English Peeler Model User’s Manual M00075901EN
English All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein.
English Safety Precautions This section presents important information intended to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location. Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. WARNING: Warnings must be followed carefully to avoid serious bodily injury.
English CAUTION: Do not connect cables in ways other than those mentioned in this manual. Different connections may cause equipment damage and burning. Be sure to set this equipment on a firm, stable, horizontal surface. The product may break or cause injury if it falls. Do not use in locations subject to high humidity or dust levels. Excessive humidity and dust may cause equipment damage or fire. Do not place heavy objects on top of this product. Never stand or lean on this product.
English Unpacking The following items are included for the standard specification printer. If any items are damaged, contact your dealer. ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ ❏ Printer Label roll paper Power switch cover Roll paper spacer Screw for installation of roll paper spacer Cover operation label Wire saddle Start Here Manual CD AC adapter* AC cable* * May not be included depending on the printer model.
English Downloading Drivers, Utilities, and Manuals Drivers, utilities, and manuals can be downloaded from one of the following URLs. For customers in North America, go to the following web site: http://www.epsonexpert.com/ For customers in other countries, go to the following web site: https://download.epson-biz.
English Power Switch Use the power switch on the top left of the printer to turn the printer on and off. Power Switch Cover You can use the enclosed power switch cover to make sure that the power switch is not accidentally pressed. Peel off the backing tape and press the cover into place to install it. You can turn the power switch on and off by inserting a pointed object such as a ballpoint pen in the holes in the power switch cover.
English Installing the Printer You must install this printer vertically (with the paper exit at the front). If the paper exit is blocked by label backing paper accumulating on a table or other surface, a paper jam or other problem may occur. Install the printer in a location, such as at the edge of a counter, where the backing paper will not accumulate near the paper exit. CAUTION: Never install the printer in locations that receive direct sunlight.
English Changing the Paper Width This printer accommodates 80 mm wide roll paper with no adjustments. For rolls from 38 mm to 70 mm wide, use the roll paper spacer included with the printer. If the rolls are from 61 to 70 mm wide, break two tabs off the back of the roll paper spacer. (You can still use widths from 38 mm to 60 mm with the roll paper spacer with the tabs broken off) Follow the steps below to attach the roll paper spacer. Tabs 1. 2. 3.
English 4. Push the roll paper spacer until you feel it clicks onto the shaft. Check that the roll paper spacer slides smoothly to the left and right. Hook Inside edge Shaft Ruler 5. Slide the roll paper spacer to the appropriate width. You can use the measurement printed inside the printer, aligning the inside edge of the spacer with the desired measurement. Note: When you want to set the roll paper width from 61 mm to 70 mm, break off by hand the two tabs of the spacer.
English Connecting the Cables 1. Place the printer and pull the cover in the direction of the arrow in the illustration to remove the cover. 2. Break off by hand any of the three portions indicated by circles in illustration to pass the cables through. 3. 4. Connect the cables to the printer. Attach the cover while passing the cables through the holes.
English Installing the Roll Paper 1. 2. Make sure that the power is on. Pull the peeler open lever forward and open the peeler cover. CAUTION: If you open the roll paper cover with roll paper installed, make sure to open the peeler cover first, and then the roll paper cover. If you open them in the reverse order, the roll paper can get trapped under the roll paper cover when it is closed, causing a possible paper jam. Peeler open lever 3.
English 4. Insert the roll paper. 5. You can switch the issuing mode between the label continuous issuing mode (issue the label continuously) and the label peeler issuing mode (after the issued label is removed, the printer issues the next label). Make sure that the mode switch is set to the mode you are going to use.
English 6. Pull out the paper until the end exactly reaches the guideline. Note: Making sure the paper end is at the guideline reduces the number of labels required for detecting the minimum paper length. The number of labels issued depends on the length of the label, but 2 labels are issued when the length of the label is less than 50 mm {2"}, and 1 label is issued when it is 50 mm {2"} or more. 7. Eliminate any slack in the roll paper, and then close the roll paper cover.
English 9. Refer to step of the same mode that you set in step 5. Label continuous issuing mode Close the peeler cover. Label peeler issuing mode Pass the paper through the peeler, and close the peeler cover. 10. Press the PAPER FEED button. 11. The paper is automatically fed backward, and the PAPER OUT LED goes off. Note: While a label is being issued, do not touch it until the PAPER OUT LED starts flashing. Pulling it before that may result in the waste of a label.
English Cleaning the Thermal Head CAUTION: After printing, the thermal head can be very hot. Be careful not to touch it and to let it cool before you clean it. Do not damage the thermal head by touching it with your fingers or any hard object. Epson recommends cleaning the thermal head periodically (generally every 6 months) to maintain receipt print quality. 1. Turn off the printer, open the peeler cover, and then the roll paper cover. 2.
English Cleaning the Platen Roller/Roll Paper End Sensor When paper dust accumulates on the platen roller or the roll paper end sensor, follow the steps below to clean them. To maintain good functional capabilities, clean them regularly (every 6 months). 1. Turn off the printer, open the peeler cover, and then the roll paper cover. 2. Clean the platen roller and roll paper end sensor with a cotton swab lightly moistened with water or an alcohol. Platen roller Roll paper end sensor . 3.
English Cleaning the Peeler Unit After the peeler is used for a prolonged period of time, the glue from the labels accumulates on the rollers of the peeler unit. If you leave the rollers in such a condition, the glue may stick to issued labels, or a paper jam may occur. To prevent malfunctions and maintain good print quality, clean the rollers regularly (every 100,000 labels). You can clean them easily if you use a wasted label. Note: Do not use any alcohol based solvents for cleaning.
English Troubleshooting ERROR LED is on or flashing ❏ ❏ ❏ Make sure that the roll paper cover is closed and the PAPER OUT LED is not on. Close the cover or replace the paper if necessary. If the printer has been printing a lot and the print head gets too hot, the ERROR LED starts flashing, and printing stops. When its temperature cools down to the normal range, printing resumes automatically. Turn off the printer and then turn it back on.
English TM-L90 Specifications . Print method Thermal line 8 dots/mm × 8 dots/mm (203 dpi × 203 dpi) Print width 72 mm, 576 dot positions (receipt roll paper with 80 mm width) Paper dimensions 37.5 ± 0.5 ~ 69.5 ± 0.5 mm, 79.5 ± 0.5 ( max roll diameter 90 mm) Interface (compatible) Serial (RS-232) Parallel (IEEE 1284) Ethernet (10BASE-T/100BASE-TX) USB [Compliance: USB 2.0, Communication speed: Full-speed (12 Mbps)] Wireless (IEEE802.
