SERVICE MANUAL Color Inkjet Printer EPSON Stylus Photo R260/R265/R270 R360/R380/R390 SEIJ06001
PRECAUTIONS Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) damage to equipment. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by DANGER Headings. WARNING Signals a precaution which, if ignored, could result in damage to equipment.
About This Manual This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. manuals4you.com Manual Configuration This manual consists of six chapters and Appendix. CHAPTER 1.PRODUCT DESCRIPTIONS Provides a general overview and specifications of the product.
Revision Status Revision Date of Issue A August 10, 2006 B September 12, 2006 Description First Release Chapter 1 1.7.5 Dimensions (p.22) are changed. Chapter 2 2.2.1 Main Features (p.26) of C658Main Board is modified. 2.2.3 Circuit Block Diagram (p.28): error correction Chapter 3 3.2.1 Error Indication Method (p.33): EPSON Status Monitor 3 error messages are changed. 3.3.1 Troubleshooting Problems with Error Messages (p.36) is modified. (CR Encoder) 3.4.4 Problems with Interfaces (p.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B CONTENTS Chapter 1 Product description Chapter 3 Troubleshooting 1.1 Overview .............................................................................................................. 9 1.1.1 Differences between R260/265/270 and R360/380/390............................ 9 1.2 Basic Specifications............................................................................................ 10 1.2.1 Printing ...................................
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2.8 Right Front Housing / Left Front Housing .............................................. 72 4.2.9 Front Housing .......................................................................................... 73 4.3 Removing Control Boards.................................................................................. 76 4.3.1 Removing the USB Board (R260/R265/R270 only) ............................... 76 4.3.2 Removing the Main Board Unit ....
CHAPTER 1 PRODUCT DESCRIPTION
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.1 Overview 1.1.1 Differences between R260/265/270 and R360/380/390 Stylus Photo R260/R265/R270 and R360/R380/R390 are A4 home-use photo printers. Besides printing on papers, printing directly on CDs/DVDs are available.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.2 Basic Specifications Paper Feeding Table 1-3. Paper Feeding Specifications 1.2.1 Printing Item Basic Specifications Table 1-2. Basic Specifications Item Description Print method On-demand inkjet printer Print head Black ink: 90 nozzles Color ink: 90 nozzles x 5 colors (C, M, Y, LC, LM) Printing direction Bi-directional shortest-distance printing with logic seeking Resolution 5760 x 1440 dpi at max.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.2.2 Interfaces USB Host Port Table 1-6. USB Host Port Specifications The printers are equipped with the following interfaces.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.2.2.3 Memory Card Slot (R360/R380/R390 only) Table 1-8. Compatible Card Types by the Card Slot Priority Slot 1 CF Type II 2 xD-Picture card Memory Stick/ Memory Stick PRO Compatible Card Type Compact Flash Standard CF+ and CompactFlash Specification Revision 2.0 compliant Memory card only xD-Picture card xD-Picture Card Specification Version 1.20 compliant Supports Type M/H Memory Stick MemoryStick Standard version 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 1.3 Standalone Printing (R360/R380/R390 only) The Stylus Photo R360/R380/R390 offers Direct-Print function that allows the user to print directly from a memory card without using a PC. Besides printing still images, printing frames of a movie file is also available. The Memory Card button on the operation panel displays menus for printing both still and movie images. 1.3.1 Direct Print of Still Images Revision B PRINT Image Framer (P.I.F.) file (*.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 not guaranteed which files are selected when the number of files is 1000 or more. When photo data files to which a camera has assigned numbers over 999 are specified to be printed, they can be printed unless the total number of files exceeds 999. File Sort The printer sorts all the photo data files in a memory card using their full pathnames (such as “\DCIM\100EPSON\EPSN0000.JPG”) and assigns numbers to them.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.4 Backup Function (R360/R380/R390 only) Available media type Table 1-10. Available Media Type Stylus Photo R360/R380/R390 allows the user to easily make a backup of his/her memory card without using a computer. Furthermore, photos in a backup copy can be printed directly from the printer. External Device Backup entire data in a medium (CF, Smart Media, Memory Stick, SD, xDPicture Card).
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Writing Format for CD-R Media Backup Restrictions Writing to CD-R media is made in multisession type (Model 1) and ISO-9660 (Joliet)compliant format. Files or folders whose name includes an unsupported character code or is too long (file/ folder name must be less than 8 characters, and the extensions must be less than 3 characters), the names are automatically changed as explained below. File name: EPSONXXX.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Backup-related errors Table 1-11. Backup-related Errors Error Description Message Remedy Backup error (no external connection) No external device is detected when a backup is attempted. External device is not connected or media is not inserted. Connect an external device. Backup canceled.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B The table below lists the error codes controlled by the printer firmware. Table 1-12. Backup Error FW Control Code List Meaning Code Code Meaning 1.5 CD/DVD Print (R360/R380/R390 only) Stylus Photo R360/R380/R390 provides the Print CD/DVD button that allows the user to easily access the menus for printing on CDs/DVDs and their jackets. The menus include the following layout options.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.6 Operation Panel Table 1-13. R360/R380/R390 Button Functions Button 1.6.1 Operation Panel 5 Print CD/DVD 6 Setup Displays various setup menus such as maintenance menus (Change Ink Cartridge, Head Cleaning, Nozzle Check, etc.), Backup Memory Card menu and option setting menus (Bluetooth settings, etc.). 7 OK Accepts the selection or changed settings. 8 Back Undoes the last action made by the operation panel.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Stylus Photo R260/R265/R270 Operation Panel Power LED Ink LED Paper LED Revision B 1.6.2 Indicator (LED) Stylus Photo R360/R380/R390 These models are equipped with a 3.5inch color LCD (320x240) and one Power LED and two Mode LEDs on their control panel. The LCD displays menus for selecting function, making settings, and a status of the printer. • Power LED (green): Lights during the printer is powered.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.7 Specifications Common to the Models 1.7.2 Environmental Condition Table 1-17. Environmental Condition 1.7.1 Electric Specifications Item Table 1-15. Electric Specifications Item 100-120V model Temperature*1 220-240V model Humidity (no condensation)*1 Rated voltage 100-120 VAC 220-240 VAC Impact resistance Input voltage range 90 - 132 VAC 198-264 VAC Vibration resistance 0.6 A R260/265/270: max. 0.9A R360/380/390: max. 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 1.7.5 Dimensions Table 1-18. Dimensions Item Weight With covers closed Dimensions (W x D x H) With covers opened Product description R260/R265/R270 R360/R380/R390 6.2 kg 6.
CHAPTER 2 OPERATING PRINCIPLES
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 2.1 Overview Table 2-2. Main Control Boards Board Function This chapter describes the operating principles of the printer mechanism and electric circuit boards of Stylus Photo R260/R265/R270 and R360/R380/R390. Card Board Located on the Middle Housing. Incorporates memory card slots, (R360/R380/R390 only) USB HOST interface, and an infrared communication circuit. 2.1.1 Printer Mechanism USB Board Located on the Middle Housing.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 2.1.2 Motors & Sensors Table 2-3. List of Motors & Sensors No. 1 Motor/Sensor Name APG Sensor Function PF Encoder Sensor Printhead F3-MACH head (6 colors x 90 nozzles) CR motor Type: DC motor Drive voltage: 42V DC ± 5% (voltage applied to the driver) Coil resistance: 22.7Ω ± 10% Inductance: 17.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 2.2 Electrical Circuit Operating Principles Features of C653Main Board (R260/R265/R270) The electric circuits of the Stylus Photo R260/R265/R270 and R360/R380/R390 consist of the following boards. Table 2-4.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 2.2.2 Components of Control Boards Table 2-5. Components of Control Boards Incorporated Components Board Name R360/R380/R390 R260/R265/R270 Logic circuit Logic circuit (ASIC incorporated in the CPU (ASIC incorporated in the CPU core, Flash ROM x 1, SDRAM x 1) core, Flash ROM x 2, SDRAM x 1, DDR1 x 1) System Interface circuit (USB2.0 DEVICE, USB2.0 HOST) RTC circuit Panel interface 3.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 2.2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Flash-ROM (IC1) Motor Driver (IC8) SDRAM (IC2) RTC (IC3) Serial Flash-ROM (IC4) CPU-ASIC (IC5) CN14 CR Motor CN13 PF Motor CN8 PF Encoder Sensor CN7 APG Sensor CN6 PE Sensor CN4 CDR Guide Sensor CDR Tray Sensor C653 Panel Board CN5 CN10 USB HOST (CN2) Head Driver (IC7) Q2, Q5, Q6, Q7 CN12 USB (CN1) CN16 C653 PSB/PSE Board Printhead CN11 CN3 CR Encoder Sensor PW Sensor CN15 C653 Head Board Figure 2-4.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 2.3 Banding Reduction System (BRS) / Paper Feed Amount Profile Correction (PFP) Overview In order to ensure high print quality and high print speed, this product incorporates the Banding Reduction System (BRS) and Paper Feed Profile (PFP) Correction system. The overview of them is described in the table below. Table 2-6.
CHAPTER 3 TROUBLESHOOTING
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.1 Overview 3.1.1 Troubleshooting on Motors and Sensors This chapter provides how to troubleshoot problems analyzing the cause based on the error messages displayed on the printer and the observed symptom. Identify and troubleshoot the problem referring to the tables on the following pages. When some parts need to be replaced, make sure to follow the procedure given in Chapter 4 and carry out required adjustments.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.2 Error/Warning Indications • Message box on the window of "EPSON Status Monitor 3" This section describes how the printer indicates an error/warning status with the LCD and LEDs, or on the screen of the printer driver when a problem arises during various operations; power-on sequence, paper feeding, ink drawing, printing, and so on. 3.2.1 Error Indication Method Message Box The Stylus Photo R360/R380/R390 are equipped with a LCD.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-4. List of Error Messages R360/R380/R390 Error Name Messages on the LCD Communication error R260/R265/R270 LED Indications Power Paper - Maintenance request error Waste ink pad in the printer is saturated. Contact your dealer to replace it. Off Fatal error Printer error. Please see your documentation. Ink cartridge detection error Ink cartridges cannot be recognized. Make sure ink cartridges are correctly installed.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-4. List of Error Messages R360/R380/R390 Error Name No paper error CDR Tray error Messages on the LCD Paper out. Load paper and press the Start button. The CD/DVD tray is set incorrectly. Please correct, then press the Start button. R260/R265/R270 LED Indications Power Paper CDR Guide error The CD/DVD guide is in the CD/DVD position. Close the CD/DVD guide.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.3 Troubleshooting by Error Message The following tables provide troubleshooting procedure for each error message indicated by the LCD or STM3 screen. When some parts need to be replaced or repaired, make sure to follow the procedure given in Chapter 4 and carry out required adjustments. 3.3.1 Troubleshooting Problems with Error Messages Table 3-5.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-6. Troubleshooting for Fatal Error Occurrence Timing Symptom Failed Part CR Motor Main Frame Check Point Remedy 1. Is the CR motor cable not connected to the Main 1. Connect the cable correctly. Board? R360/R380/R390 Main Board: CN14 R260/R265/R270 Main Board: CN14 4.3.2 "Removing the Main Board Unit"(p.78) 2. Is there a malfunction of the CR motor? 2. Replace the CR motor. 4.5.8 "CR Motor"(p.99) 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-6. Troubleshooting for Fatal Error Occurrence Timing Symptom Failed Part Check Point Remedy 1. Is the Compression spring 2.36 of the Change Lever disengaged? 1. Replace the ASF Unit. For the R360/R380/ R390, replace the Change Lever. ASF Unit 4.5.11 "ASF Unit"(p.104) CR Motor At power-on • The CR Unit hits against the Change Lever which has come down toward the front of the printer.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-6. Troubleshooting for Fatal Error Occurrence Timing At power-on Symptom • The CR Unit hits against the Change Lever which has come down toward the front of the printer. • The error appears after the PF roller makes quick one-turn Failed Part Check Point Remedy 1. Is the PF Scale not moving freely, centered between the sides of PF encoder sensor? 1. Install the PF Scale or PF encoder correctly. 2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-7. Troubleshooting for Ink Cartridge Detection Error/ Ink Cover Open Error/ Cartridge Empty Error Occurrence Timing Symptom Failed Part Check Point Remedy 1. Is the memory chip on the cartridge chipped or broken? Reference 1. Replace the ink cartridge. Ink Cartridge Ink Cartridge - Memory Chip 1. Is the Head FFC not connected to the Head Board and the Main Board? 1. Connect the Head FFC to the Head Board and the Main Board.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-8. Troubleshooting for Paper Jam Error Occurrence Timing Symptom Failed Part ASF Unit Even though the printer performs paper feeding operation, the paper is not fed into the printer. Check Point Remedy 1. Is the ASF Unit installed incorrectly? 1. Install the ASF Unit correctly. 2. Is the Paper Return Lever not moving properly during the feeding operation? 2. Install the Paper Return Lever and the Torsion Spring 6.45 correctly.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-8. Troubleshooting for Paper Jam Error Occurrence Timing Symptom Failed Part Check Point 3. Is the Torsion Spring 0.22 detached or attached incorrectly? Remedy Reference 3. Install the PE Sensor Lever and the Torsion Spring 0.22 correctly. PE Sensor Lever Paper is fed into the printer, but ejected at once without any printing operation. PE Sensor 4.5.14 "Front Paper Guide Assy/APG Sensor Assy"(p.109) Torsion Spring 0.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-9. Troubleshooting for No Paper Error Occurrence Timing Symptom Failed Part The LD Roller rotates normally to feed paper, but the Hopper does not move. ASF Assy The LD Roller rotates normally, but paper is not fed into the printer. Check Point Remedy 1. Is the Hopper not moving properly during the feeding operation? 1. Attach the Compression Spring 2.51 correctly to the ASF Frame and the Hopper. 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-9. Troubleshooting for No Paper Error Occurrence Timing Symptom Failed Part Check Point Remedy 3. Is the clutch damaged? Reference 3. Replace the ASF Unit. ASF LD Roller The PF Motor drive force is not transmitted to the LD Roller. ASF Assy Clutch 4. Is the Compression Spring 2.36 of the Change Lever detached? Any time 4. Replace the ASF Unit. For R360/R380/ R390, replace the Change Lever. 4.5.11 "ASF Unit"(p.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-10. Troubleshooting for CDR Tray Error Occurrence Timing Symptom Failed Part Check Point Remedy 1. Has the part of the CDR Tray that contacts with the CDR Tray Sensor become cracked? Contact point Reference 1. Replace the CDR Tray. CDR Tray CDR Tray - The CDR Tray is set to the printer, but the error occurs. 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-10. Troubleshooting for CDR Tray Error Occurrence Timing Symptom Failed Part Check Point Remedy 1. Is there any paper dust or ink stain on the PW Sensor? Reference 1. Clean off any dirt on the PW Sensor. Cable 4.5.12 "CR Unit"(p.105) PW Sensor When printing on CDs/DVDs CR Encoder Board The CDR Tray center detection sequence is interrupted, and the tray is ejected. PW Senor Main Board Troubleshooting PW Sensor 2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-11. Troubleshooting for CDR Guide Error Occurrence Timing Symptom Failed Part Check Point 1. Is the CDR Guide Detection Assy cable not connected to the Main Board? CDR Guide Detection ASSY When printing on CDs/DVDs The CDR Guide is set correctly, but the error occurs. CDR Guide Lever Main Board Troubleshooting Remedy 1. Connect the cable to the Main Board.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.4 Troubleshooting by Symptom 3.4.1 Problems in Printing Operation This section provides how to troubleshoot the possible problems on the printer mechanism. No error message appears for most of the troubles described here. In the following tables, find the symptom you face and follow the troubleshooting procedure given in the table. Paper Feeding Problems Symptom Possible Cause Table 3-12.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-12. Troubleshooting Paper Feeding Problems Symptom Possible Cause Check Point Remedy Is the Extension Spring 1.98 at backside of the Retard Roller detached? Attach the Extension Spring correctly. Retard Roller Multiple sheets A malfunction of the Retard are fed at a time. Roller Extension Spring ASF Is the Retard Roller detached? INstall the Retard Roller correctly. Problems with ejecting paper Table 3-13.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Printer initialization operation is aborted Table 3-15. Troubleshooting Initialization Stop Problems Symptom Possible Cause Remedy Improper installation of the EJ Frame Are the tabs of the EJ Frame disengaged? Reinstall the EJ Frame correctly. A malfunction of the CR Motor Is the CR Motor cable/connector disconnected? Connect the CR Motor cable/connector properly.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Print quality problems Table 3-16. Troubleshooting Print Quality Problems Symptom Printed image has missing colors, and the missed colors are always same. Missing dots appear sometimes. White streak / abnormal discharge Vertical lines are misaligned. Possible Cause Check Point Remedy Dirt on the Printhead. Run a cleaning cycle and make a test print. Repeat the operation several times.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 3-16. Troubleshooting Print Quality Problems Symptom Possible Cause Dirt on the CR shaft Check Point Is there any dirt on the CR shaft? Clean off any dirt on the CR shaft surface with a dry soft cloth. Is there any dirt on the PF Roller? Clean the PF Roller surface with a soft brush carefully so as not scratch it. Is the PF Roller damaged? Replace the PF Roller.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.4.2 Power Problems The printer does not work at all after power-on. LEDs do not light up. Table 3-17. Troubleshooting Power Problems Possible Cause Check Point Remedy Power code failure Replace the power code with a new one. Does the printer work normally? The power code is defective. Use the new one.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Printing cannot be made properly (printed image is faint, blurry, smeared, or etc.) Table 3-19. Troubleshooting Printing Problems Symptom The carriage moves normally, but the printed image is abnormal. Possible Cause Check Point Remedy Ink cartridge failure Replace the ink cartridge with a new one, and make a test print. The printed pattern has no missing dots? The cartridge is defective. Use the new one.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3.4.4 Problems with Interfaces This section provides how to troubleshoot problems on the USB interface and memory card slot. USB interface error Table 3-21. Troubleshooting USB Connection Errors Possible Cause Check Point Remedy The printer driver has not been installed correctly. On the Windows PC, go to My Computer, Properties, Hardware, Device Manager.
CHAPTER 4 DISASSEMBLY/ASSEMBLY
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.1 Overview W A R N IN G This section describes procedures for disassembling the main components of the Stylus Photo R260/R265/R270 and R360/R380/R390 Unless otherwise specified, disassembled units or components can be reassembled by reversing the disassembly procedure. Procedures which, if not strictly observed, could result in personal injury are described under the heading “WARNING”.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.1.2 Tools Table 4-2. List of Screw Types Use only specified tools to avoid damaging the printer. Table 4-1. List of Tools Tool Supplier* Part No. Phillips Screw Driver (No.1) EPSON 1080530 Phillips Screw Driver (No.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.1.4 Work Completion Checklist Table 4-4. Work Completion Checklist Whenever the printer is serviced, use the checklist shown below to confirm all work is completed properly and the printer is ready to be returned to the user. Classification Packing Make sure to always check the maintenance counter before disassembling the printer.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B PROTECTION FOR TRANSPORTATION Before packing the printer to be returned to the user, attach several pieces of strong tape and vinyl sheet to the specified points to prevent damaging the printer during transportation. Securing the Carriage (tape: 180mm x 1 pc., fold one end by 5mm) 1. Attach 40mm-length portion of the tape (not folded side) to the left side of the carriage aligning the tape’s corner with the carriage’s ribs as shown below. 2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Protecting the exterior parts from scratches and scuff marks Have a commercially available 250cm-width x 100cm-length vinyl sheet to cover the exterior parts, and secure the sheet with 60mm-length strong tape (fold one end by 5mm). Front Cover Fold the vinyl sheet in half, and insert the folded sheet between the Stacker Assy and the Front Cover with the folded side facing front side of the printer.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.1.7 How to Unlock the Carriage 4.1.8 Sharp Metal Edges (Danger!) Unlocking the carriage is required for disassembly of some parts or components. Carry out any of the following operations to unlock the carriage and move the carriage to other than its home position. C A U T IO N C A U T IO N Be extremely careful not to damage the EJ Roller gear. Extra care must be taken to avoid injury from sharp metal edges.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.1.9 Differences in Disassembly Procedure by Model The table below lists the differences in disassembly procedure between the Stylus Photo R260/R265/R270 and R360/R380/R390. For more details on each procedure, refer to the page given in the Reference column. Figure 4-10.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.1.10 Disassembly/Assembly Procedures The flowchart below lists the step-by-step disassembly procedures. When disassembling each unit, refer to the page number shown in the figure. START Paper Support (p.65) Printer Cover (p.65) Front Cover (p.66) Disassembling the Panel Unit (p.83) Removing the Printer Mechanism (p.87) Right Housing / Left Housing / USB Housing (p.66) Upper Housing (p.68) Panel Unit (p.69) CR Scale (p.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2 Removing Exterior Parts/Components 4.2.2 Printer Cover Parts/Components need to be removed in advance: Nothing 4.2.1 Paper Support Removal procedure Parts/Components need to be removed in advance: Nothing 1. 2. Removal procedure 1. 2. Open the Paper Support. Disengage the right shaft of the Paper Support from the bushing of the ASF Unit by pushing the bushing outward.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2.3 Front Cover 4.2.4 Right Housing / Left Housing / USB Housing Parts/Components need to be removed in advance: Nothing Parts/Components need to be removed in advance: Nothing Removal procedure Removal procedure 1. 2. 3. Open the Front Cover. Raise the CDR Guide Lever to lower the Stacker. While pushing , disengage the left and right positioning holes of the Front Cover in that order, and remove the Front Cover. 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Removing the USB Housing 1. Push part to disengage the hook and slide the USB Housing upward to remove it. [Left side] Removal Direction Hook : Tab Figure 4-18. Disengaging the Hook and Tabs 4. USB Housing Remove the Left Housing in the same manner. Before screwing the Right Housing and Left Housing, make sure the two hooks on each housing shown below are properly inserted into the holes of the Upper Housing.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2.5 Upper Housing Parts/Components need to be removed in advance Paper Support / Printer Cover / Front Cover / Right Housing / Left Housing / USB Housing Removal procedure 1. Be careful not to let the cables get caught under the Upper Housing at the position indicated with in Fig.4-22. Tighten the screws in the order given in Fig.4-21.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2.6 Panel Unit 2. Parts/Components need to be removed in advance Paper Support / Printer Cover / Front Cover / Right Housing / Left Housing / USB Housing / Upper Housing 3. Slide the Panel while pulling it upwards and disengage the two hooks. If the hooks do not disengage, insert a flathead screw driver into the hole of the Front Housing positioning rib from the backside of the panel, to disengage the two hooks ( ).
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2.7 EMI Frame / Waste Ink Tray 1. Parts/Components need to be removed in advance Paper Support / Printer Cover / Front Cover / Right Housing / Left Housing / USB Housing / Upper Housing / Panel Unit Removal procedure C A U T IO N C H E C K P O IN T 1. 2. 2. 3. Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. •“4.1.8 Sharp Metal Edges (Danger!) (p.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Waste Ink Tray Removal C A U T IO N 1. When removing the Waste Ink Tray, take extra care not to spill ink and contaminate the printer and surroundings. Do not pull the Waste Ink Tray too much to remove it, as it is connected to the Ink System with the Waste Ink Tube. Extra care must be exercised not to scratch or damage the Waste Ink Tube. The EJ Frame Spring of the EJ Frame Assy is located beneath the Waste Ink Tray. ( in Fig.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Wipe off any ink on the joint portion of the Waste Ink Tube before reconnecting the tube. Ink on the joint portion makes the tube likely to get disconnected. Insert the Waste Ink Tube until its leading edge reaches the point where the shaft of the Waste Ink Tray starts to widen as shown below. Edge of the Tube 4.2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. 4. Revision B With a flathead screwdriver or similar tool, disengage the two tabs on the inner left and right sides. From the bottom side of the Printer, insert a flathead screw driver into the hole of the Lower Housing to disengage the two tabs. (With R260/R265/R270, the tabs can be disengaged from the upper side of the Middle Housing.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 1. 2. 3. Revision B Install the Front Housing following the steps below Install the Slot Cover. (R360/R380/R390 only) With the two hooks on the inner bottom, insert the right followed by the left. Push the two parts and insert the hooks firmly. 7. While pressing the Front Housing with your thumb holding the Middle Housing with your other fingers as shown below, secure the screw (3) on the bottom left.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.3 Removing Control Boards 5. 4.3.1 Removing the USB Board (R260/R265/R270 only) USB Shield Plate Remove the USB Shield Plate and the USB Board. Parts/Components need to be removed in advance All exterior parts/components CN1 USB Board removal C H E C K P O IN T R260/R265/R270 are equipped with a USB Board. Remove the USB Board before removing the Main Board. Refer to R260/ R265/R270 & R360/R380/R390 Disassembly Flowchart(p.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Revision B From the rear side, push the positioning pin out with a screw driver or similar tool, and slide the FFC Holder upward to remove it from the Middle Housing. FFC Holder Removal Direction When putting the Head FFC through the Ferrite Core, first straighten the fold of the pair of two FFCs, then put the five FFCs through the Ferrite Core one by one taking care not to damage them.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.3.2 Removing the Main Board Unit For R260/R265/R270, when removing the connector cables, also remove the GND Cable of the USB Connector Cable (CN2). This GND Cable is screwed together with the Shield Plate in part . C H E C K P O IN T Parts/Components need to be removed in advance All exterior parts/components / USB Board (R260/R265/R270 only) Removal procedure 1. 2. Disconnect all FFCs and connector cables from the Main board.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Revision B Remove the four screws. (For R260/R265/R270, three screws only) (3 pcs.): C.B.P. M3x10 (tightening torque: 5-7 kgf.cm) (1 pc.): C.P. M3x6 (tightening torque: 7-9 kgf.cm) • Screw • Screw 4. 5. Remove the Main Board, taking extra care not to get the FFC caught on the opening of the CB Support Shield Plate. (R360/R380/R390 only) (The numbers shown in the figure indicate the order of tightening the screws.) Remove the Main Board.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 1. 2. 3. Revision B Install the Main Board Unit following the steps below. Install the MB Frame to the the Lower Housing, and make sure that the Ground Plate MB contacts with the Main Frame. (Screw (1) in Fig.4-54) Install the Main Board Unit screwing it in the order given in Fig.4-54. Install the Main Board Unit to the MB Frame. (Fig.4-59) After installing the Main Board, check that the Ground Plate MB contacts with the Main Frame.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4. Remove the Upper Shield Plate MB from the Main Board following the steps below. For R360/R380/R390 5. Remove the two screws and remove the Lower Shield Plate MB from the Main Board. • Screw : C.P. M3x10 (tightening torque: 5-7 kgf.cm) Lower Shield Plate MB Remove the four screws and remove the Shield Plate MB from the Main Board. • Screw • Screw : C.P.M3x6 (tightening torque: 5-7 kgf.cm) : C.B.S. M3x8 (tightening torque: 5-7 kgf.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.3.4 Removing the Card Board (R360/R380/R390 only) Parts/Components need to be removed in advance All exterior parts/components / Main Board Unit 1. 2. Card Board disassembly Disconnect the FFC from CN1 connector on the Card Board. Remove the screw and remove the Ground Plate CB. • Screw : C.B.S. M3x6 (tightening torque: 5-7 kgf.cm) Card Board Removal C H E C K P O IN T 1. 2. R360/R380/R390 are equipped with a Card Board.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.3.5 Disassembling the Panel Unit 1. 2. Panel Board removal C A U T IO N C H E C K P O IN T Be careful not to scratch or damage the exterior surface (coated or decorative laminated parts) during disassembly and reassembly. Removing the Right/Left Laminated Panels (R360/R380/R390 only) 1. 2. Disengage the four hooks on the rear side of the Panel Unit.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 5. Revision B Remove the screw and remove the Panel Board. 8. • Screw : C.B.P. M3x10 (tightening torque: 5-7 kgf.cm) • Positioning Hole: /Rib: Panel Board Peel off the double-sided tape and remove the two FFCs from the Shield Plate PNL. • Double-sided tape: Shield Plate PNL FFC (1) FFC (2) Figure 4-70. Removing the Panel Board (3) 6. Remove two screws and remove the LCD Panel and the Ground Plate LCD. • Screw : C.B.P.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4. Revision B Remove the SW Button (1)(2)(3) and the LED Light Guide Plate. 1 2 Following instructions are for R360/R380/R390 only When installing the LCD Panel, check that the inner side of the LCD Cover is free of dust or dirt. Install the Shield Plate PNL putting it under the cables connecting the two Panel Boards.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.3.6 Middle Housing 2. Parts/Components need to be removed in advance Remove the Middle Housing taking extra care not to get the FFC caught on the opening part. All exterior parts/components / Card Board (USB Board) / Main Board Unit Removal Direction Removal procedure C H E C K P O IN T Head FFC Refer to the Orientation Definition below for the directions indicated in the following procedures. •“4.1.6 Orientation Definition (p.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.4 Removing the Printer Mechanism C A U T IO N Parts/Components need to be removed in advance All exterior parts/components / All control boards / Middle Housing Do not touch the PF Scale with bare hands or damage it. If the Printer Mechanism is tilted leftward about 15°, the PF Scale hits against the desk surface and can break. After removing the Printer Mechanism, take extra care to protect the PF Scale. 4.4.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 2. Revision B Remove the six screws that secure the Printer Mechanism. : C.B.P. M3x8 (tightening torque: 7-9 kgf.cm) Before installing the Printer Mechanism, make sure that the cables are correctly routed referring to the figure below and the following pages. • Screw (The numbers shown in the figure indicate the order of tightening the screws.) 1 6 [Left side] 2 [Right side] 5 4 3 2 3 1 Figure 4-86. Removing the Screws (Printer Mechanism) 3.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5 Disassembly of the Printer Mechanism 1. 2. 4.5.1 CR Scale 3. C A U T IO N Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. • “4.1.8 Sharp Metal Edges (Danger!)” (p.62) During the disassembly/reassembly of the Printer Mechanism, take extra care not to touch the CR Scale with bare hands, and not to contaminate or scratch it. 4. 5.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5.2 APG Unit C A U T IO N Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. •“4.1.8 Sharp Metal Edges (Danger!) (p.62)” Parts/Components need to be removed in advance Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" Install the APG Unit following the procedure below. 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Revision B 4.5.3 Printhead Install the APG Unit to the Main Frame. C A U T IO N Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. • “4.1.8 Sharp Metal Edges (Danger!)” (p.62) When removing the Head FFC Cover and the Head FFC Cover Inner, do not use tools with sharp ends as the FFC may get damaged.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. Disconnect the FFC from the connector ( Revision B ) on the Head Board. 7. 8. Move the CR Unit to the left (the opposite side to the home position). Taking care not to scratch the cables, insert a flathead screw driver through the hole on the left rear of the Main Frame, and disengage the hook (2) of the CSIC Assy. Hook (2) FFC for CSIC Figure 4-96. Removing the FFC for CSIC 4.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 C A U T IO N Revision B Take extra care not to spill ink and contaminate the surroundings. Be extremely careful not to touch the nozzle surface, the ink supply needles and the Head Cover, otherwise the nozzles may get clogged. 11. Remove the two Head FFCs from the connector on the back, and remove the Printhead. Head Cover Printhead Printhead Head FFC Nozzle surface Figure 4-101. Handling of the Printhead Connector 10.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5.4 Waste Ink Pad 4.5.5 P/S Assy Parts/Components need to be removed in advance Parts/Components need to be removed in advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism Removal procedure C A U T IO N 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 2. Revision B Remove the screw that secures the P/S Assy, and remove the P/S Assy from the Lower Housing. • Screw : C.B.P M3x10 (tightening torque: 5-7 kgf.cm) 4.5.6 Stacker Assy Parts/Components need to be removed in advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism P/S Assy Lower Housing Removal procedure C A U T IO N C H E C K P O IN T 1. 2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 4. Revision B Follow the steps below to remove the CDR Guide Lever Spring. 1) Pull the end A toward you. 2) Pull the end B out of the notch. 3) Pull the end A out of the shaft, and remove the CDR Guide Lever Spring. 7. 8. While disengaging the hook, remove the left gear from the CDR Shaft and remove the Left Stacker Guide. Also remove the Right Stacker Guide in the same way. Remove the CDR Shaft from the Stacker.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B When installing the Stacker Assy, insert the tabs of the Left/ Right Stacker Guides into the hole of the Lower Housing, and secure the guides with the screws. Tighten the screws in the order given in Fig.4-111. 4.5.7 Ink System C A U T IO N Lower Housing Left Stacker Guide Right Stacker Guide Figure 4-114. Reinstalling the Stacker Assy Take extra care to avoid injury from sharp metal edges.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 1. 2. 3. Revision B Move the CR Unit to the center. Remove the screw (1) that secures the Cap section. • Screw : C.B.S. M3x6 (tightening torque: 7-9 kgf.cm) 5. (The numbers shown in the figure indicate the order of tightening the screws.) Insert a screwdriver through the hole of the Main Frame and remove the screw (2) that secure the Pump section. • Screw : C.B.S. M3x6 (tightening torque: 7-9 kgf.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5.8 CR Motor C A U T IO N 2. Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. •“4.1.8 Sharp Metal Edges (Danger!)” (p.62) Remove the Driven Pulley Assy and remove the Timing Belt from the Pinion Gear of the CR Motor.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" When installing the CR Motor, install it so that the print side faces upwards. 4.5.9 EJ Frame Assy C A U T IO N Take extra care to avoid injury from sharp metal edges. Before starting, see the page given below to check the dangerous edges. •“4.1.8 Sharp Metal Edges (Danger!)” (p.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 3. Disengage the connector cables of the PE Sensor and the APG Sensor from the two hooks (A). 4. Remove the two screws and remove the Cable Holder Frame from the two hooks (B). • Screw : C.B.S. M3x6 (tightening torque: 7-9 kgf.cm) 6. Remove the EJ Frame Assy. Removal Direction (The numbers shown in the figure indicate the order of tightening the screws.) EJ Frame Assy Cable Holder Frame Figure 4-130.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B When installing the Front Frame, screw it after securing the foot of the two EJ Frame Springs to the slits as shown in the figure. Carefully handle the EJ Frame as the springs come off easily. 4.5.10 PF Encoder / PF Scale / PF Motor C A U T IO N Left EJ Frame Spring Right EJ Frame Spring Figure 4-133. Reinstalling the Front Frame (2) Screw the Cable Holder Frame in the order given in Fig.4-128.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Removing the PF Motor 4. Peel off the acetate tape (1), and remove the Ferrite Core from the cutout of the ASF Unit. Disengage the PF Motor connector cable from the hook (1) of the ASF Unit. Disengage the cables of the PF Motor and the CR Motor that are secured with two pieces of acetate tape from the two hooks (2), peel off the acetate tape and remove the PF Motor cable.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5.11 ASF Unit 4. Parts/Components need to be removed in advance Remove the Torsion Spring 137.7 from the LD Roller Guide. Torsion Spring All exterior parts/ All control boards / Middle Housing / Printer Mechanism / Ink System Removal procedure C H E C K P O IN T LD Roller Guide Refer to the Orientation Definition below for the directions indicated in the following procedures. “4.1.6 Orientation Definition (p.61)” Figure 4-140.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 7. Revision B Remove the Combination Gear (10, 15.2), and remove the ASF Unit. 4.5.12 CR Unit Parts/Components need to be removed in advance All exterior parts/ All control boards / Middle Housing / Printer Mechanism / CR Scale / APG Unit / CR Motor / EJ Frame Assy Combination Gear Removal Direction [Rear side] ASF Unit Removal procedure Refer to the Orientation Definition below for the directions indicated in the following procedures. •“4.1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 3. 4. Revision B Disengage the end of the Spring (2) from the hook, and the other end from the slit of the CR shaft, and remove the Spring (2). Remove the washer, and remove the Right PG Cam. CR Shaft 6. Remove the CR Shaft from the CR Unit. CR Unit CR Shaft Spring (2) Figure 4-148. Removing the CR Unit (4) Washer 7. Remove the Timing Belt from the CR Unit. CR Unit Removal Direction Right PG Cam Hook Figure 4-146. Removing the CR Unit (2) 5.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" Before attaching the right PG cam, remove the APG Unit and install the cam matching its phase with the APG Unit. (See Fig.4-91, Fig.4- 92) When attaching the spring (2) and the washer for the Right PG Cam to the CR Shaft, make sure to attach them to the positioning slits on the CR Shaft. (See Fig.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5.13 Upper Paper Guide C A U T IO N 2. Be sure to follow the procedure below to remove the Upper Paper Guide to avoid damaging the PE Sensor Lever. It is recommended to place a transparent sheet between the Upper and Front Paper Guides to avoid scratching the roller. Do not touch the roller surface with bare hands as it can adversely affect the print quality. Remove the Upper paper Guide pressing Sensor Lever.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5.14 Front Paper Guide Assy/APG Sensor Assy C A U T IO N Do not touch the surface of the rubber roller of the EJ Roller Assy and the coated part of the PF Roller Assy as it can adversely affect the print quality. 2. Disconnect the connector of the PE Sensor Cable on the rear side of the printer. 3. Remove the screw that secures the Front Paper Guide Assy. • Screw : C.B.S. M3x6 (tightening torque: 7-9 kgf.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 5. Revision B Remove the Front Paper Guide Assy, following the steps below. (1) Lift Lubrication is required. See the page given below for the lubrication information. "6.1.3 Lubrication (p.131)" When installing the Front Paper Guide Assy, pull out the CDR Tray Sensor cable as shown below. part to disengage the left side of the Front Paper Guide Assy. (2) Slide the assy leftward little by little to disengage the right side of the assy.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 4.5.
CHAPTER 5 ADJUSTMENT
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.1 Adjustment Items and Overview This chapter describes adjustments necessary after the disassembly/reassembly of the printer. 5.1.1 Servicing Adjustment Item List The adjustment items of this product are as follows. Table 5-1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 5-1. Adjustment Items Function Item Purpose Method Outline Tool Used Media Use the adjustment program to print out the adjustment pattern, and enter the adjustment value of the printed pattern with no black/white streaks in the block.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 5-2. Maintenance Items Maintenance Items Function Item Purpose Method Outline Used Media • Adjustment Program A4/Letter (Plain paper) Head Cleaning This function is used to execute Cleaning efficiently when ink is not delivered from the Head properly, e.g. dot missing.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.1.2 Replacement Part Adjustment Items The following table indicates the adjustment items for replacement parts. Note: “Required” in this table indicates the adjustment item that must be executed when the corresponding part has been removed/replaced. “-” indicates that no adjustment is required. When you have removed/replaced two or more parts, refer to the corresponding items of all parts.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Table 5-4.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.2 Adjustment by Using Adjustment Program This section explains how to judge print samples by using the adjustment program. Follow the instructions of the adjustment program for details of the adjustment methods. 5.2.1 Top Margin Adjustment 5.2.2 Head angular adjustment Two patterns are printed as shown below. Band pattern Pattern shown below is printed for both 0 to 80 column and 80 to 0 column printing direction.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.2.3 Bi-D Adjustment Microweave Pattern The pattern shown below is printed for each of the 4 print modes. +3 +2 +1 0 -1 -2 -3 1 Figure 5-3. Head angular adjustment Pattern Printing (2) -4 [Judgment method] -2 0 2 Examine the printout +3 to -3 patterns and select the value for the group of which the gaps between the 2 color bars are the smallest. 6 8 3 Figure 5-4.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.2.4 PW Adjustment/First Dot Adjustment PW adjustment Patterns are printed as shown below. [Judgment method] 5 mm -5 -4 -3 -2 -1 0 -8 -7 -6 -5 -4 -3 -2 -1 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 Enter the value of the line located 5mm away from each edge.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.2.5 PF Adjustment PF-Bottom Edge Area PF-Standard Area Patterns are printed as shown below. Patterns are printed as shown below. Upper block -3 -2 -1 0 1 2 3 5 4 3 Lower block 2 Figure 5-7.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 5.2.6 PG Adjustment C A U T IO N Described below is the platen gap (PG) adjustment. Purpose: Adjust the distance between the head surface and the Paper Guide Front Assy (platen) properly and adjust the parallelism on the 0th column side and on the 80th columns side to ensure reliable print quality.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Adjustment procedure C A U T IO N Specified PG value: 1.2 ± 0.1 mm 1. Install new ink cartridges in the carriage. 2. Remove the Cable Holder Frame. (Fig. 4-128) 3. Check that the APG Assy and the carriage are in the PG-position. (Fig. 5-18) 4. The Printhead must come in contact with the 1.3 mm thickness gauges but must not come in contact with the 1.15 mm thickness gauges. Pull the belt to move the carriage Gauge (1.15 or 1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 5.3 Banding Reduction System (BRS) Adjustment/ Paper Feed Amount Profile (PFP) Correction Revision B Specified Scanner to perform the adjustment C A U T IO N 5.3.1 Overview Install the driver of the scanner to the PC in advance. As the profile required for the adjustment is not prepared for scanners other than the ones specified below, BRS/PFP Adjustment can not be carried out by the other scanners.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Adjustment Flow 5.3.2 Adjustment Procedure Carry out the adjustment following the adjustment flow below. 5.3.2.1 BRS (Banding Reduction System) Adjustment START Printing the BRS Adjustment Pattern Printing the BRS Adjustment Pattern Printing the PFP Check Pattern Scanning the BRS Adjustment Pattern Judging the Check Pattern OK cde* Load A4 size Matte Paper-Heavyweight on the paper support. 2.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Scanning the BRS Adjustment Pattern 5.3.2.2 PFP Adjustment 5. Set the printed pattern and the PFP Base Scale on the document table and click the [Scan] button on the “3. Scan Test Pattern” column. Printing the PFP Adjustment Pattern 6. According to the scanned result, BRS calibration values are automatically calculated and are written to the serial flash ROM.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Scanning the PFP Adjustment Pattern Printing the PFP Check Pattern 4. Set the PFP Base Scale and the PFP test pattern on the document table and click the [Scan] button on the “3. Scan Test Pattern” column. 6. 5. According to the scanned result, PFP calibration values are automatically calculated and are written to the serial flash ROM.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B Judging the Check Pattern 7. Referring to Fig. 5-18 check that there is no white or overlapped bands in all the check patterns. If any bands are found, carry out the steps below. 1. Re-print the check pattern to see if the bands appear again. 2. When bands appear in Step 1, try the PFP adjustment again from the beginning. 3.
CHAPTER 6 MAINTENANCE
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 6.1 Overview 6.1.2 Service Maintenance If any abnormal print (dot missing, white line, etc.) has occurred or the printer indicates the “Maintenance request error”, take the following actions to clear the error. (This error is displayed in EPSON Status Monitor 3 and in the LCD Panel for R360/ R380/R390, and with LED for R260/R265/R270.) This section provides information to maintain the printer in its optimum condition. 6.1.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 6.1.3 Lubrication The type and amount of the grease used to lubricate the printer parts are determined based on the results of the internal evaluations. Be sure to apply the specified type and amount of the grease to the specified parts during servicing mentioned below.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B LUBRICATION OF FRONT PAPER GUIDE ASSY Front Paper Guide Assy (left) LUBRICATION OF EJ FRAME ASSY PF Roller Shaft, EJ Roller Shaft and Bushing (3 points) EJ Frame Assy Busing (Left/Right back side) EJ Frame Assy Bushing G-71 ø 1 x 3 mm x 3 points Left Right Apply after installing the Front Paper guide Application Point Apply with Injecto
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Front Frame contact point (right) Revision B Contact position of the Front Frame and the PE Frame Assy (2 points) PG Cam on both ends of CR Shaft Left Right G-71 Rib Apply after installing the CR Shaft Apply before installing the Front Frame Apply with Injector Apply with Injector Apply to the inner edge of the notch for spring.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Contact point between CR Unit and CR Shaft (1) Revision B Contact point between CR Unit and the CR Shaft LUBRICATION OF INK SYSTEM Contact point between Main Frame and I/S G-71 CR Shaft 210 ± 20mg x 2 points G-71 Apply before installing the CR Unit Application Point ø 1 x 1 circle Apply with Injector After lubrication, move the CR Shaft
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Rim of the APG Unit Spur Gear 28.8 Revision B Around the rim of the Spur Gear 28.8 LD Roller Shaft (Curved surface) G-71 USB I/F side Clutch side ø 1 x 1 circle Apply before installing the ASF Unit Apply with Injector Application Point Application Point Figure 6-16.
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 LD Roller Shaft (Curved surface) (Ribs beside the LD Roller) Revision B Contact point between the LD Roller and Hopper, ASF Gear G-71 ø 1 x 1/4-circle x 4 points Apply before assembling the LD Roller Holder Application Point Apply with Injector Rotate the LD Roller Shaft so that the Curved/Flat surface face up, then apply grease to the specified parts. Figure 6-20.
CHAPTER 7 APPENDIX
EPSON Stylus Photo R260/R265/R270, R360/R380/R390 Revision B 7.1 Exploded Diagram / Parts List 7.2 Electrical Circuits This manual does not provide exploded diagrams or parts list. The electric circuit diagrams below are shown at the following pages: For the information, see SPI (Service Parts Information).
Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Sheet : 1/4
Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Rev.
Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Rev.
Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 MAIN Rev.
Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 PNL Rev.
Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 PNL-B Rev.
Model : PM-D870 Stylus Photo R360/R380/R390 Board : C658 STG Rev.
Model : PM-G850 Stylus Photo R260/R265/R270 Board : C653 MAIN Rev.
Model : PM-G850 Stylus Photo R260/R265/R270 Board : C653 PNL Rev.
Model : PM-G850 Stylus Photo R260/R265/R270 Board : C653 I/F Rev.
Model : PM-D870/PM-G850 Stylus Photo R360/R380/R390 Stylus Photo R260/R265/R270 Board : C653 PSB Rev.
Model : PM-D870/PM-G850 Stylus Photo R360/R380/R390 Stylus Photo R260/R265/R270 Board : C653 PSE Rev.
Model : PM-D870/PM-G850 Stylus Photo R360/R380/R390 Stylus Photo R260/R265/R270 Board : C653 HEAD Rev.
