Product Information Guide

ManualsBrandsEpson ManualsProjectorsEpson PowerLite S3 Multimedia Projector

Epson PowerLite S3 Projector

3/05 Epson PowerLite S3 Projector - 1

Projector Parts Projector Specifications

General

Type of display Poly-silicon Thin Film Transistor (TFT)

active matrix with Micro Lens Array

Size of liquid

crystal panels Diagonal: 0.5 inch (12.5 mm) × 3

Lens F=1.4 mm, f=16.6 mm

Focus adjustment Manual

Zoom ratio Digital zoom 1.0 to 1.35, lens at

maximum size

Resolution 800 × 600 pixels (native format)

SXGA (1280 × 1024) max (resized)

Number of pixels 480,000 × 3

Brightness 1600 (high brightness) ANSI lumens

1400 (low brightness) ANSI lumens

Contrast ratio 500:1

EPSON Control

Code ESC/VP 21 (available online)

Image size

(diagonal) 30 to 300 inches (0.9 to 12.1 m)

Projection distance 2.9 to 29.5 ft (0.9 to 9.0 m), Wide mode

3.9 to 39.7 ft (1.2 to 12.1 m), Tele mode

Projection methods Front, rear, upside-down (ceiling

mount)

Sound output 1W monaural

Optical aspect ratio 4:3 (horizontal : vertical)

Keystone correction

angle

±30° vertical

±20° vertical at 16:9 aspect ratio

Keystone correction

ratio 9.6:1 offset

Supported video

interface standards NTSC, NTSC4.43, PAL, PAL-M,

PAL-N, PAL60, SECAM

Projection Lamp

Type UHE (Ultra High Efficiency)

Power consumption 135W

Lamp life About 2000 hours (high brightness)

About 3000 hours (low brightness)

Part number V13H010L33

Lens

cover

Focus ring

Infrared

receiver for

remote control

Control panel

Foot

lever

Ventilation outlets

Lamp cover

Computer/Component Video port

S-Video port

Video port

Audio

input

Monitor out port

inlet

Speaker

Infrared receiver for

remote control

USB port

(not for projecting)

Rear

adjustable

foot

Air filter

(air intake vent)

Ceiling mount holes

Foot

Foot lever

Summary of content (14 pages)

PAGE 1
Epson PowerLite S3 Projector Projector Parts Projector Specifications Focus ring Control panel General Infrared receiver for remote control Lamp cover Type of display Foot lever Size of liquid crystal panels Diagonal: 0.5 inch (12.5 mm) × 3 Lens F=1.4 mm, f=16.6 mm Focus adjustment Manual Zoom ratio Digital zoom 1.0 to 1.
PAGE 2
Epson PowerLite S3 Projector Remote Control Range Battery Computer 20 feet (6 meters) 2 AAA Dimensions Height 3.4 inches (86 mm) 3.9 inches (98 mm) with foot extended Width 12.9 inches (327 mm) Depth 9.7 inches (246 mm) Weight approximately 5.5 lb (2.
PAGE 3
Epson PowerLite S3 Projector Image Size and Projection Distance Positioning the Projector The distance between the projector and the screen determines the basic size of the projected image, as shown below. Because other adjustments—such as those made with the Aspect and Keystone buttons—also affect the size of the image, the numbers shown in the illustration should be considered for general guidelines, not exact measurements.
PAGE 4
Epson PowerLite S3 Projector 5. Press the P Power button on the remote control or the top of the projector to turn on the projector. Turning the Projector On and Off Power button Once you’ve connected the projector to your computer or other equipment, follow these instructions to turn it on and display an image: 1. Make sure the power is turned off for the projector and any sources connected to it. 2. Remove the lens cover.
PAGE 5
Epson PowerLite S3 Projector If you’re using a Macintosh® notebook with Mac OS® X: 3. Press the P Power button again. The lamp is turned off and the P Power light flashes orange as the projector cools down. When the projector has cooled, the P Power light stays orange and the exhaust fan shuts off. 1. Select System Preferences from the Apple® menu and click Displays. Note: If you want to turn the projector on again, wait until the orange light stops flashing. Then press the P Power button. 2.
PAGE 6
Epson PowerLite S3 Projector If you’re using a Macintosh notebook with Mac OS 9.x or earlier: Adjusting the Image 1. From the Apple menu, select Control Panels, then click Monitors and Sound. The following sections describe how to adjust the image once it is displayed. 2. Click the Arrange icon, and then drag one monitor icon on top of the other. Adjusting the Height of the Image Click here The projector should be as perpendicular to the screen as possible.
PAGE 7
Epson PowerLite S3 Projector Adjusting the Image Size Adjusting the Image Shape You can adjust your image size using the zoom buttons on the projector, or zoom into a portion of the image using the E-Zoom buttons on the remote control. When the projector is raised in the front or back, the display distorts in the shape of a trapezoid. Note: You can correct only vertical distortion with this function. Using the Zoom Buttons Press the u or d buttons to correct the distortion.
PAGE 8
Epson PowerLite S3 Projector Sometimes the signals may not be adjusted correctly, depending on the type of signals being output by the computer. In such cases, use the Image menu to adjust the tracking and sync settings manually. Selecting the Color Mode There are seven color modes. The mode changes each time you press the Color Mode button on the remote control. Make a selection appropriate for the image and current conditions.
PAGE 9
Epson PowerLite S3 Projector Like the A/V Mute feature, if you are projecting a video, the video and audio continue while the projected image is paused, so when you press the Freeze button again to resume, the playback does not resume where you stopped it. Light Status Description and action Power red The projector has an internal temperature error (overheating). The lamp turns off automatically and projection stops.
PAGE 10
Epson PowerLite S3 Projector ❏ A strong light source (such as direct sunlight) shines into the infrared receiver Using the Menus ❏ Other equipment emitting infrared energy is present (such as a radiant room heater) The on-screen menus let you adjust and customize the projector features from the remote control: ❏ Image controls the look and quality of the projected image (from a computer or video source).
PAGE 11
Epson PowerLite S3 Projector Replacing Remote Control Batteries Cleaning the Projector Case When the batteries run out, follow the steps below to replace them. The remote requires 2 AAA batteries. Before you clean the projector case, turn off the projector and unplug the power cord. Note: Make sure you read the Safety Instructions in the User’s Guide before handling the batteries. ❏ To remove dirt or dust, wipe the outside with a soft, dry, lint-free cloth. 1.
PAGE 12
Epson PowerLite S3 Projector Replacing the Air Filter Replacing the Lamp If you need to replace the air filter, you can obtain it from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit www.epsonstore.com (U.S. sales only). In Canada, please call 800-463-7766 for reseller referral. It is time to replace the lamp when: ❏ The message “Replace the Lamp.
PAGE 13
Epson PowerLite S3 Projector 3. Loosen the lamp cover screw with the screwdriver that is supplied with the spare lamp (or your own cross head [Phillips] screwdriver). 7. Insert the new lamp so that it fits in place correctly. Once it is fully inserted, tighten the two screws. 4. Then slide the lamp cover straight forward and lift it to remove. 5. Loosen the two lamp screws with the screwdriver that is supplied with the spare lamp (or your own cross head [Phillips] screwdriver). 8.
PAGE 14
Epson PowerLite S3 Projector 2. Select Reset from the configuration menu, and then select Lamp-Hours Reset. Optional Accessories You can purchase screens, carrying cases, or other accessories from an Epson authorized reseller. For product information and to find the nearest authorized reseller, please call 800-GOEPSON (800-463-7766) or browse our catalog of products at www.epson.com, select the product you are interested in, and click “Where to Buy.” To purchase online, please visit the Epson Store at www.