Service manual

Stylus Pro 10600 Field Repair Guide 7/29/04
Control Panel Map Page 5.
Maintenance Mode 1 Options
1. HEX DUMP MODE: - Prints data in Hexadecimal format for troubleshooting control codes.
2. LANGUAGE MODE: - Determines the language used for the LCD Display. [English, Potuguese, Spanish, German, Italian, French]
3. UNITS : - Set to Metric of Inches/Feet
4. Parallel I/F: - Sets the parallel interface mode. [Compatible or ECP]
5. IEEE1284.4 MODE: - [On or Off]
6. INTERNAL JOB OOUNT: - [On or Off]
7. AUTO NOZZLE CHECK MODE: - [On or Off]
8.SSCL B/C : - Super Strong Cleaning for Black/Cyan
9.SSCL LC/LM : - Super Strong Cleaning for Light Cyan / Light Magenta
10.SSCL M/Y: - Super Strong Cleaning for Magenta/Yellow
11. MW7=A - . Range is A thru C.
12. MW7 BALANCE MODE: - Adjust MW7 feeding in mode B when printing. [-30 to +30]
13. MW1 SELECT MODE: - Used to set the M/W value [1 to 10] 720 mode
14. MW2 SELECT MODE: - Used to set the M/W value [1 to 7] 1440 mode
15. DEFAULT PANEL: - Used to reset the panel to default settings
16. CARTRIDGE INFORMATION MENU: - Gives details about ink cartridges (type and usage).
17. SN Menu - For Factory Use only.
Paper Feed] + or [Paper Feed -] to change value. Use [Cut/Eject] to Confirm, Save or Execute the item/value.
1. Use the [Paper Source] to move
down the menu.
2. Pressing the [Enter] button will move
you into the sub menu.
3. Pressing the [Pause] button will
move you back one menu item.
Maintenance Mode 2 Options
1. View Counters Menu
2. Clear Counters
3. Service Config.
4. FACTORY USE ONLY!
While in this menu option, you are capable of viewing all the counter information for the following components:
Cutter, Cutter Total, Total Pages, Waste Ink A/B, CR Motor, CR Motor Total, PF Motor, Head K, Head C, Head M, Head LC, Head LM,
Head Y, Cleaner.
While in this menu option, you are capable of initializing the following items:
RTC, Cutter, CR Motor, CR Total, PF Motor, Head, Cleaner, Total Pages, Ink, Waste Ink Tank, Flushing Box, NVRAM, All.
1 - 6 . TABLES XX1 to XX5, XXS. - Used to set the paper feed adjustment mode for tables 1 through 5.
7. NZL_AY: - [0 to 45
8. NZL_HC2: - [0 to 45
9. NZL_HCD: - [0 to 45
10. NZL_PPI: - [0 to 45
11. [NPD] - 1 (Pigment), 2 (Dye), *3 (UltraChrome),0 (Neutral).
12.ED Mode - *X (all CSIC info is read), O (all CSIC info is read except market), N (no CSIC info is read)
13. FLBL DET: - [ON or OFF]
The following menus are for factory use: - P3 DUMP, MENU E, MENU R, MENU S, MENU C, MENU A, MENU B, MENU P, MENU M, MENU
O, MENU F, MENU N, MENU X,
1. Use the [SelecType] to move down
the menu.
2. Pressing the [Paper Source] button
will move you into the sub menu.
3. Pressing the [SelecType] button will
move you back one menu item.