PowerLite Pro G5450WUNL/G5550NL/ G5650WNL/G5750WUNL/ G5950NL Multimedia Projector ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. This information is subject to change without notice. © 2010 Epson America, Inc.
C Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 13 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 13 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1 Setting Up the Projector . . . . . . . . . . . . . . . . . . . . .
Connecting to a Digital Camera or Other USB Device . . . . 50 Removing the USB Device or Cable . . . . . . . . . . . . . . . 51 Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . . 51 Using the Direct Power On Function . . . . . . . . . . . . . . 53 Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . 54 6 2 Displaying and Adjusting the Image . . . . . . . . 55 Displaying an Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Adjusting the Image . .
Using Quick Wireless Connection . . . . . . . . . . . . . . . . . . . . 79 Configuring Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Configuring a Wireless Connection . . . . . . . . . . . . . . . . . . . 81 Configuring the Projector . . . . . . . . . . . . . . . . . . . . . . . 82 Selecting Wireless Network Settings in Windows. . . . . . 84 Selecting Wireless Network Settings in Mac OS. . . . . . . 85 Making a WPS (Wi-Fi Protected Setup) Connection . . .
Projector Menu and Options List . . . . . . . . . . . . . . . . . . . . 129 8 6 Maintaining the Projector. . . . . . . . . . . . . . . . . . 133 7 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 A Projector Installation . . . . . . . . . . . . . . . . . . . . . . . 163 Cleaning the Lens. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . 134 Cleaning the Air Filter . . . . . . . . .
B Technical Specifications . . . . . . . . . . . . . . . . . . . . 169 C Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 179 FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 183 Software Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W - Welcome The PowerLite ® Pro G5450WUNL/G5550NL/G5650WNL/ G5750WUNL/G5950NL is an easy-to-use, lightweight projector. It offers up to 4000 lumens (G5450WUNL), 4500 lumens (G5550NL/G5650WNL/G5750WUNL), or 5200 lumens (G5950NL) of brightness, and provides a native XGA (G5550NL/G5950NL), WXGA (G5650WNL), or WUXGA (G5450WUNL/G5750WUNL) resolution. You can connect it to a wide range of computers and video sources. You can project from a USB storage device, or over a wired network.
Additional enhancements: ■ Crestron RoomView® compatibility ■ A Message Broadcasting plug-in that allows you to project timely alerts and messages to all networked projectors (to download both the plug-in and its instructions, visit Epson’s support website at www.epson.com/support (U.S.) or www.epson.ca/support (Canada) and select your product).
Using Your Documentation Please follow these guidelines as you read through this manual: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector. ■ Tips contain additional projection hints. note In some cases, the illustrations in this guide may not exactly match your projector.
■ PC Free Operation Guide Provides instructions on projecting files from a USB storage device or digital camera that is connected to the projector (installed along with this manual from the projector CD). ■ EasyMP Slide Converter Operation Guide Provides instructions on using the EasyMP Slide Converter software to convert and transfer presentations to a USB storage device so that you can present without using a computer (installed along with this manual from the projector CD).
Optional Accessories To enhance your use of the projector, Epson offers the following optional accessories: Product Part number Replacement lamp for PowerLite Pro G5450WUNL/G5550NL V13H010L62 Replacement lamp for PowerLite Pro G5650WNL/G5750WUNL/G5950NL V13H010L63 Replacement air filter V13H134A17 Standard Zoom Lens <1.64 - 2.5> Middle Throw Zoom Lens 1 <1.83 - 2.45> Middle Throw Zoom Lens 2 <1.83 - 2.53> Long Throw Zoom Lens <1.84 - 2.32> Rear Projection Wide Lens <2.
You can purchase screens or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
1 1 Setting Up the Projector T his chapter tells you how to unpack the projector and connect it to a notebook or desktop computer, to video equipment, such as a Blu-ray Disc™/DVD player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera, and/or to your local area network. You can also connect the projector to a USB storage device or digital camera.
Unpacking the Projector After unpacking the projector, make sure you have all these parts: PDF manuals and registration CD-ROM Projector software CD-ROM Projector and lens cap Cable cover Power cord Remote control and 2 AA batteries VGA computer cable Password Protected sticker Interface label stickers note If you mount the projector on the ceiling, the interface and button names on the projector will appear upside down.
■ To receive a component video signal from your video device, you’ll need a component video cable. One may be provided with your video equipment. ■ To receive an RGB or component video signal from a video device that has RGB or component (PrPbY or CrCbY) connectors, you’ll need a BNC-type video cable. One may be provided with your video equipment. ■ To receive an S-Video signal, you’ll need an S-Video cable. One may be provided with your video equipment.
PowerLite Pro G5450WUNL/G5750WUNL, 16:10 image, Standard zoom lens (part number V12H004S05) Projection distance (A) Wide to Tele Offset (B) 50 inches 53 to 97 inches (136 to 246 cm) -2.2 to 28.7 inches (-6 to 73 cm) 60 inches 64 to 117 inches (164 to 296 cm) -2.7 to 34.5 inches (-7 to 88 cm) 80 inches 87 to 156 inches (220 to 397 cm) -3.5 to 45.9 inches (-9 to 117 cm) 100 inches 109 to 196 inches (276 to 497 cm) -4.4 to 57.
Projection distance (A) Wide to Tele Offset (B) 150 inches 294 to 446 inches (746 to 1132 cm) -6.6 to 86.1 inches (-17 to 219 cm) 200 inches 393 to 595 inches (998 to 1512 cm) -8.9 to 114.9 inches (-22 to 292 cm) 250 inches 492 to 745 inches (1250 to 1893 cm) -11.1 to 143.6 inches (-28 to 365 cm) 300 inches 591 to 895 inches (1502 to 2273 cm) -13.3 to 172.
PowerLite Pro G5450WUNL/G5750WUNL, 16:10 image, Long throw zoom lens (part number V12H004L06) Projection distance (A) Wide to Tele Offset (B) 50 inches 215 to 292 inches (546 to 742 cm) -2.2 to 28.7 inches (-6 to 73 cm) 60 inches 259 to 352 inches (659 to 894 cm) -2.7 to 34.5 inches (-7 to 88 cm) 80 inches 348 to 472 inches (885 to 1199 cm) -3.5 to 45.9 inches (-9 to 117 cm) 100 inches 437 to 592 inches (1111 to 1503 cm) -4.4 to 57.
PowerLite Pro G5650WNL, 16:10 image, Standard zoom lens (part number V12H004S05) Projection distance (A) Wide to Tele Offset (B) 30 inches 32 to 59 inches (81 to 149 cm) -1.5 to 17.4 inches (-4 to 44 cm) 40 inches 43 to 79 inches (109 to 200 cm) -2 to 23.2 inches (-5 to 59 cm) 50 inches 54 to 99 inches (138 to 251 cm) -2.5 to 29 inches (-6 to 74 cm) 60 inches 66 to 119 inches (167 to 302 cm) -3 to 34.8 inches (-8 to 88 cm) 80 inches 88 to 159 inches (224 to 405 cm) -4 to 46.
PowerLite Pro G5650WNL, 16:10 image, Middle throw zoom lens 1 (part number V12H004M04) Projection distance (A) Wide to Tele Offset (B) 40 inches 77 to 118 inches (196 to 301 cm) -2 to 23.2 inches (-5 to 59 cm) 50 inches 97 to 149 inches (247 to 378 cm) -2.5 to 29.0 inches (-6 to 74 cm) 60 inches 117 to 179 inches (298 to 456 cm) -3 to 34.8 inches (-8 to 88 cm) 80 inches 158 to 241 inches (401 to 611 cm) -4 to 46.
Projection distance (A) Wide to Tele Offset (B) 100 inches 297 to 453 inches (754 to 1150 cm) -5 to 58 inches (-13 to 147 cm) 150 inches 448 to 682 inches (1139 to 1733 cm) -7.6 to 87.1 inches (-19 to 221 cm) 200 inches 600 to 912 inches (1524 to 2316 cm) -10.1 to 116.1 inches (-26 to 295 cm) 250 inches 751 to 1141 inches (1909 to 2899 cm) -12.6 to 145.1 inches (-32 to 369 cm) 300 inches 903 to 1371 inches (2294 to 3482 cm) -15.1 to 174.
PowerLite Pro G5650WNL, 16:10 image, Rear projection wide lens (part number V12H004R03) Screen size Projection distance (A) Wide to Tele Offset (B) 30 inches 19 inches (47 cm) 7.9 inches (20 cm) 40 inches 25 inches (64 cm) 10.6 inches (27 cm) 50 inches 32 inches (81 cm) 13.2 inches (34 cm) 60 inches 39 inches (98 cm) 15.9 inches (40 cm) 80 inches 52 inches (132 cm) 21.2 inches (54 cm) 100 inches 65 inches (166 cm) 26.5 inches (67 cm) 150 inches 99 inches (251 cm) 39.
Projection distance (A) Wide to Tele Offset (B) 150 inches 159 to 285 inches (403 to 725 cm) 0 to 90 inches (0 to 229 cm) 200 inches 212 to 381 inches (539 to 968 cm) 0 to 120 inches (0 to 305 cm) 250 inches 266 to 477 inches (675 to 1211 cm) 0 to 150 inches (0 to 381 cm) 300 inches 319 to 572 inches (811 to 1454 cm) 0 to 180 inches (0 to 457 cm) Screen size PowerLite Pro G5550NL/G5950NL, 4:3 image, Middle throw zoom lens 1 (part number V12H004M04) Projection distance (A) Wide to Tele Offset
PowerLite Pro G5550NL/G5950NL, 4:3 image, Middle throw zoom lens 2 (part number V12H004M05) Projection distance (A) Wide to Tele Offset (B) 40 inches 109 to 168 inches (276 to 427 cm) 0 to 24 inches (0 to 61 cm) 50 inches 138 to 212 inches (350 to 538 cm) 0 to 30 inches (0 to 76 cm) 60 inches 166 to 256 inches (423 to 649 cm) 0 to 36 inches (0 to 91 cm) 80 inches 224 to 343 inches (569 to 871 cm) 0 to 48 inches (0 to 122 cm) 100 inches 282 to 430 inches (716 to 1093 cm) 0 to 60 inches (0 to
Projection distance (A) Wide to Tele Offset (B) 100 inches 424 to 574 inches (1076 to 1457 cm) 0 to 60 inches (0 to 152 cm) 150 inches 639 to 864 inches (1623 to 2194 cm) 0 to 90 inches (0 to 229 cm) 200 inches 854 to 1154 inches (2170 to 2932 cm) 0 to 120 inches (0 to 305 cm) 250 inches 1070 to 1445 inches (2717 to 3669cm) 0 to 150 inches (0 to 381 cm) 300 inches 1285 to 1735 inches (3264 to 4407 cm) 0 to 180 inches (0 to 457 cm) Screen size PowerLite Pro G5550NL/G5950NL, 4:3 image, Rear
note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector. You can purchase this from Epson; see page 15. Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be about level with the bottom of the screen.
Connecting to the DVI-D Port (G5450WUNL/G5750WUNL only) 1. Locate a DVI-D cable. 2. Connect the cable to the DVI-D connector on your computer and the DVI-D connector on the projector. 3. If you want to play sound through the projector, see page 46 for instructions on connecting audio cables. With the optional wireless mouse receiver (see page 70), you can use the remote control as a mouse. 4.
Connecting a DVI-D Source to the HDMI Port You can connect your DVI-D source to the projector using a DVI/HDMI conversion cable. 1. Locate a DVI/HDMI conversion cable. 2. Connect the cable to the DVI-D connector on your computer and the HDMI connector on the projector. note With the PowerLite Pro G5450WUNL/ G5750WUNL, you must connect your DVI-D source to the DVI-D port in order to play sound. 32 Setting Up the Projector 3.
Connecting to the HDMI Port 1. Locate an HDMI cable. 2. Connect the cable to the HDMI connector on your computer and the HDMI connector on the projector. 3. See page 51 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image. With the optional wireless mouse receiver (see page 70), you can use the remote control as a mouse.
Connecting to the Computer Port You can connect to the projector using the VGA computer cable that came with it (the monitor port on your computer must be a mini D-sub 15-pin port). 1. If you’re using the VGA computer cable, connect one end to the projector’s Computer1 port, and the other end to your computer’s monitor port. With the PowerLite Pro G5550NL/G5650WNL/G5950NL, you can also connect to the Computer2 port.
Connecting to the BNC Connectors 1. Obtain a commercially available standard BNC to VGA video cable. 2. Plug the BNC connectors into the projector’s B/Cb/Pb, G/Y, and R/Cr/Pr connectors as shown below. Depending on your computer’s video card, you may have to connect to the projector’s V Sync and H/C Sync connectors too. (See your computer documentation for more information.) 3. Plug the VGA connector on the other end of the cable into your computer’s monitor port. 4.
Connecting to Video Equipment You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections: ■ If your video player has an HDMI connector, see “Connecting an HDMI Video Source” on page 37.
■ If your video player has an RGB video port (either a single connector for a VGA monitor cable or three connectors labeled R/G/B), see “Connecting an RGB Video Source” on page 43. VGA connector (RGB video) After connecting video cables, you may also want to connect an audio cable to play sound through the projector; see page 46. If you connect using an HDMI cable, the video and sound are both transferred and you won’t need to connect any additional cables for audio.
Connecting a DVI-D Video Source to the DVI-D Port (G5450WUNL/G5750WUNL only) 1. Locate a DVI-D cable. 2. Connect the cable to the DVI-D connector on your player and the DVI-D connector on the projector. 3. If you want to play sound through the projector, see page 46 for instructions on connecting audio cables. 4. When you’ve finished making any connections, see page 51 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.
Connecting a DVI-D Video Source to the HDMI Port You can connect your DVI-D source to the projector using a DVI/HDMI conversion cable. 1. Locate a DVI/HDMI conversion cable. 2. Connect the cable to the DVI-D connector on your player and the HDMI connector on the projector. 3. With the PowerLite Pro G5550NL/G5650WNL/G5950NL, if you want to play sound through the projector, see page 46 for instructions on connecting audio cables. 4.
Connecting a Composite Video Source note If the video cable was not provided with your video device, you can purchase one from an electronics dealer. 1. If your video cable has an RCA connector, connect it to the yellow video output connector on your player and the yellow Video2 connector on the projector (as shown below). Or if you’re using a coax video cable, connect it to the Video1 connector on the projector. 2.
Connecting an S-Video Source 1. Connect the S-Video cable to the S-Video connector on your player and the S-Video connector on the projector. 2. If you want to play sound through the projector, see page 46 for instructions on connecting audio cables. 3. When you’ve finished making any connections, see page 51 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.
Connecting a Component Video Source note If the component video cable was not provided with your video device, you can purchase one from an electronics dealer. 1. Look at the connectors at one end of your component video cable. If they are bayonet (BNC) connectors, go on to step 2. If they are RCA connectors, you’ll need to attach commercially available BNC adapters to plug the cable into your projector, then continue with step 2. 2.
Connecting an RGB Video Source Connecting Using a VGA Computer Cable 1. Locate the VGA computer cable provided with the projector. 2. Connect the cable to the video port on your player and the Computer1 port on the projector. With the PowerLite Pro G5550NL/G5650WNL/G5950NL, you can also connect to the Computer2 port. note Be sure your video player is not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation. 3.
Connecting Using a BNC Cable 1. Locate a BNC video cable (one may be included with your video equipment). 2. Connect the cable between your player and the corresponding R/G/B connectors on the projector. 3. You may need to change the Input Signal setting in the projector’s Signal menu to RGB (see page 118). 4. If you want to play sound through the projector, see page 46 for instructions on connecting audio cables. 5.
Connecting an External Monitor If you want to monitor your computer presentation close-up (on a monitor placed beside the projector) as well as on the screen, you can connect an external monitor. You can use it to check on your presentation even if you’ve pressed the A/V Mute button or switched to a different picture source. First make sure your computer’s VGA cable is connected to the projector’s Computer1, Computer2 (G5550NL/G5650WNL/ G5950NL only), or BNC ports (see page 34).
Playing Sound Through the Projector note If you have equipment connected to the LAN port, in most cases you do not need to connect an additional cable for sound. You can, however, connect an audio cable to the Audio1, Audio2, or Audio3 port (as described in this section) and output the sound by adjusting the Audio Input setting. With the PowerLite G5550NL/ G5650WNL/G5950NL, you can also adjust this setting for equipment connected to the HDMI port. See page 119.
■ If you have equipment connected to the DVI-D port (G5450WUNL/G5750WUNL only), use a stereo mini-jack cable. Connect the cable to the Audio2 port. ■ If you have equipment connected to the BNC ports, use a stereo mini-jack cable. Connect the cable to the Audio3 port.
■ If you have equipment connected to the Video1, Video2, or S-Video ports, connect an RCA audio cable to the Audio4 ports. 2. Connect the other end of the cable to the audio output connector(s) on your computer or video equipment.
Connecting External Speakers You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projector’s built-in speaker system is disabled. You can use the remote control or the projector’s menu system to adjust the volume. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end.
Connecting to a Digital Camera or Other USB Device note Use a cable less than 10 feet (3 meters) long and connect the camera or other device directly to the projector. Your projector may not function correctly if you use a longer cable or connect your camera to a USB hub. If you connect a USB hard drive, make sure you use the AC adapter to power the hard drive.
Removing the USB Device or Cable If you’re using PC Free mode to project your images, videos, or presentations, stop the projection before you remove the USB device or cable from the projector. 1. If you’re projecting a still image, press the Esc button on the remote or the projector’s control panel. 2. If you’re projecting a slideshow of your images, a movie, or a presentation, press the Esc button on the remote or the projector’s control panel.
2. Plug one end of the power cord into the projector, and the other end into an electrical outlet. The Ppower light turns orange. Power light 3. Press the Ppower button on the remote control or on the back of the projector.
The projector beeps once and the Ppower light flashes green as the projector warms up, then an image begins to appear. When the Ppower light stops flashing and remains green, the projector is ready for use. 4. If you are prompted to enter a password, see page 122. warning Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children and pets. Using the Direct Power On Function The Direct Power On function enables faster setup.
Shutting Down the Projector note Turn off this product when not in use to prolong the life of the projector. This projector incorporates Instant Off technology. To turn it off, you can press its Ppower button as described below, unplug it, or turn off a power switch that supplies power to the projector. You don’t have to wait for the projector to cool down first. 1. To turn off the projector, press the Ppower button on the remote control or projector. You see a confirmation message.
2 2 Displaying and Adjusting the Image Follow the guidelines in this chapter for: ■ Displaying an image ■ Adjusting the image ■ Projecting two images simultaneously 55
Displaying an Image You may need to select the image source if you have multiple video sources connected to the projector (such as a computer or DVD player). Selecting the image source lets you switch between images input from different pieces of connected equipment. If you don’t see the image you want, press the Search button or one of the Source buttons on the remote control, or the Source Search button on the projector until you see the image you want to project.
Adjusting the Position of the Image You can use the vertical lens shift dial on the top of the projector to move your image up or down, or you can use the horizontal lens shift dial to move your image left or right. Vertical Horizontal Additionally, if the projector is on a table, you can use the projector’s adjustable feet to adjust the image: 1. Stand behind the projector. Press the foot release lever up and lift the front of the projector.
3. If necessary, you can fine-tune the height or level the image by turning any of the projector’s adjustable feet. Focusing and Zooming the Image Turn the focus ring on the projector to sharpen the image. Turn the zoom ring (using the knobs on the ring) to reduce or enlarge the image. note If you have installed the Rear Projection Wide Lens (part number V12H004R03), you cannot use the zoom ring to reduce or enlarge the image, but you can still use the E-Zoom buttons on the remote control.
You see this screen: 5. Use the pointer button on the remote control (or the arrow buttons on the projector) to select the corner you want to adjust, and press Enter. 6. Use the pointer button on the remote control (or the arrow buttons on the projector) to adjust the shape, then press Esc when you are finished. note To undo your Quick Corner adjustments, press and hold the Esc button for about 2 seconds, select Reset Quick Corner from the screen that appears, then press Enter. 7.
5. Select H-Keystone (for horizontal adjustment) or V-Keystone (for vertical adjustment) and use the pointer button on the remote control to adjust the shape of the image. Vertical keystone adjustment Horizontal keystone adjustment If the image becomes smaller, use the zoom ring to enlarge the image so it fits the screen. If the image contains faint lines or a gridlike pattern, decrease the sharpness setting (see page 115). 6. When you’re done, press Menu to exit.
■ sRGB: Matches the color palette of standard sRGB computer displays. ■ DICOM SIM: Ideal for projecting X-ray photographs and other medical images. ■ Customized: For manual color adjustment (see page 115). note The projector is not a medical device and cannot be used for medical diagnosis. You can also change the Color Mode using the projector’s Image menu. See page 114 for details.
(G5650WNL), or 1920 × 1200 (G5450WUNL/G5750WUNL); images are cut off if the resolution is over 1024 × 768 (G5550NL/G5950NL), 1280 × 800 (G5650WNL), or 1920 × 1200 (G5450WUNL/G5750WUNL). Press the Aspect button repeatedly to cycle through the available options. You can also change the aspect ratio using the projector’s Signal menu. See page 116 for details. note In order to use the Split Screen feature, one of your images must be input through the HDMI or DVI-D (G5450WUNL/ G5750WUNL only) port.
Depending on the video signals that are input, the images on the left and right may not appear at the same size even if you choose Equal as the sizing option. 6. To end the split screen, do one of the following: ■ Press the Esc button on the remote control or the projector’s control panel. ■ Press the Split button on the remote control. ■ Select Exit Split Screen from the Split Screen Setup window and press Enter.
■ The image on the left side of the screen can be output to an external monitor as long as it meets the requirements (see page 45). You can also activate the split screen using the projector’s Signal menu. See page 119 for details.
3 3 Presenting With the Remote Control The projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 49 feet (15 meters) away. You can use the remote control to adjust the picture and sound (page 66), as a pointer to highlight your presentation (page 69), or to control two or more projectors at the same time (page 71).
note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve battery power. When you release the button, normal operation resumes. Using the Remote Control Make sure batteries are installed as described on page 142. Follow these tips for using the remote control: ■ Point the remote control at the front of the projector or at the screen. ■ Stand within 49 feet (15 meters) of the projector.
Turning Off the Picture and Sound You can temporarily turn off the image and sound by pressing the A/V Mute button on the remote control. This turns the image black and stops the sound. To turn the image and sound back on, press the button again. You can have the screen turn blue (using the Display setting as described on page 126) or display an image such as a company logo when you press the A/V Mute button. (See page 123 for more information on displaying an image.
Zooming Part of Your Image You can zoom in on a portion of the image using the E-Zoom buttons on the remote control. 1. Press the E-Zoom button on the remote control. You see a crosshair indicating the center of the zoom-in area. 2. Use the pointer button to position the crosshair. button to enlarge the selected 3. Continue pressing the E-Zoom area up to 4 times. 4.
Highlighting Your Presentation You can display a pointer to call out important information on the screen, and you can choose from three shapes for the pointer. Using the Pointer Tool 1. To activate the pointer tool, press the Pointer button on the remote control. A pointer appears on the screen. Pointer If you prefer to use a different style of pointer, see the instructions in the next section. 2. Use the pointer button on the remote control to position the pointer on the screen. 3.
Operating Your Computer With the Remote Control With the optional wireless mouse receiver (see page 15), you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering slideshow-style presentations, since you won’t have to stand next to the computer to change slides. note You can also use the Up and Down buttons to move through a presentation that is being projected over a network or from a device connected to the projector’s USB port.
Operating Two or More Projectors With the Remote Control If you’re using more than one projector, you can control all the projectors—or just selected ones—by using the projector ID system. To operate a projector, set the remote control’s ID to match that of the projector. Or you can control all the projectors at once by setting the remote control’s ID to zero. Setting the Projector ID The projector’s default ID is set to Off. This lets it respond to commands from any remote control.
Checking the Projector ID You can check the projector’s ID by following these steps: 1. Move the remote control ID switch to the On position. 2. Point the remote control at the projector you want to check. 3. While holding the ID button, press the Help button. You see a message on the screen like this: Setting the Remote Control ID The remote control’s default ID is zero. This lets you operate any projector. To set it to operate a specific projector, follow these steps: 1.
2. Press and hold the ID button on the remote control. 3. While holding the ID button, press a numbered button on the remote control (0 through 9) to select the desired ID. Select zero to control all projectors, or select a number to match the ID of the projector(s) you want to operate.
Presenting With the Remote Control
4 4l Using the Projector on a Network You can use Quick Wireless Connection or EasyMP ® Network Projection to project images shown on your computer screen— including text, graphics, and video—directly to your audience. See the EasyMP Network Projection Operation Guide for information on features and use. You can use EasyMP Monitor (available for Windows only) to monitor and control your projector through the network.
For a wireless connection, make sure you’ve installed the optional Wireless 802.11g/b/a Module, as described on page 78. Then follow the steps in this chapter to use Quick Wireless Connection (Windows only) or configure your projector and network. See the EasyMP Network Projection Operation Guide for instructions on installing the EasyMP Network Projection software. The EasyMP Network Projection Operation Guide also contains instructions on using the software to project over the network.
6. Choose Wired LAN and press Enter. You see the following screen: 7. Do one of the following: ■ If your network assigns addresses automatically, turn on the DHCP setting. ■ If your network does not assign addresses automatically, turn off DHCP and enter the projector’s IP Address, Subnet Mask, and Gateway Address. To enter numbers, use the pointer button on the remote control to highlight the number you want to input, then press the Enter button. 8.
Installing the Optional Wireless 802.11g/b/a Module Make sure you have the optional Wireless 802.11g/b/a Module. Turn off the projector and disconnect the power cord before you install the module. 1. Remove the cover from the wireless module’s insertion area. 2. Insert the Wireless 802.11g/b/a Module as shown. 3. Fasten the module using the screw that came with it.
If you have the optional USB key, you can use Quick Wireless connection as described in the next section. Or, you can configure your connection manually as described on page 80. Using Quick Wireless Connection Using the optional USB key, you can quickly connect the projector to a Windows computer wirelessly without any configuration. First, make sure you have installed the optional wireless module as described on page 78 and turned on the projector. 1. Connect the USB key to the projector’s USB port.
Configuring Basic Settings You can give your projector a unique name, enable a projector keyword, or create a password for controlling the projector over the Web. 1. Press the Menu button, then choose Network and press Enter. 2. Choose Network Configuration and press Enter. You see a screen like the following: 3. Make sure the projector has a unique name, so you can identify it on your network. If you need to rename it, highlight the Projector Name text box then press Enter. 4.
5. If you want to create a password for using PJLink to control the projector, highlight PJLink Password, press Enter, and enter a password of up to 8 alphanumeric characters. When you’re done, highlight Finish and press Enter. 6. If you want to create a password for remote access to the projector, highlight Web Control Password, press Enter, and enter a password of up to 8 alphanumeric characters. When you’re done, highlight Finish and press Enter. 7.
■ Access Point mode (infrastructure mode) lets multiple computers access the projector at the same time and easily trade off control over the projector. To use Access Point mode, you need a wireless (802.11g, 802.11b, or 802.11a) access point or an AirPort Extreme (or AirPort) base station, and one or more computers with wireless network cards or adapters. Configuring the Projector 1. Press the Menu button, then choose Network and press Enter. 2. Choose Network Configuration and press Enter. 3.
6. If your network is using 802.11b/g, use the pointer button on the remote control to select a Channel setting. If interference occurs, select a different channel. 7. If your network is using 802.11a, use the pointer button on the remote control to highlight 802.11a, then press Enter to select it. 8. If you are connecting in Quick mode, you can set SSID Auto Setting to On to find the projector faster and create a more stable connection. Skip step 9 if you activate this setting.
■ To enter numbers, use the arrow buttons on the remote control to select each number on the screen, then press the Enter button. When you’re finished entering an address in the network menu, highlight Finish, then press the Enter button. note For specific details about your network, please consult your network administrator. If you’re using AirPort, start the AirPort Admin utility, select your base station and click Configure. Then click the Network tab to see your base station’s IP address.
Selecting Wireless Network Settings in Mac OS Before connecting to the projector, select the correct wireless network on your computer. 1. Click the AirPort icon on the menu bar at the top of the screen. 2. Make sure AirPort is turned on, then do one of the following: ■ If your projector is set up on an existing network (Advanced mode), select the network name (SSID). ■ If your projector is configured for Quick mode, select the SSID you assigned to the projector.
3. Choose Wireless LAN and press Enter. You see this screen: 4. Select To Setup Wizard, then press Enter. You see the WPS (Wi-Fi Protected Setup) connection screen: 5. For the Push Button Method, follow the instructions on page 87. For the PIN Code Method, follow the instructions on page 88.
Using the Push Button Method 1. Select Push Button Method and press Enter. You see this screen: 2. Press the Enter button on the projector. 3. When prompted by the screen, press the WPS button on the access point. You see a message that WPS setup is complete. 4. Press the Enter button or the Esc button to return to the wireless LAN setting page.
5. Select Setup Complete and press Enter. 6. Make sure Yes is selected and press Enter. 7. Press the Menu button. Using the PIN Code Method Before you can make a connection using the PIN Code Method, a connection must have already been established between the computer and the access point. For details on how to make this connection, refer to the manual provided with the access point. 1. Follow steps 1 through 4 beginning on page 85 to access the WPS Connection Screen.
2. Select PIN Code Method and press Enter. You see this screen: 3. From the computer, enter the displayed PIN code for the access point, select Start Setup and then press Enter. You see a progress meter on the screen. 4. When you see a message that WPS Setup is complete, press the Enter or Esc button.
5. When you see the wireless LAN setting page, select Setup Complete and press Enter. You see this screen: 6. Select Yes and press Enter to save the settings. 7. Press the Menu button and then close the configuration menu to exit. Using Wireless Security Options If you have installed the optional Wireless 802.
Enabling WEP Encryption 1. Press Menu, then highlight Network and press Enter. 2. Choose Network Configuration and press Enter. 3. Highlight Security and press Enter. Then press Enter again to display the security options: 4. Highlight WEP and press Enter. 5. For the WEP encryption setting, highlight 128Bit or 64Bit and press Enter. 6. For Format, highlight ASCII to enable text input or HEX to enable hexadecimal input. Then press Enter. 7. If you chose 64Bit, choose Key ID 1, 2, 3, or 4.
note Text input for WEP encryption varies with different access points; check with your network administrator. Try ASCII first. If that doesn’t work, try Text2 and then Text3. Highlight the Encryption key text box that corresponds to the Key ID you selected, then press Enter. Press the pointer button to select individual letters, then press Enter to input a character. To navigate backward and forward through the input text, highlight the arrows and press Enter.
Enabling WPA Security 1. Press Menu, then highlight Network and then press Enter. 2. Choose Network Configuration and press Enter. 3. Highlight Security and press Enter. Then press Enter again to display the security options: 4. Choose WPA-PSK(TKIP/AES) or WPA2-PSK(TKIP/AES) and press Enter. Highlight the PSK (pre-shared key) text box and press Enter. Press the pointer button to select individual letters, then press Enter to input a character.
Enabling EAP, LEAP, or PEAP Authentication 1. Press Menu, then highlight Network and then press Enter. 2. Choose Network Configuration and press Enter. 3. Highlight Security and press Enter. Then press Enter again to display the security options: note You can enter up to 32 characters when you use the projector’s menu. If you enter the user name and password using a web browser (see page 101), you can enter up to 64 characters. 94 4.
Highlight the Password text box and press Enter. Enter the password as you entered the User name. 6. When you’re done making these settings, select Return, Setup complete, and then Yes to confirm that you want to save the changes. 7. Press Menu to exit. Enabling EAP-TLS Certificate Validation Once you have created an EAP-TLS certificate, follow the steps below to enable it. (Contact your Network Administrator for more information on obtaining or creating the certificate.
6. Press Menu to exit. Enabling Data Encryption from EasyMP Network Projection When using the EasyMP Network Projection software, follow these steps to enable data encryption. 1. Click Set options on the main screen. 2. Click the General settings tab. 3. Select the Encrypt communications checkbox. 4. Click OK. For more information, see the EasyMP Network Projection Operation Guide.
Removing the Wireless 802.11g/b/a Module Follow these steps to remove the module from your projector. 1. If you’re running EasyMP Network Projection, click Disconnect on the control bar. Click Disconnect 2. Check the access light to make sure it isn’t flashing. caution Never remove the module while its access light is green or when projecting wirelessly. You may damage the module. Access light 3. Turn off the projector and unplug it.
4. Unscrew the module, then pull it out. Remove screw here Using Projector E-mail Alerts When this feature is enabled, the projector sends you an e-mail alert if it has any problems. note You can also set e-mail alerts from EasyMP Monitor (available for Windows only). See the EasyMP Monitor Operation Guide for more information. 98 1. Press the Menu button, select the Network menu, then press Enter. 2. Choose Network Configuration and press Enter.
3. Choose Mail, then press Enter. You see a screen like this: 4. Highlight On to receive e-mail notifications, then press Enter. 5. Enter the IP address for the SMTP server for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used: 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255). 6. Enter the SMTP server’s port number. The default value is 25. You can enter a numeric value from 1 to 65535. 7.
When the selected problem or warning occurs, an e-mail message is sent to the specified notification addresses. The subject line of the e-mail is EPSON Projector. The e-mail includes the following information: ■ Line 1: The name of the projector where the problem has occurred ■ Line 2: The IP address of the projector where the problem has occurred ■ Line 3: Details of the problem 11.
4. Turn on the SNMP setting. 5. Enter up to two IP addresses for notification. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used: 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255). 6. For Priority Gateway, select Wired or Wireless. 7. If your network environment uses an AMX controller, select On to allow the projector to be detected by AMX Device Discovery. 8.
4. Select one of the menu options listed on the screen, then change any of the settings as needed. These settings correspond to those found in the projector’s menu system.
From the Projector Control menu, select Web Remote. You see the following screen: Power button Search button Video button Computer button BNC button Pause button A/V Mute button Page-up/down buttons LAN/USB button S-Video button HDMI/DVI-D button Volume buttons Closed captioning button ■ The Power button turns the projector on and off. ■ The Search button searches for signal sources (see page 56).
■ The A/V Mute button temporarily turns off the picture and sound (see page 67). ■ The Pause button stops the image (see page 67). ■ The Volume buttons raise or lower the volume. ■ The Page-up/down buttons change slides when you project a slideshow over a network or from a device connected to the USB port. ■ The CC (Closed Captioning) button lets you display closed captioning for content that provides it.
3. Choose Others and press Enter. You see the following screen: 4. Turn on the RoomView setting. 5. Highlight the Return button at the top of the screen, then press Enter. Choose Setup complete and press Enter, then choose Yes and press Enter to save the changes. 6. Press Menu to exit. 7. Turn the projector off and then on again. The setting change will take effect once the projector restarts.
note 2. Open your web browser and enter the IP address of the projector you want to monitor in the browser’s address box. You see a window like this: If you’re not sure what the IP address of the projector is, turn the projector on and select Net. Info.-Wired LAN or Net. Info.-Wireless LAN from the Network menu to display the address. Do not enter leading zeroes. toolbar 3. Select options on the screen as necessary: ■ To turn the projector on or off, click the Power button.
■ To adjust the image sharpness, click the Sharpness button in the toolbar. ■ To enlarge the image without changing the projection size, click the Zoom button in the toolbar. Then click the button to enlarge the image or the button to reduce an image that was enlarged with the button. Click the arrow buttons the change the position of an enlarged image. 4.
Using the Tools Tab Select the Tools tab in the top right corner of the window to display the window shown below: 1. Enter settings for Crestron® central controllers in the Crestron Control section of the window. 2. Enter settings in the Projector section of the window: ■ Enter a Projector Name to differentiate the current projector from other projectors on the network (up to 15 single-byte alphanumeric characters).
4. To require a password for access to the initial Crestron RoomView window, click Enable in the User Password section of the window, enter a password (in both the New Password and Confirm boxes), and click Send. 5. To require a password for access to the Tools tab, click Enable in the Admin Password section of the window, enter a password (in both the New Password and Confirm boxes), and click Send.
Using the Projector on a Network
5 5 Fine-Tuning the Projector You can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options Menu list The menus are listed on the left and the options available for the highlighted menu are shown on the right. note For a complete list of menus and options, see page 129.
4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the Enter button to view a sub-screen for changing the setting. ■ Press the left or right side of the a slider bar. pointer button to adjust ■ To select from two or more settings, use the pointer button to highlight the desired setting and press Enter. 5.
Adjusting the Image You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast. 1. Press the Menu button on the projector or remote control and select the Image menu. You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.) Computer/RGB Video/ USB/LAN note The available settings vary depending on the input source selected. Component Video/ Composite Video/ S-Video 2.
■ ■ Sharpness Adjusts the sharpness of the image. note If you select Advanced, you can access more detailed settings: Adjust Thin Line Enhancement to enhance or soften objects like hair or fabric patterns. Adjust Thick Line Enhancement to enhance or soften outlines of objects or backgrounds. Adjust Vert. Line Enhancement to enhance vertical lines in the image. Adjust Horiz. Line Enhancement to enhance horizontal lines in the image.
5. Use the pointer button to adjust the hue, saturation, and brightness. You see the adjustments reflected on the screen. When you are satisfied with the color, press Esc. 6. Repeat steps 4 and 5 for each color axis you want to adjust. You may need to readjust the color as the lamp in your projector changes over time. Adjusting Signal Settings Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments.
■ Resolution Set to Auto to have the projector automatically identify the resolution of the input signal. If necessary (because some of the image is missing, for example), adjust to Wide or Normal. You can also select Manual and specify a resolution. ■ Tracking Adjust this value to eliminate vertical stripes in computer images. ■ Sync Adjust this value if computer images appear blurry or flicker.
■ Input Signal If the colors don’t look right on the Auto setting, select the setting for the type of equipment you’ve connected to the Computer1, Computer2 (G5550NL/G5650WNL/ G5950NL only), or BNC ports. Choose RGB for a computer or RGB-video connection, and Component for a video player that outputs a component video signal (with connectors labeled Y/Cb/Cr or Y/Pb/Pr). ■ Video Signal Select the setting for the type of equipment you’ve connected to the Video1, Video2, or S-Video ports.
Customizing Projector Features You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features. ■ Keystone Adjusts the shape of the image if the projector has been tilted upward or placed at an angle to the screen. Select H/V-Keystone to correct horizontal and vertical keystone distortion. Select Quick Corner to adjust the shape and position of the projected image.
■ note You can also adjust the volume using the remote control. Volume Raises or lowers the volume. ■ Audio Input Lets you select the input port to use for audio when your video input is LAN. With the PowerLite G5550NL/G5650WNL/ G5950NL, you can also select an audio input port when your video input is HDMI. ■ Remote Receiver Deactivates the projector’s front and/or back sensors that detect signals from the remote control.
Using the Projector Security Features To prevent unauthorized use of the projector, you can do the following: note You can also attach a security cable to the projector to prevent theft (see page 164). ■ Assign a password. You can use the password to prevent the projector from being turned on, prevent your custom startup screen from being changed, and lock network settings. ■ Create a custom screen that is displayed at startup and/or when the A/V Mute button is pressed.
4. Hold down the Num button on the remote control and use the numeric keypad to enter a four digit password. (The default setting is 0000.) 5. When you see a confirmation message, reenter the password. Then press the Menu button to exit the screen. To set security options, access the Password Protect screen as described on page 121, and then turn on any of the following options: Hold down ■ Power On Protect to prevent unauthorized use of the projector.
If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked. Request code xxxxx. Write down the request code. The message displays for approximately 5 minutes, and then the projector switches to standby mode. Once the projector is in standby mode, disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.
2. Highlight User’s Logo and press Enter. 3. When you see a message asking Choose this image as the User’s Logo?, select Yes and press Enter. A selection box displays over the image. 4. Use the pointer button on the remote control (or the arrow buttons on the projector) to select the area of the image you want to use. Then press Enter. 5. When you see the message Select this image?, highlight Yes and press Enter. 6. Highlight a zoom factor (display size) and press Enter. 7.
3. Choose from these display options: note ■ Set Display Background to Logo to display your image when there is no signal. ■ Set Startup Screen to On to display your image when the projector is warming up. ■ Set A/V Mute to Logo to display your image when you press the A/V Mute button. You can lock these settings to prevent them from being changed without a password (see page 121). 4. When you’re finished, press Menu to exit.
Customizing Power and Operation You can use the Extended menu to customize the way the projector displays images, enable quick startup, turn sleep mode on or off, and customize other projector operations. ■ Display Use this setting to turn off the display of messages, change the background color, enable logo display, or turn off the startup screen display. With the PowerLite G5450WUNL/ G5750WUNL, you can also increase the size of the projector menus and messages.
Sleep Mode: Enable if you want the projector to turn off automatically if it is idle and no signal is received for 1 to 30 minutes (you can adjust the amount of time using the next setting). Sleep Mode Timer: When Sleep Mode is on, you can set the period of time before the projector turns off automatically, from 1 to 30 minutes. High Altitude Mode: Enable when you are using the projector above 4,900 feet (1,500 meters) to ensure that the temperature is regulated properly.
■ Multi-screen Use this option if you want to color-match two or more projectors that are being used to display images near each other, or you are using the multi-screen feature to project from one source (one image) with multiple projectors (see the EasyMP Network Projection Operation Guide). You can make image adjustments at each of five adjustment levels.
5. Next, adjust the brightness of Level 5 for the same two projectors. Match the brighter projector to the darker one. 6. Adjust and match the brightness of Levels 2, 3, and 4. 7. Adjust and match the G/R color correction for all levels. Then adjust and match the B/Y correction for all levels. 8. If you are using three or more projectors, repeat steps 4 through 7 to match projector 3 to projector 2, then match projector 4 to projector 3, and so on.
Menu Options Signal Auto Setup Resolution Tracking Sync.
Menu Options Info Lamp Hours Source Input Signal Resolution Video Signal Refresh Rate Sync Info Status Serial Number Event ID Reset Reset All Reset Lamp Hours Fine-Tuning the Projector 131
Fine-Tuning the Projector
6 6 Maintaining the Projector Y our projector needs little maintenance. All you have to do is keep the lens clean. You may also need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens caution Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged. Clean the lens whenever you notice dirt or dust on the surface. To remove dirt or smears on the lens, use a commercially available cloth for cleaning glasses. Cleaning the Projector Case caution Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case. Before you clean the case, turn off the projector and unplug the power cord.
Follow these steps: 1. Press the Ppower button on the back of the projector to turn it off. After the projector beeps twice, unplug the power cord. 2. Grip the air filter cover tab and remove the air filter cover as shown. 3. Place your finger into the groove and remove the air filter as shown.
4. With the front of the air filter facing down, tap it four or five times to shake off the dust. Turn it over and tap the other side in the same way to shake off the dust. 5. To clean any dust remaining on the air filter, use a small vacuum cleaner designed for computer and other office equipment to clean the front. If you don’t have one, gently clean the vent with a soft brush (such as an artist’s paintbrush). 6. Insert the air filter back into the holes in the cover, then press it firmly into place.
7. Slide the air filter cover in until it clicks into place. 8. If the dirt is difficult to remove, the filter is broken or discolored, or you continue to see air filter related messages even after cleaning, replace the filter as described in the next section. Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766) to obtain a new filter. Replacing the Air Filter Follow these steps to replace the air filter: 1. Press the Ppower button on the back of the projector to turn it off.
3. Place your finger into the groove and remove the air filter as shown. note The air filter contains Polypropylene. Dispose of used air filters properly in accordance with your local regulations. 4. Insert the new air filter into the holes in the cover, then press it firmly into place. 5. Slide the air filter cover in until it clicks into place. note Turn off this product when not in use to prolong the life of the projector. Do not turn the projector on immediately after turning it off.
It is time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate. ■ The message Replace the lamp appears on the screen when the lamp comes on. ■ The Lamp light flashes orange. note To maintain projector brightness and image quality, replace the lamp as soon as possible. You may also need to replace the lamp if the red. See page 147. Epson recommends that you clean the air filter whenever you replace the lamp.
3. Loosen the lamp cover screws (you don’t need to remove them). Then remove the lamp cover. note Even when the lamp cover is removed, it is still attached to the projector to prevent it from falling when the projector is mounted on the ceiling. 4. Loosen the two screws holding the lamp in place (you can’t remove them). Loosen, but don’t remove these screws note The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling.
7. Once the lamp is fully inserted, tighten its screws. 8. Replace the lamp cover, then tighten its screws. 9. Reset the lamp timer as described in the next section. Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menu. 1. Press the Menu button on the remote control or on the projector’s control panel. You see the main menu. 2.
5. When you’re finished, press Menu to exit. Checking Lamp Usage note The information displayed depends on the input signal currently selected. To check the number of hours the lamp has been used, press the Menu button and highlight the Info menu. You see a screen like this: caution When replacing batteries, take the following precautions: ■ Replace the batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash immediately.
3. Install two AA alkaline batteries, inserting the + and – ends as shown. 4. Position the cover as shown, then press down until it snaps into place. Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent damage: note ■ If you are moving the projector by hand, use the projector handle. ■ Attach the lens cover to the lens. ■ Return the projector feet to their stored (highest) positions.
Maintaining the Projector
7 7 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on the back of the projector or on the remote control. 1. Press the ? Help button on the remote control or on the projector. You see the Help menu: 2. Use the pointer button on the remote control or the navigational buttons on the projector to highlight menu items. 3. Press the Enter button on the remote control or on the projector to select the menu item. 4.
Checking Projector Status If your projector isn’t working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status.
Status lights (continued) Light Status Description Flashing orange The projector is cooling down. You can’t turn it back on (and you should not unplug it) until the light stops flashing and remains orange. The projector is setting itself up for network monitoring. Flashing green The air filter may be clogged. Clean or replace the air filter as described on pages 134 to 138. Red or flashing red There is a problem with the projector.
Status lights (continued) Light Status Description Flashing red There is a problem with the fan or temperature sensor. Stop using the projector, disconnect the power cord, and contact Epson as described on page 161. Flashing red The lamp may be burnt out. First make sure the lamp cover is securely installed. If that’s not the problem, the air filter may be clogged. Clean or replace the air filter as described on pages 134 to 138.
The buttons on the projector don’t work. If the Control Panel Lock function has been enabled, you can’t use the buttons on the projector. Try using the remote control instead (make sure it is set to the correct ID). See page 125 for information about the Control Panel Lock function. Solving Problems With the Image or Sound No image appears on the screen. ■ Check that the Ppower light is green, not flashing, and that the lens cover is removed. ■ The projector may be in standby or sleep mode.
■ If you’ve connected more than one computer and/or video source, you may need to press the Source Search button on the projector’s control panel, or the Search button or one of the Source buttons on the remote control to select the correct source. (Allow a few seconds for the projector to sync up after pressing the button.) ■ Make sure the power for your connected equipment is turned on.
The message Not Supported is displayed. ■ Make sure the correct input signal is selected in the Signal menu (see page 116). ■ Make sure your computer’s resolution and frequency or refresh rate is supported by the projector (see page 174). If necessary, change your computer’s settings.
3. Click Detect Displays. 4. Do one of the following: Mac OS X 10.6.x users: Click Show displays in menu bar. Other Mac OS X users: Make sure the VGA Display or Color LCD dialog box is selected, click the Arrangement or Arrange tab, then make sure the Mirror Displays checkbox is selected. Only part of the computer image is displayed. ■ Press the Auto button on the remote control or the Enter button on the projector. ■ Make sure the image Position setting is correct in the Signal menu.
■ If you’re using a computer cable longer than 6 feet (1.8 meters), or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables away from the power cord as much as possible to prevent interference. ■ The video signal may be split between the computer and the projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your notebook computer and the projector, turn off the notebook’s LCD display.
■ Make sure the projector is within the proper range (projection distance) from the screen (see page 170). ■ Make sure the lens is not fogged by condensation. You may need to wait before using the projector after moving it from a cold environment to a warm environment. ■ If you’re projecting from a computer, you may need to adjust the tracking and sync settings as described in the next section. You see vertical bands or the image still looks blurry after trying the solutions in the previous section.
The image is too light or dark, or colors are incorrect. note Because of the different technologies used, your projected image may not exactly match the colors on your notebook or computer monitor. ■ Use the Color Mode option in the projector’s Image menu to adjust the color (see page 114). ■ If you’re displaying video, adjust the Color Adjustment and Color Mode settings on the Image menu. You can also try adjusting the Color Saturation, ABS Color Temp, and Tint settings on the Image menu.
■ If you’re using a computer audio cable, make sure it is connected to your computer’s headphone jack or audio out jack. Connect the other end to the projector as described on page 46. ■ If you’re using an HDMI cable and you hear no sound, set your equipment to PCM output. ■ If your equipment is connected through the LAN port, or the HDMI port with the PowerLite G5550NL/G5650WNL/ G5950NL, make sure you’ve set the Audio Input setting correctly. See page page 119.
■ Make sure the projector is plugged in. ■ Make sure the LAN cable is connected correctly. Reconnect it if it is not connected or it is not connected correctly (see page 76). For problems with the EasyMP Network Projection software, see the EasyMP Network Projection Operation Guide. For problems with the EasyMP Multi PC Projection software, see the EasyMP Multi PC Projection Operation Guide. For problems with EasyMP Monitor (available for Windows only), see the EasyMP Monitor Operation Guide.
Event ID Description 0893 There is a problem related to WEP, TKIP, or AES encoding. Check the setting wireless LAN security setting in the projector (page 93). 0894 There was a network communication problem because a connection was made to the wrong access point. Consult your network administrator. 0898 Failed to obtain DHCP settings. Check the DHCP server to make sure it is operating correctly. Turn off DHCP in the projector if it is not being used.
Solving Problems With the Remote Control The projector doesn’t respond to remote control commands. 160 Solving Problems ■ Point the remote control towards the receiver. ■ Make sure the projector and remote control IDs match. To operate all projectors by remote control regardless of ID settings, set the ID switch on the side of the remote control to Off. ■ The remote control’s batteries may not be installed correctly or may be low on power. To change the batteries, see page 142.
Where to Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website at www.epson.com/support for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card.
■ Description of the problem You can obtain the serial number from the projector’s menu system: Just press the Menu button and highlight the Info menu. Purchase Supplies and Accessories You can purchase screens and other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
A A Projector Installation This appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt the projector down to position the image on the screen. This causes the image to lose its square shape. You can correct the image using the projector’s Quick Corner and/or Keystone functions, as described on page 58. Security Features The projector includes security features to prevent its theft when installed or used in public locations: ■ Security cable attachment.
■ Lens theft deterrent screw. You can lock the lens with the supplied screw, so that the lens cannot be removed. In addition, the projector includes several menu-operated security features. See page 121. Installing and Removing the Cable Cover Install the rear cable cover to enhance the appearance of the projector and prevent any cables from being loosened or removed. To install the cover, follow these steps: 1. Insert its tabs into the slots as shown, then push the cover against the projector.
2. Tighten the screws at the bottom of the cover. 3. To remove the cover (when connecting or disconnecting cables), loosen the screws on the bottom of the cover, pull the bottom of the cover away from the projector as shown. Installing and Removing the Lens See the following sections for instructions on installing and removing the lens. Installing the Lens 1. Turn off the projector and unplug the power cord.
2. Turn the focus ring clockwise until it stops moving. note Only install or remove the lens when necessary. If dust enters the projector, projection quality may deteriorate and/or the projector may malfunction. 3. Make sure the white dot on the lens is facing up. Insert the lens straight into the projector, then turn clockwise until you hear it click into place. white dot Do not install or remove the lens when the projector’s lens insertion section is facing up. Dust could enter the projector.
3. Hold down the lens removal button and turn the lens counterclockwise until you hear it click. 4. Remove the lens by pulling it straight out.
B B Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) PowerLite Pro G5550NL/G5950NL: 1024 × 768 pixels (XGA) PowerLite Pro G5650WNL: 1280 × 800 pixels (WXGA) PowerLite Pro G5450WUNL/G5750WUNL: 1920 × 1200 pixels (WUXGA) Color reproduction 16.
Contrast ratio Image size (includes all lenses) Projection distance (includes all lenses) PowerLite Pro G5450WUNL/G5550NL: 1000:1 PowerLite Pro G5750WUNL: 1500:1 PowerLite Pro G5650WNL/G5950NL: 2000:1 PowerLite Pro G5450WUNL/G5750WUNL (16:10 image): 50 to 300 inches (127 to 762 centimeters) PowerLite Pro G5650WNL (16:10 image): 30 to 300 inches (76.2 to 762 centimeters) PowerLite Pro G5550NL/G5950NL (4:3 image): 30 to 300 inches (76.2 to 762 centimeters) PowerLite Pro G5450WNL/G5750WUNL (16:10 image): 2.
Keystone correction PowerLite Pro G5450WUNL/G5750WUNL: vertical, ±20° horizontal (standard lens) PowerLite Pro G5550NL/G5650WNL/G5950NL: ±40° vertical, ±20° horizontal (standard lens) ±30° Mouse compatibility Requires optional Wireless IR Mouse Receiver (part number V12H007T16) Projection Lamp note Lamp life will vary depending upon mode selected, environmental conditions, and usage. Brightness decreases over time. Turn off this product when not in use to prolong the life of the projector.
Electrical Rated frequency 50/60 Hz AC Power supply Powerlite Pro G5450WUNL: 100/240 VAC, 4.2 A/1.8 A Powerlite Pro G5550NL: 100/240 VAC, 3.9 A/1.7 A PowerLite Pro G5650WNL/G5950NL: 100/240 VAC, 4.7 A/2.0 A Powerlite Pro G5750WUNL: 100/240 VAC, 4.8 A/2.
PowerLite Pro G5650WNL/G5950NL: Operating: 100 to 120 VAC 464 W (Normal Power Consumption mode) 383 W (ECO Power Consumption mode) 220 to 240 VAC 442 W (Normal Power Consumption mode) 367 W (ECO Power Consumption mode) Standby: 100 to 120 VAC 0.38 W (Communication off) 10 W (Communication on) 220 to 240 VAC 0.
Operating altitude 0 to 9,800 ft (0 to 3,000 m) (over 4,900 ft/1,500 m, with High Altitude Mode active) Safety and Approvals United States FCC 47CFR Part 15B Class B (DoC) UL60950-1 Second Edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No. 60950-1-07 (cTUVus Mark) Pixelworks™ DNX™ ICs are used in this projector.
Computer signals (analog RGB) (continued) Mode Refresh Rate (Hz) Resolution SXGA1—70 SXGA1—75 SXGA1—85 70 75 85 1152 × 864 1152 × 864 1152 × 864 WXGA—60 WXGA—75 WXGA—85 60 75 85 1280 × 800 1280 × 800 1280 × 800 SXGA2—60 SXGA2—75 SXGA2—85 60 75 85 1280 × 960 1280 × 960 1280 × 960 SXGA3—60 SXGA3—75 SXGA3—85 60 75 85 1280 × 1024 1280 × 1024 1280 × 1024 WXGA1—60 WXGA2—60 60 60 1280 × 768 1360 × 768 WXGA+60 WXGA+75 WXGA+85 60 75 85 1440 × 900 1440 × 900 1440 × 900 SXGA+60 SXGA+75 60 75 140
Component video Mode Refresh Rate (Hz) Resolution TV525i (480i) TV625i (576i) SDTV525p (480p) SDTV625p (576p) HDTV750p (720p) HDTV750p (720p) HDTV1125i (1080i) HDTV1125i (1080i) 60 50 60 50 60 50 60 50 720 × 480 720 × 576 720 × 480 720 × 576 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 Mode Refresh Rate (Hz) Resolution NTSC NTSC 4:43 PAL N-PAL M-PAL PAL—60 SECAM 60 60 50 50 60 60 50 720 × 480 720 × 480 720 × 576 720 × 576 720 × 576 720 × 576 720 × 576 Composite video/S-Video Signals input thro
Signals input through the DVI-D (G5450WUNL/G5750WUNL only) or HDMI ports (continued) Mode Refresh Rate (Hz) Resolution TV525i (480i) TV625i (576i) SDTV525p (480p) SDTV625p (576p) HDTV750p (720p) HDTV750p (720p) HDTV1125i (1080i) HDTV1125i (1080i) HDTV1125p (1080p) HDTV1125p (1080p) HDTV1125p (1080p) HDTV1125p (1080p) 60 50 60 50 60 50 60 50 60 50 30 24 720 × 480 720 × 576 720 × 480 720 × 576 1280 × 720 1280 × 720 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 1920 × 1080 * Available only
Technical Specifications
C C Notices T his appendix includes safety instructions and other important information about your projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not look into the lens when the projector is on. The bright light can damage your eyes, and is especially dangerous for children and pets. ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not operate the projector on its side, or while tilted to one side.
Notices ■ Do not use sprays containing flammable gas to clean the lens or filter. Do not spray a liquid of any kind directly on the projector or its lens. Do not use the projector where there may be flammable, explosive, or corrosive gases present in the atmosphere. ■ Do not place containers of liquid on top of the projector. Never spill liquid of any kind into the projector. ■ Do not use the projector where it may be exposed to smoke, steam, or excessive dust.
distinct change in performance; if smoke, strange odors, or strange noises come from the projector; if the power cord or plug is damaged or frayed; if liquid or foreign objects get inside the projector, or if it has been exposed to rain or water; if it has been dropped or the housing has been damaged. ■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel.
■ Never try to remove the lamp immediately after use because it will be extremely hot. Before removing the lamp, turn off the power and wait at least an hour to allow the lamp to cool completely. ■ Do not place the source of an open flame, such as a lit candle, on or near the projector. ■ Do not modify the power cord. Do not place heavy objects on top of the power cord or bend, twist, or pull it excessively. Keep the power cord away from hot electrical appliances.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Software Copyright This product uses free software as well as software to which this company holds the rights. The following is information on the free software used by this product. 1. LGPL (1) This company uses free software for this product under the terms of the GNU LESSER General Public License Version 2, June 1991(henceforth "LGPL") or later versions. You can see the full text of the LGPL on the following Web sites. [LGPL]http://www.gnu.org/licenses/gpl.
Copyright© 1996-1997 Andreas Dilger Copyright© 1995-1996 Guy Eric Schalnat, Group 42, Inc. (2) zlib Copyright© 1995-2003 Jean-loup Gailly and Mark Adler GNU GPL This projector product includes the open source software programs which apply the GNU General Public License Version 2 or later version ("GPL Programs"). We provide the source code of the GPL Programs until five (5) years after the discontinuation of same model of this projector product.
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation's software and to any other program whose authors commit to using it.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it. 6.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number.
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms. To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the "copyright" line and a pointer to where the full notice is found.
GNU LGPL This projector product includes the open source software programs which apply the GNU Lesser General Public License Version 2 or later version ("LGPL Programs"). We provide the source code of the LGPL Programs until five (5) years after the discontinuation of same model of this projector product. If you desire to receive the source code of the LGPL Programs, please contact the customer support of your region.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it. For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
1. You may copy and distribute verbatim copies of the Library's complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
6. As an exception to the Sections above, you may also combine or link a "work that uses the Library" with the Library to produce a work containing portions of the Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer's own use and reverse engineering for debugging such modifications.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute. 7.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU.
Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a library for tweaking knobs) written by James Random Hacker.
THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
This software is copyright (C) 1991-1998, Thomas G. Lane. All Rights Reserved except as specified below.
The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the Unisys LZW patent, GIF reading support has been removed altogether, and the GIF writer has been simplified to produce "uncompressed GIFs". This technique does not use the LZW algorithm; the resulting GIF files are larger than usual, but are readable by all standard GIF decoders. We are required to state that "The Graphics Interchange Format(c) is the Copyright property of CompuServe Incorporated.
There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user. libpng versions 0.97, January 1998, through 1.0.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated. A "png_get_copyright" function is available, for convenient use in "about" boxes and the like: printf("%s",png_get_copyright(NULL)); Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.
Jean-loup Gailly jloup@gzip.org Mark Adler madler@alumni.caltech.edu If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code. If you redistribute modified sources, we would appreciate that you include in the file ChangeLog history information documenting your changes.
The original and principal author of md5.h is L. Peter Deutsch . Other authors are noted in the change history that follows (in reverse chronological order): 2002-04-13 lpd Removed support for non-ANSI compilers; removed references to Ghostscript; clarified derivation from RFC 1321; now handles byte order either statically or dynamically. 1999-11-04 lpd Edited comments slightly for automatic TOC extraction.
For embedded multimedia software: This product contains embedded multimedia software licensed from Ingenient Technologies, Inc. (www.ingenient.com). Copyright© 2000-2007 Ingenient Technologies, Inc. All rights reserved.
Notices
Index A A/V Mute button, 67 display settings, 125 Access Point mode, 82 Accessories, 15 to 16 Ad Hoc mode, 81 Air filter cleaning, 134 to 137 ordering, 15 replacing, 137 to 138 Altitude, 127, 148, 149, 174 Anti-theft device, 15, 30, 164 to 165 Aspect ratio, 170 Audio connecting equipment, 46 to 49 controlling volume, 68 problems, troubleshooting, 156 to 157 turning off (using A/V Mute), 67 Audio Input setting, 120 Authentication, 94 to 95 Auto Setup setting, 116 B Background screen settings, 125 Bands, ver
Connecting projector to audio equipment, 46 to 49 to computer, 30 to 35 to digital camera, 50 to 51 to external monitor, 45 to speakers, 49 to video equipment, 36 to 44 Contrast setting, 114 Control Panel Lock setting, 119, 125 Crestron RoomView, 104 Custom screen, see User’s Logo Customized color mode, 61 D Data encryption, 96 Default settings, restoring, 113 DICOM SIM color mode, 61 Digital camera connecting to, 50 to 51 Direct Power On, 53 Distance from projector to screen, 19, 170 Documentation, 13 to
Infrastructure mode, see Access Point mode Input Signal setting, 118 Input signal, selecting, 56, 66 Installing cable cover, 166 projector, 163 to 164 Instant Off, 54 K Kensington anti-theft device, 15, 30, 164 Keystone correction, 58 to 60, 119, 153, 171 Keyword, 81 L Lamp number of hours used, 142 ordering, 15 replacing, 138 to 142 specifications, 171 status light, 147 to 149 Lamp timer, resetting, 141 to 142 Language setting, 128 Laptop computer connecting to, 34 to 35 display problems, 150 to 153 sele
P Password protection, 121 to 123 remote access, 81 request code, 123 PEAP authentication, 94 to 95 Photo color mode, 60 Picture source, selecting, 56, 66 Picture, see Image PIN code method, 85, 88 to 90 Pointer shape, 119 Pointer tool, using, 69 Positioning image, 57 to 58 projector, 19 to 30, 163 to 164 Power button, 53 specifications, 172 status light, 53, 147 to 149 Power consumption, 119 Presentation color mode, 60 Presentations computer, 30 to 35 digital camera, 50 to 51 room conditions, 19, 66 using
Remote control A/V Mute button, 67 as wireless mouse, 70 battery used, 171 controlling multiple projectors, 71 to 73 correcting color, 60, 114 to 116 E-Zoom button, 68 Freeze button, 67 ID, 72 to 73 numeric keypad, using, 122 pointer tool, using, 69 problems, 160 range, 171 specifications, 171 switching sources, 66 troubleshooting, 160 virtual over network, 102 Remote Receiver setting, 120 Removing wireless module, 97 Replacing lamp, 138 to 142 Request code, password, 123 Resetting lamp timer, 141 to 142 Re
Tint setting, 114 Tracking, adjusting, 155 Transporting projector, 143 Troubleshooting blank screen, 150 to 152 cut-off image, 153 distorted image, 58 to 60 EasyMP Monitor problems, 158 EasyMP Multi PC Projection problems, 158 EasyMP Network Projection problems, 158 image and sound problems, 150 to 157 network problems, 157 to 158 no signal, 150 to 151 projector problems, 145 to 162 remote control problems, 160 tapered image, 58 to 60 Turning off picture (using A/V Mute), 67 Turning off projector, 54 U Unp
