PowerLite Pro G5150NL/G5350NL/G5200WNL Multimedia Projector ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
C Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 10 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 11 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 1 Setting Up the Projector . . . . . . . . . . . . . . . . . . . . .
Turning the Projector On and Off . . . . . . . . . . . . . . . . . . . . 37 Using the Direct Power On Function . . . . . . . . . . . . . . 39 Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . 40 4 2 Displaying and Adjusting the Image . . . . . . . . 41 Displaying an Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Troubleshooting Display Problems. . . . . . . . . . . . . . . . . . . . 42 You Can’t Project an Image . . . . . . . . . . . . . . . . . . . . . .
4 Preparing the Projector to Present Through a Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Configuring Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Configuring a Wireless Connection . . . . . . . . . . . . . . . . . . . 62 Using Ad Hoc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Using Access Point Mode. . . . . . . . . . . . . . . . . . . . . . . . 69 Making a WPS (Wi-Fi Protected Setup) Connection . . .
6 Managing Projectors. . . . . . . . . . . . . . . . . . . . . . . . 113 Connecting to a Wired Network . . . . . . . . . . . . . . . . . . . . 114 PowerLite Pro G5150NL and G5350NL. . . . . . . . . . . 114 PowerLite Pro G5200WNL. . . . . . . . . . . . . . . . . . . . . 115 Using Projector E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . 116 PowerLite Pro G5150NL and G5350NL. . . . . . . . . . . 116 PowerLite Pro G5200WNL. . . . . . . . . . . . . . . . . . . . .
A Projector Installation . . . . . . . . . . . . . . . . . . . . . . . 149 B Technical Specifications . . . . . . . . . . . . . . . . . . . . 155 C Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165 Installation Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149 Security Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 Installing the Cable Cover . . . . . . . . . . . . . . . . . . . . . . . . .
W - Welcome The PowerLite ® Pro G5150NL/G5350NL/G5200WNL is an easy-to-use, lightweight projector. It offers up to 4000 lumens (G5150NL), 4200 lumens (G5200WNL), or 5000 lumens (G5350NL) of brightness, and provides a native XGA (G5150NL and G5350NL) or WXGA (G5200WNL) resolution. You can connect it to a wide range of computers and video sources. You can project from a USB or SD™ storage device, or over a wired network (G5150NL and G5350NL only).
Additional enhancements: Closed captioning for the hearing impaired ■ HDMI for digital connectivity ■ 1000:1 (G5150NL and G5350NL) or 800:1 (G5200WNL) contrast ratio ■ With Windows Vista®, you can use the wireless Network Projector feature to quickly connect to the projector without installing any additional software (G5150NL and G5350NL only) ■ Color match images from up to four projectors for a uniform, wide-screen view ■ When you present with PowerPoint®, project only the slide images while vie
Getting More Information Need tips on giving presentations? Quick steps for setting up your projector? Here’s where you can look for help: ■ Quick Reference sheet Provides information for connecting the projector to your equipment, displaying and adjusting the image, using the remote control, and solving display problems.
Registration and Warranty Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure included with your projector. In addition, for customers who register their projector, Epson offers free Extra Care Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually via overnight delivery.
Product Part number Advanced projector ceiling mount with precision gear High security projector ceiling mount Adjustable suspended ceiling channel kit False ceiling plate kit Structural round ceiling plate Adjustable extension column (pipe) 6”–9” ELPMBPRG ELPMBATA ELPMBP01 ELPMBP02 ELPMBP03 ELPMBC01 Kensington security lock ELPSL01 50-inch portable screen (4:3 aspect ratio) 60-inch portable pop-up screen (4:3 aspect ratio) 80-inch portable pop-up screen (4:3 aspect ratio) DUET Portable Projector Scre
Welcome
1 1 Setting Up the Projector T his chapter tells you how to unpack the projector and connect it to a notebook or desktop computer, to video equipment, such as a VCR, DVD player, or video camera, and/or to your local area network. You can also connect the projector to a USB storage device or digital camera, or use it with an SD card (G5150NL and G5350NL only).
Unpacking the Projector After unpacking the projector, make sure you have all these parts: PDF manuals and registration CD-ROM Projector software CD-ROM Projector and lens cap Cable cover Remote control and 2 AA batteries Password Protected sticker Lens theft deterrent screw Power cord VGA computer cable note If you mount the projector on the ceiling, the interface and button names on the projector will appear upside down.
Additional Components Depending on how you plan to use the projector, you may need additional components: ■ To receive an HDMI signal from your video device, you’ll need an HDMI cable. One may be provided with your video equipment. ■ To receive a component video signal from a VCR or other video device, you’ll need a component video cable. One may be provided with your video equipment.
PowerLite Pro G5150NL/G5350NL (4:3 image) TBD 26.5 to 47.8 ft (8.1 to 14.6 m) 5.2 to 9.4 ft (1.6 to 2.9 m) 2.7 to 4.7 ft (0.8 to 1.4 m) Distance from screen PowerLite Pro G5200WNL (16:10 image) TBD 27.9 to 50.3 ft (8.5 to 15.3 m) 5.5 to 9.9 ft (1.7 to 3.0 m) 2.7 to 4.9 ft (0.8 to 1.5 m) Distance from screen Also keep these considerations in mind: 18 Setting Up the Projector ■ Place the projector on a sturdy, level surface.
Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be about level with the bottom of the screen. Projector note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector. You can purchase this from Epson; see page 12.
Connecting to the Computer Port You can connect to the projector using the VGA computer cable that came with it (the monitor port on your computer must be a mini D-sub 15-pin port). 1. If you’re using the VGA computer cable, connect one end to the projector’s Computer1 or Computer 2 port, and the other end to your computer’s monitor port. caution Don’t try to force a connector to fit a port with a different shape or number of pins. You may damage the port or connector. 2.
Connecting to the USB Port You can connect a Windows Vista, XP, or Windows 2000 (SP4) computer to the projector’s Type B (square) USB port and project your computer’s display (G5150NL and G5350NL only). A USB 2.0 connection provides better picture quality and response than USB 1.1. The first time you connect a computer to the projector’s USB port, software from the projector is installed on your computer. 1. Follow the instructions beginning on page 37 to turn on the projector. 2. Turn on your computer. 3.
After the software has been installed, you see your computer’s desktop displayed by the projector. You can switch the projector to other image sources using the Source buttons on the remote control, and then switch back to your desktop display by pressing EasyMP. 6. See Chapter 2 for instructions on displaying and adjusting the image. 7. When you’re done projecting from your computer, disconnect the USB cable. Connecting to the BNC Connectors 1.
4. You may need to change the Input Signal setting in the projector’s Signal menu to RGB (see page 99). 5. You can connect an optional stereo mini-jack audio cable to play sound through the projector (see page 32). With the optional wireless mouse receiver (see page 56), you can use the remote control as a mouse. 6. When you’ve finished making any connections, see page 37 for instructions on turning on the projector and Chapter 2 for instructions on displaying and adjusting the image.
Connecting to Video Equipment You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections: ■ If your video player has an HDMI connector, see “Connecting an HDMI Video Source” on page 25. HDMI connector ■ If your video player has a component video port (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), see “Connecting a Component Video Source” on page 28.
After connecting video cables, you may also want to connect an audio cable to play sound through the projector; see page 32. If you connect using an HDMI cable, the video and sound are both transferred and you won’t need to connect any additional cables for audio. Connecting an HDMI Video Source For best image quality, connect your video equipment to the HDMI (High-Definition Multimedia Interface) port, if possible. 1. Locate an HDMI cable. 2.
Connecting a Composite Video Source note If the video cable was not provided with your video device, you can purchase one from an electronics dealer. 1. If your video cable has an RCA connector, connect it to the yellow video output connector on your player and the yellow Video2 connector on the projector (as shown below). Or if your cable has a bayonet connector (BNC), connect it to the Video1 connector on the projector. 2.
Connecting an S-Video Source 1. Connect the S-video cable to the S-video connector on your player and the S-Video connector on the projector. note If the S-video cable was not provided with your video device, you can purchase one from Epson; see page 12. 2. If you want to play sound through the projector, see page 32 for instructions on connecting audio cables. 3.
Connecting a Component Video Source note If the component video cable was not provided with your video device, you can purchase one from an electronics dealer. 1. Look at the connectors at one end of your component video cable. If they are bayonet (BNC) connectors, go on to step 2. If they are RCA connectors, you’ll need to attach commercially available BNC adapters to plug the cable into your projector, then continue with step 2. 2.
Connecting an RGB Video Source Connecting Using a VGA Computer Cable 1. Locate the VGA computer cable provided with the projector. 2. Connect the cable to the video port on your player and the Computer1 or Computer2 port on the projector. note Be sure your video player is not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation. 3. You may need to change the Input Signal setting in the projector’s Signal menu to RGB (see page 99). 4.
Connecting Using a BNC Cable 1. Locate a BNC video cable (one may be included with your video equipment). 2. Connect the cable between your player and the corresponding R/G/B connectors on the projector. 3. You may need to change the Input Signal setting in the projector’s Signal menu to RGB (see page 99). 4. If you want to play sound through the projector, see page 32 for instructions on connecting audio cables. 5.
Connecting an External Monitor If you want to monitor your computer presentation close-up (on a monitor placed beside the projector) as well as on the screen, you can connect an external monitor. You can use it to check on your presentation even if you’ve pressed the A/V Mute button or switched to a different picture source. First make sure your computer’s VGA cable is connected to the projector’s Computer1, Computer2, or BNC ports (see page 20).
Playing Sound Through the Projector You can play sound through the projector’s speaker system or attach an external speaker system. To play sound through the projector, follow these steps: 1. Locate the appropriate cable and connect it to the Audio jack on the projector. ■ 32 Setting Up the Projector If you have equipment connected to the Computer1, Computer2, or BNC ports, use a stereo mini-jack cable. Connect the cable to the Audio port beneath the Computer2 port.
■ If you have equipment connected to the Video1, Video2, or S-Video ports, connect an RCA audio cable to the L and R Audio (Video) ports. 2. Connect the other end of the cable to the audio output connector(s) on your computer or video equipment.
Connecting External Speakers You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projector’s built-in speaker system is disabled. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter. 2.
Connecting to a Digital Camera or Other USB Device You can connect your digital camera, USB flash memory drive, USB hard drive, or multimedia storage viewer, such as the Epson P-5000 or Apple® iPod® to the PowerLite Pro G5150NL or G5350NL. Use the USB cable specified for your device. Then you can use your device’s slideshow function or the projector’s EasyMP (PC Free) feature. See the EasyMP Operation Guide for more information. 1. Follow the instructions beginning on page 37 to turn on the projector. 2.
Removing the USB Cable If you’re using PC Free mode to project your images, exit PC Free mode before you remove the USB device or cable from the projector. 1. Position the cursor over the Exit button in the upper right corner of the PC Free screen. 2. Press the Enter button on the remote control to close PC Free mode. 3. Turn off your digital camera or other device. 4. Disconnect the USB cable.
The indicator light above the slot comes on or flashes when the SD card is in use. Do not remove the card when the light is flashing. To remove the card, gently press the inserted SD card. The card springs out, and you can then remove the card by pulling it straight out. caution Do not remove the card when the indicator light is flashing, or you may damage the card or projector.
Follow these steps to turn on the projector: 1. Remove the lens cover. note You can set the projector to automatically turn off the lamp and enter “sleep mode” when it has not received any signals for 10 minutes (see page 107 to enable, disable, or adjust this setting). This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the P power button. If you are done using the projector, unplug the power cord. 2.
3. Press the Ppower button on the remote control or on the back of the projector. The projector beeps once and the Ppower light flashes green as the projector warms up, then an image begins to appear. When the Ppower light stops flashing and remains green, the projector is ready for use. 4. If you are prompted to enter a password, see page 103. warning Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.
Shutting Down the Projector note Lamp life results depend upon the Brightness Control setting you’ve selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. This projector incorporates Instant Off technology. To turn it off, you can press its Ppower button as described below, unplug it, or turn off a power switch that supplies power to the projector. You don’t have to wait for the projector to cool down first. 1.
2 2 Displaying and Adjusting the Image Follow the guidelines in this chapter for: ■ Displaying an image ■ Troubleshooting display problems ■ Adjusting the image 41
Displaying an Image You may need to select the image source if you have multiple video sources connected to the projector (such as a computer or DVD player). Selecting the image source lets you switch between images input from different pieces of connected equipment. If you don’t see the image you want, press the Search button or one of the Source buttons on the remote control, or the Source Search button on the projector until you see the image you want to project.
■ If you’ve connected more than one computer and/or video source, you may need to press the Source Search button on the projector’s control panel, or the Search button or one of the Source buttons on the remote control to select the correct source. (Allow a few seconds for the projector to sync up after pressing the button.) ■ If you’re using a PC notebook, press the function key on your keyboard that lets you display on an external monitor. It may be labeled CRT/LCD or have an icon such as .
If you’re using Mac OS X: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple® menu, select System Preferences, then select Displays. 2. Make sure the VGA Display or Color LCD dialog box is selected. 3. Click the Arrangement (or Arrange) tab. Make sure Mirror Displays is checked 4. Make sure the Mirror Displays checkbox is selected.
Adjusting the Position of the Image If the image is too low on the screen, you can use the front adjustable foot to raise it. 1. Stand behind the projector. Press the foot release lever up and lift the front of the projector. 2. Once the image is positioned where you want it, release the lever to lock the foot in position. 3. If necessary, you can fine-tune the height or level the image by turning any of the projector’s adjustable feet.
Additionally, you can use the vertical lens shift dial on the top of the projector to move your image up or down, or you can use the horizontal lens shift dial to move your image left or right. Vertical Horizontal Focusing and Zooming the Image Turn the focus ring on the projector to sharpen the image. Turn the zoom ring (using the knobs on the ring) to reduce or enlarge the image. Focus Zoom If the image still isn’t large enough, you may need to move the projector farther away from the screen.
Adjusting the Image Shape You can maintain a square or rectangular image by placing the projector directly in front of the screen and keeping it level. This also produces the best picture quality. If the projector is tilted up or placed at an angle, you’ll need to correct the image shape by using one of the functions described below. Using Quick Corner Use Quick Corner to adjust the shape and size of the image when it’s uneven on all sides. Follow these steps to select Quick Corner: 1.
Using Keystone Correction You can manually adjust the shape of the image to compensate for vertical and horizontal keystone distortion. First make sure the Keystone setting in the projector’s menu system is set to H-Keystone or V-Keystone: 1. Press the Menu button on the remote control or projector. 2. Select the Settings menu and press Enter. 3. From the Settings menu, select Keystone and press Enter. 4. Select H/V-Keystone and press Enter.
Selecting the Color Mode The Color Mode adjusts the brightness, contrast, and color for various common viewing environments. Use this setting to quickly obtain a good picture. Press the Color Mode button on the remote control, and then select from one of these options: ■ Presentation: For making color presentations in a bright room. ■ Text: For making black-and-white presentations in a bright room. ■ Theatre: For watching movies in a darkened room; gives images a natural tone.
Resizing Video Images You can use the Aspect button on the remote control to change the aspect (width to height) ratio, depending on the input signal. ■ Auto (HDMI images only): Automatically sets the aspect ratio according to the input signal. Choose this setting to project an HDMI image in the best aspect ratio. ■ Normal (for images sent through the Computer1, Computer2, or BNC ports only): Displays images using the full projection area and maintains the aspect ratio of the image.
3 3 Presenting With the Remote Control The projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 49 feet (15 meters) away. You can use the remote control to adjust the picture and sound (page 52), as a pointer to highlight your presentation (page 55), or to control two or more projectors at the same time (page 57).
note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve battery power. When you release the button, normal operation resumes. Using the Remote Control Make sure batteries are installed as described on page 130. Follow these tips for using the remote control: ■ Point the remote control at the front of the projector or at the screen. ■ Stand within 49 feet (15 meters) of the projector.
Turning Off the Picture and Sound You can temporarily turn off the image and sound by pressing the A/V Mute button on the remote control. This turns the image black and stops the sound. To turn the image and sound back on, press the button again. You can have the screen turn blue (using the Display setting as described on page 107) or display an image such as a company logo when you press the A/V Mute button. (See page 104 for more information on displaying an image.
Zooming Part of Your Image You can zoom in on a portion of the image using the E-Zoom buttons on the remote control. 1. Press the E-Zoom button on the remote control. You see a crosshair indicating the center of the zoom-in area. 2. Use the pointer button to position the crosshair. button to enlarge the selected 3. Continue pressing the E-Zoom area up to 4 times. 4.
Highlighting Your Presentation You can display a pointer to call out important information on the screen, and you can choose from three shapes for the pointer. Using the Pointer Tool 1. To activate the pointer tool, press the Pointer button on the remote control. A pointer appears on the screen. Pointer If you prefer to use a different style of pointer, see the instructions in the next section. 2. Use the pointer button on the remote control to position the pointer on the screen. 3.
Operating Your Computer With the Remote Control With the optional wireless mouse receiver (see page 12), you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering slideshow-style presentations, since you won’t have to stand next to the computer to change slides. ■ Use the Up and Down buttons to move through a ® Microsoft PowerPoint slideshow.
Operating Two or More Projectors With the Remote Control If you’re using more than one projector, you can control all the projectors—or just selected ones—by using the projector ID system. To operate a projector, set the remote control’s ID to match that of the projector. Or you can control all the projectors at once by setting the remote control’s ID to zero. Setting the Projector ID The projector’s default ID is set to Off. This lets it respond to commands from any remote control.
Checking the Projector ID You can check the projector’s ID by following these steps: 1. Point the remote control at the projector you want to check. 2. While holding the ID button, press the Help button. You see a message on the screen like this: Setting the Remote Control ID note If you’re using a remote control ID other than the default ID of zero, you have to set the ID each time you turn on the projector. The remote control’s default ID is zero. This lets you operate any projector.
4 4l Preparing the Projector to Present Through a Network This chapter tells you how to prepare your projector so that you can send pictures to it through a network (G5150NL and G5350NL only). Using EMP NS Connection, you can project images shown on your computer screen—including text, graphics, and video—directly to your audience. If you have Windows Vista, you can also use the Network Projector feature to communicate with your network-connected projector without installing any software.
Configuring Basic Settings You can give your projector a unique name, enable a projector keyword, or create a password for controlling the projector using your computer’s Web browser. 1. Press the Menu button, then choose Network and press Enter. 2. Choose Network Configuration and press Enter. You see the following screen: 3. Choose Basic and press Enter. 4. Make sure the projector has a unique name, so you can identify it when connecting to it from your computer.
5. Press the pointer button to select individual letters; then press Enter to input a character. To add a blank space or to navigate backward and forward through the input text, highlight the arrows and press Enter. To toggle symbol settings or capital letters, highlight the option and press Enter. When you’re done, highlight Finish and press Enter. 6.
Configuring a Wireless Connection If you have installed the optional wireless LAN module (G5150NL and G5350NL only), you can use NS Connection to connect to the projector and send images wirelessly in two modes: Ad Hoc mode or Access Point mode. note ■ Ad Hoc mode (computer-to-computer mode) lets you connect just one computer to the projector at a time; it’s easy to set up, and the only equipment you need is a computer with a wireless (802.11g, 802.11b, or 802.
You see this screen: 4. Make sure Quick is selected for the Connection mode. If not, use the pointer button on the remote control to highlight Quick, then press Enter to select it. 5. If your network is using 802.11a, use the pointer button on the remote control to highlight 802.11a, then press Enter to select it. 6. If your computer’s network card supports an SSID (or ESSID) name (see page 67), highlight the SSID text box, press Enter, and enter a name.
Note that the SSID is case-sensitive (if you enter the name in uppercase on the projector, you must type it the same way on the computer connecting to the projector). 7. If you want to prevent the SSID from being displayed on the standby screen, set the SSID Display option to Off. 8. To prevent the IP address from appearing on the standby screen, set the IP Address Display setting to Off. 9.
Configuring the Network Settings for Windows Before connecting to the projector, you need to make sure the settings for your notebook’s or PC’s network card match the settings you entered for the projector. 1. Access your wireless network Properties window. For example, in Windows XP you would click Start > Control Panel > Network and Internet Connections. Then click the Network Connections icon.
2. Right-click the Wireless Network Connection icon and select Properties. You see a screen similar to this: Click here 3. Click the Configure button. 4. Click the Advanced tab.
5. Check your wireless card or adapter device settings. (Depending on the type of card or adapter you’re using, some of the settings may be different than those listed here.) ■ Set the Network Type to 802.11 Ad Hoc. ■ Set the SSID to match the name you assigned to the projector’s SSID. ■ Make sure Encryption is Disabled. 6. Click the General tab and make sure that your wireless card or adapter is enabled. 7. When you’re done, click OK to close the Properties dialog box.
3. Make sure Location is set to Automatic. Select Automatic note If you don’t need the other network port configurations, disable them by deselecting their checkboxes. When you connect in Ad Hoc mode, your connection to other wireless networks or devices is broken. If you need to remain connected to your wireless network, use Access Point mode, as described on page 69. Also, make sure you reconnect to your original wireless network when you are done using the projector.
Using Access Point Mode To use Access Point (infrastructure) mode, first adjust your projector and wireless access point or AirPort base station settings as described in this section. Configuring the Projector 1. Press the Menu button, then choose Network and press Enter. 2. Choose Network Configuration and press Enter. 3. Choose Wireless LAN and press Enter. You see this screen: 4. Make sure Advanced is selected for the Connection mode.
Highlight the SSID text box, press Enter, and enter a name as follows: Press the pointer button to select individual letters; then press Enter to input a character. To add a blank space or to navigate backward and forward through the input text, highlight the arrows and press Enter. To toggle symbol settings or capital letters, highlight the option and press Enter. When you’re done, highlight Finish and press Enter.
10. When you’re done making these settings, select Return, Setup complete, and then Yes to confirm that you want to save the changes. 11. Press Menu to exit. Now you’re ready to set up your computer for wireless projecting. Go to “Configuring the Network Settings for Windows” below, or go to “Setting Up Your Mac for Access Point Mode” on page 77. If you want to enable security options for your network, see page 85 to set up the option that your network uses on the projector.
You see a screen similar to this: Click here 3. Click the Configure button. 4. Click the Advanced tab.
5. Check your wireless card’s or adapter’s device settings. (Depending on the type of card or adapter you’re using, some of the settings may be different than those listed here.) ■ Set the Network Type to Infrastructure. ■ Set the SSID to match the name assigned to the access point (which should also match the projector’s SSID). ■ Make sure Encryption is Disabled if you have not set up encryption on the projector. 6. Click the General tab and make sure that your wireless card or adapter is enabled. 7.
9. Select Internet Protocol and click the Properties button. You see this screen: note For specific details about your network, please consult your network administrator. 10. If your access point uses DHCP, select Obtain an IP address automatically. Otherwise select Use the following IP address and Use the following DNS server addresses, then enter the required information: ■ IP address: Type in the IP address you want to assign to the computer. It must be formatted like other addresses on the network.
12. Click the Wireless Networks tab. (If you don’t see this tab, you may need to enable your wireless card or adapter by clicking Configure to access the device settings; then follow any instructions on the screen to enable the device.) You see a screen like this: 13. Verify that you’ve enabled your computer’s connection to the access point. It should be listed with the small icon next to it, indicating a connection. If it’s not listed, click Configure and type the name of your access point. 14.
Checking the Gateway IP Address on Windows note If you cannot identify the gateway address using this Windows utility, use the administrator’s utility software that came with your access point. If you’re entering IP addresses manually and need to find out the gateway IP address (the IP address of your access point), make sure the wireless connection to the access point is currently active, as described in the previous section. Then follow these steps: 1. Access your wireless network Properties window.
3. Click the Support tab. The gateway’s IP address is listed as shown: Gateway address Setting Up Your Mac for Access Point Mode Your AirPort software is automatically configured to allow your Mac to detect Access Point networks. Typically, you only need to select your AirPort network name from the AirPort status menu on the Mac menu bar. If you’re having problems connecting to the projector, follow these steps: 1. From the Apple pull-down menu, select System Preferences. 2. Click the Network icon.
3. Make sure Location is set to Automatic. note If you don’t need the other network ports, disable them by deselecting their checkboxes. If more than one network port is enabled, the projector software warns you to turn off AirPort when you first connect the projector. Disregard this message. Your AirPort network and base station names may be different. To check or change your AirPort network name, start the AirPort Admin utility, select your base station, and click Configure.
10. Click the AirPort icon on the menu bar at the top of the Macintosh desktop. You see the AirPort status menu: 11. Check to make sure AirPort is turned on. 12. Select the name of your AirPort network.
Follow these steps to open the WPS connection screen: 1. Press the Menu button to open the projector menu. 2. Select Network, then Network Configuration, and press Enter. The Network Configuration screen is displayed. 3. Select Wireless LAN and press Enter.
4. Select To Setup Wizard, then press Enter. You see the WPS (Wi-Fi Protected Setup) connection screen: 5. For the Push Button Method, follow the instructions below. For the PIN Code Method, follow the instructions on page 83. Using the Push Button Method 1. Select Push Button Method and press Enter. You see this screen: 2. Press the Enter button on the projector.
3. When prompted by the screen, press the WPS button on the access point. You see a message that WPS setup is complete. 4. Press the Enter button or the Esc button to return to the wireless LAN setting page. 5. Select Setup Complete and press Enter. 6. Make sure Yes is selected and press Enter. 7. Press the Menu button.
Using the PIN Code Method Before you can make a connection using the PIN Code Method, a connection must have already been established between the computer and the access point. For details on how to make this connection, refer to the manual provided with the access point. 1. Follow steps 1 through 4 on page 80 to access the WPS Connection Screen. 2. Select PIN Code Method and press Enter. You see this screen: 3.
4. When you see a message that WPS Setup is complete, press the Enter or Esc button. 5. When you see the wireless LAN setting page, select Setup Complete and press Enter. You see this screen: 6. Select Yes and press Enter to save the settings. 7. Press the Menu button and then close the configuration menu to exit.
Using Wireless Security Options If you have installed the optional wireless LAN module (G5150NL and G5350NL only), you can use the following security options when connecting to the projector wirelessly: WEP encryption, WPA security, EAP-TLS certificate validation, or LEAP, EAP, or PEAP authentication. To set these security features on your wireless network, see your documentation or get help from your network administrator.
5. For the WEP encryption setting, highlight 128Bit or 64Bit and press Enter. 6. For Format, highlight ASCII to enable text input or HEX to enable hexadecimal input. Then press Enter. note Text input for WEP encryption varies with different access points; check with your network administrator. Try ASCII first. If that doesn’t work, try Text2 and then Text3. 7. If you chose 64Bit, choose Key ID 1, 2, 3, or 4.
Enabling WPA Security 1. Press Menu. Highlight Network and then press Enter. 2. Choose Network Configuration and press Enter. 3. Highlight Security and press Enter. Then press Enter again to display the security options: 4. Choose WPA-PSK(TKIP), WPA-PSK(AES), WPA2-PSK(TKIP), or WPA2-PSK(AES) and press Enter. Highlight the PSK (pre-shared key) text box and press Enter. Press the pointer button to select individual letters; then press Enter to input a character.
Enabling EAP, LEAP, or PEAP Authentication 1. Press Menu. Highlight Network and then press Enter. 2. Choose Network Configuration and press Enter. 3. Highlight Security and press Enter. Then press Enter again to display the security options: 4. Choose EAP-TTLS/MD5, EAP-TTLS/MS-CHAPv2, PEAP/MS-CHAPv2, PEAP/GTC, LEAP, EAP-Fast/MS-CHAPv2, or EAP-FAST/GTC. Then press Enter. 5. Enter the user name and password that match the settings on your authentication server.
Highlight the Password text box and press Enter. Enter the password as you entered the User name. 6. When you’re done making these settings, select Return, Setup complete, and then Yes to confirm that you want to save the changes. 7. Press Menu to exit. Enabling EAP-TLS Certificate Validation Once you have created an EAP-TLS certificate, follow the steps below to enable it. (Contact your Network Administrator for more information on obtaining or creating the certificate.) 1. Press Menu.
Projecting Over a Network Once you’ve set up your projector and computer in either Ad Hoc (Quick) mode or Access Point (Advanced) mode (or in the optional wired LAN mode, as described on page 114), see the EasyMP Operation Guide for instructions on the following EasyMP features (G5150NL and G5350NL only): ■ Starting NS Connection ■ Projecting over the network ■ Multi-screen projection ■ Projecting video clips (Movie Sending Mode) ■ Using Presentation Mode ■ Using Virtual Displays Connecting With
3. From the Start menu on your computer, select All Programs, Accessories, then Connect to a Network Projector. You see this screen: 4. You can select the projector automatically or manually: ■ To let your computer search automatically for the projector, select Search for a projector. You see this screen: After locating the connected projectors, your computer lists them on the screen. Select the one you want and then click Connect.
■ To locate the projector by IP address, select Enter the projector address. You see this screen: Enter the IP address for the projector in the format shown. Enter a password for the projector if one has been set. Then click Connect. 5. If you need to pause your presentation, press the Pause button. Click Resume when you are ready to continue. 6. When you want to disconnect from the projector, click the Disconnect button.
5 5 Fine-Tuning the Projector You can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options Menu list The menus are listed on the left and the options available for the highlighted menu are shown on the right. note For a complete list of menus and options, see page 110.
4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the Enter button to view a sub-screen for changing the setting. ■ Press the left or right side of the a slider bar. pointer button to adjust ■ To select from two or more settings, use the pointer button to highlight the desired setting and press Enter. 5.
Adjusting the Image You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast. 1. Press the Menu button on the projector or remote control and select the Image menu. You see a screen similar to one of those below. (The settings will be different depending on the source you are projecting from.) Computer/RGB Video note The available settings vary depending on the input source selected. Component Video/ Composite Video/ S-Video 2.
■ Sharpness Adjusts the sharpness of the image. ■ Abs. Color Temp. Sets a color temperature between 5000 and 10000 °K. (Not available if sRGB is selected as the Color Mode setting.) ■ Color Adjustment Adjusts the color values. For Customized color mode, select R, G, B, C, M, Y to adjust individual red, green, blue, cyan, magenta, and yellow hue and saturation values. For other color modes, RGB may be selected to adjust red, green, and blue hue and saturation values.
You may need to readjust the color as the lamp in your projector changes over time. Adjusting Signal Settings Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments. In addition to changing the position of the projected image, you can correct tracking and sync for computer images, or change the aspect ratio to widescreen format for video images. 1. Press the Menu button and select the Signal menu.
■ Tracking note Adjust this value to eliminate vertical stripes in computer images. ■ Sync Adjust this value if computer images appear blurry or flicker. ■ Position You can also use the remote control’s Auto button to automatically reset the projector’s Tracking, Sync, and Position settings. See page 141 for details. If the image is slightly cut off on one or more sides, it may not be centered exactly. Select this setting and use the pointer button to center it.
■ Video Signal Select the setting for the type of equipment you’ve connected to the Video1 or Video2 ports. Leave this setting at Auto unless you are using a 60-Hz PAL system (then select PAL60). ■ Aspect Sets the image’s aspect ratio (ratio of width to height). Depending on your projector model and input source, you can select Auto, Normal, 4:3, 16:9, Full, Zoom, or Through; see page 50 for more information.
■ Control Panel Lock Lets you disable all of the buttons on the projector, or all of the buttons except the Ppower button. See page 106 for more information. ■ Pointer Shape Lets you choose from three pointer shapes. See page 55 for more information. ■ Brightness Control Lets you select from two levels of brightness. The Low setting reduces power consumption and noise, and extends the lamp’s operating life. ■ note Volume You can also adjust the volume using the remote control.
Using the Projector Security Features note You can also attach a security cable to the projector to prevent theft (see page 150). caution If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times. Also, it’s a good idea to write down your password. To prevent unauthorized use of the projector, you can do the following: ■ Assign a password.
4. Hold down the Num button on the remote control and use the numeric keypad to enter a four digit password. (The default setting is 0000.) 5. When you see a confirmation message, reenter the password. Then press the Menu button to exit the screen. To set security options, access the Password Protect screen as described on page 102, and then turn on any of the following options: ■ Power On Protect to prevent unauthorized use of the projector.
If the password is not correct, you see a message prompting you to re-enter the password. If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked and the projector switches to standby mode. Disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on. When you see the Password screen again, you can try to enter the correct password.
Capturing the Image Start by displaying the image you want to use from either a computer or video source, such as a DVD player or digital camera. Then follow these steps to capture the image and transfer it to the projector: 1. Press the Menu button on the remote control, highlight the Extended menu, and press Enter. 2. Highlight User’s Logo and press Enter. note When you choose an image for the user’s logo, it erases any previously used image. You can save an image up to 300 × 400 pixels in size.
Choosing When to Display the Image After your image is saved, you can set it to display as the startup screen, the screen you see when there’s no signal, or the screen you see when you press the A/V Mute button (see page 53). 1. Press the Menu button, highlight the Extended menu, and press Enter. 2. Select Display and press Enter. 3. Choose from these display options: note You can lock these settings to prevent them from being changed without a password (see page 102).
Customizing Power and Operation You can use the Extended menu to customize the way the projector displays images, enable quick startup, turn sleep mode on or off, and customize other projector operations. ■ Display Use this setting to turn off the display of messages, change the background color, enable logo display, or turn off the startup screen display. ■ Closed Caption Enables or disables closed captions. Select CC1, CC2, or OFF.
Ppower button). Enable Sleep Mode if you want the projector to turn off automatically if it is idle (and no signal is received) for 10 minutes (you can adjust the amount of time using the Sleep Mode Timer setting). Enable High Altitude Mode when you are using the projector above 4,900 feet (1,500 meters). Enable BNC Sync Termination when analog (75Ω) termination (such as for switchers) is necessary.
Multi-screen Color Adjustment You can match the color of projected images when two or more projectors are being used to display images near each other, or when you use the multi-screen feature to project from one source (one image) as described in the EasyMP Operation Guide. For each screen, you can set five levels of brightness and color correction. 1. Before starting, you may want to assign a numeric ID to each projector. This lets you use the remote control to select the projector you want to adjust.
Projector Menu and Options List The table below shows the options you can select based on the projector menu you are viewing. Some options may not be available depending on the projector model and input source you are using. For more information on these menus and options, read this chapter. 110 Menu Options Image Color Mode Brightness Contrast Color Saturation Tint Sharpness Abs. Color Temp. Color Adjustment Reset Signal Auto Setup Resolution Tracking Sync.
Menu Options Extended Display Closed Caption User’s Logo Projection Operation Standby Mode Projector ID Multi-screen Language Reset Network Basic Wireless LAN (G5150NL and G5350NL only) Security Wired LAN PJLink Password Web Control Password SNMP Mail AMX Device Discovery Projector Name Others Reset Info Lamp Hours Source Input Signal Resolution Video Signal Refresh Rate Sync Info Status Reset Reset All Reset Lamp Hours Fine-Tuning the Projector 111
Fine-Tuning the Projector
6 6 Managing Projectors The software included with your projector lets you monitor and control your projectors from a remote computer. First connect and configure each projector you want to monitor. You can connect the projector wirelessly in Access Point mode (G5150NL and G5350NL only, as described on page 69) or over a wired network as described in this chapter.
Connecting to a Wired Network Follow these steps to connect the projector to your network and configure it with an IP address: PowerLite Pro G5150NL and G5350NL 1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the LAN port on the projector. See page 37. 2. Turn on the projector. 3. Press the Menu button on the remote control, select the Network menu, then press Enter. 4. Choose Network Configuration and press Enter. 5.
6. Do one of the following: ■ If your network assigns addresses automatically, turn on the DHCP setting. ■ If your network does not assign addresses automatically, turn off DHCP and enter the projector’s IP Address, Subnet Mask, and Gateway Address. note If you’re a network administrator, you can use the SNMP option to enter a trap IP address. This lets you receive trap alerts for the projectors you’re monitoring.
5. Do one of the following: note If you’re a network administrator, you can use the SNMP option to enter a trap IP address. This lets you receive trap alerts for the projectors you’re monitoring. ■ If your network assigns addresses automatically, turn on the DHCP setting. ■ If your network does not assign addresses automatically, turn off DHCP and enter the projector’s IP Address, Subnet Mask, and Gateway Address.
3. Choose Mail, then press Enter. You see a screen like this: 4. Highlight On to receive e-mail notifications, then press Enter. 5. Enter the IP address for the SMTP server for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used: 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255). 6. Enter the SMTP server’s port number. The default value is 25. You can enter a numeric value from 1 to 65535. 7.
When the selected problem or warning occurs, an e-mail message is sent to the specified notification addresses. The subject line of the e-mail is EPSON Projector. The e-mail includes the following information: ■ Line 1: The name of the projector where the problem has occurred ■ Line 2: The IP address of the projector where the problem has occurred ■ Line 3: Details of the problem PowerLite Pro G5200WNL 1. Press the Menu button on the remote control, select the Network menu, then press Enter.
6. Choose one of the Email Address fields, then enter the e-mail address where you want to receive a message when a problem occurs. You can register up to three addresses. You can enter up to 32 alphanumeric characters for the e-mail address. 7. Select problems or warnings to be notified about by e-mail. (Numbers 1 through 3 in this section correspond to the e-mail addresses you entered.) 8.
Managing Projectors
7 7 Maintaining the Projector Y our projector needs little maintenance. All you have to do is keep the lens clean. You may also need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens caution Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged. Clean the lens whenever you notice dirt or dust on the surface. To remove dirt or smears on the lens, use a commercially available cloth for cleaning glasses. Cleaning the Projector Case caution Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case. Before you clean the case, turn off the projector and unplug the power cord.
Follow these steps: 1. Turn off the projector and unplug the power cord. 2. Grip the air filter cover tab and remove the air filter cover as shown. 3. Place your finger into the groove and remove the air filter as shown. 4. With the front of the air filter facing down, tap it four or five times to shake off the dust. Turn it over and tap the other side in the same way to shake off the dust.
5. To clean any dust remaining on the air filter, use a small vacuum cleaner designed for computer and other office equipment to clean the front. If you don’t have one, gently clean the vent with a soft brush (such as an artist’s paintbrush). 6. Insert the air filter back into the holes in the cover, then press it firmly into place. 7. Slide the air filter cover in until you feel resistance. 8. If the dirt is difficult to remove or the filter is broken, replace the filter as described on page 125.
Replacing the Air Filter Follow these steps to replace the air filter: 1. Grip the air filter cover tab and remove the air filter cover as shown. 2. Place your finger into the groove and remove the air filter as shown.
3. Insert the new air filter into the holes in the cover, then press it firmly into place. 4. Slide the air filter cover in until you feel resistance. Replacing the Lamp note Turn off this product when not in use to prolong the life of the projector. The life span of the projection lamp is about 2000 hours if Brightness Control in the Settings menu is set to High (default), and 3000 hours if Brightness Control is set to Low. See page 130 to check the lamp usage.
You may also need to replace the lamp if the red. See page 135. Lamp light flashes Lamp light warning Let the lamp cool fully before replacing it. Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766). Request part number V13H010L47 (G5150NL) or V13H010L46 (G5350NL and G5200WNL). Follow these steps to replace the lamp: 1. Turn off the projector and, after the projector beeps twice, unplug the power cord. 2. Let the projector cool for at least an hour (if it has been on).
4. Loosen the two screws holding the lamp in place (you can’t remove them). Loosen, but don’t remove these screws note The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 5. Hold the lamp as shown and pull it straight out. 6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.) 7. Once the lamp is fully inserted, tighten its screws.
8. Replace the lamp cover, then tighten its screws. 9. Reset the lamp timer as described in the next section. Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menu. 1. Press the Menu button on the remote control or on the projector’s control panel. You see the main menu. 2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight Reset, then press Enter. You see this screen: 3.
Checking Lamp Usage To check the number of hours the lamp has been used, press the Menu button and highlight the Info menu. You see a screen like this: note The information displayed depends on the input signal currently selected. caution When replacing batteries, take the following precautions: ■ Replace the batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash immediately. ■ Do not expose batteries to heat or flame.
3. Install two AA alkaline batteries, inserting the + and – ends as shown. 4. Position the cover as shown, then press down until it snaps into place. Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent damage: note ■ When shipping the projector for repairs, use the original packaging material if possible, including the protective lens pads.
Maintaining the Projector
8 8 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on the back of the projector or on the remote control. 1. Press the ? Help button on the remote control or on the projector. You see the Help menu: 2. Use the pointer button on the remote control or the navigational buttons on the projector to highlight menu items. 3. Press the Enter button on the remote control or on the projector to select the menu item. 4.
Checking Projector Status If your projector isn’t working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status.
Status lights (continued) Light Status Description Flashing orange It’s time to replace the lamp. See page 126 for instructions. If you continue to use the lamp after the replacement warning, there is an increased possibility that the lamp may break. Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher.
Solving Projector Operation Problems The power doesn’t turn on. ■ If the projector doesn’t turn on when you press the Ppower button, make sure the power cord is connected to the projector and plugged into a working electrical outlet. ■ The power cord may be defective. Disconnect the cord from the outlet and contact Epson as described on page 146. ■ If you’re using the Direct Power On function and you immediately plug the power cord back in after unplugging it, the power may not turn back on.
■ The attached computer may be in sleep mode or displaying a black screen saver. Try pressing a key on the computer. ■ If you are projecting from a DVD player or other video source, make sure you turn it on and press its Play button. ■ If you are projecting from a video source, make sure the Video Signal setting is correct (see page 98). ■ You can also try resetting all of the configuration menu settings. See page 95.
■ Depending on your computer’s video card, you might need to use the Display utility in the Control Panel to make sure that both the LCD screen and external monitor port are enabled. See your computer’s documentation or online help for details. If you’re using Mac OS X: 1. Open System Preferences. 2. Click Displays. 3. Click Detect Displays. 4. Make sure the VGA Display or Color LCD dialog box is selected. 5. Click the Arrangement or Arrange tab. 6. Make sure the Mirror Displays checkbox is selected.
■ You also may need to modify existing presentation files if you created them for a different resolution. See your software documentation for specific information. ■ If you’re projecting a wide panel computer image, adjust the Resolution setting (see page 98). ■ If you’re projecting an image from a computer with dual display activated, turn dual display off. The image isn’t square, but keystone-shaped. If the image isn’t square or rectangular, adjust its shape as described on page 47.
■ If the projector is angled sharply toward the screen, it may not be possible to focus the entire image. Move the projector to position it more directly in front of the screen. ■ Lower the projection angle to reduce the amount of keystone correction required. ■ Make sure the projector is within the proper range (projection distance) from the screen (see page 156). ■ Make sure the lens is not fogged by condensation.
3. Adjust the Sync setting to increase the image sharpness. The image is too light or dark, or colors are incorrect. note Because of the different technologies used, your projected image may not exactly match the colors on your notebook or computer monitor. ■ Use the Color Mode option in the projector’s Image menu to adjust the color (see page 96). ■ If you’re displaying video, adjust the Color Adjustment and Color Mode settings on the Image menu.
■ If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted. In Windows, you may be able to check this by clicking the volume control in your Windows system tray (lower right corner of the screen). On a Mac, you may be able to adjust the volume from your menu bar (top right corner of the screen) or via the volume control function keys.
■ Make sure the projector is plugged in. ■ Make sure the LAN cable is connected correctly. Reconnect it if it is not connected or it is not connected correctly (see page 37). For problems with EasyMP or the EMP NS Connection software, see the EasyMP Operation Guide. For problems with EMP Monitor, see the EMP Monitor Operation Guide.
Solving Problems With the Remote Control The projector doesn’t respond to remote control commands. ■ Point the remote control towards the receiver. ■ Make sure the projector and remote control IDs match. To operate all projectors by remote control regardless of ID settings, set the ID switch on the side of the remote control to Off. ■ The remote control’s batteries may not be installed correctly or may be low on power. To change the batteries, see page 130.
Where To Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website for solutions to common problems with the PowerLite Pro G5150NL, PowerLite Pro G5350NL, or PowerLite Pro 5200WNL. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Visit Presenters Online to access tips, templates, and training for developing successful presentations.
Before you call for support, please have the following information ready: ■ Product name (PowerLite Pro G5150NL, PowerLite Pro G5350NL, or PowerLite Pro G5200WNL) ■ Product serial number (located on the projector) ■ Proof of purchase (such as a store receipt) and date of purchase ■ Computer or video configuration ■ Description of the problem Purchase Supplies and Accessories You can purchase screens and other accessories from an Epson authorized reseller.
Solving Problems
A A Projector Installation This appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt the projector down to position the image on the screen. This causes the image to lose its square shape. You can correct the image using the projector’s Quick Corner and/or Keystone functions, as described on page 47. Security Features The projector includes security features to prevent its theft when installed or used in public locations: ■ Security cable attachment.
■ Lens theft deterrent screw. You can lock the lens with the supplied screw, so that the lens cannot be removed. In addition, the projector includes several menu-operated security features. See page 102. Installing the Cable Cover Install the rear cable cover to enhance the appearance of the projector and prevent any cables from being loosened or removed.
To remove the cover (when connecting or disconnecting cables), loosen the screws on the bottom of the cover, pull the bottom of the cover away from the projector as shown. Installing and Removing the Lens note Only install or remove the lens when necessary. If dust enters the projector, projection quality may deteriorate and/or the projector may malfunction. Do not install or remove the lens when the projector’s lens insertion section is facing up. Dust could enter the projector.
3. Make sure the white dot on the lens is facing up. Insert the lens straight into the projector, then turn clockwise until you hear it click into place. white dot 4. If necessary, attach the lens theft deterrent screw (see page 151). Removing the Lens 1. Turn off the projector and unplug the power cord. 2. If you’ve attached the lens theft deterrent screw, remove it (see page 151). 3. Hold down the lens removal button and turn the lens counterclockwise until you hear it click. 4.
Projector Installation
B B Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) PowerLite Pro G5150NL: 1024 × 768 pixels (XGA) PowerLite Pro G5350NL: 1024 × 768 pixels (XGA) PowerLite Pro G5200WNL 1280 × 800 pixels (WXGA) Color reproduction 16.
Image size PowerLite Pro G5150NL (4:3 image): 30 to 300 inches (76.2 to 762 centimeters) PowerLite Pro G5350NL (4:3 image): 30 to 300 inches (76.2 to 762 centimeters) PowerLite Pro G5200WNL (16:10 image): 30 to 300 inches (76.2 to 762 centimeters) Projection distance PowerLite Pro G5150NL (4:3 image): 2.7 to 47.8 feet (0.8 to 14.6 meters) PowerLite Pro G5350NL (4:3 image): 2.7 to 47.8 feet (0.8 to 14.6 meters) PowerLite Pro G5200WNL (16:10 image): 2.7 to 50.3 feet (0.8 to 15.
Keystone correction ±40° vertical, ±20° horizontal (standard lens) Mouse compatibility Requires optional Wireless IR Mouse Receiver (part number V12H007T16) note Projection Lamp Type UHE (Ultra High Efficiency) Power consumption PowerLite Pro G5150NL 210 W PowerLite Pro G5350NL 275 W PowerLite Pro G5200WNL 275 W Lamp life Approx. 2000 hours (High Brightness mode) Approx.
Weight (without lens) PowerLite Pro G5150NL 14.8 lb (6.7 kg) PowerLite Pro G5200WNL 14.8 lb (6.7 kg) PowerLite Pro G5350NL 15 lb (6.8 kg) Electrical 158 Technical Specifications Rated frequency 50/60 Hz AC Power supply 100/240 VAC, 3.8A/1.7 A Power consumption PowerLite Pro G5150NL Operating: 100 to 120 VAC, 343 W 220 to 240 VAC, 327 W Standby: 100 to 120 VAC, 0.4 W (network off) 10 W (network on) 220 to 240 VAC, 0.
Environmental Temperature Operating: 32 to 104 °F (0 to 40 °C) 32 to 95 °F (0 to 35 °C) (over 1,500 m/4,921 ft, with High Altitude Mode and High Brightness mode active) Storage: 14 to 140 °F (–10 to 60 °C) Humidity (non-condensing) Operating: 20 to 80% RH Operating altitude 0 to 9,843 ft (0 to 3,000 m) Safety and Approvals United States FCC 47CFR Part 15B Class B (DoC) UL60950-1 First Edition (cTUVus Mark) Canada ICES-003 Class B CSA C22.2 No.
PowerLite Pro G5150NL/G5350NL Compatible video formats Mode 160 Technical Specifications Refresh Rate (Hz) Resolution VGA EGA* 70 640 × 350 VGA—60 VESA—72* VESA—75* VESA—85* 60 72 75 85 640 × 480 640 × 480 640 × 480 640 × 480 SVGA—56* SVGA—60 SVGA—72* SVGA—75* SVGA—85* 56 60 72 75 85 800 × 600 800 × 600 800 × 600 800 × 600 800 × 600 XGA—60* XGA—70* XGA—75* XGA—85* 60 70 75 85 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA1—70* SXGA1—75* SXGA1—85* 70 75 85 1152 × 864 1152 × 864 1152 × 86
Compatible video formats (continued) Mode Refresh Rate (Hz) Resolution iMAC VGA* iMAC SVGA* iMAC XGA* MAC13* MAC16* MAC19* MAC19-60* MAC21* 117 95 75 67 75 75 59 75 640 × 480 800 × 600 1024 × 768 640 × 480 832 × 624 1024 × 768 1024 × 768 1152 × 870 NTSC NTSC 4:43 PAL N-PAL M-PAL PAL—60 SECAM 60 60 50 50 60 60 50 — — — — — — — TV525i (480i) TV625i (576i) SDTV525p (480p) SDTV625p (576p) HDTV750p (720p) HDTV750p (720p) HDTV1125i (1080i) HDTV1125i (1080i) HDTV1125p (1080p) HDTV1125p (1080p) HDTV1125p (
PowerLite Pro G5200WNL Compatible video formats Mode 162 Technical Specifications Refresh Rate (Hz) Resolution VGA EGA* 70 640 × 350 VGA—60 VESA—72* VESA—75* VESA—85* 60 72 75 85 640 × 480 640 × 480 640 × 480 640 × 480 SVGA—56* SVGA—60 SVGA—72* SVGA—75* SVGA—85* 56 60 72 75 85 800 × 600 800 × 600 800 × 600 800 × 600 800 × 600 XGA—60* XGA—70* XGA—75* XGA—85* 60 70 75 85 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA1—70* SXGA1—75* SXGA1—85* 70 75 85 1152 × 864 1152 × 864 1152 × 864 WXGA
Compatible video formats (continued) Mode Refresh Rate (Hz) Resolution iMAC VGA* iMAC SVGA* iMAC XGA* MAC13* MAC16* MAC19* MAC19-60* MAC21* 117 95 75 67 75 75 59 75 640 × 480 800 × 600 1024 × 768 640 × 480 832 × 624 1024 × 768 1024 × 768 1152 × 870 NTSC NTSC 4:43 PAL N-PAL M-PAL PAL—60 SECAM 60 60 50 50 60 60 50 — — — — — — — TV525i (480i) TV625i (576i) SDTV525p (480p) SDTV625p (576p) HDTV750p (720p) HDTV750p (720p) HDTV1125i (1080i) HDTV1125i (1080i) HDTV1125p (1080p) HDTV1125p (1080p) HDTV1125p (
Technical Specifications
C C Notices T his appendix includes safety instructions and other important information about your projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not look into the lens when the projector is on. The bright light can damage your eyes. ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not operate the projector on its side, or while tilted to one side.
Notices ■ Never push objects of any kind through the cabinet slots. ■ Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle. ■ Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it on top of loose papers, which could block vents underneath your projector.
■ Use the type of power source indicated on the projector. Use of a different power source may result in fire or electric shock. If you are not sure of the power available, consult your dealer or power company. ■ If you use the projector in a country other than where you purchased it, use the correct power cord for that country. ■ Do not overload wall outlets, extension cords, or power strips. Do not insert the plug into a dusty outlet. This can cause fire or electric shock.
WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. (Provided in accordance with Proposition 65 in Cal. Health & Safety Code §25249.5 et seq.) FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
For Canadian Users This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.
Notices
Index A C A/V Mute button, 53 display settings, 106 Access Point mode, 69 to 79 Access point, checking IP address of, 76 to 77 Accessories, 12 to 13 Ad Hoc mode, 62 to 68 Air filter cleaning, 122 to 124 ordering, 12 replacing, 125 to 126 AirPort, configuring for wireless, 67 to 68, 77 to 79 Altitude, 108, 136, 159 Anti-theft device, 13, 19, 150 to 151 Aspect ratio, 156 Audio connecting equipment, 32 to 34 controlling volume, 54 problems, troubleshooting, 142 to 143 turning off (using A/V Mute), 53 Authent
Connecting projector to audio equipment, 32 to 34 to computer, 19 to 23 to digital camera, 35 to 36 to external monitor, 31 to speakers, 34 to video equipment, 24 to 30 Contrast setting, 96 Control Panel Lock setting, 101, 106 Custom screen, see User’s Logo Customized color mode, 49 D Default settings, restoring, 95 DHCP, 70, 74, 78 Digital camera connecting to, 35 to 36 Direct Power On, 39 Distance from projector to screen, 17, 156 Documentation, 10 to 11 DVD player, connecting, 24 to 30 E EAP authentica
Info menu, 130 Infrastructure mode, see Access Point mode Input Signal setting, 99 Input signal, selecting, 42, 52 Installing cable cover, 151 to 152 projector, 149 to 150 Instant Off, 40 K Kensington anti-theft device, 13, 19, 150 Keystone correction, 47 to 48, 100, 140, 157 Keyword, 61 L Lamp number of hours used, 130 ordering, 12 replacing, 126 to 129 specifications, 157 status light, 135 to 136 Lamp timer, resetting, 129 Language setting, 108 Laptop computer connecting to, 20 to 23 display problems, 4
P Password protection, 102 to 104 remote access, 61 request code, 104 PEAP authentication, 88 to 89 Photo color mode, 49 Picture source, selecting, 42, 52 Picture, see Image PIN code method, 79, 83 to 84 Pointer shape, 101 Pointer tool, using, 55 Positioning image, 45 to 46 projector, 17 to 19, 149 to 150 Power button, 39 specifications, 158 status light, 39, 135 to 136 Presentation color mode, 49 Presentations computer, 19 to 23 digital camera, 35 to 36 room conditions, 17, 52 tips and training, 11 using t
Remote control A/V Mute button, 53 as wireless mouse, 56 battery used, 157 controlling multiple projectors, 57 to 58 correcting color, 49, 96 to 98 E-Zoom button, 54 Freeze button, 53 ID, 58 numeric keypad, using, 103 pointer tool, using, 55 problems, 145 range, 157 specifications, 157 switching sources, 52 troubleshooting, 145 Remote Receiver setting, 101 Replacing lamp, 126 to 129 Request code, password, 104 Resetting lamp timer, 129 Resetting menu options, 95 Resize image, 50 Resolution, 50, 139, 155 Res
Transporting projector, 131 Troubleshooting blank screen, 42 to 44, 137 to 139 cut-off image, 139 to 140 distorted image, 47 to 48 EasyMP problems, 144 EMP Monitor problems, 144 EMP NS Connection problems, 144 image and sound problems, 137 to 143 network problems, 143 to 144 no signal, 42 to 43, 138 to 139 projector problems, 133 to 147 remote control problems, 145 tapered image, 47 to 48 Turning off picture (using A/V Mute), 53 Turning off projector, 40 U Unpacking projector, 16 USB, display, 21 to 22 Use
