio device must be A2DP compliant. There may be a slight delay in audio output.
3. Select the Settings menu and press Enter. 4. Select HDMI Link and press Enter. 5. Select Audio Out Device and press Enter. 6. Select Projector and press Enter. 7. Press Esc until you return to the Settings menu.
8. Select Bluetooth and press Enter. 9. Select Bluetooth Audio and press Enter. 10. Select On and press Enter. 11. Press Esc to return to the Bluetooth menu. 12. Make sure the Bluetooth audio device you want to connect to is in pairing or discovery mode (see your Bluetooth audio device manual for details). 13. Select Search Bluetooth Device and press Enter to display a list of available devices.
14. Select the device you want to connect to and press Enter. 15. Press the Esc button to return to the previous screen or the Menu button to exit the menu. The next time you turn on the projector, the last connected device is automatically connected. To change the connected device, repeat these steps. Parent topic: Projector Connections Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector.
2. Insert the batteries with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wireless Network Projection Wireless Network Projection You can project over a wireless network. To do this, you must set up your projector and computer for wireless projection. Note: The Epson 802.11b/g/n wireless LAN module is not included with your projector and is optional. To connect wirelessly to your projector, configure the connection using the projector's Network menus.
Insert the wireless LAN module into the USB port. The light on the wireless LAN module turns on when the module is installed and operating. The light flashes when the module is communicating over the network. Parent topic: Wireless Network Projection Related references Optional Equipment and Replacement Parts Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector.
3. Select the Network menu and press Enter. 4. Make sure the Wireless LAN Power setting is set to On. 5. Select Network Configuration and press Enter. 6. Select the Basic menu and press Enter.
7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen on a smartphone or tablet. • Display LAN Info lets you select how the projector displays network information.
Parent topic: Wireless Network Projection Wireless LAN Menu Settings Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick: lets you quickly connect to local devices without an internet connection Advanced: lets you connect to multiple computers via a wireless network access point (infrastructure mode) Channel 1ch In Quick connection mode, selects the frequency band (channel) used by the wireless LAN 6ch 11ch SSID Up 32 alphanumeric characters
Setting Options Description IP Address Display On Selects whether to display the IP address on the network standby screen and the Home screen Off Parent topic: Selecting Wireless Network Settings Manually Related references Restricted IP Addresses Restricted IP Addresses When manually entering IP Settings, you cannot use these ranges of IP addresses: Setting Restricted IP addresses IP Address 0.0.0.0 127.x.x.x 224.0.0.0 to 255.255.255.255 Subnet Mask 0.0.0.0 255.255.255.255 Gateway Address 0.
2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Basic menu and press Enter. 5. Set the Display LAN Info setting to Text & QR Code. 6. Select Complete and follow the on-screen instructions to save your settings and exit the menus.
7. Do one of the following: • Press the LAN button on the remote control. • Select Display the QR Code in the projector's Network menu. • Press the Home button on the remote control and select Display the QR Code on the Home screen. Your projector displays the QR code on the projection surface. Note: If you do not see the QR code after pressing the LAN button, press Enter to display it. 8. Start Epson iProjection on your mobile device. 9.
4. Select Network Configuration and press Enter. 5. Select the Wireless LAN menu and press Enter. 6. Select Advanced as the Connection Mode setting and press Enter. 7. Select Search Access Point and press Enter. 8. Select the name of the wireless network you want to connect to and press Enter. 9. If the network has security enabled, enter the wireless password.
10. Select the settings on the Security menu as necessary for your network. 11. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Parent topic: Wireless Network Projection Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. 1.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Security menu and press Enter. 6. Select the settings on the Security menu as necessary for your network. 7. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Setting Options Description Passphrase — For the selected security, selects the pre-shared passphrase used on the network Parent topic: Enabling WPA or WPA2 Security 48
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Connect the power cord to the projector's power inlet. 3. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 4. Press the power button on the projector or the On button on the remote control to turn on the projector. Warning: Never look into the projector lens when the lamp is on. This can damage your eyes and is especially dangerous for children.
Using the Home Screen You can select input sources and other frequently used options from the Home screen. 1. To display the Home screen, do one of the following: • Press the Home button on the remote control. • Turn on the projector with the Home Screen Auto Disp setting enabled. • Turn on the projector when no signal is received from the selected input source. 2. Press the arrow buttons on the remote control or control panel to navigate the screen, and press Enter to select an option.
Note: You can select the customizable menu options using the Custom Function 1 and Custom Function 2 settings in the Extended menu. 3. Press the Home button to hide the Home screen. Parent topic: Turning On the Projector Related references Projector Setup Settings - Extended Menu Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown.
3. To transport or store the projector, make sure the status light is off, then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the status light is on or flashing. 4. Replace the projector's lens cap.
Viewing 3D Images You can view 3D images using your projector. Viewing 3D images requires a 3D-compatible video device, a compatible HDMI cable, and a pair of Epson RF 3D glasses (not included with your projector). You can purchase Epson RF 3D glasses from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766) in the U.S. or 800-807-7766 in Canada. Or you can purchase online at epsonstore.com (U.S. sales) or epsonstore.ca (Canadian sales).
6. Put on the 3D glasses and view the projected image. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the status light flashes green. Slide the power switch on the glasses to the Off position and then back to the On position to resume 3D viewing. Note: Make sure you are within 32 ft (10 m) of the projector when using the 3D glasses or you may lose your connection.
5. Move the glasses within 10 feet (3 m) of the projector and hold down the Pairing button for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off. Parent topic: Viewing 3D Images Charging the 3D Glasses When the status light on the glasses flashes red to indicate a low battery, it is time to charge the glasses. 1.
• Plug the other end of the charging cable into a USB-to-AC adapter with the following specifications: Input: 100-240V, ~0.15A, 50-60Hz Output: 5V=1A The glasses are fully charged when the status light on the glasses stays green. Parent topic: Viewing 3D Images 3D Viewing Range When you view 3D images, make sure you are positioned within the viewing range shown here.
1. Turn on the projector. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1.
2. If the image is tilted, rotate the front feet to adjust their height. 3. Use the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary. If the projected image is unevenly rectangular, you need to adjust the image shape.
2. Turn the vertical and horizontal lens shift dials on the projector to adjust the position of the projected image as necessary.
3 V × 60% 4 H × 24% Note: You cannot move the image to both the horizontal and vertical maximum values. Parent topic: Using Basic Projector Features Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
1. Turn on the projector and display an image. Note: You can also display the pattern by pressing the Pattern button on the remote control. 2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen.
3. Press a keystone button on the projector's control panel to adjust the image shape. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape with the remote control using the Keystone settings in the projector menus.
3. Select the Settings menu and press Enter. 4. Select the Keystone setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen: 6. Use the arrow buttons on the projector or remote control to select the corner of the image you want to adjust. Then press Enter.
7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc. Parent topic: Image Shape Related references Projector Feature Settings - Settings Menu Resizing the Image with the Zoom Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus for maximum accuracy. Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control. 2.
Focusing the Image Using the Focus Ring 1. Turn on the projector and display an image. Wait 30 minutes after turning on the projector before setting the focus for maximum accuracy. Note: You can display a pattern to aid in adjusting the projected image using the Pattern button on the remote control. 2. To sharpen the image focus, rotate the projector’s focus ring.
Vertical 1 32 feet (10 m) 2 ± 30° Horizontal 1 32 feet (10 m) 2 ± 30° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
Parent topic: Using Basic Projector Features Selecting an Image Source If you connected multiple image sources to the projector, such as a computer and DVD player, you may want to switch from one image source to the other. 1. Make sure the connected image source you want to use is turned on. 2. For video image sources, insert a DVD or other video media and press its play button, if necessary. 3. Press the button for the source you want on the projector's control panel or remote control.
Changing the Projection Mode Using the Menus You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus. 1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus.
Changing the Image Aspect Ratio Available Image Aspect Ratios Parent topic: Using Basic Projector Features Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. Note: For HDMI sources, the input signal determines the image's aspect ratio. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control. A list of the available aspect ratios appears. 3.
Note: Black bands and cropped images may project in certain aspect ratios, depending on the aspect ratio and resolution of your input signal. Aspect ratio setting Description Auto Automatically sets the aspect ratio according to the input signal. Normal Displays images using the full projection area and maintains the aspect ratio of the image. Full Displays images using the full width of the projection area, but does not maintain the aspect ratio.
Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3. Press the Color Mode button on the remote control to change the Color Mode. A list of available Color Modes appears. 4.
Parent topic: Color Mode Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on the brightness of the content you project. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Menu button. Note: You can also press the Auto Iris button on the remote control to access the Auto Iris setting directly. 3. Select the Image menu and press Enter. 4.
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Adjusting the Color Convergence (Panel Alignment) Projector Security Features Saving Settings to Memory and Using Saved Settings Shutting Off the Picture and Sound Temporarily You can temporarily turn off the projected picture and sound if you want to redirect your audience's attention during a presentation.
Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature. For best results, project an image sized at least 60 inches (152 cm) diagonally in a dark room and on a projection surface that is not colored or textured. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Display setting and press Enter. 5. Select the Panel Alignment setting and press Enter. 6.
You see this screen: 12. Select one of the following: • Select Shift the whole panel to adjust the whole panel at the same time. (This is not recommended, as usually only certain areas of the panel need to be adjusted.) Continue with step 13. • Select Adjust the four corners to adjust the corners of the panel one at a time. Skip to step 16. 13. Press Enter.
14. Use the arrow buttons on the remote control to adjust the color alignment of the color you selected for the Select Color setting. 15. When you are finished adjusting the screen, press Enter. You see this screen: Note: The Shift the whole panel option affects the grid lines in the entire screen. To fine-tune your adjustments, continue with the next steps. 16. Select Adjust the four corners and press Enter. (Otherwise, select Exit and press Enter.) 17.
You see this screen: 20. Do one of the following: • If your projector's panel alignment is now correct, select Exit and press Enter to return to the Panel Alignment menu. • If your projector needs additional panel alignment, select Select intersection and adjust and press Enter. Use the arrow keys on the remote control to highlight the corner of any misaligned box on the screen, press Enter, make any necessary adjustments and press Enter again. Repeat this step as necessary for the other intersections.
1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Select the Lock Setting setting and press Enter. 4. Select one of these lock types and press Enter: • To lock the projector's power button, select Child Lock. To turn the projector on, you must press the power button for longer than three seconds. Note: Child Lock does not prevent the projector from turning on when the power cord is connected and the Direct Power On Setting is set to On.
Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the power button on the projector's control panel for seven seconds to unlock them. Parent topic: Locking the Projector's Buttons Installing a Security Cable You can use the security slot on the back of the projector to attach a Kensington lock. See your local computer or electronics dealer for purchase information.
You see this screen: 5. Select one of the following options: • Load Memory: Overwrites your current settings with saved settings • Save Memory: Saves your current settings to memory (10 memories with different names are available) Note: A memory name that has already been used is indicated by a blue mark. Saving over a previously saved memory overwrites the settings with your current settings. • Erase Memory: Erases the selected memory settings • Rename Memory: Renames a saved memory 6. Press Esc to exit.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source, resolution, or other menu settings. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
Note: The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description White Balance Color Temp. Color Temp.
Setting Options Description Power Consumption High Selects the brightness mode of the projector lamp Medium High: sets maximum lamp brightness ECO Medium: reduces the brightness of the lamp ECO: reduces lamp brightness and fan noise, and saves power and lamp life Auto Iris Off Adjusts the projected luminance based on the image brightness when certain Color Modes are selected Normal High Speed Note: Depending on the image, you may hear the Auto Iris operating, but this is not a malfunction.
Setting Description Deinterlacing*1 *2 Sets whether to convert interlaced-to-progressive signals for certain video image types • Off: for fast-moving video images • Video: for most video images • Film/Auto: for movies, computer graphics, and animation Noise Reduction*1 *2 *3 Reduces flickering in analog images *1 *2 *3 MPEG Noise Reduction Reduces the noise or artifacts seen in MPEG video Super-resolution*2 Sharpens blurred images resulting from increasing resolution • Fine Line Adjustment: enhance
Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically. If you need to customize the settings, you can use the Signal menu. Note: The available settings depend on the currently selected input source. You cannot change the Signal menu settings when the LAN source is selected. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description 3D Setup 3D Display Selects various 3D options 3D Format 3D Display: enables 3D mode 3D Depth 3D Format: selects the 3D format Diagonal Screen Size 3D Brightness Inverse 3D Glasses 3D Viewing Notice 3D Depth: sets the depth for the 3D image Diagonal Screen Size: selects the actual size of the screen to maximize the 3D effect 3D Brightness: adjusts the brightness of the 3D image Inverse 3D Glasses: reverses the images projected for the left and right eyes (enable only i
Setting Options Description Color Space Auto Sets the conversion system for the color space BT.709 Dynamic Range BT.2020 Note: Selecting the incorrect color space for the input source may adversely affect the image colors. The recommended setting in most cases is Auto.
Setting Options Description Advanced Video Range Video Range: sets the video range to match the setting of the device connected to the HDMI input port EDID Image Processing EDID: sets the EDID settings; select Normal for 3840 × 2160 30Hz signals; select Expanded for 3840 × 2160 60Hz signals Image Processing: adjusts how images are processed; select Fast to display images quicker; select Fine to display images in higher quality Note: The Fast setting disables some Image Enhancement settings.
Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features. Setting Options Description Keystone H/V-Keystone Adjusts the projected image shape Quick Corner H/V Keystone: lets you manually correct the angles of the horizontal and vertical sides Quick Corner: select to adjust the position of the four corners Blanking — Covers part of the image with a black box. Can be used to hide raster lines from certain signals such as broadcast content.
Setting Options Description HDMI Link Device Connections Adjusts options that allow the projector remote to control HDMIconnected devices HDMI Link Audio Out Device Power On Link Power Off Link Link Buffer Device Connections: lists the devices connected to the HDMI1 and HDMI2/MHL ports HDMI Link: enables or disables HDMI Link Audio Out Device: selects which device or port outputs audio.
Setting Options Description Bluetooth Search Bluetooth Device Search Bluetooth Device: searches for available Bluetooth devices Bluetooth Audio Connected Device Bluetooth Audio: turns Bluetooth Audio on or off Connected Device: displays information for the connected Bluetooth Audio device Lock Setting Child Lock Control Panel Lock Controls control panel button locking to secure the projector Child Lock: locks the power button when the projector is off Control Panel Lock: • Full Lock: locks all but
Setting Options Description Memory Load Memory Controls the saved projector settings and lens positions Save Memory Erase Memory Rename Memory Load Memory: displays the list of customized settings entries that you have created Save Memory: saves the current projector settings to the projector's memory Erase Memory: lets you delete a saved memory Rename Memory: lets you rename a saved memory using 9 predetermined name types or up to 12 characters in a customized name Parent topic: Adjusting the Menu
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Home Screen Home Screen Auto Disp. Adjust settings on the Home Screen Custom Function 1 Custom Function 2 Home Screen Auto Disp.
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is oriented correctly Front/Ceiling Rear Rear/Ceiling Operation — See the Operation settings table in this topic Standby Mode Communication Off Indicates whether the projector can be monitored over a network connection while in standby mode Communication On Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option) Displa
Setting Description Sleep Mode Automatically places the projector in standby mode after an interval of inactivity Sleep Mode Timer Sets the time before the projector automatically turns off (Sleep Mode must be turned on) from 1 to 30 minutes (30 minutes is the defualt) Illumination Turns off the status light on the projector Trigger Out (Home Cinema 3800) Outputs a 12V DC signal (at a maximum of 200 mA) from the 3.
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network. Setting Options Description Wireless LAN Power On Enable or disable wireless communication Off Net. Info - Wireless LAN Connection mode Wireless LAN Sys.
Setting Options Description Display the QR Code — Displays the QR Code Network Configuration Accesses additional network menus Configures your network settings Parent topic: Adjusting the Menu Settings Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu. However, you cannot change any settings in the menu. Note: To view the firmware version of the projector or other components, select Version.
Information item Description Source Displays the name of the port to which the current input source is connected Input Signal Displays the input signal setting of the current input source Resolution Displays the resolution of the current input source Scan Mode Displays the scan mode of the current input source Refresh Rate Displays the refresh rate of the current input source 3D Format Displays the 3D format of the current input source Sync Info Displays information that may be needed by a se
Event ID Code List If the Event ID option on the Info menu displays a code number, check this list of Event ID codes for the solution to the projector problem associated with the code. Event ID code Cause and solution 0022 Unstable network communication. Check the network communication status, wait a few moments, and try connecting to the network again. 0027 0028 0029 0030 0031 0035 0434 0481 0482 0485 0432 Turn the projector off and then on again. 0435 0433 Cannot display the transferred images.
Event ID code Cause and solution 0894 Communication with unauthorized access point was disconnected. Contact your network administrator. 0898 Failed to acquire DHCP. Make sure the DHCP server is operating correctly. If you are not using DHCP, turn off the DHCP setting in the Network menus. 0020 Communication error. Turn the projector off and then on again.
You cannot reset the following settings using the Reset All option: • Language • Lamp Hours • Memory settings • All settings in the Network menu • Panel Alignment • Color Uniformity Parent topic: Adjusting the Menu Settings 104
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue.
Note: Unplug any charging cables from the glasses before cleaning them. Caution: Do not use paper towels or any other abrasive materials to clean the glasses. Parent topic: Projector Maintenance Air Filter and Vent Maintenance Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance simple. Filter maintenance intervals will depend on the environment.
• You see a message telling you to clean it. 1. Turn off the projector and unplug the power cord. 2. Lift the tab on the bottom of the air filter cover and pull down to remove the cover. 3. Pull the air filter out of the projector.
4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas. 5. Vacuum the front of the air filter (the side with the tabs) to remove any remaining dust.
6. Place the air filter back in the projector as shown. 7. Attach the air filter cover as shown, and press it gently until it clicks into place.
You can replace the air filter while the projector is mounted to the ceiling or placed on a table. 1. Turn off the projector and unplug the power cord. 2. Lift the tab on the bottom of the air filter cover and pull down to remove the cover. 3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown. 5. Attach the air filter cover as shown, and press it gently until it clicks into place. Parent topic: Air Filter and Vent Maintenance Related references Optional Equipment and Replacement Parts Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Replace the lamp as soon as possible when the following occurs: • The projected image gets darker or starts to deteriorate • A message appears when you turn on the projector telling you to replace the lamp • The projector's Lamp light is flashing orange and its power light is flashing blue Replacing the Lamp Resetting the Lamp Timer Parent topic: Projector Maintenance Related references Projector Information Display - Info Menu Optional Equipment and Replacement Parts Projector Light Status Replacing the La
3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover. Warning: If the lamp is broken, glass fragments may be loose inside the lamp chamber. Be careful removing any broken glass to avoid injury. If the projector is installed on the ceiling, stand to the side of the lamp cover and not underneath it; pieces of glass could fall into your eyes or mouth when you open the lamp cover. 4. Slide the lamp cover out and lift it off.
5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Lower the handle. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 8. Push in the lamp firmly and tighten the screws to secure it.
Caution: Do not over-tighten the screws. 9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp's usage.
1. Turn on the projector. 2. Press the Menu button. 3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter. You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out.
1. Remove the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Specifications Transporting the Projector The projector contains precision parts, some of which are glass.
• When transporting the projector a long distance or as checked luggage, pack it in a firm box with cushioning around it and mark the box "Fragile." • When shipping the projector for repairs, place it in its original packing materials, if possible, or use equivalent materials with cushioning around the projector. Mark the box "Fragile." Note: Epson shall not be liable for any damages incurred during transportation.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solutions When Wireless Authentication Fails Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
Status light Power light Lamp light Temp light Status and solution Blue Blue Off Projector is too hot Flashing orange • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure the environmental temperature is not too hot Flashing blue Off Off Orange Projector has overheated and turned off; leave it turned off to cool down for about five minutes, then do the following: • Make sure that the vents and air filte
Status light Power light Lamp light Temp light Status and solution Flashing blue Off Off Flashing orange A fan or sensor has a problem; turn the projector off, unplug it, and contact Epson for help Flashing blue Off Flashing orange Flashing orange Auto Iris error; turn the projector off, unplug it, and contact Epson for help Flashing blue Off Orange Orange Power error; turn the projector off, unplug it, and contact Epson for help Flashing blue Off Flashing orange Off Internal projector er
Solutions When the Image Contains Noise or Static Solutions When the Image is Fuzzy or Blurry Solutions When the Image Brightness or Colors are Incorrect Solutions When a 3D Image Does Not Display Correctly Solutions to Panel Alignment Problems Solutions to Sound Problems Solutions to Bluetooth Audio Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Make sure the lens cap is off.
Solutions When "No Signal" Message Appears If the "No Signal" message appears, try the following solutions: • Press a source button on the remote to select an available source. Wait a few seconds for an image to appear. • Press the Home button on the remote control to select from a list of available sources. • Turn on the connected computer or video source, and press its play button to begin your presentation, if necessary. • Check the connection from the projector to your video sources.
2. If the same image is not displayed by the laptop and projector, check the Windows Display utility to make sure the external monitor port is enabled and extended desktop mode is disabled. (See your computer or Windows manual for instructions.) 3. If necessary, check your video card settings and set the multiple display option to Clone, Mirror, or Duplicate.
• Check the cables connecting the computer or video source to the projector. Try connecting different cables. • Check your computer display settings to disable dual display and set the resolution within the projector's limits. (See your computer manual for details.) • Check the resolution assigned to your presentation files to see if they are created for a different resolution than you are projecting in. (See your software help for details.
Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector. They should be: • Separated from the power cord to prevent interference • Securely connected at both ends • Not connected to an extension cable • No longer than 24 feet (7.
• Position the projector close enough to the screen, and directly in front of it. • Position the projector so the keystone adjustment angle is not so wide that it distorts the image. • Adjust the Sharpness setting to improve image quality. • If you are projecting from a computer, adjust the computer's resolution to match the projector's native resolution, if possible. • Check the resolution of your video source.
Input Signal Settings - Signal Menu Related tasks Replacing the Lamp Solutions When a 3D Image Does Not Display Correctly If a 3D image does not display correctly, try the following solutions: • Press the 3D Format button on the remote control to switch to 3D mode, if necessary. You can also activate 3D mode by setting the 3D Display setting on the Signal menu to On. • Make sure your video device and media are both 3D-compatible.
Related tasks Pairing the 3D Glasses with the Projector Charging the 3D Glasses Cleaning the 3D Glasses Solutions to Panel Alignment Problems If the panel alignment does not result in a satisfactory picture, try the following solutions: • Make sure the Projection setting matches the installation position. • Make sure the projection surface is not colored or textured. Project on a white surface with no texture. • Leave the projector on for 10 to 15 minutes before adjusting the panel alignment.
• Check the audio cable connections between the projector and your video source. • Make sure any connected audio cables are labeled "No Resistance." • If you turn the projector on immediately after turning it off, the cooling fans may run at high speed momentarily and cause an unexpected noise. This is normal.
Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control.
Solutions to Remote Control Problems If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries. • Make sure you are operating the remote control within the reception angle and range of the projector. • Make sure the projector is not warming up or shutting down. • Check to see if a button on the remote control is stuck down, causing it to enter sleep mode.
• If you connected a new device or changed any connections, make sure the CEC function is set for the connected device. You may need to restart the device. • Connect no more than two devices that support HDMI Link at the same time. • If you have connected a speaker or receiver, set the output to PCM.
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839 (Canada). Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Technical Specifications These sections list the technical specifications of your projector.
Contrast ratio Home Cinema 3200: Up to 40000:1 with Auto Iris on and a variety of other settings selected Home Cinema 3800: Up to 100000:1 with Auto Iris on and a variety of other settings selected Image size 40 inches (1.02 m) to 300 inches (7.6 m) (in native aspect ratio) Projection distance 116.1 inches (2.95 m) to 187.8 inches (4.
Projector Lamp Specifications Type UHE (Ultra High Efficiency) Power consumption 250 W Lamp life High Power Consumption mode: Up to about 3500 hours Medium Power Consumption mode: Up to about 4000 hours ECO Power Consumption mode: Up to about 5000 hours Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time.
Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 6.2 inches (157 mm) Width 16.1 inches (410 mm) Depth (with lens) 13 inches (330 mm) Weight Home Cinema 3200: 14.6 lb (6.6 kg) Home Cinema 3800: 15.2 lb (6.9 kg) For mounting 1 Center of lens 2 Distance from center of lens to suspension bracket fixing point: 3.5 inches (90 mm) 3 16.1 inches (410 mm) 4 5.6 inches (143.
5 6.5 inches (164 mm) 1 11.8 inches (300 mm) 2 1.8 inches (44.5 mm) 3 5.9 inches (150 mm) 4 13 inches (330 mm) 5 3.4 inches (87.6 mm) 6 6.
Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% Home Cinema 3200: 3.9 to 1.7 A Home Cinema 3800: 4.1 to 1.8 A Power consumption Operating: (100 to 120 V) Home Cinema 3200: High Power Consumption mode: 386 W Medium Power Consumption mode: 359 W ECO Power Consumption mode: 291 W Home Cinema 3800: High Power Consumption mode: 406 W Medium Power Consumption mode: 376 W ECO Power Consumption mode: 309 W Standby: 0.5 W (Communication Off), 2.
Power consumption Operating: (220 to 240 V) Home Cinema 3200: High Power Consumption mode: 368 W Medium Power Consumption mode: 343 W ECO Power Consumption mode: 280 W Home Cinema 3800: High Power Consumption mode: 387 W Medium Power Consumption mode: 363 W ECO Power Consumption mode: 297 W Standby: 0.5 W (Communication Off), 2.
Projector Safety and Approvals Specifications United States FCC Part 15 Class B UL60950-1 2nd edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No.
Av. Gral. Bernardino Caballero 810 esq.
Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV (720p) 50/60 1280 × 720 Frame Packing Side by Side Top and Bottom HDTV (1080i) 50/60 1920 × 1080 Side by Side HDTV (1080p) 50/60 1920 × 1080 Side by Side 24 1920 × 1080 Frame Packing Side by Side Top and Bottom Note: Frame sequential 3D is not supported.
Display format (refresh rate) Chroma subsampling (pixel encoding) Color depth: 24 bits (8-bits per pixel) Color depth: 30 bits (10-bits per pixel) Color depth: 36 bits (12-bits per pixel) 4K/60p (60 Hz) 4:4:4* HDR HDR HDR 4:2:2 HDR HDR HDR 4:2:0 HDR HDR HDR 4:4:4 HDR HDR HDR 4:2:2 HDR HDR HDR 4:2:0 This signal does not exist. 4K/24p (24 Hz) *4:4:4 10-bit and 12-bit are displayed at 4:2:2.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Warning Labels Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) FCC Compliance Statement Binding Arbitration and Class Waiver Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
Warning Labels This product comes with warning labels. As with any bright source, do not stare into the beam (RG2 IEC/EN 62471-5:2015). Parent topic: Notices Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. Avoid standing in front of the projector so the bright light does not shine into your eyes.
projector to fall from its ceiling mount. This could cause serious injury to anyone under the mount and could damage the projector. • Do not use the projector near water, sources of heat, high-voltage electrical wires, or sources of magnetic fields. • Use the type of power source indicated on the projector. Use of a different power source may result in fire or electric shock. If you are not sure of the power available, consult your dealer or power company.
• Never open any covers on the projector except as specifically explained in this manual. Never attempt to disassemble or modify the projector. Refer all repairs to qualified service personnel.
• Do not place the source of an open flame, such as a lit candle, on or near the projector. • Do not block the lens during projection using a book or any other object. This could damage the projector or cause a fire. • Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or pull it excessively. Keep the power cord away from hot electrical appliances.
No. 1 2 3 4 Symbol Approved Standards Description IEC60417 "ON" (power) No.5007 To indicate connection to the mains. IEC60417 "OFF" (power) No.5008 To indicate disconnection from the mains. IEC60417 Standby No.5009 To identify the switch or switch position by means of which part of the equipment is switched on in order to bring it into the standby condition. ISO7000 Caution No.0434B To identify general caution when using the product. IEC3864-B3.
No. 8 9 10 11 12 13 Symbol Approved Standards Description IEC60417 Polarity of DC power connector No.5926 To identify the positive and negative connections (the polarity) on a piece of equipment to which a DC power supply may be connected. IEC60417 Battery, general No.5001B On battery powered equipment. To identify a device for instance a cover for the battery compartment, or the connector terminals. IEC60417 Positioning of cell No.
No. 14 15 16 Symbol Approved Standards Description IEC60417 Direct current No.5031 To indicate on the rating plate that the equipment is suitable for direct current only; to identify relevant terminals. IEC60417 Class II equipment No.5172 To identify equipment meeting the safety requirements specified for Class II equipment according to IEC 61140. ISO 3864 General prohibition To identify actions or operations that are prohibited.
No. Symbol 22 23 Approved Standards Description IEC60417 Standby, partial standby No. 5266 To indicate that part of the equipment is in the ready status. ISO3864 Caution, movable parts IEC60417 To indicate that you must keep away from movable parts according to protection standards. No. 5057 24 IEC60417-6056 Caution, moving fan blades To indicate that you must keep away from moving fan blades. 25 IEC60417-6043 Caution, sharp corners To indicate that you must not touch sharp corners.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Binding Arbitration and Class Waiver 1. DISPUTES, BINDING INDIVIDUAL ARBITRATION, AND WAIVER OF CLASS ACTIONS AND CLASS ARBITRATIONS 1.1 Disputes. The terms of this Section 1 shall apply to all Disputes between you and Epson.
1.5 WAIVER OF CLASS ACTIONS AND CLASS ARBITRATIONS. YOU AND EPSON AGREE THAT EACH PARTY MAY BRING DISPUTES AGAINST THE OTHER PARTY ONLY IN AN INDIVIDUAL CAPACITY, AND NOT AS A PLAINTIFF OR CLASS MEMBER IN ANY CLASS OR REPRESENTATIVE PROCEEDING, INCLUDING WITHOUT LIMITATION FEDERAL OR STATE CLASS ACTIONS, OR CLASS ARBITRATIONS. CLASS ACTION LAWSUITS, CLASS-WIDE ARBITRATIONS, PRIVATE ATTORNEY-GENERAL ACTIONS, AND ANY OTHER PROCEEDING WHERE SOMEONE ACTS IN A REPRESENTATIVE CAPACITY ARE NOT ALLOWED.
(iii) Send one copy of the Demand for Arbitration to the other party (same address as the Dispute Notice), or as otherwise agreed by the parties. b) Hearing Format. During the arbitration, the amount of any settlement offer made shall not be disclosed to the arbitrator until after the arbitrator determines the amount, if any, to which you or Epson is entitled. The discovery or exchange of non-privileged information relevant to the Dispute may be allowed during the arbitration. c) Arbitration Fees.
1.9 Severability. If any provision in this Section 1 is found to be unenforceable, that provision shall be severed with the remainder of this Agreement remaining in full force and effect. The foregoing shall not apply to the prohibition against class or representative actions as provided in Section 1.5. This means that if Section 1.5 is found to be unenforceable, the entire Section 1 (but only Section 1) shall be null and void.
designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.
