PowerLite® Home Cinema 5040UB/5040UBe User's Guide
Contents PowerLite Home Cinema 5040UB/5040UBe User's Guide ....................................................................... 9 Introduction to Your Projector ................................................................................................................. Projector Features.............................................................................................................................. Product Box Contents.....................................................................
Using the Projector on a Network ............................................................................................................ Wired Network Projection................................................................................................................... Connecting to a Wired Network ..................................................................................................... Selecting Wired Network Settings .................................................................
Projection Modes ............................................................................................................................... Changing the Projection Mode Using the Menus........................................................................... Image Aspect Ratio ............................................................................................................................ Changing the Image Aspect Ratio .......................................................................
Projector Setup Settings - Extended Menu....................................................................................... Projector Network Settings - Network Menu..................................................................................... Projector Information Display - Info Menu ........................................................................................ Event ID Code List............................................................................................................
Solutions When a WirelessHD Source Does Not Display Correctly............................................. 149 Solving Projector or Remote Control Operation Problems ............................................................... 150 Solutions to Projector Power or Shut-Off Problems ..................................................................... 150 Solutions to Problems with the Remote Control...........................................................................
PowerLite Home Cinema 5040UB/5040UBe User's Guide Welcome to the PowerLite Home Cinema 5040UB/5040UBe User's Guide. For a printable PDF copy of this guide, click here.
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual.
• 2.1× optical zoom ratio for improved zooming capability Product Box Contents Additional Components Optional Equipment and Replacement Parts Warranty and Registration Information Parent topic: Introduction to Your Projector Product Box Contents Save all the packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when shipping.
7 Terminal cover (PowerLite Home Cinema 5040UBe) The PowerLite Home Cinema 5040UBe also comes with the following parts: 1 WirelessHD Transmitter 2 AC adapter and cord Parent topic: Projector Features Additional Components Depending on how you plan to use the projector, you may need to obtain additional components. Note: To connect a Mac that does not include a compatible video output port, you need to obtain an adapter that allows you to connect to an input port on the projector.
Signal or connection type Additional component necessary MHL (PowerLite Home Cinema 5040UBe) MHL-compatible device or a device with one of the following: • MHL cable • HDMI cable with a MHL adapter compatible with your device • integrated MHL connector Note: The HDMI4 port on the WirelessHD transmitter supports MHL. 3D Compatible HDMI cable and active shutter 3D glasses Available for purchase from Epson or an authorized Epson reseller.
Option or part Part number Replacement air filter V13H134A39 RF 3D glasses (ELPGS03) V12H548006 Wireless LAN module (ELPAP10) V12H731P02 Projector ceiling mount CHF4000 Belkin PureAV HDMI audio video cable, 6 ft AV22300-06 Belkin PureAV HDMI audio video cable, 12 ft AV22300-12 Belkin PureAV HDMI audio video cable, 3 ft AV22300-03 Belkin Pro Series VGA/SVGA cable, 6 ft F3H982-06 Belkin Pro Series VGA/SVGA cable, 10 ft F3H982-10 Belkin Pro Series VGA/SVGA cable, 25 ft F3H982-25 In additi
• Notes contain important information about your projector. • Tips contain additional projection information. Parent topic: Introduction to Your Projector Where to Go for Additional Information Need quick help on using your projector? Here's where to look for help: • epson.com/support (U.S) or epson.ca/support (Canada) View FAQs (frequently asked questions) and e-mail your questions to Epson technical support 24 hours a day.
Projector software Manual Description Epson iProjection app Instructions are included with the app Lets you project from an iOS or Android device if your projector is connected to a network that includes a wireless access point. Visit epson.com/projectorapp (U.S.) or epson.ca/projectorapp (Canada) for more information.
Projector Parts - Front/Top 1 Lamp cover 2 Exhaust vent 3 Lens shutter 4 Lens 5 Air intake/air filter cover 6 Remote receivers 7 Control panel Parent topic: Projector Part Locations 17
Projector Parts - Rear 1 Security slot 2 AC input port 3 Remote receiver 4 Opt.HDMI (300mA) port (USB power for optical HDMI connections) 5 HDMI1 (HDCP 2.
Projector Parts - Base 1 Mounting bracket holes 2 Rear foot 3 Front adjustable feet Parent topic: Projector Part Locations 19
Projector Parts - Control Panel 1 Status light 2 Lamp light 3 Temp light 4 Menu button (accesses projector menu system) 5 OK button (selects options) 6 Control panel cover 7 Vertical keystone adjustment buttons (adjust screen shape) and arrow buttons 8 Arrow buttons 9 Esc button (cancels/exits functions) 10 Lens button (cycles through lens adjustment options) 20
11 Source button (cycles through the list of sources) 12 Power button/light Parent topic: Projector Part Locations Projector Parts - Remote Control 1 On button (turns on projector) 21
2 Home button (displays Home screen) 3 Source buttons (select specific video input sources) 4 Link Menu button (displays the main menu of the connected device) Control buttons (control playback and other features of connected devices that support the HDMI CEC standard) 5 HDMI Link button (displays the settings menu for HDMI Link) 6 Lens button (cycles through lens adjustment options) 7 Arrow buttons (move though on-screen options) 8 Default button (returns selected setting to default value) 9
Parent topic: Projector Part Locations Related references Remote Control Operation 23
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Projector Connections Installing Batteries in the Remote Control Projector Placement You can place the projector on almost any flat surface to project an image. You can also install the projector in a ceiling mount if you want to use it in a fixed location.
Front Rear Front Ceiling 25
Rear Ceiling Wherever you set up the projector, make sure to position it squarely in front of the center of the screen, not at an angle, if possible. If you project from the ceiling or from the rear, be sure to select the correct Projection option in the projector's menu system. Parent topic: Projector Placement Related references Projector Setup Settings - Extended Menu Projection Distance The distance at which you place the projector from the screen determines the approximate size of the image.
You can also use the projector Throw Distance Calculator at epson.com/support (U.S.) or epson.ca/support (Canada). 4:3 Aspect Ratio Image or Screen Screen or image size Projection distance (1) Offset from lens center Offset from lens center (2) (3) Wide to Tele 50 inches (127 cm) 72 to 151 inches 13.9 inches (35 cm) 43.9 inches (111 cm) 16.7 inches (42 cm) 52.7 inches (134 cm) 22.2 inches (56 cm) 70.2 inches (178 cm) 27.8 inches (71 cm) 87.8 inches (223 cm) 33.3 inches (854 cm) 105.
Screen or image size Projection distance (1) Offset from lens center Offset from lens center (2) (3) Wide to Tele 200 inches (508 cm) 291 to 610 inches 55.6 inches (141 cm) 175.6 inches (446 cm) 61.1 inches (155 cm) 193.1 inches (491 cm) 68 inches (173 cm) 214.8 inches (546 cm) (740 to 1548 cm) 220 inches (558.8 cm) 321 to 671 inches (814 to 1704 cm) 244.
Screen or image size Projection distance (1) Offset from lens center Offset from lens center (2) (3) Wide to Tele 300 inches (762 cm) 357 to 748 inches 68.1 inches (173 cm) 215.2 inches (547 cm) (908 to 1899 cm) Parent topic: Projector Placement Projector Connections See these sections to connect the projector to a variety of projection sources.
Using the gaps at the bottom of the terminal cover, pull the cover out and remove it. To reattach the cover, reverse the steps to remove it. Parent topic: Projector Connections Connecting to an HDMI Video Source If your video source has an HDMI port, you can connect it to the projector using an optional HDMI cable. The HDMI connection provides the best image quality. 1. Connect the HDMI cable to your video source's HDMI output port. 2. Connect the other end to one of the projector's HDMI ports.
Related tasks Attaching and Removing the Cable Clips Connecting to Computer Sources Follow the instructions in these sections to connect a computer to the projector. Connecting to a Computer for VGA Video Connecting to a Computer for HDMI Video Parent topic: Projector Connections Connecting to a Computer for VGA Video You can connect the projector to your computer using a VGA computer cable.
2. Connect the other end to one of the projector's HDMI ports. If you are connecting an optical HDMI cable, you must also connect the cable's USB power connector to the Opt.HDMI (300mA) port. Parent topic: Connecting to Computer Sources Related tasks Attaching and Removing the Cable Clips Attaching and Removing the Cable Clips You can install the cable clips that came with your projector to provide additional support to the HDMI cables. 1. Plug in the HDMI cables. 2.
connection provides the best image quality, if available). You can also connect speakers to any video source that has its own speaker connections. 1 Video source 2 Surround sound speakers 3 Receiver 4 Video cable Parent topic: Projector Connections Connecting to a Trigger Out Port You can connect your projector to external devices such as motorized screens that support a trigger signal. When active, a 12V signal is sent to the connected device while the projector is powered on. 1. Connect a 3.
3. Turn on the Trigger Out setting in the projector's Extended menu. Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Installing Batteries in the Remote Control The remote control uses the two AA batteries that came with the projector. Caution: Use only the type of batteries specified in this manual. Do not install batteries of different types, or mix new and old batteries. 1. Remove the battery cover.
2. Insert the batteries with the + and – ends facing as shown. 3. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wired Network Projection Wireless Network Projection Selecting External Network Detection Settings Wired Network Projection You can project through a wired network. To do this, you connect the projector to your network, and then set up your projector and computer for network projection.
Selecting Wired Network Settings Before you can project from computers, tablets, or smartphones over your network, you must select the network settings for the projector using its menu system. Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter.
5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen on a smartphone or tablet.
7. Select the Wired LAN menu and press Enter. 8. Select your IP Settings as necessary: • If your network assigns addresses automatically, turn on the DHCP setting. • If you must set addresses manually, turn off DHCP and enter the projector's IP Address, Subnet Mask, and Gateway Address as needed. Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on the remote control. To select a highlighted number, press Enter. Press Finish when you are done. 9.
After setting up the projector as described here, install the network software from the included CD or download the software and manuals as necessary. Note: If your projector is connected via a LAN cable to a network that includes a wireless access point, you can connect to the projector wirelessly through the access point using the Epson network software.
Selecting Wireless Network Settings Manually Before you can project from your wireless network, you must select the network settings for the projector using its menu system. 1. Turn on the projector. 2. Press the Menu button. 3. Select the Network menu and press Enter. 4. Make sure the Wireless LAN Power setting is set to On. 5. Select Network Configuration and press Enter.
6. Select the Basic menu and press Enter. 7. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network. • PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Remote Password lets you enter a password up to 8 alphanumeric characters long for accessing the Remote or Basic Control screen on a smartphone or tablet.
8. Select the Wireless LAN menu and press Enter. 9. Select the settings on the Wireless LAN menu as necessary for your network. 10. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Note: Check your network security settings after completing the wireless settings. After you complete the wireless settings for your projector, you need to select the wireless network on your computer, or iOS or Android device.
Wireless LAN Menu Settings Setting Options Description Connection Mode Quick Selects the type of wireless connection: Advanced Quick: lets you quickly connect to one computer Advanced: lets you connect to multiple computers via a wireless network access point (infrastructure mode) Channel 1ch In Quick connection mode, selects the frequency band (channel) used by the wireless LAN 6ch 11ch SSID Up 32 alphanumeric characters Sets the SSID (network name) of the wireless LAN system the projector is c
Related references Restricted IP Addresses Restricted IP Addresses When manually entering IP Settings, you cannot use these ranges of IP addresses: Setting Restricted IP addresses IP Address 0.0.0.0 127.x.x.x 224.0.0.0 to 255.255.255.255 Subnet Mask 0.0.0.0 255.255.255.255 Gateway Address 0.0.0.0 197.x.x.x 224.0.0.0 to 255.255.255.
2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Basic menu and press Enter. 5. Set the Display LAN Info setting to Text & QR Code. 6. Select Complete and follow the on-screen instructions to save your settings and exit the menus.
7. Press the LAN button on the remote control or select Display the QR Code in the projector's Network menu. (You can also press the Home button on the remote control and select Display the QR Code on the Home screen.) Your projector displays the QR code on the projection surface. Note: If you do not see the QR code after pressing the LAN button, press Enter to display it. 8. Start Epson iProjection on your mobile device. 9.
5. Select the Wireless LAN menu and press Enter. 6. Select Advanced as the Connection Mode setting and press Enter. 7. Select Search Access Point and press Enter. 8. Select the name of the wireless network you want to connect to and press Enter. 9. If the network has security enabled, enter the wireless password.
10. Select the settings on the Security menu as necessary for your network. 11. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Parent topic: Wireless Network Projection Selecting Wireless Network Settings in Windows Before connecting to the projector, select the correct wireless network on your computer. 1.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Security menu and press Enter. 6. Select the settings on the Security menu as necessary for your network. 7. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus.
Setting Options Description Passphrase — For the selected security, selects the pre-shared passphrase used on the network Parent topic: Enabling WPA or WPA2 Security Selecting External Network Detection Settings If you are using a compatible network control system, you can select settings that allow your projector to be detected by those systems. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4.
Parent topic: Using the Projector on a Network 52
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
2. Plug the power cord into an electrical outlet. Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. The projector's power light turns blue. This indicates that the projector is receiving power. 3. Press the power button on the projector or the On button on the remote control to turn on the projector. The shutter opens and the status light flashes blue as the projector warms up. Once the projector is warmed up, the status light stops flashing and turns blue.
2. Press the arrow buttons on the remote control or control panel to navigate the screen, and press Enter to select an option. 1 Select the video source you want to project 2 Display the QR code 3 Display the projector's menus 4 Select customizable menu options 5 Select to change the 3D settings 6 Select to change the Color Mode Note: You can select the customizable menu options using the Custom Function 1 and Custom Function 2 settings in the Extended menu. 3.
Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown. Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Note: When using the Blank feature, the projector lamp is still on. To turn off the lamp, turn off the projector. 1.
3. To transport or store the projector, make sure the status light is off, then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the status light is on or flashing. Parent topic: Using Basic Projector Features Related tasks Shutting Off the Picture Temporarily Transporting the Projector Viewing 3D Images You can view 3D images using your projector.
3. Begin playback from the video device. Note: Make sure you set the video device to play content in 3D mode. 4. Slide the power switch on the 3D glasses to the On position. 5. Put on the 3D glasses. If you do not see a 3D image, pair the glasses with the projector. Note: If you change the video source or you are not within range of your projector, the glasses enter standby mode and the status light flashes green.
4. Slide the power switch on the 3D glasses to the On position. 5. Move the glasses within 10 feet (3 m) of the projector and hold down the Pairing button for at least three seconds. The status light on the glasses flashes green and red. If pairing is successful, the light turns green for 10 seconds and then turns off. Parent topic: Viewing 3D Images Charging the 3D Glasses When the status light on the glasses flashes red to indicate a low battery, it is time to charge the glasses.
1. Connect the smaller end of the charging cable to the port on the bridge of the glasses. Note: Make sure you connect the cable in the correct orientation or you may damage the glasses or cable. 2. Do one of the following: • Plug the other end of the charging cable into a powered USB port on a computer or other device. • Plug the other end of the charging cable into a USB-to-AC adapter with the following specifications: Input: 100-240V, ~0.
3D Viewing Range When you view 3D images, make sure you are positioned within the viewing range shown here. 1 32 ft (10 m) Parent topic: Viewing 3D Images Selecting the Language for the Projector Menus If you want to view the projector's menus and messages in another language, you can change the Language setting. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Extended menu and press Enter. 4. Select the Language setting and press Enter. 5. Select the language you want to use and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Using Basic Projector Features Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. 1. Turn on the projector and display an image. 2.
3. To adjust the position of the projected image further, press the Lens button on the remote control or projector until Adjust Lens Shift appears on the screen. If the projected image is unevenly rectangular, you need to adjust the image shape.
4. Press the arrow buttons on the remote control or the control panel to adjust the position of the projected image as necessary. 1 Maximum horizontal range (H × 47%) 2 Maximum vertical range (V × 96%) 3 1/2 the vertical height of the image 4 1/2 the horizontal width of the image Note: You cannot move the image to both the horizontal and vertical maximum values. 5. When you are finished, press the Esc button on the control panel or remote control.
Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level. If you place the projector at an angle to the screen, or tilted up or down, or off to the side, you may need to correct the image shape for the best display quality.
1. Turn on the projector and display an image. 2. Press the Lens button on the control panel or remote control. 3. Press the Lens button repeatedly until Adjust Zoom is displayed on the screen. 4. Press and hold the left or right arrow button on the control panel or remote control to resize the image. 5. Press the Esc button on the control panel or remote control when finished.
Remote Control Operation The remote control lets you control the projector from almost anywhere in the room. You can point it at the screen, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the distance and angles listed here.
Horizontal 1 32 feet (10 m) 2 ± 30° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
3. Do one of the following: • Press the source button on the projector until you see the image from the source you want. • Press the button for the source you want on the remote control.
• Press the Home button on the remote control and select your image source. Parent topic: Using Basic Projector Features Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front (default setting) lets you project from a table in front of the screen. • Front/Ceiling flips the image over top-to-bottom to project upside-down from a ceiling or wall mount.
1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projection Modes Related concepts Projector Placement Image Aspect Ratio The projector can display images in different width-to-height ratios called aspect ratios.
Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. Note: For HDMI sources, the input signal determines the image's aspect ratio. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control. A list of the available aspect ratios appears. 3. To cycle through the available aspect ratios for your input signal, press the up or down arrow button. 4. Press Enter to select the aspect ratio.
Aspect ratio setting Description Full Displays images using the full width of the projection area, but does not maintain the aspect ratio. Note: When projecting a 4K signal, you can select only Normal as the aspect ratio setting. Parent topic: Image Aspect Ratio Color Mode The projector offers different Color Modes to provide optimum brightness, contrast, and color for a variety of viewing environments and image types.
4. To cycle through all the available Color Modes for your input signal, press the up or down arrow button. 5. Press Enter to select a Color Mode.
3. Select the Image menu and press Enter. 4. Select the Auto Iris setting and choose one of the following: • High Speed to adjust brightness as soon as the scene changes. • Normal for standard brightness adjustment. Note: You can set Auto Iris for each Color Mode that supports the feature. 5. Press Menu or Esc to exit the menus.
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments.
1. Turn on the projector and switch to the HDMI or WirelessHD image source you want to use. 2. Press the P-in-P button on the remote control. The second HDMI video source appears as a sub-screen in the corner of the image. Note: While Picture in Picture mode is active, press the Menu button on the remote control to adjust the size and position of the sub-screen. 3. To swap the main screen and sub-screen video sources, press and hold the P-in-P button for at least three seconds. 4.
Adjusting the Color Convergence (Panel Alignment) You can use the Panel Alignment feature to manually adjust the color convergence (the alignment of the red, green and blue colors) in the projected image. Note: Allow your projector to warm up for at least 10 to 15 minutes and make sure the image is in focus before you use the Panel Alignment feature.
• B to adjust the blue color convergence. Note: You can only adjust the red or blue color convergence. Green is the standard color panel and cannot be adjusted. 8. Select the Pattern Color setting and press Enter. 9. Select the pattern you want to use and press Enter. 10. Select Start Adjustments and press Enter. You see this screen: 11. Press Enter.
12. Use the arrow buttons on the remote control to adjust the color alignment of the color you selected for the Select Color setting. Note: Your adjustments affect the gridlines in the entire screen. You can fine-tune your adjustments by continuing with the next steps. 13. When you are finished adjusting the screen, press Enter. You see this screen: 14. Select Adjust the four corners and press Enter. 15.
You see this screen: 18. Do one of the following: • If your projector's panel alignment is now correct, select Exit and press Enter to return to the Panel Alignment menu. • If your projector needs additional panel alignment, select Select intersection and adjust and press Enter. Use the arrow keys on the remote control to highlight the corner of any box on the screen that is misaligned and press Enter to adjust the color convergence. Repeat this step as necessary.
2. Select the Extended menu and press Enter. 3. Select the Display setting and press Enter. 4. Select the Color Uniformity setting and press Enter. 5. Press Enter and select On. 6. Press Esc. 7. Select the Adjustment Level setting and press Enter. 8. Press the right and left arrow buttons to adjust the level, then press Esc. 9. Select the Start Adjustments setting and press Enter.
10. Select the area of the screen that you want to adjust and press Enter. 11. Select the color (Red, Green, or Blue) you want to adjust, and use the left arrow button to weaken the color tone and the right arrow button to strengthen the color tone. 12. Press Esc. 13. Repeat steps 10 and 11 for each area you want to adjust. 14. When you are finished, press the Menu button.
2. Select the Settings menu and press Enter. 3. Select the Lock Setting setting and press Enter. 4. Select one of these lock types and press Enter: • To lock the zoom, focus, and lens shift settings, select Lens Lock. • To lock the projector's power button, select Child Lock. To turn the projector on, you must press the power button for longer than three seconds. Note: Child Lock does not prevent the projector from turning on when the power cord is connected if the Direct Power On Setting is set to On.
Parent topic: Projector Security Features Related references Projector Feature Settings - Settings Menu Unlocking the Projector's Buttons If the projector's buttons have been locked, hold the OK button on the projector's control panel for seven seconds to unlock them. Parent topic: Locking the Projector's Lens Settings and Buttons Installing a Security Cable You can use the security slot on the back of the projector to attach a Kensington lock.
You see this screen: 5. Select one of the following options: • Load Memory: Overwrites your current settings with saved settings • Save Memory: Saves your current settings to memory (10 memories with different names are available) Note: A memory name that has already been used is indicated by a blue mark. Saving over a previously saved memory overwrites the settings with your current settings. • Erase Memory: Erases the selected memory settings • Rename Memory: Renames a saved memory 6. Press Esc to exit.
3. Press the Menu button. Note: You can also press the Memory button on the remote control to access the Memory menu directly. 4. Select the Settings menu and press Enter. 5. Select the Memory setting and press Enter. You see this screen: 6. Select one of the following options: • Load Lens Position: Overwrites your current focus, zoom, and lens shift settings with saved settings Note: You can load the saved settings from Memory1 or Memory2 by pressing the Lens1 or Lens2 buttons on the remote control.
• Rename Lens Position: Renames a saved lens position (12 characters maximum) 7. Press Esc to exit.
Using WirelessHD You can use the included WirelessHD transmitter to wirelessly stream HD content from a video device to the projector (PowerLite Home Cinema 5040UBe).
4 Power switch (turns the transmitter on or off) 5 On/Standby light (flashes when starting up; lit when the transmitter is on) 6 WiHD light (lit when sending a wireless signal to the projector) 7 Link light (lit when connected to the projector; flashing when searching for the projector or when on standby) 8 TV light (lit when the HDMI Out port is selected as the output) 9 1-4 (HDMI1 through HDMI4) lights (lit when the port is being projected) Back 1 AC input port (connects the AC adapter) 2
WirelessHD Transmission Range Place the WirelessHD Transmitter within the distance and angles shown here. Make sure the front of the WirelessHD Transmitter faces the front of the projector. Place the WirelessHD transmitter on a wooden shelf or other location that does not block the signal.
Horizontal 1 16 feet (5 m) 2 32 feet (10 m) 3 70° 4 45° When positioning the WirelessHD transmitter, note the following: • The wireless transmission range varies depending on the placement and material of the furniture and walls. The values provided here are for your reference only. • The projector cannot communicate through walls. • When checking the signal, place the projector and WirelessHD Transmitter close to each other and make sure there are no other projectors operating nearby.
WirelessHD Remote Control Operation The remote control lets you control the WirelessHD transmitter from almost anywhere in the room. Make sure that you aim the remote control at the WirelessHD transmitter's remote receiver within the distance and angles shown here. Vertical 1 13 feet (4 m) 2 65.6 feet (20 m) 3 ± 40° Horizontal 1 13 feet (4 m) 2 65.
3 ± 40° Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries. Parent topic: Using WirelessHD Connecting the WirelessHD Transmitter You can connect up to four HDMI input sources and one HDMI output source to your WirelessHD transmitter. 1.
Note: You can connect an MHL-compatible smartphone or tablet to the HDMI4 port on the WirelessHD Transmitter. 3. To use the WirelessHD transmitter as a pass-through device to a television or other display, connect an HDMI cable to the display device and to the HDMI Out port on the back of the transmitter. Parent topic: Using WirelessHD Viewing WirelessHD Content You can project content wirelessly from any device connected to the WirelessHD transmitter. 1.
The WiHD light on the transmitter turns on and your projector displays content wirelessly. Note: If the WirelessHD connection fails, press the Setup button on the bottom of the WirelessHD transmitter and try again. Parent topic: Using WirelessHD Switching WirelessHD Sources If you have connected multiple HDMI input sources to your WirelessHD transmitter, you can use the projector remote control to switch between sources. 1. Aim the remote control at the WirelessHD transmitter.
2. Press the Input button on the remote control or the WirelessHD transmitter repeatedly to select the input source you want. After a few seconds, the display switches to the selected source.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
You see the menu screen displaying the Image menu settings. 2. Press the up or down arrow button to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter or OK. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6.
Note: The available settings depend on the currently selected input source. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Color Temp. (color temperature) Color Temp. Skin Tone Customized Description Color Temp.
Setting Options Description Image Enhancement 4K Enhancement 4K Enhancement: accepts 4K signals and enhances the output of 1080p signals Image Preset Mode Noise Reduction MPEG Noise Reduction Super-resolution Detail Enhancement Image Preset Mode: selects one of five preset groups of settings for the next image enhancement options Noise Reduction: reduces flickering in analog images MPEG Noise Reduction: reduces the noise or artifacts seen in MPEG video Super-resolution: sharpens blurred images result
Setting Options Description Advanced Gamma Selects various detailed color settings RGBCMY Gamma: adjusts the gamma levels of the image. Select EPSON Super White Customized to adjust the Lens Iris (PowerLite Pro Cinema gamma while viewing the image or a graph.
Setting Options Description Power Consumption High Selects the brightness mode of the projector lamp Medium High: sets maximum lamp brightness ECO Medium: reduces the brightness of the lamp ECO: reduces lamp brightness and fan noise, and saves power and lamp life Auto Iris Off Normal High Speed Adjusts the projected luminance based on the image brightness when certain Color Modes are selected Note: The Brightness setting does not affect lamp brightness.
Note: The available settings depend on the currently selected input source. You cannot change the Signal menu settings when the LAN source is selected. To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description 3D Setup 3D Display Selects various 3D options 3D Format 3D Display: enables 3D mode 2D-to-3D Conversion 3D Format: selects the 3D format 3D Depth Diagonal Screen Size 3D Brightness Inverse 3D Glasses 3D Viewing Notice 2D-to-3D Conversion: converts 2D images to 3D 3D Depth: sets the depth for the 3D image Diagonal Screen Size: selects the actual size of the screen to maximize the 3D effect 3D Brightness: adjusts the brightness of the 3D image Inverse 3D Glasses: revers
Setting Options Description Auto Setup On Automatically optimizes computer image quality Off Overscan Auto Changes the projected image ratio to make the edges visible by a selectable percentage or automatically Off 4% 8% Blanking Various settings Covers part of the image with a black screen to hide raster lines at the edge of the screen. Note: Using this feature reduces the image size.
• The Aspect setting is not available for HD video signals. Parent topic: Adjusting the Menu Settings Related concepts Image Aspect Ratio Related tasks Viewing 3D Images Projector Feature Settings - Settings Menu Options on the Settings menu let you customize various projector features.
PowerLite Home Cinema 5040UBe: Setting Options Description Keystone Varying levels available Adjusts image shape to rectangular (vertically) Picture in Picture See the list of available Picture in Adjusts the size and location of Picture options the sub-screen, swaps sources and exits Picture in Picture mode 109
Setting Options Description HDMI Link Device Connections Adjusts the HDMI Link options that allow the projector remote to control HDMI-connected devices that support the CEC standard HDMI Link Audio Out Device (PowerLite Home Cinema 5040UBe) Power On Link Power Off Link Link Buffer Device Connections: lists the devices connected to the HDMI1 and HDMI2 ports HDMI Link: enables or disables the HDMI Link function Audio Out Device: selects which port on the WirelessHD Transmitter outputs audio Power On L
Setting Options Description WirelessHD Connected Device (PowerLite Home Cinema 5040UBe) WirelessHD Adjusts settings for use with the WirelessHD transmitter Video Reception Reset Connected Device: displays a list of available WirelessHD devices WirelessHD: controls whether the projector receives WirelessHD signals Video Reception: displays the strength of the WirelessHD signal Reset: resets the WirelessHD settings to their defaults.
Setting Options Description Memory Load Memory Controls the saved projector settings and lens positions Save Memory Erase Memory Rename Memory Load Lens Position Save Lens Position Erase Lens Position Rename Lens Position Load Memory: displays the list of customized settings entries that you have created Save Memory: saves the current projector settings to the projector's memory Erase Memory: displays the list of customized settings entries that you have created Rename Memory: displays the list of cu
Projector Setup Settings - Extended Menu Settings on the Extended menu let you customize various projector setup features that control its operation. Setting Options Description Home Screen Home Screen Auto Disp. Adjust settings on the Home Screen Custom Function 1 Custom Function 2 Home Screen Auto Disp.
Setting Options Description Projection Front Selects the way the projector faces the screen so the image is oriented correctly Front/Ceiling Rear Rear/Ceiling Operation — See the Operation settings table in this topic Standby Mode Communication Off Indicates whether the projector can be monitored over a network while in standby mode Communication On Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option) Display settings
Setting Description Direct Power On Turns on the projector when you plug it in Sleep Mode Automatically places the projector in standby mode after an interval of inactivity Sleep Mode Timer Sets the time before the projector automatically turns off (Sleep Mode must be turned on) Illumination Turns off the lights on the projector Trigger Out Outputs a DC 12V signal from the 3.
Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network. Setting Options Description Wireless LAN Power On Enable or disable wireless communication Off Net. Info - Wireless LAN Connection mode Wireless LAN Sys.
Setting Options Description Net. Info - Wired LAN Projector Name Displays wired network status and details DHCP IP Address Subnet Mask Gateway Address MAC Address Display the QR Code — Displays the QR Code Network Configuration Accesses additional network menus Configures your network settings Parent topic: Adjusting the Menu Settings Projector Information Display - Info Menu You can display information about the projector and input sources by viewing the Info menu.
Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Event ID code Cause and solution 0022 Unstable network communication. Check the network communication status, wait a few moments, and try connecting to the network again. 0027 0028 0029 0030 0031 0035 0434 0482 0484 0485 0432 Turn the projector off and then on again. 0435 0433 Cannot display the transferred images. Restart the network software. 0484 Communication with computer was disconnected. Restart the network software. 04FE The network software quit unexpectedly.
Event ID code Cause and solution 0020 Communication error. Turn the projector off and then on again. 0026 0032 0036 0037 0038 0899 Parent topic: Projector Information Display - Info Menu Projector Reset Options - Reset Menu You can reset most of the projector settings to their default values using the Reset All Config option on the Reset menu.
You cannot reset the following settings using the Reset All Config option: • Language • Lamp Hours • Memory settings • All settings in the Network menu • Panel Alignment • Color Uniformity Parent topic: Adjusting the Menu Settings 121
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove dust or smudges, gently move the shutter to the side and wipe the lens with lens-cleaning paper. After cleaning, close the shutter. • To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the lens. Do not spray any liquid directly on the lens. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire.
Note: Unplug any charging cables from the glasses before cleaning them. Caution: Do not use paper towels or any other abrasive materials to clean the glasses. Parent topic: Projector Maintenance Air Filter and Vent Maintenance Regular filter maintenance is important to maintaining your projector. Your Epson projector is designed with an easily accessible, user-replaceable filter to protect your projector and make regular maintenance simple. Filter maintenance intervals will depend on the environment.
• You see a message telling you to clean it. 1. Turn off the projector and unplug the power cord. 2. Press and hold the tab on the air filter cover, and pull to remove the cover. 3. Pull the air filter out of the projector.
4. Tap each side of the air filter 4 to 5 times to shake off any excess dust. Do this outside the room or away from the projector. Caution: Do not use excessive force when tapping the air filter, or it may crack and become unusable. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Do not use canned air; the gases may leave a residue, or push dust and debris into the projector's optics or other sensitive areas. 5.
6. Place the air filter back in the projector as shown. 7. Attach the air filter cover as shown. Parent topic: Air Filter and Vent Maintenance Related tasks Replacing the Air Filter Replacing the Air Filter You need to replace the air filter in the following situations: • After cleaning the air filter, you see a message telling you to clean or replace it • The air filter is torn or damaged You can replace the air filter while the projector is mounted to the ceiling or placed on a table. 1.
2. Press and hold the tab on the air filter cover, and pull to remove the cover. 3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown. 5. Attach the air filter cover as shown. Parent topic: Air Filter and Vent Maintenance Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
Parent topic: Projector Maintenance Related references Projector Information Display - Info Menu Optional Equipment and Replacement Parts Projector Lamp Specifications Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot. Warning: Let the lamp fully cool before replacing it to avoid injury. You can replace the lamp while the projector is mounted to the ceiling, if necessary. 1. Turn off the projector and unplug the power cord. 2.
4. Slide the lamp cover out and lift it off. 5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 6. Lift up the lamp handle and gently pull the lamp out of the projector.
Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp into the projector. If it does not fit easily, make sure it is facing the right way. Lower the handle. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 8. Push in the lamp firmly and tighten the screws to secure it. Caution: Do not over-tighten the screws.
9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp's usage. Parent topic: Projector Lamp Maintenance Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
2. Press the Menu button. 3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter. You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual.
1. Remove the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Replace the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Related references Remote Control Specifications Transporting the Projector The projector contains precision parts, some of which are glass.
Parent topic: Maintaining and Transporting the Projector Related tasks Turning Off the Projector 137
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Solving Image Problems Solving Projector or Remote Control Operation Problems Solutions When Wireless Authentication Fails Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
Projector Light Status The lights on the projector indicate the projector status and let you know when a problem occurs. Check the status and color of the lights and look for a solution in the table here.
Power light Status light Lamp light Temp light Status and solution Blue Flashing blue Off Warming up; wait for an image to appear Off Shutting down; when the status light stops flashing, you can unplug the projector Off Off Off Off Standby or sleep mode Blue Varies Off Flashing orange Projector is too hot • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects • Clean or replace the air filter • Make sure the environmental temperature is not too
Power light Status light Lamp light Temp light Status and solution Off Flashing blue Orange Lamp has a problem Off • Check the Lamp Hours in the Info menu to see if the lamp is burned out.
Parent topic: Solving Problems Related references Projector Setup Settings - Extended Menu Related tasks Cleaning the Air Filter Replacing the Lamp Replacing the Air Filter Solving Image Problems Check the solutions in these sections if you have any problems with projected images.
• Check the settings on the Signal menu to make sure they are correct for the current video source. • Adjust the Brightness setting or select the Normal Power Consumption setting. • Check the Display setting to make sure Messages is set to On. • If the projector does not respond when you press the control panel buttons, the buttons may be locked. Unlock the buttons. • For images projected with Windows Media Center, reduce the screen size from full screen mode.
Displaying From a PC Laptop Displaying From a Mac Laptop Parent topic: Solving Image Problems Related concepts Projector Connections Displaying From a PC Laptop If you see the "No Signal" message when you display from a PC laptop, you need to set up the laptop to display on an external monitor. 1. Hold down the laptop's Fn key and press the key labeled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear. 2.
• Check the input resolution under Projector Info in the Info menu and make sure that the projector supports that resolution.
• If you adjusted the projector height using the projector feet, press the keystone buttons on the projector to adjust the image shape. • Adjust the image shape using the Keystone menu setting.
Supported Video Display Formats Solutions When the Image is Fuzzy or Blurry If the projected image is fuzzy or blurry, try the following solutions: • Adjust the image focus. • Clean the projector lens. • Check the lens for condensation. Note: To avoid condensation on the lens after bringing the projector in from a cold environment, let the projector warm up to room temperature before using it. • Position the projector close enough to the screen, and directly in front of it.
• Adjust the available settings on the Image menu for the current input source, such as Brightness, Contrast, Tint, Advanced, and Color Saturation. • Turn off the HDR mode in the Dynamic Range setting or set the Color Space setting to BT.709. • Make sure all the cables are securely connected to the projector and your video device. If you connected long cables, try connecting shorter cables. • Position the projector close enough to the screen.
• If the other solutions do not solve the problem, change the Inverse 3D Glasses setting on the Signal menu. Return the setting to its original value if changing it does not solve the problem as it can adversely affect the 3D image.
Projector Feature Settings - Settings Menu Related tasks Connecting the WirelessHD Transmitter Switching WirelessHD Sources Solving Projector or Remote Control Operation Problems Check the solutions in these sections if you have problems operating the projector or remote control.
Related references Where to Get Help Projector Light Status Projector Feature Settings - Settings Menu Related tasks Replacing the Remote Control Batteries Unlocking the Projector's Buttons Solutions to Problems with the Remote Control If the projector does not respond to remote control commands, try the following solutions: • Check that the remote control batteries are installed correctly and have power. If necessary, replace the batteries.
Related tasks Replacing the Remote Control Batteries Solutions to Password Problems If you cannot enter or remember a password, try the following solutions: • You may have turned on password protection without first setting a password. Try entering 0000 using the remote control. • If you have entered an incorrect password too many times and see a message displaying a request code, write down the code and contact Epson. Do not attempt to enter the password again.
Solutions When Using HDMI Link If you cannot control an HDMI device using the HDMI Link buttons, try the following solutions: • Make sure all necessary cables are securely connected and the power is on for the projector and connected video sources. • Make sure the cables meet the HDMI standards. • Make sure the connected device supports the CEC standards. • If you connected a new device or changed any connections, you may need to restart the device.
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661. This service is available for the duration of your warranty period. You may also speak with a projector support specialist by dialing (562) 276-4394 (U.S.) or (905) 709-3839 (Canada). Support hours are 6 AM to 8 PM, Pacific Time, Monday through Friday and 7 AM to 4 PM, Pacific Time, Saturday. Days and hours of support are subject to change without notice. Toll or long distance charges may apply.
Technical Specifications These sections list the technical specifications of your projector. General Projector Specifications Projector Lamp Specifications Remote Control Specifications Projector Dimension Specifications Projector Electrical Specifications Projector Environmental Specifications Projector Safety and Approvals Specifications Supported Video Display Formats General Projector Specifications Type of display Poly-silicon TFT active matrix Resolution 1920 × 1080 pixels (1080p) Lens F=2.
Projection distance 58.3 inches (1.48 m) to 747.6 inches (18.99 m) (in native aspect ratio) Projection methods Front, rear, ceiling-mounted Optical aspect ratio 16:9 (width-to-height) Focus adjustment Powered Zoom adjustment Optical, powered Zoom ratio 1 to 2.1 (Tele-to-Wide) Noise level 31 dB (High Power Consumption mode) 20 dB (ECO Power Consumption mode) Keystone correction angle ± 30º vertical USB Type B port compatibility USB 1.1 and 2.
Note: Turn off this product when not in use to prolong the life of the projector. Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Parent topic: Technical Specifications Remote Control Specifications Reception range 32 feet (10 m) Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 17.7 inches (450 mm) Width 20.5 inches (520 mm) Depth 6.
Power consumption Operating: (100 to 120 V) High Power Consumption mode: 373 W ECO Power Consumption mode: 283 W Standby: 0.27 W (Communication Off), 2.3 W (Communication On) Power consumption Operating: (220 to 240 V) High Power Consumption mode: 355 W ECO Power Consumption mode: 271 W Standby: 0.35 W (Communication Off), 2.
Canada ICES-003 Class B CSA C22.2 No. 60950-1-07 (cTUVus Mark) Parent topic: Technical Specifications Supported Video Display Formats For best results, your computer's monitor port or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically.
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (1080p) 24/30/50/60 1920 × 1080 4K × 2K 24/30/50/60 3840 × 2160 24/50/60 4096 × 2160 WirelessHD Input Signal 1, 2 (PowerLite Home Cinema 5040UBe) SDTV (480i/480p) 60 720 × 480 SDTV (576i/576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 HDTV (1080p) 24/30 1920 × 1080 4K × 2K 24/30/50/60 3840 × 2160 50/60 4096 × 2160 24 4096 × 2160 4K × 2K (SMPTE) WirelessHD Input Signal MHL3, 4 (
3 HDMI4 port only 4 When projecting in WirelessHD, this signal is not supported: 4K × 2K (SMPTE) 24 Hz HDMI 3D Signals Display format Refresh rate (in Hz) Resolution (in pixels) 3D formats HDTV (720p) 50/60 1280 × 720 Frame Packing Side by Side Top and Bottom HDTV (1080i) 50/60 1920 × 1080 Side by Side HDTV (1080p) 50/60 1920 × 1080 Side by Side 24 1920 × 1080 Frame Packing Side by Side Top and Bottom MHL 3D Signals (via WirelessHD Transmitter) (PowerLite Home Cinema 5040UBe) Display
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) FCC Compliance Statement Open Source Software License Trademarks Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to this site for information on how to return your products for proper disposal.
• Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 3° forward or back. • If the projector is mounted on a ceiling or wall, it should be installed by qualified technicians using mounting hardware designed for use with this projector. • When installing or adjusting a ceiling or wall mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants.
• You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. Do not use canned air, or the gases may leave a residue. • Do not store the projector outdoors for an extended length of time. • Except as specifically explained in this manual, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.
• Do not place anything that can become warped or damaged by heat near the exhaust vents. Do not bring your hands or face close to the vents while projection is in progress. Do not bring your face close to the projector while it is in use. • Before you move the projector, make sure its power is turned off, the plug is disconnected from the outlet, and all cables are disconnected. • Do not disassemble the lamp or subject it to impacts.
medical equipment related to direct medical care, please make your own judgment on this product's suitability after a full evaluation. Parent topic: Important Safety Instructions List of Safety Symbols (corresponding to IEC60950-1 A2) The following table lists the meaning of the safety symbols labeled on the equipment. No. 1 2 3 4 Symbol Approved Standards Description IEC60417 "ON" (power) No.5007 To indicate connection to the mains. IEC60417 "OFF" (power) No.
No. 7 8 9 10 11 12 Symbol Approved Standards Description IEC60417 For indoor use only No.5957 To identify electrical equipment designed primarily for indoor use. IEC60417 Polarity of DC power connector No.5926 To identify the positive and negative connections (the polarity) on a piece of equipment to which a DC power supply may be connected. IEC60417 Battery, general No.5001B On battery powered equipment.
No. 13 14 15 16 Symbol Approved Standards Description IEC60417 Alternating current No.5032 To indicate on the rating plate that the equipment is suitable for alternating current only; to identify relevant terminals. IEC60417 Direct current No.5031 To indicate on the rating plate that the equipment is suitable for direct current only; to identify relevant terminals. IEC60417 Class II equipment No.
No. Symbol 21 Approved Standards Description ISO 3864 Disassembly prohibition To indicate a risk of injury, such as electric shock, if the equipment is disassembled. 22 — Never look into the lens while the LED for lighting is on. 23 IEC60417 Standby, partial standby No. 5266 To indicate that part of the equipment is in the ready status. ISO3864 Caution, movable parts IEC60417 To indicate that you must keep away from movable parts according to protection standards. 24 No.
WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces.
• EPSON original drivers • Stonestreet One Drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/. GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone's free use or not licensed at all. The precise terms and conditions for copying, distribution and modification follow. GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License.
normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works.
the source code, even though third parties are not compelled to copy the source along with the object code. 4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 9.
How to Apply These Terms to Your New Programs If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program.
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Lesser General Public License instead of this License. GNU LGPL This projector product includes the open source software programs which apply the GNU Lesser General Public License Version 2 or later version ("LGPL Programs").
Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term "modification".) "Source code" for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.
the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.) Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6.
to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16.
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker. , 1 April 1990 Ty Coon, President of Vice That's all there is to it! libjpeg This projector product includes the open source software program "libjpeg" which applies the terms and conditions provided by owner of the copyright to the "libjpeg".
This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.
simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the resulting GIF files are larger than usual, but are readable by all standard GIF decoders. We are required to state that "The Graphics Interchange Format(c) is the Copyright property of CompuServe Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated.
library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user. libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c) 1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of Contributing Authors: Tom Lane Glenn Randers-Pehrson Willem van Schaik libpng versions 0.89, June 1996, through 0.
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions: 1. The origin of this source code must not be misrepresented. 2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source. 3. This Copyright notice may not be removed or altered from any source or altered source distribution. The Contributing Authors and Group 42, Inc.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions: 1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. 2.
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document. "Licensor" shall mean the copyright owner or entity authorized by the copyright owner that is granting the License. "Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity.
2. Grant of Copyright License. Subject to the terms and conditions of this License, each Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-charge, royalty-free, irrevocable copyright license to reproduce, prepare Derivative Works of, publicly display, publicly perform, sublicense, and distribute the Work and such Derivative Works in Source or Object form. 3. Grant of Patent License.
5. Submission of Contributions. Unless You explicitly state otherwise, any Contribution intentionally submitted for inclusion in the Work by You to the Licensor shall be under the terms and conditions of this License, without any additional terms or conditions. Notwithstanding the above, nothing herein shall supersede or modify the terms of any separate license agreement you may have executed with Licensor regarding such Contributions. 6. Trademarks.
Copyright [yyyy] [name of copyright owner] Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
newlib This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib". The "newlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of newlib programs • newlib 1.17.0 License terms of conditions of each program which are provided by owner of the copyright to the "newlib" are as follows.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
(4) Advanced Micro Devices Copyright 1989, 1990 Advanced Micro Devices, Inc. This software is the property of Advanced Micro Devices, Inc (AMD) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by AMD. AMD MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE.
To anyone who acknowledges that this file is provided "AS IS" without any express or implied warranty: permission to use, copy, modify, and distribute this file for any purpose is hereby granted without fee, provided that the above copyright notice and this notice appears in all copies, and that the name of Hewlett-Packard Company not be used in advertising or publicity pertaining to distribution of the software without specific, written prior permission.
Copyright 2002 SuperH, Inc. All rights reserved This software is the property of SuperH, Inc (SuperH) which specifically grants the user the right to modify, use and distribute this software provided this notice is not removed or altered. All other rights are reserved by SuperH. SUPERH MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS SOFTWARE.
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (14) Alexey Zelkin Copyright (c) 2000, 2001 Alexey Zelkin All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
ANY KIND CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS FITNESS FOR ANY PARTICULAR PURPOSE. (18) Citrus Project Copyright (c)1999 Citrus Project, All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Copyright (c) 2001 Mike Barcroft All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. iconv (Charset Conversion Library) v2.0 (28) Artem Bityuckiy (--enable-newlib-iconv) Copyright (c) 2003, Artem B. Bityuckiy, SoftMine Corporation. Rights transferred to Franklin Electronic Publishers. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3.
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (37) MIPS Technologies, Inc /* * Copyright (c) 2009 MIPS Technologies, Inc. * All rights reserved.
List of MIT License programs • jquery-1.11.2 • jquery-mobile-1.4.5 License terms of conditions of each program which are provided by owner of the copyright to the "MIT License" are as follows. Copyright (c) 2012 jQuery Foundation and other contributors, http://jquery.
Copyright (C) 2000-2003 by Embedded and Real-Time Systems Laboratory Toyohashi Univ. of Technology, JAPAN Copyright (C) 2004 by Embedded and Real-Time Systems Laboratory Graduate School of Information Science, Nagoya Univ., JAPAN.
The "TINET" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of TINET programs • tinet-1.4.4 License terms of conditions of each program which are provided by owner of the copyright to the "TINET" are as follows. (1) FreeBSD Copyright (c) 1980, 1986, 1993 The Regents of the University of California. All rights reserved.
Copyright (C) 2001-2006 by Dep.
All Rights Reserved. This program is licensed under the BSD license (the one with advertisement clause removed). If you are submitting changes to the project, please see CONTRIBUTIONS file for more instructions. License ----------This software may be distributed, used, and modified under the terms of BSD license: Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
Copyright (c) 2004, Jan Kneschke, incremental All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: - Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
Release 8 of PCRE is distributed under the terms of the "BSD" licence, as specified below. The documentation for PCRE, supplied in the "doc" directory, is distributed under the same terms as the software itself. The basic library functions are written in C and are freestanding. Also included in the distribution is a set of C++ wrapper functions, and a just-in-time compiler that can be used to optimize pattern matching. These are both optional features that can be omitted when the library is built.
THE C++ WRAPPER FUNCTIONS ----------Contributed by: Google Inc. Copyright (c) 2007-2012, Google Inc. All rights reserved. THE "BSD" LICENCE ----------Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: * Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
List of FastCGI programs • fcgi-2.4.0 License terms of conditions of each program which are provided by owner of the copyright to the "FastCGI" are as follows. This FastCGI application library source and object code (the "Software") and its documentation (the "Documentation") are copyrighted by Open Market, Inc ("Open Market"). The following terms apply to all files associated with the Software and Documentation unless explicitly disclaimed in individual files.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. Parent topic: Notices Copyright Notice All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation.
Copyright Attribution © 2016 Epson America, Inc.
PowerLite® Home Cinema 5040UB/5040UBe WirelessHD™ Transmitter (PowerLite Home Cinema 5040UBe only) Quick Setup Follow these steps to set up the included WirelessHD Transmitter. Before using the projector, make sure you read the safety instructions in the online User’s Guide. Choose a location Keep the projector level and place it at a height so its lens is even with the top or bottom of the screen and is centered horizontally.
Turn on your equipment Using the remote control 1 2 Install the batteries as shown (two AA batteries). Turn on your video source. Plug in the projector. Turn projector on 3 Choose which source to display Press the power button on the projector or the On button on the power light flashes blue, remote control. The shutter opens and the then stays on.
4 Press the Lens button on the remote control again and use the buttons to reduce or enlarge the image. and 5 Press the Lens button on the remote control again and use the , and buttons to reposition the image. , Note: If the glasses don’t automatically display 3D content, you may need to pair them with the projector. Move the glasses within 10 feet (3 m) of the projector, then press and hold the Pairing button on the 3D glasses for at least 3 seconds.
Troubleshooting Where to get help If you see a blank screen or the No signal message after turning on your video device or computer, check the following: Manuals • • Make sure the • If you’re using a Windows® laptop, press the function key on your keyboard that lets you display on an external monitor. It may be labeled . You may have to hold down the CRT/LCD or have an icon such as Fn key while pressing it (such as Fn + F7). Wait a moment for the display to appear.
Declaration of Conformity We: Located at: Telephone: Epson America, Inc. 3840 Kilroy Airport Way, MS 3-13, Long Beach, CA 90806 (562) 981-3840 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards.
This transmitter must not be co-located or used in conjunction with any other antenna or transmitter. Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated with minimum distance of at least 7.9 inches (20 cm) between the radiator and your body.
Epson America, Inc. Limited Warranty Two-Year Projector Limited Warranty and 90-Day Lamp Limited Warranty What Is Covered: Epson America, Inc. (“Epson”) warrants to the original retail purchaser of the Epson projector product enclosed with this limited warranty statement that the product, if purchased new and operated in the United States, Canada, or Puerto Rico will be free from defects in workmanship and materials for a period of two (2) years from the date of original purchase.
Remedies: Your exclusive remedy and Epson’s entire liability for a material breach of this Agreement will be limited to a refund of the price paid for the Epson products covered by this Agreement. Any action for breach of warranty must be brought within 3 months of the expiration date of the warranty. Epson is not liable for performance delays or for nonperformance due to causes beyond its reasonable control.
