Technical data

Index-2
Index
determining memory requirements,
8-12
storing data to disk, 8-14
types of memory and data storage
,
8-11
using saved calibration sets, 8-16
menu
address
, 5-45
analog in, 5-12
conversion
, 5-12
edit limits
, 5-47
edit segment, 5-48
input ports menu
, 5-13
offset limits
, 5-48
segment, 5-7
S-parameter
, 5-12
stepped edit list
, 5-8
stepped edit subsweep, 5-8
swept edit list
, 5-8
swept edit subsweep
, 5-9
microwave systematic errors,
characterizing
, 5-30
minimum loss pads
, 7-4
minimum sweep time, 5-6
mode
auto sweep time
, 5-5
copy, 5-46
GPIO
, 5-46
manual sweep time
, 5-5
pass control, 5-45
system controller
, 5-45
talker/listener
, 5-45
model
one-port error
, 5-30
two-port error
, 5-35
modifying calibration kits
, 5-43
verifying performance
, 5-43
N
noise reduction techniques
, 5-24
averaging, 5-24
IF bandwidth reduction
, 5-25
smoothing
, 5-24
non-volatile memory, 8-11
O
offset limits menu
, 5-48
one-port error model
, 5-30
operation, GPIB, 5-44
operation, limit line
, 5-47
options available, analyzer
, 7-2
options, service and support
, 7-2
output power
, 5-4
power coupling options
, 5-4
understanding power ranges
, 5-4
P
packaging for shipment
, 10-3
pads, minimum loss, 7-4
pass control mode
, 5-45
performance, verifying
, 5-43
phase format, 5-14
polar format
, 5-16
power coupling options
, 5-4
channel coupling, 5-5
test port coupling
, 5-5
power ranges
, 5-4
automatic mode, 5-4
manual mode
, 5-4
power sweep
, 5-10
power, output, 5-4
preset state
, 8-2
principles, group delay
, 5-19
R
real format
, 5-18
rear panel features and connectors
, 2-8
recommended calibration cycle
, 1-2
reduction, IF bandwidth, 5-25
regulatory information
, 1-2
response and isolation calibration
, 5-42
response calibration, 5-42
S
sales and service offices
, 10-4
saved calibration sets
, 8-16
segment menu, 5-7
segment power, setting
, 5-9
service
, 10-2
sales and service offices, 10-4
service and support options
, 7-2
setting segment IF bandwidth
, 5-9
setting segment power
, 5-9
settings and data
, 2-2
shipping procedure
, 10-2
smith chart format, 5-15
smoothing
, 5-24
source match
, 5-28
S-parameter menu
analog in menu
, 5-12
conversion menu
, 5-12
S-parameters, 5-11
S-parameter menu
, 5-12
understanding
, 5-11
S-parameters menu
input ports menu
, 5-13
specifications
, 1-2
stepped edit list menu
, 5-8
stepped edit subsweep menu
, 5-8
stepped list frequency sweep
, 5-7
segment menu
, 5-7
stepped edit list menu
, 5-8
stepped edit subsweep menu
, 5-8
storing data to disk
, 8-14
sweep time, 5-5
auto sweep time mode
, 5-5
manual sweep time mode
, 5-5
minimum sweep time, 5-6
sweep types
, 5-6
CW time sweep
, 5-10
linear frequency sweep, 5-7
logarithmic frequency sweep
, 5-7
power sweep
, 5-10
stepped list frequency sweep, 5-7
swept list frequency sweep
, 5-8
swept edit list menu
, 5-8
swept edit subsweep menu, 5-9
swept list frequency sweep
, 5-8
setting segment IF bandwidth
, 5-9
setting segment power, 5-9
swept edit list menu
, 5-8
swept edit subsweep menu
, 5-9
SWR format, 5-18
system controller mode
, 5-45
systematic errors
, 5-30
T
talker/listener mode
, 5-45
test port coupling
, 5-5
tracking
, 5-30
two-port error model, 5-35
U
understanding power ranges
, 5-4
understanding S-parameters
, 5-11
using the parallel port, 5-46
copy mode
, 5-46
GPIO mode
, 5-46
V
verifying performance
, 5-43
volatile memory
, 8-11