TM-J2000/J2100 User’s Manual / Bedienungsanleitung Gebruikershandleiding / Manuel d’utilisation Manual do utilizador / Manual del usuario Manuale dell’utente 401303603
Part Names cutter cover emergency cutter control panel 2 1 ink cartridge cover 3 4 5 6 paper roll cover power supply switch DIP Switch Tables Serial transmission speed Serial SW Function ON 1-1 Power button function Disabled OFF 1-7 1-8 Enabled ON ON Transmission speed 9600 bps 19200 bps 1-2 Interface condition selection by the DIP by the switch memory switch OFF ON ON OFF 38400 bps 1-3 Handshaking XON/XOFF DTR/DSR OFF OFF 115200 bps 1-4 Data word length 7 bits 8 bits 1-5
English All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein.
English Safety Precautions This section presents important information intended to ensure safe and effective use of this product. Please read this section carefully and store it in an accessible location. WARNING: Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a SEIKO EPSON service center for advice. Never attempt to repair this product yourself.
English Do not disassemble the cartridge. The ink can permanently stain clothing. Do not refill ink cartridges. Spills can result, causing damage to the printer. Be sure the storage temperature stays between 0 and 40 ºC {32 and 104 ºF}. Do not remove the cartridge except to replace it or to prepare the printer for shipment.
English The Control Panel TM-J2000 TM-J2100 LEDs POWER LED Lights when the power is on and is off when the power is off; flashes during cleaning and other operations. Note: Never turn off the printer when the POWER LED is flashing. ERROR LED Off when the printer is online, lights when the printer is offline, and flashes when an error occurs. PAPER OUT LED Lights when roll paper is out or nearly out. INK OUT LED Off when the ink supply is adequate.
English Power Switch and Power Switch Cover The power switch is on the front of the printer. Press it to turn on the printer, and press and hold it for more than 3 seconds to turn off the printer. Note: Never turn off the printer when the POWER LED is flashing. power switch power switch cover Power Switch Cover You can use the enclosed power switch cover to make sure that the power switch is not accidentally pressed. Just press the cover into place to install it.
English 2. Carefully lift where LIFT is marked on the paper roll cover, and pull the paper roll cover toward you. 3. Remove the used paper roll core if there is one. 4. Put the paper roll inside the printer in the correct direction, as shown in the illustrations below. 5. Pull the leading edge of the roll paper a little beyond the paper roll cover, and then close the paper roll cover. WARNING: Be careful not to catch your finger in the printer when you close the paper roll cover.
English 6. If you close the cover correctly, you will feel it fit into place, and the printer will automatically feed approximately 7 cm {2.76 in.} of roll paper. approximately 7 cm {2.76 in.} 7. The roll paper is cut automatically. Note: Do not touch the paper roll cover during printing, paper feed, or cleaning. CAUTION: When using a partial cut, be sure to tear off the paper by pulling it in the direction shown. Otherwise, the cut edge of the paper may not be smooth.
English Note: Use Seiko Epson specified ink cartridges. Performance of the printer when other ink cartridges are used is not guaranteed. Follow these steps to install an ink cartridge for the first time or to replace an empty ink cartridge. 1. Make sure the printer is on. If it is not on, plug in the AC adapter and turn on the power using the switch on the front of the printer. 2. Be sure that a paper roll is installed. 3. Open the ink cartridge cover. 4. Pull the ink cartridge lever toward you.
English 7. Push the cartridge lever back to its original position. You will feel the cartridge fit into place. Note: The INK OUT LED will now be off. 8. Close the ink cartridge cover. The POWER LED flashes for approximately 1 minute as the ink delivery system is charged. Note: Do not turn off the power supply while the POWER LED is flashing. This will shorten the life of the ink cartridge. When the POWER LED quits flashing and stays on, the printer is ready for printing.
English Disposal of Used Cartridges Dispose of used ink cartridges as industrial waste products. Obey the laws and regulations of your country and district. Ink Cartridge Life To make your ink cartridges last as long as possible, follow these simple rules: ❏ Do not turn off the power supply switch immediately after printing is completed. ❏ Do not open the ink cartridge lever or remove the ink cartridge unless you are replacing the cartridge. ❏ Do not turn the printer on and off unnecessarily.
English Cleaning the Print Head If printing becomes faint or uneven and the INK OUT LED is not on or flashing, press the CLEANING button until the printer mechanism begins to clean the print head (more than 3 seconds). When the cleaning stops, the printer is ready for normal printing. Transporting To transport this printer, follow these steps: 1. Remove the ink cartridge. 2. Turn off the power supply. 3. Check that the POWER LED is off. 4. Remove the power supply connector. 5.
English TM-J2000/J2100 Specifications Print Method Resolution Serial Ink Jet Dot Matrix Method Normal, High speed, Economy: 180 × 180 dpi Bar Code: 360 × 360 dpi Fonts (Includes Horizontal Font A: 12 × 24 2 Dot Spaces) Font B: 9 × 17 Print Width 50.8 / 61 / 67.7 / 72.2 mm {2.0 / 2.4 / 2.7 / 2.8"} Character Size: (W × H) Font A: 1.41 × 3.39 mm {0.06 × 0.13"} Font B: 0.99 × 2.40 mm {0.04 × 0.
