User's Guide NPD4674-07 EN
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Copyrights and Trademarks Copyrights and Trademarks No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson printer.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Contents Contents Positioning of the pressure rollers and media (For SC-S70600 series and SC-S50600 series) ................................... Loading Media (SC-S70600 series, SC-S50600 series). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Loading Media (SC-S30600 series). . . . . . . . . . Viewing and Changing Media Settings. . . . . . . Replacing and removing media. . . . . . . . . . . .
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Contents Cleaning the Sides of the Auto Take-up Reel Unit (When It Is Dirty). . . . . . . . . . . . . . . . . . 116 Cleaning Check Sheet. . . . . . . . . . . . . . . . . . . 117 Replacing Consumables. . . . . . . . . . . . . . . . . . . . 118 Shaking and Replacing Ink Cartridges . . . . . . . 118 Disposing of Waste Ink. . . . . . . . . . . . . . . . . . 119 Replacing the Wiper and Wiper Cleaner. . . . . .
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction ❏ Use only the power cord that comes with this product. Use of another cord may result in fire or electric shock. Introduction ❏ Do not use a damaged or frayed power cord. Important Safety Instructions ❏ If you use an extension cord with this product, make sure the total ampere rating of the devices plugged into the extension cord does not exceed the cord’s ampere rating.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction ❏ This device has two power systems. There is a risk of electric shock unless the two power cables are unplugged during the maintenance. When handling the ink cartridges ❏ Keep ink cartridges out of the reach of children and do not drink. ❏ Do not touch the green IC chip on the side of the cartridge. This may affect normal operation and printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series Introduction SC-S30600 seriesU https://www.youtube.com/ playlist? list=PLD67cTLxxk9P6FW3ylGgUd98QUDyAFEGr If the subtitles are not displayed when you play the video, click the subtitles icon shown in the image below. Illustrations Unless otherwise noted, the illustrations in this manual show the SC-S30600 series.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Printer Parts Front section (SC-S70600 series, SC-S50600 series) The illustration shows the SC-S50600 series. A Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. U “Cleaning Around the Print Head (Daily)” on page 103 B Additional print drying system The heater can be used to rapidly dry ink after printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction E Tensioner media guide The tensioner media guide prevents the take-up roll from skewing when using the auto take-up reel unit. When not using the auto take-up reel unit, move the guide out of the way toward both edges of the tensioner. U “Using the Auto Take-up Reel Unit” on page 67 F Tensioner The tensioner maintains tension to prevent the media sagging as it is taken up.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction S Cartridge check lamp This lamp lights when an ink cartridge error occurs. On : An error occurred. Check the contents of the error on the control panel's screen. Off : No error. T AC inlet #1/AC inlet #2 Connects the power cable. Be sure to connect both cables. U LAN port U “LAN port” on page 18 V USB port Connects the USB cable. W Maintenance cover (right) Open this cover when performing regular maintenance.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Front section (SC-S30600 series) A Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. U “Cleaning Around the Print Head (Daily)” on page 103 B After heater The heater can be used to rapidly dry ink after printing. U “Heating & Drying” on page 85 C Roll core holder Place the roll core for media take-up on these holders.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction F Roll core holder locking screw The locking screws keep the roll core holders in place once they have been attached to the roll core. There are same parts on both the left and the right. G Roll support Rest media temporarily on these supports when removing the take-up roll. There are same parts on both the left and the right. H Auto switch Use this switch to select the auto take-up direction.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction T LAN port U “LAN port” on page 18 U USB port Connects the USB cable. V Maintenance cover (right) Open this cover when performing regular maintenance. Normally closed when using the printer. U “Cleaning” on page 103 W Media loading lever After loading media, lower the media loading lever to keep the media in place. Raise the lever to release the media prior to removal.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Inside (SC-S70600 series, SC-S50600 series) Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. The illustration shows the SC-S70600 series. A Print head The print head prints by moving left and right while emitting ink. The print head on the left is “Head1”, the print head on the right is “Head2”.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction F Platen heater The platen heater ensures that the ink adheres evenly. U “Heating & Drying” on page 85 U “Cleaning Inside the Printer (Once a week to once a month)” on page 113 G Wiper cleaner The wiper cleaner removes ink from the wiper. This is a consumable; replace about once every three months.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Inside (SC-S30600 series) Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. A Print head The print head prints by moving left and right while emitting ink. We recommend that this unit be cleaned at the end of each workday.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction F Wiper cleaner The wiper cleaner removes ink from the wiper. This is a consumable; replace about once every three months. U “Replacing the Wiper and Wiper Cleaner” on page 120 G Caps Except during printing, these caps cover the print head nozzles to prevent them drying out. We recommend that this unit be cleaned at the end of each workday.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction C Roll holder fixing screw These screws fix the roll holders in place once the media has been installed. There are same parts on both the left and the right. D Lift lever If the media to be mounted on the roll holders seems heavy, use these levers to raise the media effortlessly to the level of the roll holders. There are same parts on both the left and the right.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Data lamp Status lamp (green/red) On On (green) Flashing On Status The printer is connected using a 1000base-T connection. The printer is receiving data over a 1000base-T connection. On (red) Flashing The printer is connected using a 100base-TX connection. The printer is receiving data over a 100base-TX connection.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction D Display Displays the printer's status, menus, error messages, and so on. U “Understanding the Display” on page 21 Control panel E Menu button Press this button to display menus. U “Using the Control Panel Menu” on page 137 F y button (back button) Press this button to exit to the previous menu when options are displayed.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction J ❏ Pressing this button when a menu item is highlighted displays options for the selected item. Understanding the Display ❏ Pressing this button when an option is highlighted selects the highlighted item or performs the selected operation. The illustration shows the display for the SC-S50600 series. ❏ Pressing this button while the alert buzzer is sounding stops the buzzer.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction : 1.5 : An error occurred. Check the message on the screen, and clear the error. : 2.0 : A Cleaning cartridge is installed. The height of the indicator changes with the level of cleaning fluid remaining. : 2.5 ❏ The media remaining is not displayed if Off is selected for Remaining Setup in the Media Remaining menu.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction This display shows settings for the additional print drying system (supplied with the SC-S50600 series; optional with other models). SC-S30600 series BK : Black Y : Yellow : Not installed, or it is not installed correctly. M : Magenta : The drying fan is enabled. C : Cyan No icon : The drying fan is not enabled. To start the fan, select Additional Dryer for On in the setup menu.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Additional Print Drying System Available The additional print drying system (supplied with the SC-S50600 series; optional with other models) can be used for increased drying performance and improved productivity. It is recommended when using the SC-S70600 series in 10 Color mode, as the white and metallic silver inks are slow to dry.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Nearly Odorless Solvent Ink The distinctive odor of solvent-based inks has been reduced with our solvent inks. This not only improves the work environment during printing but ensures that items intended for indoor display can be exhibited in any venue. Notes on Usage and Storage In this document, White ink and Metallic Silver ink are listed as "spot color ink".
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction the media. For more information, see the documentation supplied with the media. Notes when not using the printer Also, when operating in dry areas, air conditioned environment, or under direct sunlight, maintain the appropriate humidity. If you are not using it, note the following points when storing the printer. If it is not stored correctly, you may not be able to print properly the next time it is used.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction ❏ Store the printer after confirming that the print head has been capped (the print head is positioned at the far right). If the print head is left uncapped for a long time, the print quality may decline. ❏ Do not touch the ink cartridge IC chip. You may not be able to print properly. ❏ In 8 Color (Fixed) mode or 4C Mode, use replacement cartridges as well to fill all slots with cartridges.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction ❏ Do not dismantle or remodel ink cartridges. You may not be able to print properly. ❏ Do not rub or scratch the printed surface. If they are rubbed or scratched, the ink may peel off. ❏ Do not drop or knock it against hard objects; otherwise, the ink may leak from the cartridge. ❏ Do not touch the printed surface, as this may remove the ink.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series Introduction ❏ To cancel auto ink circulation, press the W button while Circulating ink... is being displayed on the control panel screen. However, it cannot be canceled while ink circulation is required. If auto ink circulation is canceled to make prints using spot color inks, tint unevenness may occur in printing results.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Using the Supplied Software Contents of the Software Disc The following applications are available on the supplied software disk. Install as required. For information about these applications, see the Network Guide (pdf) or the on-line help for the application in question. Note: ❏ The supplied disk does not contain printer drivers. A software RIP is required for printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Introduction Uninstalling Software Starting EPSON LFP Remote Panel 2 c ❏Important: Log in to a "Computer administrator" account Launch EPSON LFP Remote Panel 2 after confirming that the printer displays Ready. (an account with Administrators group privileges). Windows The application can be launched using either of the following two methods. A B ❏ Double-click the EPSON LFP Remote Panel 2 icon on the desktop.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series Introduction E Follow the on-screen instructions to continue. When the delete confirmation message appears, click Yes. If you are reinstalling the Epson communications driver, restart the computer. Mac OS X The following describes how to remove the EPSON LFP Remote Panel 2. A Quit EPSON LFP Remote Panel 2. B Select Applications - Epson Software, and drag and drop the entire EPSON LFP Remote Panel 2 folder into Trash to delete.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations !Caution: ❏ The heaters and media holding plate may be Basic Operations hot; observe all necessary precautions. Failure to observe the necessary precautions could result in burns. Loading and Exchanging Media The process for loading media varies with the model of printer or type of media feeding unit used. Choose the method suited to your particular setup.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations 34
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Positioning of the pressure rollers and media (For SC-S70600 series and SC-S50600 series) Pressure rollers must be set in the correct position to obtain good print results. Positioning of media There are square holes to indicate the pressure roller positions on the rear side of the printer.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Pressure roller types There are two types of pressure rollers. As shown below, the pressure roller to use depends on the type of printing. Normal printing Use low pressure rollers . Note that the quantity of rollers to use depends on the media width. When transparent or milky white film is loaded or during ink layering Use high pressure rollers .
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations B Loading Media (SC-S70600 series, SC-S50600 series) Open the front cover, and move the media holding plates out of the way. c IfImportant: the media holding plates are not moved out Follow the steps below when using the supplied media feeding unit. of the way, media insertion may fail or damage may occur to the edge of the media.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations C Loosen the roll holder fixing screws sufficiently and adjust the roll holders so that the distance between the two is wider than the media. Note: The method of placing the roll media varies as follows depending on how media is rolled. Center the roll supports between the roll holders.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations F H Raise the lift lever on the left side of the printer to lift the media into position, then firmly insert the roll holder. Note: If the media roll has an outer diameter that is less than 140 mm, lift it manually, and load it to the roll holder. The roll core will not reach the holder when raised using the lift lever.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations K c IfImportant: the roll holder is inserted into the roll core Rotate the handle until part A in the illustration below is fully inserted. insufficiently, media is not fed correctly during printing because of slippage between the roll holder and roll core. This may cause banding in the print results. J Tighten the roll holder screw until the screw no longer turns to fix the roll holder in place.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations M N Insert the media approximately 30 cm into the opening, then lower the media loading lever. O Hold the center of the media and raise the media loading lever. P Pull the media straight to the center of the after heater. Check that the edges of the media pass within the dimensions of the square that was adjusted in Step 5.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Q When transparent or milky white film is loaded or during ink layering Hold both sides of the pressure roller, and move while pressing it down to set. Note: Do not touch the shaft (grayed part in the figure) at the top of the roller. Otherwise you might get grease on your skin. R Normal printing ❏ Use low pressure rollers. Move the high pressure rollers to right or left until they contact the ends.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations S Set the media holding plates at both sides of the media. Sliding media holding plates While holding the tabs of the media holding plates on both sides, move the plate to the edge of the media. Adjust so that the edge of the media is aligned to the center of the round holes in the media holding plates. c ❏Important: Do not use the media holding plates with media that is 0.4 mm or thicker.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations B When using the auto take-up reel unit, see: U “Using the Auto Take-up Reel Unit” on page 67 Open the front cover, and move the media holding plates out of the way. c IfImportant: the media holding plates are not moved out When not using the auto take-up reel unit, proceed to the media check and setting change steps. of the way, media insertion may fail or damage may occur to the edge of the media.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations C U “Positioning of the pressure rollers and media (For SC-S70600 series and SC-S50600 series)” on page 35 Loosen the left and right roll holder fixing screws sufficiently and separate the roll holders so that the distance between them is wider than the media. c IfImportant: the right holder handle shaft is not visible, rotate the handle forward until it stops.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations G Fully insert the left roll holder. Next, tighten the roll holder screw until the screw no longer turns to fix the roll holder in place. H Fully insert the right roll holder. I To ensure the roll holder is inserted into the roll core sufficiently, push the center section on the side of the roll holder towards the roll end twice.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations J L Tighten the roll holder screw until the screw no longer turns to fix the roll holder in place. Rotate the handle until part A in the illustration below is fully inserted. Important: c Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations N O Insert the media approximately 30 cm into the opening, then lower the media loading lever. P Hold the center of the media and raise the media loading lever. Q Pull the media straight to the center of the after heater. Check that the edges of the media pass within the dimensions of the square that was adjusted in Step 5.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations R When transparent or milky white film is loaded or during ink layering Hold both sides of the pressure roller, and move while pressing it down to set. Note: Do not touch the shaft (grayed part in the figure) at the top of the roller. Otherwise you might get grease on your skin. S Normal printing ❏ Use low pressure rollers. Move the high pressure rollers to right or left until they contact the ends.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations T Set the media holding plates at both sides of the media. Sliding media holding plates While holding the tabs of the media holding plates on both sides, move the plate to the edge of the media. Adjust so that the edge of the media is aligned to the center of the round holes in the media holding plates. c ❏Important: Do not use the media holding plates with media that is 0.4 mm or thicker.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations When using the auto take-up reel unit, see: Sliding media holding plates Move the media holding plates to the right and left sides of the platen. Hold both tabs on the media holding plates to move them. U “Using the Auto Take-up Reel Unit” on page 67 When not using the auto take-up reel unit, proceed to the media check and setting change steps.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations E c IfImportant: the right holder handle shaft is not visible, Align the left edge of the media with the position on the label. rotate the handle forward until it stops. The media can not be properly loaded if the handle shaft is not visible. D Temporarily place media on the roll supports. Note: If the label does not have the loading position, mark it on the label as instructed in the Setup Guide.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Note: If the media roll has an outer diameter that is less than 140 mm, lift it manually, and load it to the roll holder. The roll core will not reach the holder when raised using the lift lever. G Tighten the roll holder screw until the screw no longer turns to fix the roll holder in place. H Raise the lift lever on the right side of the printer to lift the media into position, then firmly insert the roll holder.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations J Tighten the roll holder screw until the screw no longer turns to fix the roll holder in place. Important: c Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. If part A is still visible even after the handle has been turned fully, rewind the handle. Loosen the roll holder screw on the right side, and then restart from Step 8.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations N P Confirm that the left edge of the media passes within the square of the label on the pre-heater. Pull the media straight to the center of the after heater. ❏ Do not pull the media with both hands. This could cause the media to skew or move around. ❏ The labels on the after heater are not used when media is loaded. If it is adjusted to forcefully, the media way move around or become loose.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations R Set the media holding plates at both sides of the media. Sliding media holding plates While holding the tabs of the media holding plates on both sides, move the plate to the edge of the media. Adjust so that the edge of the media is aligned to the center of the round holes in the media holding plates. c ❏Important: Do not use the media holding plates with media that is 0.4 mm or thicker.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations When using the auto take-up reel unit, see: Sliding media holding plates Move the media holding plates to the right and left sides of the platen. Hold both tabs on the media holding plates to move them. U “Using the Auto Take-up Reel Unit” on page 67 When not using the auto take-up reel unit, proceed to the media check and setting change steps.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations c IfImportant: the right holder handle shaft is not visible, Note: If the label does not have the loading position, mark it on the label as instructed in the Setup Guide. rotate the handle forward until it stops. The media can not be properly loaded if the handle shaft is not visible. D U Setup Guide E Align the media and the roll holders. F Fully insert the left roll holder.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations G Fully insert the right roll holder. H To ensure the roll holder is inserted into the roll core sufficiently, push the center section on the side of the roll holder towards the roll end twice. I Tighten the roll holder screw until the screw no longer turns to fix the roll holder in place. c IfImportant: the roll holder screw is loose, the roll holder may move during printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations K Rotate the handle until part A in the illustration below is fully inserted. M Insert the media approximately 30 cm into the opening, then lower the media loading lever. N Confirm that the left edge of the media passes within the square of the label on the pre-heater. Important: c Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations O Hold the center of the media and raise the media loading lever. P Pull the media straight to the center of the after heater. Q Lower the media loading lever to hold the media in place. R Set the media holding plates at both sides of the media. Sliding media holding plates While holding the tabs of the media holding plates on both sides, move the plate to the edge of the media.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Insertable media holding plates Position the media holding plates, while the media is placed over them, in such a way that each edge of the media is aligned to the middle of a row of the round holes in the media holding plates. c ❏Important: Do not use the media holding plates with media that is 0.4 mm or thicker. The media holding plates could touch and damage the print head.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations ❏ Selected Media Viewing and Changing Media Settings Displays the parameters on which media settings are based as shown below. The control panel displays the following information once the media is loaded. RIP Settings: Media settings are based on those in the RIP. XXXXXXXXXXXXXXXXXX: Media settings are based on those stored in the printer in media settings bank No. 1.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations E After confirming that the settings are correct, use the d/u buttons to select Keep Settings Above and press the Z button. F The roll type selection screen is displayed. G If On is selected for Remaining Setup, you will be prompted to enter the length of the current media. Use the d/u buttons to choose a length between 1.0 and 999.5 m and press the Z button. You can set in 0.5 m increments.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations When the auto take-up reel unit is used, raise the tensioner. Buttons that are used in the following settings C A After checking that the printer is ready, press the button, and press the Z button. B Check that the trailing edge of the printed media is fed to the position over the cutter groove, and open the front cover. Open the front cover, and move the media holding plates out of the way.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations D G Cut the media with the cutter. Pass the blade of the cutter down the cutting groove. To remove the media, reverse the steps you followed to load it. U “Loading Media (SC-S70600 series, SCS50600 series)” on page 37 U “Loading Media (SC-S30600 series)” on page 51 Important: c To finish the procedure in the SC-S70600 series or SC-S50600 series, raise the media loading lever.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Using the Auto Take-up Reel Unit Notes when using the auto take-up reel unit !Caution: ❏ Follow the instructions in the manual when The auto take-up reel unit automatically takes up media as it is printed. This improves the efficiency of unmanned operation. loading media or roll cores or removing the take-up roll. Dropping media, roll cores, or take-up rolls could result in injury.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations B Before starting operations, be sure to read the following: U “Notes when using the auto take-up reel unit” on page 67 Loosen the roll core holder fixing screws at both sides and adjust the left roll core holder. Center the roll supports between the roll holders.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations D When using the heavy roll media system (optional): Proceed to step 7. Cut the left and right corners of the media as shown in the illustration below. F Cutting the media prevents feeding problems, such as the left and right corners of media being folded and caught at the start of take-up. Push the holder until part A shown in the illustration below is fully inserted, and tighten the screw.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations G Securely push the roll core holder into the roll core using both hands, and then tighten the fixing screws. Rotate the handle until part A in the illustration below is fully inserted.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Important: c Attach the media to the take up roll core with F Continue holding down the d button until both edges of the media reach the paper core and wrap around once or twice. G Position the right and left tensioner media guides until they slightly touch the media. the media in a taut state. If media is attached in a loose state, the media may move around during take-up. D E Flip the Auto switch to .
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations H When loading banner media, attach three counter weights to both ends of the tensioners. c ❏Important: Always attach three each on the left and right. Take-up will not be performed correctly if counterweights are added to one side only or the quantities are different on the left and right. ❏ For media other than banner media, always remove the counterweights before printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations When there is no paper tape While pulling the center section of the media straight down, affix the media to the take up roll core with tape. A C Flip the Auto switch to Off, and hold down the to wrap the media once Manual switch to around the roll core. D Flip the Auto switch to Important: c Attach the media to the take up roll core with the media in a taut state.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations E Lower the tensioner until it slightly touches to the media. F Confirm that the media is attached without looseness. If the tension on the left and right of the media is different in the areas shown in the illustration below, the media will not be taken up correctly. When one side is loose, restart the procedure from Step 1.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations I When loading banner media, attach three counter weights to both ends of the tensioners. c ❏Important: Always attach three each on the left and right. Take-up will not be performed correctly if counterweights are added to one side only or the quantities are different on the left and right. ❏ For media other than banner media, always remove the counterweights before printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Take-up with the Printed Side Facing In A B C Important: c Attach the media to the take up roll core with the media in a taut state. If media is attached in a loose state, the media may move around during take-up. Cut the paper tape approximately 60 cm in length, and paste it approximately in the center of the media using commercially available adhesive tape.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations F Continue holding down the d button until both edges of the media has wrapped around once or twice. G Position the right and left tensioner media guides until they slightly touch the media. H 77 When loading banner media, attach three counter weights to both ends of the tensioners.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations When there is no paper tape While pulling the center section of the media straight down, affix the media to the take up roll core with tape. c ❏Important: Always attach three each on the left and right. A Take-up will not be performed correctly if counterweights are added to one side only or the quantities are different on the left and right.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations C Flip the Auto switch to Off, and hold down the to wrap the media once Manual switch to around the roll core. E Lower the tensioner until it slightly touches to the media. F Confirm that the media is attached without looseness. If the tension on the left and right of the media is different in the areas shown in the illustration below, the media will not be taken up correctly.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations G Continue holding down the d button until the media reach the paper core and wrap around once or twice. H Position the right and left tensioner media guides until they slightly touch the media. I 80 When loading banner media, attach three counter weights to both ends of the tensioners.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations When the Heavy Roll Auto Take-up Reel Unit is installed U “Using the Optional Heavy Roll Auto Take-up Reel Unit” on page 82 c ❏Important: Always attach three each on the left and right. Take-up will not be performed correctly if counterweights are added to one side only or the quantities are different on the left and right.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations E To prevent the media from sliding off the roll, support the roll at its right end. F Loosen the right roll core holder fixing screw and remove the roll core holder from the roll. G Lower the roll onto the roll support. A Cut the media and roll the cut end onto the take-up reel.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations ❏ Check the amount of ink remaining: ❏ Auto Media Adjust ❏ Media Adjust If ink is expended during printing, printing can be resumed once the affected cartridge has been replaced. However, when replacing ink during a print job, you may see a difference in color depending on the drying conditions.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Precautions regarding settings Buttons that are used in the following settings ❏ Correctly load the media to be adjusted in the same state as for the actual printing. For example, if you are using the auto take-up reel unit for printing, the auto take-up reel unit should also be used for adjustment.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Setting procedure Load the media according to the actual usage conditions. Auto Media Adjust A When this menu is executed, the printer automatically reads adjustment patterns using the sensor while printing the patterns, and continuously performs Feed Adjustment and Head Alignment. When usage conditions change, the adjustment results will also change.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations C Choose a value. Media Adjust Heater Temperature The temperatures for the pre-, platen, and after heaters can each be adjusted separately. This menu is used to adjust media when Auto Media Adjust cannot be used or when reconfiguring media settings is required due to a change made in printing conditions after saving the media settings. In this menu, perform Feed Adjustment and Head Alignment individually.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations This menu provides two modes: Auto and Manual. Auto The printer reads adjustment patterns using the sensor while printing the patterns, and makes adjustment automatically. Manual Visually check the printed adjustment patterns, and specify the optimal adjustment values. Use this if graininess or misalignment occurs when using Auto. SC-S70600 series, SC-S50600 series Manual Standard roll media system Approx.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations J Pattern length is displayed in the control panel. Use the r/l buttons to change the numeric value to the value obtained in Step 9, and press the Z button. When the setting is completed, the printer returns to the Ready state. Head Alignment B Press the Menu button to display the setup menu. C Use the d/u buttons to select Media Setup, and press the Z button.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations In Standard (Manual) Heating & Drying Buttons that are used in the following settings A In Block pattern C1 1 2 The screen to enter a numeric value is displayed. Using the u/d buttons, enter the pattern number recorded in Step 9 and press the Z button. K When multiple check patterns have been printed, select the number per check pattern, and then press the Z button. button during printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations D Feed Adjustment Buttons that are used in the following settings A B Press the Note: If the setting is changed, the icon is displayed on the control panel screen as shown below. To clear this icon, carry out the following operations. button during printing. The current adjustment value is displayed. Use the d/u buttons to change the current value.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations Printable area SC-S70600 series/SC-S50600 series The printable area depends on whether low or high pressure rollers are used to set the media. When using low pressure rollers (normal printing) The gray area in the illustration below shows the printable area. The arrow indicates the feed direction. "A" indicates the pressure rollers on both edges when the pressure rollers have been set correctly on the media.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations A to D indicates the margins on all four sides. See the following for more details. Margin Position Explanation Available Setting Range A Bottom*1 This can be configured in RIP. To maintain media feeding accuracy, if the settings are less than 5 mm or more than 17 mm, the settings are switched to 5 mm and 17 mm respectively. 5 to 17 mm B Top*1 This can be configured in RIP.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations When using high pressure rollers (when using transparent or milky white film or for ink layering) The printable area is the area excluding the margins configured from the positioning of pressure rollers. (See the gray area in the illustration below.) The arrow indicates the feed direction. "A" indicates the position of the high pressure rollers. A to D indicates the margins on all four sides.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations *2 This may be available in the RIP depending on the software RIP being used. Contact the RIP manufacturer for more information. *3 Note the following points when setting margins. ❏ Regardless of the Media Size Check setting, the margin start point is within "A" (indicated by the broken line).
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations * When Media Size Check is set to Off, this is 1,626 mm (64 inches) regardless of the width of the loaded media. A to D indicates the margins on all four sides. See the following for more details. Margin Position Explanation Available Setting Range A Bottom*1 This can be configured in RIP.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Basic Operations *3 Note the following points when setting margins. ❏ Leave margins of 10 mm or more when using media holding plates. Narrower margins could result in printer printing over the plates. ❏ If the total of the print data width and set left and right margins exceeds the printable area, a portion of the data will not be printed.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Maintenance When to Perform Various Maintenance Operations It is necessary to perform proper maintenance at appropriate frequency to maintain print quality. Failure to perform appropriate maintenance will shorten product life. Read this section and perform maintenance appropriately. This document comes with a check sheet so that you can tell at a glance when maintenance was last performed.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance When to perform Component to be cleaned Daily (at the end of every workday) ❏ Around the print head U “Cleaning Around the Print Head (Daily)” on page 103 If maintenance is not performed, ink hardens and is difficult to remove. ❏ Around the caps (wiper (rubber part), caps, wiper cleaner) U “Cleaning Around the Caps (Daily)” on page 106 The video is available to check the procedure. SC-S70600 seriesU https://www.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance When to perform Component to be replaced Once every three months ❏ Wiper, wiper cleaner Be sure to replace the wiper and the wiper cleaner at the same time. These should also be replaced if ink adheres to the absorbent section on the rear of the wiper cleaner, or when the wiper section is worn or deteriorated.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance When to perform Type ❏ Change Color Mode (SC-S70600 series only) ❏ When spot color ink printing is not carried out for longer than a specified period of time When spot color ink printing is restarted When the following message is displayed on the control panel screen The specified period guideline varies with the selected ColorMode.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance A metal tray (supplied with the printer) Preparation and Notes What You’ll Need Ready the following items before beginning cleaning and replacement. Use when putting cleaning utensils, removed consumables, or ink cleaner moved in the container supplied with the printer. Protective eyeglasses (available in the market) Protects your eyes from ink and ink cleaner. c IfImportant: the used cleaning stick, etc.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance ❏ Do not touch the tips of the cleaning sticks. Oil from your hands could damage the print head. Precautions regarding maintenance ❏ Do not get alcohol or water on the caps or the nozzle surface. Ink congeals when mixed with water or alcohol. To make maintenance, note the following points.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance B Note: The buzzer sounds 10 minutes after the print head is moved (default setting). Press the Z button to continue the cleaning process. After 10 more minutes have passed, the buzzer sounds again. Dampen the cleaning stick with ink cleaner. Do not allow ink cleaner to drip from the cleaning stick. When dampening a clean-room wiper with ink cleaner, use ink cleaner poured into a cup.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance D Before starting this procedure, be sure to read the following: Important: c Do not touch the parts framed below. Failure U “Precautions regarding maintenance” on page 102 A Wipe off any adhered ink, lint, and dust from the below. parts that are indicated by to observe this precaution could affect print quality. Position the print head for maintenance purposes.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Left-hand print head for SC-S70600 series and SC-S50600 series F Dampen a new clean-room wiper with the ink cleaner, then wipe away any dust and dirt on the front, back, and sides of the wiper blade. G Wipe away ink stains and so on from the print head surface by moving the cleaning wiper from the inside toward you once. Ink is prone to adhere to the areas indicated by the arrows, so be sure to wipe off any ink found.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Before cleaning SC-S70600 series SC-S30600 series SC-S50600 series Wiper 2 1 Caps 10 4 Wiper cleaner 2 1 Before starting this procedure, be sure to read the following: After cleaning The following shows that dried and adhered ink, lint, and dust are cleanly removed.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance C Clean the front and back of the rubber on the wiper with a cleaning stick. For SC-S70600 series and SC-S50600 series, clean the other wipers in the same way. Important: c Do not push strongly against the edges or the surrounding area of the cap, or touch the inner side of the cap with a cleaning stick or tweezers. The part maybe deformed, and it may no longer be possible to perform capping correctly.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance B Cleaning Around the Caps (When Dirty) Hold the cleaning stick flat and wipe the edges of all the caps. Perform the following procedures depending on the condition of the printer. When you have finished, proceed to the cleaning process of the wiper cleaner. U “Cleaning the wiper cleaner (daily)” on page 109 When ink adheres to the guide section Dampen the cleaning stick with ink cleaner.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance When a film of ink adheres to the guide section If a film-like layer of adhered ink cannot be removed completely using a cleaning stick, remove it using tweezers. Cleaning the wiper cleaner (daily) A Press the Z button in the control panel and confirm that the wiper has moved to the back. B Grasp the wiper cleaner as shown and lift it from the printer.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance F U “Replacing the Wiper and Wiper Cleaner” on page 120 D Remove lint or dust that has adhered to the bottom surface of the wiper cleaner using tweezers. E Clean the wiper rail once every two weeks. If two weeks have not passed since the last time the wiper rail was cleaned, go to step 6. U “Cleaning the Wiper Rail (Once Every Two Weeks)” on page 112 Attach the wiper cleaner.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance D Cleaning the Entire Wiper and Attachment Point (Once Every Two Weeks) Press the front and rear side of the rubber part of the wiper against the clean-room wiper, then wipe off any adhered ink clots, lint, and dust. Perform the following cleaning instead of cleaning the wipers (rubber section).
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance F Wipe off any ink that has hardened at the bottom of the wiper with the cleaning stick. Next, proceed to the cap cleaning procedure. U “Cleaning caps (daily)” on page 107 Cleaning the Wiper Rail (Once Every Two Weeks) Perform this after cleaning the wiper cleaner in step 4. U “Cleaning the wiper cleaner (daily)” on page 109 G Wipe off any ink that has hardened at the wiper attachment point with the cleaning stick.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Right and left sides A Make sure the printer is turned off and the screen has turned off, and then unplug the power cable from the outlet. B Leave the printer for a minute. C Open the front cover. D Raise the media loading lever. E Remove stains on the pressure rollers using a dry, soft cloth. SC-S70600 series/SC-S50600 series Wipe while rotating the roller sections one by one.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance G Wipe off the media holding plates using a soft cloth that has been soaked in water. Important: c When media with glue has been used, wipe away glue using a diluted neutral detergent. If glue from the media adheres to the rear side of the plates, it may result in the print head striking during printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance H Insertable media holding plates Remove the media holding plates and wipe stains from the front and rear surfaces. Open the left maintenance cover and clean inside. Wipe lint and dust with a brush or soft cloth that has been soaked in water and squeezed well. I After cleaning, close the front cover and left maintenance cover.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance A E Position the print head for maintenance purposes. The menus will close when the print head returns to its normal position. U “Moving the Print Head” on page 102 B Close the maintenance cover and press the Z button twice. After the print head moves to the left end of the printer, open the right maintenance cover.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Cleaning Check Sheet Print this page to track maintenance tasks.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance If an ink cartridge is expended while printing, you can continue printing after replacing the ink cartridge. However, when replacing ink during a print job, you may see a difference in color depending on the drying conditions. Replacing Consumables Shaking and Replacing Ink Cartridges The following procedure explains how to replace an ink cartridge and a cleaning cartridge.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance DisposalU “Disposal of used consumables” on page 126 Important: c Removed ink cartridges may have ink around the ink supply port, so be careful not to get any ink on the surrounding area when removing the cartridges. D Disposing of Waste Ink Be sure to replace the waste ink bottle when the following message is displayed in the control panel.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Replacing the Waste Ink Bottle Important: c You will need the lid for the waste ink bottle Follow the procedure below to replace the parts. when disposing of waste ink. Keep the lid in a safe place; do not throw it out. Before starting this procedure, be sure to read the following: U “Precautions regarding maintenance” on page 102 A Remove the waste ink bottle from the waste ink bottle holder. C Press the Z button.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance B After the print head moves to the left end of the printer, open the right maintenance cover. C Remove the wiper cleaner. D Grasp the cleaner as shown and lift it from the printer. 121 Insert a new wiper cleaner. Place on the attachment point and press down until you hear a click.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance E G Remove the wiper. Holding the wiper by the attachment point, tilt it left and lift it out. Close the maintenance cover, and then close the setup menu. If the Z button is pressed once, the wiper moves to the inner side. If the Z button is pressed again, the print head returns to its normal position and the menu closes.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Wait until ink stops dripping from the bottom surface of the flashing pad. Remove the pad and then place it in the metal tray. D Insert a new flushing pad. E Close the maintenance cover, and then close the setup menu. Insert the two hooks on the flushing pad into the slots as shown and press the tab down until the pad clicks into place. If the Z button is pressed once, the wiper moves to the inner side.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Replacement procedure A Remove media, and press the P button to turn the printer off. U “Replacing and removing media” on page 64 B Open the left maintenance cover and front cover. C Remove the target media holding plate. Remove the sliding media holding plate in the steps shown below. (1) While holding the tabs of the media holding plate on both sides, move the plate to the left edge of the platen.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance E Check that two hooked sections at the rear of the media holding plate are securely applied as shown below and that they are attached with no gap between the plate and platen.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance F While holding the tabs of each media holding plate on both sides, move both the plates to the left and right edges of the platen respectively. Releasing the tab fixes the media holding plate. G Close the left maintenance cover and front cover.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Consumable Replacement Check Sheet Print this page to track maintenance tasks.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Other maintenance missing colors in the preceding or following printout. Checking for clogged nozzles Use Print Nozzle Pattern with media not suited to Auto Nozzle Check or if you feel that Auto Nozzle Check would take too long. We recommend that you check the nozzles for clogs each time you print to ensure quality results.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance A B After confirming that the printer is ready, press the # button. There is no need to clean the head if the print result does not contain faint areas or other color problems. The Maintenance menu will be displayed. You can also clean the head while printing is paused. Note, however, that hues in the printout may change when printing is resumed. Select Nozzle Check, choose a position, and press the Z button.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance A Pressing the # button when the printer is ready to print displays the Maintenance menu. U “Cleaning Around the Print Head (Daily)” on page 103 Pressing the # button when printing is paused takes you to Step 3. U “Cleaning Around the Caps (Daily)” on page 106 B Use the d/u buttons to select Cleaning and press the Z button. C Choose the nozzles to be cleaned.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Buttons that are used in the following settings Item Explanation All Nozzles Clean all the nozzles of both the print heads. Select this item when faint or missing segments of all colors of both print heads are detected. * "XX" indicates an ink color code. Use Cleaning cartridge (available separately) for Head Washing. The required number of Cleaning cartridge is provided below.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Ink Refresh Ink Refresh is performed. When tint unevenness (areas of uneven density) is detected in printing results, execute Ink Refresh. Long-term Storage (Pre-storage Maintenance) Buttons that are used in the following settings If the printer will not be used for an extended period (and switched off), perform Pre-Storage Maint. in the Maintenance menu before storage.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Interval Cartridges Colors 3 weeks or more 10 All Nozzles (all colors) A After confirming that the printer is ready, press the # button. The Maintenance menu will be displayed. * If the storage interval is short, you can perform Pre-Storage Maint. for spot color ink only. SC-S50600 series (4C Mode) B Use the d/u buttons to select Pre-Storage Maint., and press the Z button.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance Changing from 8 Color (Unfixed) mode ❏ When restarting the use of only the White ink: Select 9 Color. One White ink cartridge is required. Change Color Mode (SC-S70600 series only) The printer consumes ink periodically for auto maintenance.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance A The photo shows SC-S70600 series. After confirming that the printer is ready, press the # button. Greasing procedure The Maintenance menu will be displayed. B Use the d/u buttons to select Change Color Mode, and press the Z button. C Use the d/u buttons to select any mode, and press the Z button.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Maintenance F ❏ Store the container at room temperature with the cap uppermost in a location that is not exposed to direct sunlight. Using a cleaning stick, apply grease to the pad as described below. (1) Fully submerge the tip of the cleaning stick in the grease. (2) Rotate the cleaning stick two or three times, and then remove it. (3) Apply the grease to the pad at the end of the grease tool.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Using the Control Panel Menu Menu Operations The menus are used as shown below.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. Media Setup For more information on these items, see U “The Media Setup Menu” on page 144. Setting items and setting values marked with asterisks indicate the following printer models.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Current Settings RIP Settings Platen Gap 1.5, 2.0, 2.5 Head Alignment Input thickness. 0.1 to 1.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Heating & Drying Heater Temperature Pre-heater/platen heater: 30˚C to 50˚C (86˚F to 122˚F) After heater: 30˚C to 55˚C (86˚F to 131˚F) Drying Time Per Pass 0 to 10 sec After Heater Feed Mode 1, Mode 2, Off Additional Dryer On, Off Advanced Settings Media Tension 0 to 40 Media Suction 0 to 10 Head Movement Data Width, Printer Full Width Tension Measurement Periodically, Every Pa
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Auto Nozzle Check Nozzle Check Cycle Off, 1 to 10 pages Options When Clogged Continue Printing, Stop Printing Print Nozzle Pattern Off, 1 to 10 pages Periodical Cleaning Light Off, 1 to 240 hours Medium Heavy Power*3 Cleaning Cycle Off, 1 to 10 pages Heat Off Timer 15 to 240 minutes Head Mode*1 2 Heads Mode, Head1, Head2 Restore Settings Yes, No Maintenance For more informat
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Ink Refresh All Nozzles, All (except MS/WH)*4, All (except WH)*3, MS/WH*4, WH*1 (The displayed menu varies depending on your model or the specified color mode.) Head Washing XX/XX*3, *4, Head1 XX/XX*2, Head2 XX/XX*2, Head1 All Nozzles*2, Head2 All Nozzles*2, All Nozzles (The displayed menu varies depending on your model or the specified color mode. "XX" indicates an ink color code.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter myEpsonPrinter Status Not Started, Disabled, Enabled Last Uploaded: (Not Uploaded), MM/DD/YY HH:MM GMT Firmware Version XXXXXXX,X_XX,XXXX Network Setup Details on menu U “The Network Setup Menu” on page 154 Item Parameter IP Address Setting Auto - Panel IP: 000.000.000.000 – 255.255.255.255 SM: 000.000.000.000 – 255.255.255.255 DG: 000.000.000.000 – 255.255.255.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Details of the Menu The Media Setup Menu The Media Setup menu can be accessed directly by pressing the M button. indicates default settings. Media Remaining Item Parameter Explanation Remaining Setup On Off Choose On to display and record, or Off to not display and not record, the amount of media remaining. Length, Remaining Alert, and Print Remaining Length options are available when On is selected.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Customize Settings Item Explanation Current Settings To change the currently selected setting, select Current Settings. The customizable setting items vary depending on whether RIP Settings or a media setting bank number 1 to 30 is selected.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Explanation Tension Measurement Periodically Every Page Select Periodically or Every Page to automatically measure the media tension and adjust to the optimal media feeding operation, or Off to disable automatic tension adjustment. Off Periodically is recommended in most circumstances.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Media Adjust Explanation Select this option to adjust media with Auto Media Adjust disabled or make readjustment when changing printing conditions after saving media settings. Feed Adjustment Auto Print In this menu, perform Feed Adjustment and Head Alignment individually.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Explanation Media Tension 0 to 40 Increase tension if creases appear in the media during printing. The higher the value, the greater the tension. Media Suction 0 to 10 When media is waved on the platen, increase the Media Suction. The higher the value, the greater the suction.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Print Media List Parameter Explanation Print Print the contents of media setting banks 1 to 30. The Printer Setup Menu indicates default settings. Setting items and setting values marked with asterisks indicate the following printer models.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Warning Options Parameter Explanation Off Choose whether the printer automatically detects (On) or does not automatically detect (Off), the media rising during printing. On If On is selected, the printer will stop when the media rises to prevent a head strike. On is recommended if you will be performing other tasks and are unable to give the printer your full attention during printing.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Light Medium Parameter Explanation Off Select the timing and intensity level to periodically perform head cleaning. Periodical cleaning will not be performed while Off is selected. If a value between 1 and 240 hours is selected, head cleaning will be performed after the specified number of hours.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Explanation Nozzle Check Print A nozzle pattern will be printed. Inspect the pattern visually and perform head cleaning if you detect faint or missing colors. Print At Right U “Printing nozzle check patterns” on page 128 Print At Center The options available vary with the option selected for Media Size Check and the width of the media used.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Explanation Pre-Storage Maint. MS/WH*4 WH*1 Always perform pre-storage maintenance if the printer will not be used for an extended period (and switched off.) If the storage interval is short, you can perform pre-storage maintenance for spot color ink only. All Nozzles See the following for more information.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Explanation Show Total Prints XXXXXX m2 (XXXXXX ft2) Select Show Total Prints to view the total area of media printed (to a maximum of six figures). The Printer Status Menu These items track printer use and settings. Item Parameter Explanation Print Status Sheet Print Print a status sheet showing current printer settings, and the status of periodic replacement parts.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Using the Control Panel Menu Item Parameter Explanation Date And Time MM/DD/YY HH:MM Set the printer’s built-in clock. The time provided by the clock is used when printing logs and status sheets. Language Japanese Select the language used in the control panel display.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver Problem Solver When a Message is Displayed If one of the following messages is displayed, read and follow the instructions below. Messages What to do Prepare empty waste ink bottle. The waste ink bottle is getting full. Ready a new waste ink bottle. U “Options and Consumable Products” on page 171 Ink Cartridge Error Ink cartridge cannot be recognized. Insert again or replace ink cartridge.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver Messages What to do Unit Matching Error Check combination of Media Feeding Unit and Auto Take-up Reel Unit. Then restart printer. The standard media feeding unit is used only with the standard auto take-up reel unit, the heavy roll media feeding unit only with the heavy roll auto take-up reel unit. If you have mismatched the feeding and take-up reel units, turn the printer off and install the correct equipment.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver Messages What to do Media Sensor Error Loaded media or print out has a problem. Refer to documentation for details. Press the W button to clear the message from the display. The auto menu of Auto Media Adjust, Auto Nozzle Check, and Media Adjust of the media settings are not available in the following media setting or conditions. ❏ Transparent or colored media, or tracing paper is used. ❏ Platen Gap is set to 2.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver Messages What to do Press # and perform Head Maintenance. This message is displayed when regular cleaning has not been performed within the set schedule. If you continue to use the printer without performing regular cleaning, ink drops, nozzle clogging, or print head damage may occur in the printer.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver You cannot print under the network environment. Troubleshooting You cannot print (because the printer does not work) o Ask your network administrator for the network settings. The printer does not turn on. o o Is there any problem with the electrical outlet? The printer has an error. Make sure your outlet works by connecting the power cable for another electric product.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver o Is Circulating ink... displayed on the screen of the control panel? o Perform Head Alignment.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver o The print is not positioned properly on the media. Is Data Width selected for Head Movement? Selecting Data Width for Head Movement in the setup menu increases print speed but may slightly reduce print quality. For better quality results, select Printer Full Width for Head Movement.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver The printed surface is scuffed or soiled. Nozzle clogs cannot be cleared. o o Is cleaning being performed regularly? Is the media too thick or too thin? Check media specifications to confirm that it is compatible with the printer. If you are using a software RIP, contact the manufacturer for information on the settings and media that can be used.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver ❏ Media settings are not configured correctly. Ink drops U “Saving media settings” on page 83 A Check the attachment of the media holding plates If a media holding plate is not installed correctly, media feeding may be disturbed. See the following reference and reattach the media holding plates.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver U “Heating & Drying” on page 89 Stains Due to Head Striking First, configure Heater Temperature as described below. 1) Configure temperature settings for the pre-, platen, and after heaters to a temperature higher than the normal setting temporarily. 2) Perform bidirectional printing and check if the print results have improved.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver C • If you are using SC-S70600 series or SC-S50600 series and adjusting the Media Tension does not resolve the problem, perform the following measure. Adjusting the Heater Temperature The heater temperature setting may be too high. Configure Heater Temperature as described below. 1) 1) Set Feed Speed to Lv1.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver Repeat steps 2 and 3 until print results are im‐ proved in the range up to a setting value of 5. 2) Print and check if creasing is improved. If the creasing of media has improved, media suction was too low. If changing Media Tension does not resolve the problem, return the Media Tension setting to default and perform the following measure.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver o C Is the media too thick or too thin? ❏ Check the media specifications to determine whether it can be used in the printer. Important: c Cease use of the printer if the media holding U “Supported Media” on page 176 ❏ o Move the media holding plates out of the way. plates are deformed. Continued use could damage the pressure rollers or print head.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver U “Loading Media (SC-S70600 series, SC-S50600 series)” on page 37 Important: c Move the print head only after moving the media holding plates out of the way. Contact with deformed media holding plates could damage the print head. E U “Loading Media (SC-S30600 series)” on page 51 Others Raise the media loading lever. Periodical Cleaning is set to Off, but auto cleaning is performed.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Problem Solver The red light is on inside the printer. o This is not a failure. The red light is a light inside the printer. White powdered stains are detected on the sides of the auto take-up reel unit. o See the following sections and clean the part.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Appendix Options and Consumable Products The following options and consumable products are available for use with this printer. (As of November 2014) For the latest information, see the Epson Web site.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Printer model Product SC-S70670 Ink cartridges SC-S70680 SC-S50600 Ink cartridges Ink cartridges Part number Black T7151 Cyan T7152 Magenta T7153 Yellow T7154 Light Cyan T7155 Light Magenta T7156 Light Black T7157 Orange*2 T7158 Orange Plus*2 T7159 White T715A Metallic Silver T715B Black T7161 Cyan T7162 Magenta T7163 Yellow T7164 Light Cyan T7165 Light Magenta T7166 Light Black T7167
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Printer model Product SC-S50610 Ink cartridges SC-S50670 SC-S50680 SC-S30600 SC-S30610 SC-S30670 SC-S30680 Ink cartridges Ink cartridges Ink cartridges Ink cartridges Ink cartridges Ink cartridges Part number Black T6881 Cyan T6882 Magenta T6883 Yellow T6884 White T714A Black T6891 Cyan T6892 Magenta T6893 Yellow T6894 White T715A Black T6901 Cyan T6902 Magenta T6903 Yellow T6904 Whi
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix *1 Epson recommends the use of genuine Epson ink cartridges. Epson cannot guarantee the quality or reliability of nongenuine ink. The use of non-genuine ink may cause damage that is not covered by Epson's warranties, and under certain circumstances, may cause erratic printer behavior. Information about non-genuine ink levels may not be displayed, and use of non-genuine ink is recorded for possible use in service support.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix *1 Not available for purchase in some countries and regions. We recommend BEMCOT M-3II by Asahi Kasei Corporation when purchasing commercial products. *2 Not available for purchase in some countries and regions.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Supported Media Moving and Transporting the Printer The following media can be used with the printer. This section describes how to move and transport the product. Print quality is greatly affected by the type and quality of media used. Choose a media suited to the task at hand. For information on use, refer to the documentation supplied with the media or contact the manufacturer.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix E D Unlock the stand. Release the caster locks on the left and right legs and fully raise the adjusters. Perform Auto Media Adjust in the media settings, and check the print quality. U “Auto Media Adjust” on page 85 Transport Before transporting the printer, contact your dealer or Epson Support. U “Where To Get Help” on page 186 F Move the printer.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Recommended Media Settings To register media settings, refer to the table shown below. For all the item values in the media settings, you can use default setting, except for the item marked by*2 of the SC-S30600 series. SC-S70600 series, SC-S50600 series Adhesive vinyl Transparent film/ Milky white film Banner Canvas 1.5 1.5 1.5 1.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix *1 How to attach counterweights U “Using the Auto Take-up Reel Unit” on page 67 *2 Change the factory default setting value.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Microweave (M/W) Setting and Banding Association Table The tables below show setting examples for the ONYX Graphics software RIP. For the banding status described under "Result", refer to the figure shown below.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Resolution (dpi) 720×720 Number of passes M/W level Result Recommendation 1 Stripe banding less likely 2 Tint uneveness less likely, but stripe banding more likely 3 Stripe banding less likely 4 Tint uneveness less likely, but stripe banding more likely 0 Stripe banding less likely 1 Tint uneveness less likely, but stripe banding more likely 2 Stripe banding less likely 3 Tint uneveness less likely 4 ✓ V
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Resolution (dpi) Number of passes 720×720 4 M/W level Result Recommendation 2 Tint uneveness less likely 3 Stripe banding less likely 0 Tint uneveness less likely 1 Stripe banding less likely 3 Tint uneveness less likely 4 Stripe banding less likely ✓ Vinyl 720×1440 6 ✓ All media (Including Banner/Vinyl) 720×1440 8 182 ✓
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix System Requirements Printer Specifications Power consumption Consult the documentation for your software RIP. SC-S70600 series (total for numbers 1 and 2) Printing: Approx. 800 W Ready mode: Approx. 580 W Specifications Table Sleep mode: Approx. 12 W Power off: 0.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Appendix Printer Specifications Ink Specifications Operation temperature and humidity range Type Special ink cartridges Pigment ink SC-S70600 series: Metallic Silver, Light Black, Black, Cyan, Magenta, Yellow, Orange, Orange Plus, Light Cyan, Light Magenta, White SC-S50600 series: White, Black, Cyan, Magenta, Yellow SC-S30600 series: Black, Cyan, Magenta, Yellow Dimension Storage (minimum) dimensions: 2620 (W) × 963 (D) × 1311 (
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series Appendix EMC FCC part 15 subpart B Class A CAN/CSA-CEI/IEC CISPR 22 Class A AS/NZS CISPR 22 Class A EMC Directive 2004/108/EC EN 55022 Class A EN 55024 EN 61000-3-2 EN 61000-3-3 !Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Where To Get Help Where To Get Help Contacting Epson Support Technical Support Web Site Before Contacting Epson If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting information in your product documentation, contact Epson support services for assistance. If Epson support for your area is not listed below, contact the dealer where you purchased your product.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Where To Get Help Help for Users in North America Help for Users in Taiwan Epson provides the technical support services listed below. Contacts for information, support, and services are: World Wide Web (http:// www.epson.com.tw) Internet Support Visit Epson’s support website at http://epson.com/ support and select your product for solutions to common problems.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Where To Get Help Telephone number Fax number Address 03-5325077 03-5320092 1F., No.9, Ln. 379, Sec. 1, Jingguo Rd., North Dist., Hsinchu City 300, Taiwan 04-23011502 04-23011503 3F., No.30, Dahe Rd., West Dist., Taichung City 40341, Taiwan (R.O.C.) 04-23805000 04-23806000 No.530, Sec. 4, Henan Rd., Nantun Dist., Taichung City 408, Taiwan 05-2784222 05-2784555 No.463, Zhongxiao Rd., East Dist.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Where To Get Help ❏ Sales enquiries and product information ❏ Frequently Asked Questions (FAQ), Sales Enquiries, questions through e-mail ❏ Product usage questions or problems Epson Hotline ❏ Enquiries on repair service and warranty ❏ Sales enquiries and product information Help for Users in Thailand ❏ Technical support Contacts for information, support, and services are: Phone (62) 21-572 4350 World Wide Web (http://www.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Where To Get Help Fax: Help for Users in Hong Kong To obtain technical support as well as other after-sales services, users are welcome to contact Epson Hong Kong Limited.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Where To Get Help Location Telephone number Fax number Pune 020-30286000 / 30286001 /30286002 020-30286000 Ahmedabad 079-26407176 / 77 079-26407347 Helpline For Service, Product info or to order a cartridge 18004250011 (9AM - 9PM) - This is a Toll-free number.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Software License Terms Software License Terms Open Source Software Licenses Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version ("Bonjour Programs"). We provide the source code of the Bonjour Programs pursuant to the Apple Public Source License Version1.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Software License Terms 1.6 "Modifications" mean any addition to, deletion from, and/or change to, the substance and/or structure of the Original Code, any previous Modifications, the combination of Original Code and any previous Modifications, and/ or any respective portions thereof.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Software License Terms 2.3 Distribution of Executable Versions. In addition, if You Externally Deploy Covered Code (Original Code and/or Modifications) in object code, executable form only, You must include a prominent notice, in the code itself as well as in related documentation, stating that Source Code of the Covered Code is available under the terms of this License with information on how and where to obtain such Source Code. 2.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Software License Terms 8. NO WARRANTY OR SUPPORT. The Covered Code may contain in whole or in part pre-release, untested, or not fully tested works. The Covered Code may contain errors that could cause failures or loss of data, and may be incomplete or contain inaccuracies. You expressly acknowledge and agree that use of the Covered Code, or any portion thereof, is at Your sole and entire risk.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Software License Terms (c) automatically without notice from Apple if You, at any time during the term of this License, commence an action for patent infringement against Apple; provided that Apple did not first commence an action for patent infringement against You in that instance. 12.2 Effect of Termination.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Software License Terms EXHIBIT A. "Portions Copyright (c) 1999-2003 Apple Computer, Inc. All Rights Reserved. This file contains Original Code and/or Modifications of Original Code as defined in and that are subject to the Apple Public Source License Version 2.0 (the 'License'). You may not use this file except in compliance with the License. Please obtain a copy of the License at http://www.opensource.apple.
EPSON SC-S70600 series/SC-S50600 series/SC-S30600 series User's Guide Software License Terms 3. Altered versions--including, but not limited to, ports to new operating systems, existing ports with new graphical interfaces, versions with modified or added functionality, and dynamic, shared, or static library versions not from Info-ZIP--must be plainly marked as such and must not be misrepresented as being the original source or, if binaries, compiled from the original source.
