PowerLite 84 Multimedia Projector ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
- Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 8 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 Using the Remote Control . . . . . . . . . . . . . . . . . . . 29 Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Replacing the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 30 Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 31 Switching Between Picture Sources . . . . . . . . . . . . . . . . 31 Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 32 Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 Using the Projector on a Network . . . . . . . . . . . 53 5 Fine-Tuning the Projector . . . . . . . . . . . . . . . . . . . 61 6 Maintaining the Projector . . . . . . . . . . . . . . . . . . . 77 7 Solving Problems Connecting to a Wired Network . . . . . . . . . . . . . . . . . . . . . 54 Configuring Basic Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Using Projector E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . . 58 Using SNMP to Monitor the Projector. . . . . . .
Solving Network Problems . . . . . . . . . . . . . . . . . . . . . . . . . 100 Solving Problems with the Remote Control . . . . . . . . . . . . 101 Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Speak to a Support Representative . . . . . . . . . . . . . . . . 102 A Projector Installation . . . . . . . . . . . . . . . . . . . . . . . 105 B Technical Specifications . . . . . . . . . . . . . . . . . . . . 107 C Notices . . . . . . . . . . . . . . . . . . . . . . . . .
- Welcome The PowerLite ® 84 is an easy-to-use projector that weighs less than 7 pounds. From classrooms to boardrooms, your full-color presentations and videos will be bright and vibrant even in ordinary indoor lighting. You can connect the projector to a wide range of computers and video sources. Easy setup, control, and security: ■ 8.5-second startup time and Instant Off ® feature for fast setup and shut down ■ Automatic digital keystone correction ■ Closed captioning ■ 1.
Using Your Documentation This electronic User’s Guide provides detailed instructions on using your projector. In addition, your projector software CD-ROM includes the EMP Monitor Operation Guide. Refer to this manual for detailed instructions on monitoring the projector from a remote location. Please follow these guidelines as you read through this manual: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment.
Registration and Warranty Your projector comes with a warranty that lets you project with confidence. For details, see the warranty statement included with your projector. In addition, Epson offers free Extra CareSM Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually via overnight delivery. See the brochure included with your projector for details.
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: PDF manual and registration CD-ROM Projector Projector software CD-ROM Remote control and 2 AA batteries Carrying case Security sticker Power cord VGA computer cable USB cable Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location.
Projector Parts Front Lamp cover Security slot Control panel Remote receiver Air filter A/V mute slide lever Foot release lever Air filter cover switch Security bar A/V mute slide Back S-Video port USB Type B port Computer1 and 2 ports and audio jacks LAN port Video port Audio L-R input jacks Remote receiver Rear adjustable foot Speaker Microphone jack Power inlet RS-232 serial port Monitor Out port Rear adjustable foot Welcome 11
Control Panel Adjusts volume Opens menu system Turns projector on and off Corrects Keystone Cancel/exit Indicate projector status Opens help system Adjusts volume Searches for source image Corrects Keystone Additional Components Depending on how you plan to use the projector, you may need additional components: 12 Welcome ■ To receive an S-video signal, you’ll need an S-video cable. One may be provided with your video equipment, or you can purchase one from Epson; see the list on page 13.
Optional Accessories To enhance your use of the projector, Epson provides the following optional accessories: Product Part number Replacement lamp V13H010L50 Air filter replacement set (2 filters) V13H134A22 Image presentation camera (ELPDC05) V12H162020 DC-10s document camera ELPDC10S DC-06 document camera V12H321001 Wheeled soft case Soft shoulder case for projector and laptop ATA molded hardshell case SwissGear® backpack ELPKS62 ELPKS61 ELPKS58 ELPKS63 Universal projector ceiling mount Adva
Welcome
1 Displaying and Adjusting the Image W hether you’re presenting from a computer or video equipment, you need to follow some basic steps to display your image on the screen.
Positioning the Projector note You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 105 for details. If the projector isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.
Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be at about the level of the bottom of the screen. note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector. You can purchase this from Epson; see page 13.
Turning On the Projector note You can set the projector to automatically turn off the lamp and enter “sleep mode” when it has not received any signals or the A/V Mute slide remains closed for a period of time. This conserves electricity, cools the projector, and extends the life of the lamp. To enable sleep mode, see page 75. Follow these steps to turn on the projector: 1. Open the A/V Mute slide (lens cover). 2.
3. Press the Ppower button on the remote control or on top of the projector. The projector beeps once and the Ppower light flashes green as the projector warms up, then an image begins to appear. When the Ppower light stops flashing and remains green, the projector is ready for use. 4. If you are prompted to enter a password, see page 69. warning Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.
Shutting Down the Projector note Lamp life results will vary depending on mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. This projector incorporates Instant Off technology. To turn it off, you can press its Ppower button as described below, unplug it, or turn off a power switch that supplies power to the projector. You don’t have to wait for the projector to cool off first. 1.
You can also use the Source buttons on the remote control to switch between devices connected to the ports identified on each button. (The LAN button does not work with the PowerLite 84.) Troubleshooting Display Problems Follow these guidelines if you’re having trouble displaying an image. You Can’t Project an Image If you don’t see the image you are trying to project, try the following: ■ Make sure the cables are connected correctly, as described beginning on page 39.
The Projector and Notebook Don’t Display the Same Image If you’re projecting from a notebook, and you can’t see your image on the projection screen and on your computer at the same time, follow these guidelines. If you’re using a PC notebook: ■ On most systems, there’s a function key that lets you toggle between the LCD screen and the projector, or display on both at the same time. It may be labeled CRT/LCD or have an icon such as . You may have to hold down the Fn key while pressing it.
4. Click the Arrangement (or Arrange) tab. Make sure Mirror Displays is checked 5. Make sure the Mirror Displays checkbox is selected. Adjusting the Image Once you see your image, you need to make certain adjustments: ■ If the image is too high or too low, you can reposition it. See page 24. ■ To focus or zoom your image, see page 24. ■ If the image isn’t square, see page 25. ■ If a computer image displays incorrectly, see page 27. ■ If you need to fine-tune the image and/or sound, see page 61.
Adjusting the Height of Your Image If the image is too low on the screen, you can use the front adjustable foot to raise it. 1. Stand behind the projector. Press the foot release lever up and lift the front of the projector. 2. Once the image is positioned where you want it, release the lever to lock the foot in position. 3. If necessary, you can fine-tune the height or level of the image by turning the projector’s adjustable rear feet.
If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 33 for instructions. Adjusting the Image Shape In most cases, you can maintain a square or rectangular image by placing the projector directly in front of the center of the screen with the base of the lens level with the bottom of the screen.
Using Keystone Correction To adjust your image when it is wider on the top or bottom, do the following: ■ Press one of the two keystone correction buttons on the projector’s control panel, as shown below. Continue pressing the button until you are satisfied with the shape of the image. ■ Or press the Menu button on the remote control or projector, select the Settings menu, and press Enter. tip You can display a test pattern to help align the image (see page 68).
Correcting Computer Images If you’re connected to a computer and the image doesn’t look right, press the Auto button on the remote control or the Enter button on the projector. This automatically resets the projector’s tracking, sync, resolution, and position settings. note The Auto button works only with computer images projected through the VGA port. If the Auto button doesn’t correct the problem, you may need to adjust the tracking or sync using the projector’s Signal menu.
Displaying and Adjusting the Image
2 Using the Remote Control T he projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 20 feet away. You can use the remote control to adjust the picture and sound (page 31) or to adjust the color mode for various environments (page 35).
note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes. Using the Remote Control Follow these tips for using the remote control: ■ Point the remote control at the front of the projector or at the screen. ■ Stand within 20 feet of the projector. ■ Avoid using the remote under bright fluorescent lamps or in direct sunlight, or the projector may not respond properly.
Controlling the Picture and Sound You can use the remote control to preview and select your picture sources, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, and adjust the volume.
Turning Off the Picture and Sound You can use the A/V Mute button on the remote control to turn off the image and sound. This does the same thing as the A/V Mute slide (shown on page 18) and is useful if you want to temporarily redirect your audience’s attention. ■ To turn off the picture and sound, press the A/V Mute button. The screen turns black. ■ To turn the image and sound back on, press the button again. You can have the screen turn blue when you press the A/V Mute button.
Zooming Part of Your Image You can zoom in on a portion of the image using the E-Zoom buttons on the remote control. 1. Press the E-Zoom button on the remote control. You see a crosshair indicating the center of the zoom-in area. 2. Use the pointer buttons to position the crosshair. button to enlarge the selected 3. Continue pressing the E-Zoom area up to 4× magnification. 4. While the image is enlarged, you can: ■ Use the pointer buttons to move around the screen.
Adjusting the Aspect Ratio You can use the Aspect button on the remote control to adjust how an image fits into the display area. Each time you press the button, the projector changes to the next setting. When Connected to Video Equipment If you’re projecting from video equipment such as a DVD player, set the projector’s Aspect setting to match that of the player. For example, if the video player is set to output images at a 16:9 aspect ratio, set the projector’s Aspect setting to 16:9 so they match.
When Connected to a Computer note For computer images, Normal is usually the best setting to select. This displays the image at the largest possible size without stretching it. Depending on your computer display, you may see black bars at the edges. In that case, try selecting 16:9.If the resolution of the image is the same as the projector’s, changing the Aspect setting has no effect. If part of the image remains cut off, check the projector’s Resolution setting (see page 66).
Operating Your Computer with the Remote Control If you connect a computer to the projector with a USB cable, as described on page 42, you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering slideshow-style presentations, since you won’t have to stand next to the computer to change slides. ■ Use the Page Up and Down buttons to move through a slideshow.
Highlighting Your Presentation You can display a pointer to call out important information on the screen. If you want to customize the pointer tool, you can choose from three alternative shapes. Using the Pointer Tool 1. To activate the pointer tool, press the Pointer button on the remote control. A pointer appears on the screen. Pointer If you prefer to use a different style of pointer, see the instructions in the next section. 2.
Using the Remote Control
3 Connecting to Computers and Other Equipment T his chapter tells you how to connect the projector to a notebook or desktop computer, and/or to video equipment, such as a VCR, DVD player, or video camera. You can also connect the projector to a microphone, or external speakers.
Connecting to a Computer note Don’t try to force a connector to fit a port with a different shape or number of pins. You may damage the port or connector. You can connect the projector to any computer that has a standard VGA output (monitor) port, including desktop models, PC notebook computers, MacBook®, PowerBook®, and iBook® systems, and hand-held devices. You can also connect to the USB port on a Windows® computer. ■ To connect to your computer’s VGA port, see the instructions below.
3. When you’ve finished making any connections, see page 18 for instructions on turning on the projector and adjusting the image. Once the projector is turned on, select the image source: press the Search button on the remote control or the Source Search button on the projector’s control panel. Connecting to the USB Port You can connect a Windows Vista®, Windows XP, or Windows 2000 (SP4) computer to the projector’s Type B (square) USB port and project your computer’s display.
6. Connect the flat end of the cable to any available USB port on your notebook or desktop computer. Messages appear as the projector is recognized and the software installation begins. note Next time you connect via USB, you won’t have to wait for the software to install. 7. Follow the instructions on your computer screen to install the Epson USB Display software. If you see a “Digital Signature Warning,” select Continue. You will only need to install the software the first time you connect. 8.
2. Connect the square end of the cable to the projector’s Type B (square) USB port. USB cable 3. Connect the flat end of the cable to any available USB port on your notebook or desktop computer. 4. Set the USB Type B setting in the projector’s Extended menu to Wireless Mouse (see page 75). 5. Press the Computer button on the remote control to select your computer as the source. (The wireless mouse function doesn’t work when other sources are selected.) 6.
note To use an external monitor, your computer must be connected to the Computer1 port. Connect the monitor’s cable to the projector’s Monitor Out port as shown. Connecting to Video Equipment RCA connector (composite video) You can connect several video sources to the projector at the same time.
Connecting a Composite Video Source 1. Locate an RCA-style video cable (one is usually provided with your video equipment or you can purchase one from an electronics dealer). 2. Connect the cable to the yellow video output connector on your player and the yellow Video connector on the projector: Connect video cable 3. If you want to play sound through the projector, see page 49 for instructions on connecting audio cables. 4.
Connecting an S-Video Source 1. Locate an S-video cable (one is usually provided with your video equipment or you can purchase one from Epson; see page 13). 2. Connect the cable to the S-video connector on your player and the S-Video connector on the projector: Connect S-video cable 3. If you want to play sound through the projector, see page 49 for instructions on connecting audio cables. 4.
Connecting a Component Video Source You will need a component-to-VGA cable, or a component video cable and adapter, for this connection. You can order the component-to-VGA cable (ELPKC19) from Epson; see page 13 for more information. 1. Connect the VGA-end of the cable to the blue Computer1 or Computer2 connector on the projector. Component-toVGA cable (ELPKC19) Connect componentto-VGA cable 2.
Connecting an RGB Video Source 1. Locate the VGA computer cable provided with the projector. note Make sure the Input Signal setting in the Signal menu is set to Auto or RGB Video (see page 67). 2. Connect the cable to the video port on your player and the Computer1 or Computer 2 port on the projector. Connect to RGB video source 3. If you want to play sound through the projector, see page 49 for instructions on connecting audio cables. 4.
Playing Sound Through the Projector You can play sound through the projector’s speaker system or attach an external speaker system. You can also connect a microphone and output the sound through the projector. Volume buttons on the projector or the You can use the or remote control to adjust the volume. Playing Computer Audio For laptop and most desktop computers, use a 3.5 mm stereo mini-jack cable, which you can purchase from a computer or electronics store. 1.
Playing Sound from Video Equipment For video equipment, use an RCA-style audio cable, which you can purchase from an electronics store. note If you are using the component-to-VGA cable, you will need to connect an audio adapter to use the Audio1 or Audio2 jack. 1. Connect the red and white plugs on one end of the cable to the L and R Audio jacks on the projector. Connect to audio-out ports for video equipment 2.
Connecting External Speakers You can output sound from the projector to external speakers with a built-in amplifier. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a standard audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may need a special cable or adapter. 2. Connect the stereo mini-jack end of the audio cable to the Audio Out port on the projector. Audio cable 3.
Connecting to Computers and Other Equipment
4l Using the Projector on a Network I f you connect your projector to a network, you can monitor it through the network. You can use EMP Monitor (available for Windows only) to monitor and control your projector through the network. For information on installing and using EMP Monitor, see the EMP Monitor Operation Guide.
Connecting to a Wired Network With a shielded, Category-5 Ethernet cable, you can connect the projector to your network and configure it with an IP address. 1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the LAN port on the projector as shown. Network cable 2. Connect the other end to your Ethernet hub or router. 3. Point the remote control at the projector and press the Ppower button.
4. Press the Menu button on the remote control, select the Network menu, then press Enter. 5. Choose Network Configuration and press Enter. 6. Select the Wired LAN menu and press Enter. 7. Choose IP Settings and press Enter. You see a screen like the following: 8. Do one of the following: ■ If your network assigns addresses automatically, turn on the DHCP setting.
To enter numbers, use the buttons on the remote control to highlight the number you want to input, then press the Enter button. When you’re finished entering an address in the network menu, highlight Return, then press the Enter button. 9. To prevent the IP address from appearing on the standby screen, set the IP Address Display setting to Off. 10. When you’re done making all necessary changes, select Complete and press the Enter button to save your settings. Then press Enter again to confirm.
4. Make sure the projector has a unique name, so you can identify it on your network. If you need to rename it, highlight the Projector name text box then press Enter. 5. Use the buttons on the remote control to select individual letters; then press Enter to input a character. To add a blank space or to navigate backward and forward through the input text, highlight the arrows and press Enter. To toggle symbol settings or capital letters, highlight the option and press Enter.
Using Projector E-mail Alerts When this feature is enabled, the projector sends you an e-mail alert if it has any problems. 1. Press the Menu button on the remote control, select the Network menu, then press Enter. 2. Choose Network Configuration and press Enter. 3. Choose Mail, then press Enter. You see the following screen: 4. Highlight On to receive email notifications, then press Enter. 5. Enter the IP address for the SMTP server for the projector.
When the selected problem or warning occurs, an e-mail message is sent to the specified notification addresses. The subject line of the e-mail is EPSON Projector.
224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255). 5. If your network environment uses an AMX controller, select ON to allow the projector to be detected by AMX Device Discovery. Using a Browser to Control the Projector You can use a standard web browser to monitor and control the projector through the network. 1. Make sure that the projector is set up for your network, as described on page 54.
5 Fine-Tuning the Projector Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options Menu list The menus are listed on the left and the options available for the highlighted menu are shown on the right. 2.
3. Once you’ve selected the menu, use the pointer buttons to scroll through the list of options. (Some of the options may be grayed out or unavailable, depending on the selected source.) 4. After highlighting the option you want to adjust, use the pointer buttons to change the setting. In some cases, you may have to press the Enter button to view a sub-screen for changing the setting. ■ Press the left or right arrow button to adjust a slider bar, then press Enter.
To restore all the projector settings to their factory-default values, select the Reset menu, highlight Reset All, and press Enter. note When you select Reset All in the Reset menu, it does not reset the Computer Input, Video Signal, User’s Logo, Language, or Lamp settings. Adjusting the Image You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast. 1. Press the Menu button on the projector or remote control and select the Image menu. You see the Image menu screen. 2.
■ Tint (video only) Adjusts the balance of green to magenta in the image (available only for component video or NTSC signals). ■ Sharpness Adjusts the sharpness of the image. ■ Color Adjustment Adjusts the color values. Select Abs. Color Temp. to adjust the overall value from 5000 and 10000 °K. Or, select Red, Green, Blue to adjust the saturation values for each color. (Not available if sRGB is selected as the Color Mode setting.
2. Use the pointer buttons to highlight the desired option, then adjust it as needed: ■ Auto Setup Leave this setting on to automatically optimize the image when Computer is selected as the source. Turn it off if you want to save adjustments you have made to the video settings. ■ Resolution When set to Auto, the resolution (size) of a computer image is automatically detected so it can be scaled to fit in the projection area.
■ Input Signal If the colors don’t look right on the Auto setting, select the setting for the type of equipment you’ve connected to the Computer1 or Computer2 port: RGB: For a computer connection. Component Video: For a video player that outputs a component video signal. ■ Video Signal Leave this setting at Auto unless you are using a 60-Hz PAL system (then select PAL60). ■ Aspect Choose an aspect ratio setting that allows the image to fit best in the display area. See page 34 for details.
■ Auto Keystone Automatically compensates for keystone distortion when the projector is tilted upward. This feature is available only when the projector is set for front projection (it is enabled by default). ■ Control Panel Lock Lets you disable the buttons on the projector. See page 73 for more information. ■ Pointer Shape Lets you choose from three alternative pointer shapes. See page 37 for more information. ■ Brightness Control Lets you select from two levels of brightness.
Using the Projector Security Features To prevent unauthorized use of the projector, you can do the following: ■ Assign a password; this can be disabled for a set period if you want to loan the projector to someone. ■ Create an identifying user logo that is displayed at startup and/or when the A/V Mute button is pressed. See page 72.
The default setting for the Password Protect function is Off. Follow these steps to turn password protection on: 1. Press the Freeze button on the remote control for about five seconds. You see this screen: caution If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times. 2. Use the pointer buttons to set Power On Protect to On. Then press Enter. 3. Press Esc. 4. Select Password and press Enter. 5.
9. To enable network setting protection, select Network Protect and press Enter. Select On and press Enter. When this feature is on, none of the network settings on the menu can be changed. Starting the Projector with a Password When the password function is enabled, you see this screen when you plug in and turn on the projector: Hold down the Num button on the remote control and use the numeric keypad to enter the four digit password.
If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance. See “Where To Get Help” on page 102. Creating Your Own Startup Screen note Once you capture an image, it automatically replaces the Epson startup screen. Although you can change the startup screen, you cannot restore the original one. You can transfer any image from your computer or video source to the projector and then use it as your startup screen.
5. When you see the message Select this Image?, highlight Yes and press Enter. 6. Use the arrow buttons to select a zoom factor (display size) and press Enter. 7. When the message Save this image as the user’s logo? appears, select Yes and press Enter. Saving the logo may take a few moments. Do not use your projector, remote control, or video source while the logo is being saved. 8. When you see the message Completed, press Esc to return to the menu screen.
4. Select Yes and press Enter to confirm the setting. note To unlock the projector, press the Enter button on the projector’s control panel for 7 seconds. 5. Press the Menu button to exit. Customizing Power and Operation You can use the Extended menu to customize the way the projector displays images, enable quick startup, turn sleep mode on or off, and customize other projector operations.
■ Operation Use this menu to enable the following functions: note Direct Power On to have the projector start when the power cable is connected (without pressing the P power button). If Direct Power On is enabled, the power cable is connected, and a power outage occurs, the projector will start when the power is restored. Sleep Mode to have the projector turn off automatically if it is idle (and no signal is received) for the amount of time you select as the Sleep Mode Timer (1 to 30 minutes).
Fine-Tuning the Projector
6 Maintaining the Projector Y our projector needs little maintenance. All you have to do is keep the lens clean. You may also need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. To remove dirt or smears on the lens, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens. Cleaning the Projector Case caution Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case. Before you clean the case, turn off the projector and unplug the power cord.
Cleaning the Air Filter and Vent Your projector includes an air filter to ensure the best performance. If dust collects on the air filter or vent, clean them as described below. Dust clogs prevent proper ventilation and can cause overheating and damage the projector. If you see the following message, clean the air filter immediately. note The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter.
Replacing the Lamp and Air Filter note When you replace the lamp for your projector, you should also replace the filter. The life span of the projection lamp is about 5000 hours if Brightness Control in the Setting menu is set to High (default), and 6000 hours if Brightness Control is set to Low. To check how long the lamp has been in use, see page 93. It is time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate.
4. Loosen the lamp cover screw (you can’t remove it). Then slide the lamp cover and lift it off of the projector. 5. Loosen the two screws holding the lamp in place (you can’t remove them).
6. Hold the lamp as shown and pull it straight out. note The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.) 8. Push down the side marked PUSH until it snaps in.
9. Once the lamp is fully inserted, tighten its screws. 10. Replace the lamp cover, then tighten its screw. 11. Reset the lamp timer as described page 86.
Replacing the Air Filter If the filter is difficult to clean or damaged, or if the overheating message appears after cleaning, you need to replace the filter. Contact your dealer or call Epson at 800-GO-EPSON (800-463-7766) to obtain a new filter. 1. Turn off the projector. 2. When the Ppower light stops flashing, unplug the power cord 3. Open the air filter cover by sliding the switch and pulling down the cover.
4. Grasp the tab and pull the filter straight out. 5. Press in the new air filter until it clicks in place. 6. Close the air filter cover.
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menus. 1. Press the Menu button on the remote control or on the projector’s control panel. You see the main menu. 2. Use the buttons on the remote control (or the arrow buttons on the projector) to highlight Reset, then press Enter. You see this screen: 3. Select Reset Lamp Hours and press Enter. 4. When you see the prompt, select Yes and press Enter. 5.
Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent damage: ■ Close the A/V Mute slide (lens cover) to protect the lens. ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
Maintaining the Projector
7 Solving Problems T his chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on top of the projector or on the remote control. 1. Press the ? Help button on the remote control or on the projector. You see the Help Menu. 2. Use the pointer button on the remote control or the navigational buttons on the projector to highlight menu items. 3. Press the Enter button on the remote control or on the projector to select the menu item. 4.
What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status. Power light Lamp light Temperature light Refer to the following table for a complete description of the projector’s status lights: Status lights Light Status Orange Description The projector is in sleep or standby mode. You can unplug it or press the P power button to turn it on. Flashing green The projector is warming up. Wait for the image to appear. Green The projector is operating normally.
Status lights (continued) Light Status Description Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around the projector for ventilation, and that the air filter and vents are clear. If you’re using the projector above 4900 feet (1500 m), turn on High Altitude Mode; see page 75. Red The projector is overheating, which turns the lamp off automatically.
Viewing Lamp Usage and Other Information Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used. Press the Menu button and highlight the Info menu. You see the lamp usage hours and various input signal settings on the right. The life span of the lamp is about 5000 hours if the Brightness Control setting in the Settings menu is set to High (default), and 6000 hours if the Brightness Control setting is set to Low.
You hear the projector’s fan after the power has been turned off. If Standby Mode is set to Communication On, the fans continue to operate after the projector has cooled down. See page 75 for more information about this setting. Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the Ppower light is green, not flashing. ■ The projector may be in standby or sleep mode. If the Ppower light is orange, press the Ppower button to turn the projector on.
■ If you see a black screen and you are connected through your computer’s USB port, the application may be using DirectX drawing features, which are not supported. You’ve connected a computer and see a blue screen with the message No Signal displayed. ■ Make sure the cables are connected correctly, as described on page 40.
6. Make sure the Mirror Displays checkbox is selected. The message Not Supported is displayed. ■ Make sure the correct Input Signal is selected in the Signal menu (see page 67). ■ Make sure your computer’s resolution doesn’t exceed UXGA (1600 × 1200) and the frequency or refresh rate is supported by the projector (see page 110). If necessary, change your computer’s resolution setting. Only part of the image is displayed.
The image isn’t square, but keystone-shaped. ■ If the top or bottom of the image is broader, press the button on the projector until the image is square. or ■ If the projector is angled toward the screen from the left or right, the image will be broader on one side. Center the projector in front of the middle of the screen, facing the screen squarely. ■ Enable the Auto Keystone feature to automatically fix the shape. See page 68. The image contains static or noise.
■ Make sure the lens is not fogged by condensation. You may need to wait before using the projector after moving it from a cold environment to a warm environment. ■ Make sure the projector is facing the screen squarely, to eliminate the need for keystone correction. ■ Adjust the Sharpness setting on the Image menu (see page 65). When you change video settings, you should be able to see the effect on the screen immediately.
3. Adjust the Sync setting to increase the image sharpness. The image is too light or dark, or colors are incorrect. ■ Press the Color Mode button to select a different color mode (see page 35). ■ Try adjusting the brightness and color settings in the Image menu (see page 64). ■ Try changing the Brightness Control in the Settings menu (see page 68). ■ Check your computer display settings to correct the color balance. ■ The projector’s lamp may need to be replaced. See page 80 for instructions.
■ Make sure the audio cable is connected securely at both ends. For computer audio, connect the cable to your computer’s headphone jack or audio out jack. ■ Make sure the volume control on your computer is not turned all the way down or muted. In Windows, you may be able to use the volume control in your Windows system tray (lower right corner of the screen). On a Mac, you may be able to adjust the volume from your menu bar (top right corner of the screen) or via the volume control function keys.
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. ■ The remote control’s batteries may not be installed correctly or may be low on power. To change the batteries, see page 30. ■ Make sure you are within about 20 feet (6 meters) of the projector and within range of the projector’s front or back sensor (approximately 30° to the left or right and 15° above or below). ■ Dim the room lights and turn off any fluorescent lights.
Where To Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website at www.epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card.
Purchase Supplies and Accessories You can purchase screens, carrying cases, or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
Solving Problems
A Projector Installation T his appendix provides guidelines on installing the projector in a permanent location, such as a classroom or conference room.
If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt the projector down to position the image on the screen. This causes the image to lose its square shape. You can correct the distortion using the Keystone function in the projector’s menu system (see page 67). If you place the projector so that the base of the lens is level with the bottom of the screen, the image should be square and you won’t have to adjust it.
B Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 16.8 million colors Light output High Brightness mode: 2600 lumens white light output (ISO 21118 standard) 2600 lumens color light output Low Brightness mode: 2080 lumens white light output (ISO 21118 standard) 2080 lumens color light output Contrast ratio 2000:1 with auto iris Image size 30 to 300 inches Projection distance 2.7 to 45.
Projection Lamp note Lamp life results will vary depending upon mode selected, environmental conditions, and usage. Turn off this product when not in use to prolong the life of the projector. Type UHE (Ultra High Efficiency) Power consumption 200 W Lamp life Approx. 5000 hours (High Brightness mode) Approx. 6000 hours (Low Brightness mode) Part number V13H010L50 Remote Control Range 20 feet (6 meters) Batteries Two AA Dimensions Height 3.7 inches (95 mm), feet retracted Width 12.
Environmental Temperature Humidity (non-condensing) Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Operating: 20 to 80% RH Storage: 10 to 90% RH Operating altitude 0 to 7,500 ft (0 to 2,286 m) Safety United States FCC 47CFR Part 15B Class B (DoC) UL60950-1 Second Edition Canada ICES-003 Class B CSA C22.2 No. 60950-1-07 Pixelworks™ DNX™ ICs are used in this projector.
Compatible Video Formats The projector supports NTSC, PAL, and SECAM international video standards, as well as the monitor display formats listed below. To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector. Some images are automatically resized using Epson’s SizeWise™ technology to display in the projector’s “native” format (XGA or WXGA).
Mode Refresh Rate (Hz) Resolution SXGA2—60 SXGA2—75 SXGA2—85 SXGA+60 SXGA+75 SXGA+85 60 75 85 60 75 85 1280 × 960 1280 × 960 1280 × 960 1400 × 1050 1400 × 1050 1400 × 1050 SXGA3—60 SXGA3—75 SXGA3—85 60 75 85 1280 × 1024 1280 × 1024 1280 × 1024 UXGA—60 60 1600 × 1200 iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19 MAC19-60 MAC21 117 95 75 67 75 75 59 75 640 × 480 800 × 600 1024 × 768 640 × 480 832 × 624 1024 × 768 1024 × 768 1152 × 870 NTSC PAL SECAM 60 50 50 — — — HDTV (720p) HDTV (720p) HDT
Technical Specifications
C Notices This appendix includes safety instructions and other important information about your PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not look into the lens when the projector is on. The bright light can damage your eyes. ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not operate the projector on its side, or while tilted to one side.
Notices ■ Do not use or store the projector or remote control in a hot location, such as near a heater, in direct sunlight, or in a closed vehicle. ■ Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or set it on top of loose papers, which could block vents underneath your projector. If you are setting up the projector near a wall, leave at least 7.
■ Use the type of power source indicated on the projector. Use of a different power source may result in fire or electric shock. If you are not sure of the power available, consult your dealer or power company. ■ If you use the projector in a country other than where you purchased it, use the correct power cord for that country. ■ Do not overload wall outlets, extension cords, or power strips. Do not insert the plug into a dusty outlet. This can cause fire or electric shock.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Index A C A/V Mute, 32, 73, 94 Accessories, 13 Adapter, audio, 50 Air filter cleaning, 79 ordering, 13 replacing, 80 to 85 Altitude, 75, 109 Anti-theft device, 13, 17 Aspect ratio, 34 to 35, 107 Aspect setting, 34 to 35, 67 Audio adapter, 50 connecting equipment, 49 to 51 controlling volume, 33 problems, troubleshooting, 99 to 100 turning off (using A/V Mute), 32 Auto button, 27 Auto Iris setting, 65 Auto Keystone setting, 68 Auto Setup setting, 66 Cables Ethernet, 54 illustrations, 10 mouse, 42 ordering
D I Default settings, restoring, 63 Direct Power On, 19, 75 Distance from projector to screen, 16, 107 Document camera ordering, 13 Documentation, 8 DVD player, connecting, 44 to 48 Dynamic color mode, 35 Image adjusting, 23 to 27, 64 to 65 blurry, 97 to 98 capturing and saving in projector, 72 to 73 correcting shape, 25 to 26, 67, 97 fitting on screen, 66, 96 height, adjusting, 24 positioning, 66 problems with, 94 to 99 projecting on chalkboard, 35 raising, 24 selecting source, 20 to 21, 31, 45 to 48 si
Lights, status, 91 to 92 Logo, saving on projector, 72 to 73 M Mac display problems, 95 resolution setting, 96 Manuals, 8 Menus changing settings, 62 to 63 default settings, restoring, 63 to 64 Extended, 74 to 75 Image, 64 to 65 Info, 93 Network, 55, 56 Settings, 67 to 68 Signal, 65 to 67 Mic Input Volume setting, 68 Microphone, connecting, 50 Monitor, connecting, 43 Monitoring projector e-mail notifications, 58 to 59 EMP Monitor, 53 SNMP, 59 to 60 using browser, 60 Mouse compatibility, 107 connecting cabl
Projector carrying case, 10, 13, 87 cleaning, 78 disabling buttons, 73 to 74 distance from screen, 16, 107 installing, 105 to 106 lamp specifications, 108 monitoring remotely, 58 to 60 options, 13 parts, 11 password protection, 69 to 71 positioning, 16 to 17 resolution, 107 specifications, 107 to 109 transporting, 87 troubleshooting, 89 to 101 turning off, 20 turning on, 17 to 19 unpacking, 10 viewing information about, 93 R Raising image, 24 Rear-screen projection, 74, 105 to 106 Registration, 9 Remote co
sRGB color mode, 35 Startup screen, creating, 72 to 73 Status lights, 91 to 92 Support, see Technical support S-video cable, 13, 46 Switching picture source, 20 to 21, 31 Sync setting, 66 Synchronization, adjusting, 27, 98 to 99 T Technical support, 8, 102 to 103 Temperature requirements, 109 status light, 91 to 92 Temperature, color, 65 Test pattern, displaying, 26, 68 Theatre color mode, 35 Tint setting, 65 Tracking, adjusting, 27, 66, 98 to 99 Transporting projector, 87 Troubleshooting blank screen, 21
