MF985-03 CMOS 4-BIT SINGLE CHIP MICROCOMPUTER S5U1C62000H Manual (S1C60/62 Family In-Circuit Emulator)
NOTICE No part of this material may be reproduced or duplicated in any form or by any means without the written permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.
The information of the product number change Starting April 1, 2001, the product number will be changed as listed below. To order from April 1, 2001 please use the new product number. For further information, please contact Epson sales representative.
CONTENTS CONTENTS CHAPTER 1 INTRODUCTION ____________________________________________ 1 CHAPTER 2 S5U1C62000H PACKAGE SPECIFICATIONS _______________________ 2 2.1 2.2 2.3 2.4 2.5 CHAPTER List of Components ....................................................................................... 2 Component Specifications ............................................................................ 3 Operating Conditions ...................................................................................
CHAPTER 1: INTRODUCTION CHAPTER 1 INTRODUCTION This manual describes how to operate, maintain and connect the in-circuit emulator S5U1C62000H. Refer to the "S5U1C62000A Manual" for details of the S5U1C62000H functions and usage of the commands. 3.2A FUSE ∗ The name 'ICE62R' on the development tool is the old name of the product.
CHAPTER 2: S5U1C62000H PACKAGE SPECIFICATIONS CHAPTER 2 S5U1C62000H PACKAGE SPECIFICATIONS 2.1 List of Components Figure 2.1.1 shows the contents of the S5U1C62000H package. After unpacking, check to see that the following components are all provided. (1) S5U1C62000H (main unit) ........................................................................................ one (2) Evaluation Board interface cables ..........................................................................
CHAPTER 2: S5U1C62000H PACKAGE SPECIFICATIONS 2.2 Component Specifications Table 2.2.1 shows the specifications of the components included in the S5U1C62000H Package. Table 2.2.1 Specifications of S5U1C62000H components No.
CHAPTER 2: S5U1C62000H PACKAGE SPECIFICATIONS 2.4 Control Unit Specifications This section describes the operation of the switches and other control units on the S5U1C62000H. Figure 2.4.1 shows the external view of the S5U1C62000H. 9 8 14 3.2A FUSE 15 1 13 6 5 4 7 2 3 12 10 11 Fig. 2.4.1 S5U1C62000H external view Table 2.4.1 lists the functions of the control units. Table 2.4.1 Functions of S5U1C62000H control unit No.
CHAPTER 2: S5U1C62000H PACKAGE SPECIFICATIONS 2.5 Dip Switch Setting The S5U1C62000H can be controlled by a host computer (NEC PC-98 Series, IBM PC/AT or its compatible machine). To communicate between the S5U1C62000H and the host computer, it is necessary to set the same baud rate and transfer data specifications in both. For the S5U1C62000H, the baud rate can be set by a dip switch. Figure 2.5.1 shows the settings with the dip switch.
CHAPTER 3: CONNECTIONS CHAPTER 3 CONNECTIONS This chapter describes connecting the S5U1C62000H with the host computer and the Evaluation Board (S5U1C62xxxE). 3.1 Connecting AC Adapter The S5U1C62000H package includes a dedicated AC adapter and an AC power cable (bipolar, with ground). Connect the DC cable of the AC adapter to the DC IN terminal (5 V DC input terminal) of the S5U1C62000H, and the AC power cable to the AC inlet of the AC adapter.
CHAPTER 3: CONNECTIONS 3.2 Connecting Host Computer Figure 3.2.1 shows the external view of the 9-pin/9-pin RS232C cable connector and Table 3.2.1 shows the signal specifications. 5 2 1 A 9 6 Viewed from side A 9-pin/9-pin RS232C cable connector Fig. 3.2.1 9-pin/9-pin RS232C cable connector Table 3.2.1 Signal specifications Pin No.
CHAPTER 3: CONNECTIONS 3.3 Connecting Evaluation Board Figure 3.3.1 shows the external view of the Evaluation Board interface cable. 2 1 2 1 50 49 50 49 S5U1C62000H side Evaluation Board side Fig. 3.3.1 External view of Evaluation Board interface cable The Evaluation Board interface cables are connected to the F1 and F5 connectors of the S5U1C62000H with its projections (to prevent wrong insertion) inside (cable side).
CHAPTER 4: PRECAUTIONS CHAPTER 4 PRECAUTIONS To use S5U1C62000H properly, observe the following precautions: • Turn off the S5U1C62000H and the host computer before connecting or removing the cables. Especially take care of the connection or removal of the Evaluation Board interface cable. Since the interface is CMOS level, connection/removal when the S5U1C62000H is on may break internal integrated circuits permanently. • Do not turn the S5U1C62000H on again immediately after power-off.
CHAPTER 5: MAINTENANCE AND WARRANTY CHAPTER 5 MAINTENANCE AND WARRANTY 5.1 Diagnostic Test The S5U1C62000H performs a self diagnostic test after power on. The following messages show that the hardware has no problem. * ICE POWER ON RESET * * DIAGNOSTIC TEST OK * ...(1) # When an error occurs in the self diagnostic test, an error message appears instead of the message (1) below.
CHAPTER 6: TROUBLESHOOTING CHAPTER 6 TROUBLESHOOTING This chapter summarizes possible errors related with system operation, along with possible solutions for them. • Debugger cannot be loaded. Be sure that the host computer has a satisfactory memory capacity. (See "S5U1C62000A Manual".) Be sure that the software is loaded in a proper operating system. (See "S5U1C62000A Manual".) • Debugger can be loaded, without prompt for command entry. Be sure that the RS232C cable is connected properly.
International Sales Operations AMERICA ASIA EPSON ELECTRONICS AMERICA, INC. EPSON (CHINA) CO., LTD. - HEADQUARTERS - 28F, Beijing Silver Tower 2# North RD DongSanHuan ChaoYang District, Beijing, CHINA Phone: 64106655 Fax: 64107319 1960 E. Grand Avenue EI Segundo, CA 90245, U.S.A. Phone: +1-310-955-5300 Fax: +1-310-955-5400 SHANGHAI BRANCH 4F, Bldg., 27, No.
S5U1C62000H Manual (S1C60/62 Family In-Circuit Emulator) ELECTRONIC DEVICES MARKETING DIVISION EPSON Electronic Devices Website http://www.epson.co.
