Specifications
Table Of Contents
- 1 Introduction
- 2 S5U1C63000H6 Package
- 3 Connection
- 4 Getting Started
- 5 Operations and Functions of the S5U1C63000H6
- 5.1 Outline of Operation
- 5.2 Break Function
- 5.3 Monitoring Terminals
- 5.4 Display During Execution and During Break
- 5.5 Break Commands
- 5.6 Target Interrupt and Break
- 5.7 Trace Function
- 5.8 Trace Mode
- 5.9 Trace Trigger Point
- 5.10 Coverage Function
- 5.11 Measurement of Execution Time
- 5.12 Self-Diagnostic Function
- 5.13 Restrictions on Emulation
- 6 LCD Driver
- 7 Notes on Use
- 8 Maintenance and Warranty
- 9 Troubleshooting
2 S5U1C63000H6 PACKAGE
4
EPSON
S5U1C63000H6 MANUAL
(S1C63 Family In-Circuit Emulator)
2.4 Specifications of the Operation Panels
Figure 2.4.1 shows the external view of the panels.
TRGOUT
STOPOUT
TRC IN
BRK IN
GND
DIAG
OFF ON
S5U1C63000H6 EPSON
SLP/HLT
EMU
POWER
LC2 LC1
(Front view)
POWER
CB
FG
DC 12V
IO
(Rear view)
Figure 2.4.1 External View of S5U1C63000H6 Panels
Table 2.4.1 shows the function of each component on the panels.
Table 2.4.1 Function List of Components
No. Position Symbol Name Function
1 Front panel POWER Power on LED This green LED lights upon power-on of the S5U1C63000H6.
2 Front panel EMU Emulation LED This red LED lights when the target program is in running status.
3 Front panel SLP/HLT SLEEP/HALT LED This yellow LED lights when the S1C63000 CPU executes the
HALT or SLP instruction. This LED also lights when the peripheral
circuit board has not been installed.
4 Front panel DIAG Self-diagnostic
select switch
This switch is used to select whether the S5U1C63000H6 self-
diagnosis at startup of the debugger will be executed or not.
5 Front panel TRGOUT Trace-trigger
output terminal
Upon coincidence of trigger conditions with a tracing trigger point,
a pulse is output from this terminal.
6 Front panel STOPOUT SLEEP/HALT
status output
terminal
When the S1C63000 CPU is in HALT or SLEEP status, a low level
signal is output from this terminal. This is used to measure execu-
tion rate of the CPU. Also this terminal goes low in break status.
7 Front panel TRCIN Trace input
terminal
Trace information will be stored in the trace memory by connecting
a signal of the target system to this terminal.
8 Front panel BRKIN Break input
terminal
A running program enters break status by input a low level signal
to this terminal from the target system.
9 Front panel GND Ground terminal When monitoring the above terminals with an oscilloscope, con-
nect the GND line of the oscilloscope to this terminal. This is also
used as a GND when inputting signals to the above terminals.
10 Front panel LC1, LC2 LCD connectors These connectors are used to connect an LCD panel.
11 Rear panel POWER Power switch Turns the S5U1C63000H6 power on and off.
12 Rear panel DC12V DC input connector This connector is used to connect the DC cable of the AC adapter
for S5U1C63000H6. Be sure to use the AC adapter included in
this package.
13 Rear panel CB Circuit breaker The breaker cuts off the power of this system (peripheral board,
add-on board and target board) at consumption current of 3 A or
more. A small staff of breaker comes up at the shut-off. The staff
should be at the recessed position for normal operating status.
14 Rear panel USB connector This USB cable connector is used to interface with the host com-
puter.
15 Rear panel FG Frame ground This is the frame ground terminal. We recommend to connect this
terminal to the ground line.