PowerLite 83V+ Multimedia Projector ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 8 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 9 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 9 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Projector Parts . . . . . . . . . .
2 Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 3 Using the Remote Control . . . . . . . . . . . . . . . . . . . 43 4 4 Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 34 Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 34 Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 36 What To Do If You See a Blank Screen . . . . . . . . . . . . . 36 Adjusting the Image . . . . . . . . . . . . . . . . . .
Using the Projector’s Security Features. . . . . . . . . . . . . . . . . Creating Your Own Screen Logo. . . . . . . . . . . . . . . . . . Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turning On the Password and User’s Logo . . . . . . . . . . Starting the Projector with a Password. . . . . . . . . . . . . . Disabling the Projector’s Buttons . . . . . . . . . . . . . . . . . Installing Security Locks . . . . . . . . . . . . . . . . . . . . . . . .
Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . . 92 Compatible Computer Display Formats. . . . . . . . . . . . . . . . 93 B Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 97 FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . 99 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
- Welcome The PowerLite ® 83V+ is a portable projector that weighs less than 7 pounds, and offers up to 2200 lumens of brightness (white light output and color light output). From classrooms to boardrooms, your full-color presentations and videos will be bright and vibrant even in ordinary indoor lighting. Images are displayed at a native resolution of 1024 × 768 pixels. Epson 3LCD technology ensures true to life color and remarkable saturation, even in well-lit rooms.
Getting the Most from Your Projector Depending on your presentation, you can take advantage of any or all of these options: ■ Connecting to a laptop or other computer If you want to connect the projector to a laptop or desktop computer, see page 18. For additional presentation control, you can connect an external monitor to view the presentation on your computer simultaneously.
Using Your Documentation In addition to this manual, your documentation includes a Quick Setup sheet, warranty brochures, and an Epson PrivateLine® Support card. The Quick Setup sheet gives instructions to quickly set up your projector and connect it to a computer or video device. This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury.
Registration and Warranty Your projector comes with a basic warranty that lets you project with confidence. For details, see the warranty brochure included with your projector. In addition, Epson offers free Extra CareSM Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada. See the brochure included with your projector for details.
Projector Parts Front Security slot Control panel A/V mute slide lever Lamp cover Zoom ring Focus ring Air exhaust vent A/V mute slide Front adjustable foot Foot release lever Back S-Video port Video port Remote control sensor Audio L-R input ports Computer 1 and 2 (Component Video) ports Audio 1 and 2 input ports Remote control sensor Speaker Audio Out port Monitor Out port (for Computer1 port output only) Power inlet RS-232C serial port Rear adjustable foot Bottom Air filter Holes for ceil
Control Panel Turns projector on and off Opens menu system Up/down arrows and keystone correction Cancel/exit Opens help system Indicate projector status Searches for source image Left/right arrows and Volume down/up Enter Additional Components Depending on how you plan to use the projector, you may need additional components: 12 Welcome ■ To receive an S-Video signal, you need an S-Video cable. One is usually provided with your video device or you can purchase it from Epson. See page 13.
Optional Accessories To enhance your use of the projector, Epson provides the following optional accessories: Product Product number Replacement lamp V13H010L42 Air filter set (includes 2 filters) V13H134A13 Component-to-VGA video cable S-Video cable ELPKC19 ELPSV01 Distribution amplifier ELPDA01 50-inch portable screen (4:3 aspect ratio) 80-inch portable pop-up screen (4:3 aspect ratio) Accolade® Duet™ Ultra Portable Projector screen (4:3 and 16:9 aspect ratio) ELPSC06 ELPSC08 ELPSC80 DC-06 doc
Welcome
1 Setting Up the Projector T his chapter tells you how to set up the projector and connect it to a computer or video source. You can connect up to four devices simultaneously: four video sources, or two computer and two video sources.
Positioning the Projector Before connecting the projector, you need to decide where to place it. If you’re setting up the projector yourself and it isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. note You can use the Image Size Calculator on the Epson website to determine how large an image will be at different projection distances.
Try to place the projector directly in front of the center of the screen, facing it toward the screen squarely. If the projector isn’t positioned this way, the image will be “keystone” shaped, instead of square or rectangular. If you place the projector below the level of the screen, you’ll have to tilt it up by extending the front adjustable foot, as described on page 39. This also causes the image to lose its rectangular shape.
Connecting to a Computer note If you have an iBook with an RCA video-out port, follow the instructions for connecting to a video device on page 25. You can connect the projector to any computer that has a standard VGA or BNC monitor port, including PC notebook and laptop computers, Macintosh PowerBooks and iBooks, and hand-held devices. Follow the instructions in this section to: ■ Connect the projector to your computer with the VGA cable included with the projector.
Connect one end of the cable to the projector’s Computer1 or Computer2 port. Computer1 and Computer2 ports 3. Connect the other end of the cable to your computer’s video-out or monitor port. 4. If you connected the computer to the Computer1 port and you want to view the display simultaneously on your computer monitor and the projector screen, see “Connecting an External Monitor” on page 21. 5.
2. Connect the cable’s VGA connector to the projector’s Computer1 or Computer2 port. Computer1 and Computer2 ports 3. Connect the BNC connectors to your computer’s BNC ports. 4. If you want to view the display simultaneously on your computer monitor and the projector screen, see “Connecting an External Monitor” on page 21. 5. To play audio from your computer through the projector speakers, see “Playing Sound Through the Projector” on page 22. 6. Tighten the screws on the VGA connector.
Connecting an External Monitor If you want to see your presentation close-up as well as on the projection screen, you can connect an external monitor to the projector. This lets you view images on your computer monitor while the projector is in standby mode (plugged in but not turned on) and check your presentation or switch between picture sources even if you’ve pressed the A/V Mute button on the remote control to turn off projection on the screen.
Playing Sound Through the Projector You can connect a commercially available 3.5 mm stereo mini-jack audio cable to take advantage of the projector’s built-in speaker. You can obtain the audio cable from a computer or electronics dealer. 1. Connect one end of the 3.5 mm stereo mini-jack audio cable to the corresponding Audio1 or Audio2 jack on the projector. Audio1 and Audio2 jacks 2.
Connecting External Speakers You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projector’s built-in speaker system is disabled. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter. 2.
Connecting to Video Sources You can connect a DVD player, VCR, camcorder, digital camera, gaming console, or any other compatible video source to your projector. You can connect up to four video devices at one time. note The projector does not support TV antenna cable F connectors. The projector supports HDTV, SDTV, NTSC, PAL, and SECAM, and automatically detects the video format. It can receive composite video, S-Video, RGB video, and component video.
Connecting a Composite Video Source If you’re connecting a composite video device, use a commercially available RCA A/V cable. Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Connect the yellow RCA plug on one end of the cable to the projector’s yellow Video port. Video port 2. Connect the yellow plug on the other end of the cable to the video-out port on your video source. 3.
Connecting an S-Video Source If your video source has an S-Video jack, you can use it to project a higher quality video image. You’ll need an S-Video cable, which is usually provided with your video source, or you can purchase one from Epson (part number ELPSV01). See page 13 for ordering information. Before starting, make sure the projector and your DVD player or other video source are turned off. 1.
Connecting an RGB Video Source Follow these instructions to connect the projector to a video player or satellite receiver that has an RGB video output port using the VGA computer cable that came with the projector. Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Connect one end of the VGA computer cable to the Computer1 or Computer2 port on the projector. Computer1 and Computer2 ports 2. Connect the other end to the video port on your player. 3.
Connecting a Component Video Source If your video source has component video connectors, you can use them to project a higher quality video image. You’ll need a component-to-VGA video cable, which can be purchased from Epson (part number ELPKC19). See page 13 for ordering information. Before starting, make sure the projector and your DVD player or other video device are turned off. 1. Connect the 15-pin VGA connector end of the component-to-VGA video cable to the projector’s Computer1 or Computer2 port.
Playing Sound Through the Projector The projector has a built-in speaker with a maximum output of 10 W. You can play sound from your video equipment through the projector’s speaker if your video device has an audio output port. For RCA-Type Audio Output Ports Most video devices have an RCA-type audio output port. In this case, use a commercially available RCA-type audio cable to connect the projector to your video source: 1. Connect one end of the RCA audio cable to the L-Audio-R jacks on the projector.
For Stereo Mini-Jack Audio Output Ports Some video devices, especially camcorders, may have a stereo mini-jack audio output port. To connect to the L-Audio-R input jacks when using the S-Video or Video port, use a commercially available stereo mini-jack audio adapter cable (3.5-mm stereo miniplug to two male RCA plugs) to connect to the projector. 1. Connect one end of the audio adapter cable to the L-Audio-R jacks on the projector. L-Audio-R jacks 2.
Connecting External Speakers You can output sound to external speakers with built-in amplifiers. When you play sound through external speakers, the projector’s built-in speaker system is disabled. 1. Locate the appropriate cable to connect your speakers. Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter. 2.
Setting Up the Projector
2 Projecting Once you’ve set up the projector, you’re ready to turn it on, adjust the image, and give your presentation. Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote.
Turning On Your Equipment Make sure your projector and other equipment are set up and connected correctly, as described in Chapter 1. Then turn on your projector, as described below. If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually. See page 36.
3. Connect the other end to an electrical outlet. The P Power light on top of the projector turns orange, indicating that the projector is receiving power but not yet turned on. 4. Turn on your computer or video source if you have not already. 5. Press the P Power button on the projector or on the remote control to turn it on. note If you are using the remote control for the first time, be sure to insert the batteries as described on the Quick Setup poster.
Selecting the Image Source note The name of the selected image source appears briefly in the upper right corner of the screen. Selecting the image source lets you switch between images input from different pieces of equipment connected to the projector (such as a computer and DVD player). If you don’t see the image you want, press the Source Search button on the remote control or projector until the correct device image is projected. If a projected image fails to appear, see the next section for help.
■ If you’re projecting from a laptop, and you don’t see the same image on the projection screen and computer screen, check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control Panel, open the Display utility. Click the Settings tab, then click Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled.
Adjusting the Image Once you see your image, you’ll need to make certain adjustments: ■ To focus or zoom your image, see below. ■ If the image is too high or too low, you can reposition it. See page 39. ■ If the image isn’t square, see page 40. ■ To adjust image brightness, see page 40. ■ If a computer image displays incorrectly, see page 41. You can make many other adjustments to the image—such as changing the brightness, contrast, and aspect ratio—using the projector’s menu system.
Adjusting the Height of Your Image If the image is too high or low, you can correct it by adjusting the projector’s front foot. 1. Stand behind the projector. Press up on the blue foot release lever and lift the front of the projector to extend the front adjustable foot. 2. Once the image is positioned where you want, release the lever to lock the foot in position. The projector automatically corrects images that are distorted when the projector is tilted up or down (up to a 30° tilt).
Adjusting the Image Shape If the projector is tilted up or down, the images that are displayed will be distorted. To correct the distortion or “keystone” shape, do one or more of the following: ■ If your image looks like or , you’ve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely. ■ If your image looks like or , you need to adjust the keystone correction value.
Correcting Computer Images If you’ve connected a computer and the image doesn’t look right, or it doesn’t fit properly on the screen, press the Enter button on the projector or the Enter/Auto button on the remote control. This automatically resets the projector’s tracking, sync, resolution, and position settings. You must be projecting a computer image for this button to have any effect. Additionally, if the Auto Setup option in the Signal menu is set to Off, the Auto function will not work. See page 55.
Shutting Down the Projector note When the projector has not received any input signals for 30 minutes, it automatically turns off the projector lamp and enters “sleep mode.” This conserves electricity, cools the projector, and extends the life of the lamp. If you are done using the projector, unplug the power cord. If you want to start projecting again, press the P Power button. You can turn sleep mode on or off through the Extended menu. See page 59.
33 Using the Remote Control T he remote control lets you access your projector’s features from anywhere in the room—up to 20 feet away. For example, you can turn the projector on and off, freeze the presentation, zoom in on a portion of your image, and access the menu system. (The projector menus let you adjust many projector settings; see Chapter 4.) When using the remote control, stand within 20 feet of the projector.
Controlling the Picture and Sound You can use the remote control to select your source, adjust the colors, temporarily turn off the picture and sound, freeze the action, or zoom in on the picture. Make sure you have set up your projector and connected any equipment as described in Chapter 1.
Adjusting the Color Mode You may want to adjust the color mode to select a different setting that is appropriate for the image you’re projecting and the environment in which you’re projecting it. Press the Color Mode button on the remote control. If you’re projecting computer or RGB video images, the default color mode is Presentation, which is appropriate for full-color presentations in bright rooms. Color Mode button The following table lists the color modes available.
Turning Off the Picture and Sound Press the A/V Mute button on the remote control or use the A/V Mute slide on the projector to turn off the image and sound and darken your screen. This is useful if you want to temporarily re-direct your audience’s attention without the distraction of a bright screen. ■ To turn off the picture and sound, press the A/V Mute button or close the A/V Mute slide on the projector. The screen goes dark.
Zooming Your Image Follow these steps to zoom in on a portion of the image: 1. Press the E-Zoom + button on the remote control. Arrow buttons You see a crosshair indicating the center of the zoom-in area. 2. Use the four “arrow” buttons on the remote control to position the crosshair in the area you want to enlarge. E-Zoom buttons 3. Continue pressing the E-Zoom + button to enlarge the selected area up to 4 times. 4. While the image is enlarged, you can: ■ Use the arrow buttons to pan about.
Replacing the Batteries The remote control uses two AA alkaline batteries. Follow these steps when you need to replace them: note The remote control automatically shuts off when it detects a button being pressed more than 30 seconds. This conserves battery life. It can be helpful, for example, when the remote is in a carrying case and the P Power button is accidentally pushed. 1. Press in the tab to remove the battery cover. 2. Remove the old batteries, then insert the new ones as shown.
433 Fine-tuning the Projector You can use the Menu button on the projector or remote control to access on-screen menus to adjust the image, sound, and other features.
Using the Projector’s Menu System The projector menus let you adjust and customize the projector features: 50 ■ The Image menu lets you modify the colors of the projected image and fine-tune brightness, contrast, and sharpness. See page 52. ■ The Signal menu lets you make adjustments to the input signal. You can select your input source, change the image position and aspect ratio, and adjust tracking and sync for computer images. See page 54.
Changing Menu Settings Use the buttons on the remote control or on the projector to access the menus and change settings. Follow these steps: 1. Press the Menu button on the remote control or projector to display the menu screen: Menu options Menus The menus are listed on the left, and the options available for the highlighted menu are shown on the right. 2. Use the up and down arrow buttons on the projector or remote control to scroll through the menu list.
Press the left or right arrow buttons on the projector or the remote control to adjust a slider bar. To select from two or more settings, use the up or down arrow buttons on the projector or the remote control to highlight the desired setting, then press Enter. 5. Press the Esc button to return to the previous menu or to close the menu system if you are at the main menu. Your changes are saved automatically. 6. Press the Menu button to exit the menu system.
Follow these steps to adjust the appearance of your image: 1. Press the Menu button. You see the main menu. 2. Press Enter to select the Image menu. 3. Use the up and down arrow buttons and press Enter to set the following options: ■ Color Mode Corrects the vividness of image color. You can select from the following settings, and save a different one for each computer and/or video source: Photo: For projecting still images with vivid color in a bright room (Computer input only).
■ Tint (component, composite, and S-Video) Adjusts the balance of green to magenta in the image. ■ Sharpness Sharpens or softens the image. ■ Color Adjustment Adjusts the temperature and intensity of red, green, and blue. 4. When the image is set correctly, press Esc or Menu. Your settings are automatically saved. Adjusting the Input Signal Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to manually select it.
3. Press Enter. Then use the up and down arrow buttons and the Enter button to set the following options: ■ Auto Setup (computer images) Leave this setting On to automatically optimize the computer image. Turn it off if you want to save adjustments you have made to the video settings. ■ Tracking (computer images) Removes unwanted vertical lines from a computer image by matching the projector’s internal clock to various computer signals. See page 84 for more information.
■ Video Signal (composite and S-Video) Leave this setting at Auto unless you are using a 60-Hz PAL system (select PAL60). ■ Aspect Sets the image’s aspect ratio (ratio of width to height). Select 4:3 for Normal for computer content, 4:3 for letterbox video content, 16:9 for widescreen content, or 16:9 (Up) or 16:9 (Down) for video content with subtitles or supertitles. 4. When you’re finished, press Esc or Menu.
3. Press Enter. Then use the up and down arrow buttons and the Enter button to set the following options: ■ Keystone Adjusts a distorted image from a trapezoid shape to rectangular. ■ Auto Keystone Automatically adjusts a distorted image from a trapezoid shape to rectangular when the projector’s foot is extended or retracted. (Not available when you’re projecting from the ceiling or using rear projection.) Select On or Off.
Selecting Projector Setup Options Use the Extended menu to customize the way you set up the projector. You can configure the projector for rear and/or ceiling projection, change the language for the menus and messages, set the screen background color, capture and store a custom image or logo for the startup screen. 1. Press the Menu button. 2. Select the Extended menu. 3. Press Enter.
■ User’s Logo note Turn on to display the image or logo you have captured whenever the projector is turned on. See page 63 for more information. ■ Logo settings cannot be changed if the User’s Logo Protect feature has been turned on. See page 64. Projection Front: Projector is in front of the screen. Front/Ceiling: Projector is in front of the screen, mounted upside-down from the ceiling. Rear: Projector is behind the screen.
note You can make changes to many of the signal settings on the Signal menu. See page 54 for details. Viewing Lamp Usage and Other Information Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used. 1. Press the Menu button. 2. Select the Info menu.
■ Refresh Rate (computer, RGB video, and component video) Displays the refresh rate. ■ Sync Info (computer, RGB video, and component video) Provides information that may be needed by the service technician. ■ Status Displays informations about projector problems. This information may be needed if service is required. 3. When you’re finished, press Esc or Menu.
note If you should happen to enable the password before you set one and you see the prompt to enter the password, enter the default password 0000 to proceed. If you assign the projector a password, a screen appears requesting the password whenever the projector is turned on. If you enter the password incorrectly three times in succession, the projector’s operation is locked and you’ll need to disconnect the power cord, then reconnect it to redisplay the password screen.
Creating Your Own Screen Logo You can transfer any image on your computer to the projector, and then use it as the startup screen and/or the screen that is displayed when you press the A/V Mute button. The image can be a company logo, slogan, photograph, or any other image you want to use. The projector considers this image the “User’s Logo.” Follow these steps to capture the image and transfer it to the projector: 1. Display the image you want to use on the projector.
7. When you see this screen, select a zoom rate (display size), and then press Enter. note The default setting for the Startup Screen option menu is On. If the Startup Screen is set to Off, the logo will not display at startup. If the User’s Logo Protect function has been set to On, the Display Background setting cannot be changed. You need to turn the protect function off first. See page 65 for details. Once you’ve saved a user’s logo, you cannot reset the logo setting to its factory default (no logo).
3. When you see the message Change the password?, select Yes and press Enter. 4. Enter a 4-digit number using the numeric buttons on the remote control, as shown. The password will be displayed as ****. After you enter the last digit, a confirmation screen appears. Enter the password again. You see the message Password accepted. Numeric buttons 5. After you finish setting the password, press the Esc button to return to the Password Protect menu.
Starting the Projector with a Password When the password function is enabled, you see this screen when you turn on the projector: Use the numeric buttons on the remote control to enter the password. Once you have entered the password correctly, the password screen closes, and projection begins. If the password is not correct, you see the message Wrong password. Please try again. If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked.
Disabling the Projector’s Buttons You can use the Operation Lock function to disable all the projector’s buttons, or all the buttons except for the P Power button. note To cancel Operation Lock, press the projector’s Enter button for 7 seconds. 1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Use the up and down arrow buttons to select Operation Lock and press the Enter button. 4.
Restoring the Default Settings note The Computer Input (1 and 2), User’s Logo, Lamp Hours, and Language settings do not return to their defaults when you select Reset All. To reset the computer inputs, use the Reset option on the Signal menu; see page 54 for details. To reset the Language settings, use the Reset option on the Extended menu; see page 58 for details. The Reset menu lets you return most projector menu settings to their default values.
5 Maintenance and Transportation Y warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this User’s Guide. Refer all other servicing to qualified service personnel. our projector needs little maintenance.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. caution Do not use glass cleaner to clean the lens. To remove dirt or smears on the lens, use a commercially available cloth for cleaning glasses. Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord. ■ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth. ■ To remove stubborn dirt or stains, moisten a soft cloth with water and a mild detergent.
To clean the air filter and air vent, follow these steps: 1. Turn off the projector, allow it to cool down, and unplug the power cord. 2. To clean the filter and vent, Epson recommends using a small vacuum cleaner designed for computers and other office equipment. If you don’t have one, gently clean them using a very soft brush (such as an artist’s paintbrush). You can remove the air filter to clean both sides. Vent Air filter If the dirt is difficult to remove or if the filter is torn, replace it.
4. Align the new filter and slide it in until it clicks into place. note Air filters contain polycarbonate, ABS resin, and polyurethane foam. Dispose of used air filters according to local regulations. Replacing the Lamp note You can check to see how many hours the lamp has been used. See page 60. Turn off this product when not in use to prolong the life of the projector. The projection lamp typically lasts for about 3000 hours of use (in high brightness mode) or 4000 hours (in low brightness mode).
3. Use the screwdriver included with the replacement lamp or a #2 Phillips-head screwdriver to loosen the screw holding the lamp cover (the lamp cover is located on top of the projector). 4. Slide the cover out, then lift it off. 5. Use the screwdriver to loosen the two screws holding the lamp in place. (You can’t remove the screws.) 6. Hold the lamp as shown and pull it straight out. Don’t remove these screws note The lamp(s) in this product contain mercury.
caution Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. note Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on. 7. Gently insert the new lamp along the guide rail. If it doesn’t fit easily, make sure it’s facing the correct way. Push the lamp down firmly where the label PUSH appears. 8. Once the lamp is fully inserted, tighten its screws. 9.
Resetting the Lamp Timer note You must reset the lamp timer after replacing the lamp to clear the Replace the Lamp warning message. Follow these steps: 1. Connect the power cable and turn on the projector. 2. Press the Menu button on the remote control or projector and select the Reset menu. Then press Enter. Do not reset the lamp timer if you have not replaced the lamp. If you do, the Lamp Hours will not accurately reflect the number of hours that the lamp has been used. 3.
Transporting the Projector The projector contains many glass and precision parts. If you need to transport it, please follow these packing guidelines to prevent damage to the projector: ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
6 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on the projector or remote control. 1. Press the ? Help button on the remote control or projector. You see the Help menu. 2. Use the up and down arrow buttons on the projector or remote control to highlight the problem you want to solve. Then press the Enter button to view the solution(s). 3. Press Esc to view another topic or press ? Help to exit.
Power light Lamp light Temperature light Description Green Off Off The projector is operating normally. Flashing green Off Off The projector is warming up. Wait for the image to appear. Orange Off Off The projector is in standby or sleep mode. You can unplug it or press the P Power button to turn it on. Flashing orange Off Off The projector is shutting down. Wait for the light to stop flashing and remain orange before unplugging it. Red Off Flashing orange The projector is too hot.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the P Power light is green, not flashing, and the A/V Mute slide is open. Also press the A/V Mute button on the remote control to see if the picture was turned off temporarily. ■ If the projector doesn’t turn on, the Operation Lock may be enabled. Press and hold the Enter button on the projector for 7 seconds to release the lock. ■ The projector may be in standby or sleep mode.
Nothing appears on the external monitor. ■ Make sure the VGA computer cable is connected to your computer’s video port and the projector’s Computer1 port. ■ Make sure the cable from your monitor is connected to the projector’s Monitor Out port. You see a blue screen with the message No Signal displayed. ■ Make sure the cables are connected correctly, as described in Chapter 1. ■ Make sure the power to your computer or video source is turned on.
Only part of the computer image is displayed. ■ If you’re projecting from a computer or RGB video device, press the Enter/Auto button on the remote control. If this doesn’t work, you may need to adjust the Position setting in the Signal menu. See page 55 for more information. ■ If you’ve enlarged part of the image using the E-Zoom button on the remote control, press the Esc button to cancel zooming and return to full display.
The image contains static or noise. ■ If you’re using a computer cable longer than 6 feet (2 meters), or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables separated from the power cord as much as possible to prevent interference. ■ The video signal may be split between the computer and the projector.
You see vertical stripes or the image still looks blurry after trying the solutions in the previous section. ■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice one or more vertical stripes or bands, or some of the characters may look heavy or blurred. Press the Enter/Auto button on the remote control to automatically reset the projector’s tracking and sync settings.
There is no sound. ■ Press the button on the projector or the Vol+ button on the remote control to turn up the volume. ■ If you’ve turned off the picture and sound, press the A/V Mute button on the remote control to turn them on again. ■ If you’re using a DVD player or other video source, or external speakers, make sure their volume is not turned all the way down or muted. Also, make sure the cables are connected correctly, as described in Chapter 1.
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. ■ Make sure you are within 20 feet of the projector, and within range of the projector’s front or back sensor (approximately 30° to the left or right and 15° above or below). ■ If a button on the remote control is held for more than 30 seconds, the remote enter sleep mode. Press another button for normal operation. ■ The remote control batteries may not be installed correctly or may be low on power.
Where To Get Help Epson provides these technical support services: Internet Support Visit Epson’s support website for solutions to common problems with the PowerLite 83V+. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions. Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card.
Purchase Supplies and Accessories You can purchase screens, carrying cases, or other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
A Technical Specifications General Type of display Poly-silicon TFT active matrix Lens F=1.6 to 1.74, 18.4 to 22.12 mm Resolution 1024 × 768 pixels (XGA) Color reproduction Full color, 16.77 million colors Light output (brightness) High brightness mode White light output 2200 lumens (ISO 21118 standard) Color light output 2200 lumens Low brightness mode White light output 1760 lumens (ISO 21118 standard) Contrast ratio 400:1 Image size 30 to 300 inches (0.8 to 7.
Noise level note Lamp life will vary depending upon mode selected, environmental conditions and usage. Brightness decreases over time. Keystone correction angle 35 dB (High brightness mode) 28 dB (Low brightness mode) ± 30° vertical (maximum) Projection Lamp Power consumption 170 W UHE Lamp life About 3000 hours (High brightness); 4000 hours (Low brightness) Remote Control Range 20 feet (6 meters) Batteries (2) Alkaline AA Dimensions Height (including feet) 4.3 inches (108 mm) Width 12.
Environmental Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Altitude Up to 4,900 feet (1,500 m) Up to 7,500 feet (2,286 m) with High Altitude Mode enabled; see page 58 Safety and Approvals United States FCC Part15B Class B (DoC) UL60950-1 Canada ICES-003 Class B CSA C22.2 No. 60950-1 Pixelworks™ DNX™ ICs are used in this projector.
Compatible Video Formats You can use any of the following video sources: VCR, DVD player, camcorder, digital camera, or gaming console. The projector supports composite video, S-Video, component video, and RGB video, and it automatically senses the video format (HDTV, SDTV, NTSC, PAL, or SECAM).
Compatible Computer Display Formats You can connect the projector to a wide range of computers, including PCs and notebooks, Apple Macintosh, PowerPC and Intel Core Macintosh computers, PowerBook computers, many iMac and iBook series systems, and high-end workstations such as the Sun® SPARCstation.™ Although images are displayed at the projector’s native resolution of 1024 × 768 pixels, Epson’s patented SizeWise chip supports computer display formats ranging from VGA through UXGA.
The projector supports these monitor display formats: 94 Technical Specifications Mode Refresh Rate (Hz) Resolution VGA EGA 70 640 × 350 VGA—60 VESA—72 VESA—75 VESA—85 VGA—120 60 72 75 85 120 640 × 480 640 × 480 640 × 480 640 × 480 640 × 480 SVGA—56 SVGA—60 SVGA—72 SVGA—75 SVGA—85 SVGA—120 56 60 72 75 85 120 800 × 600 800 × 600 800 × 600 800 × 600 800 × 600 800 × 600 XGA—60 XGA—70 XGA—75 XGA—85 XGA—120 60 70 75 85 120 1024 × 768 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA1—70 SXGA1—75
Mode Refresh Rate (Hz) Resolution iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19—60 MAC19 MAC21 117 95 75 67 75 59 75 75 640 × 480 800 × 600 1024 × 768 640 × 480 832 × 624 1024 × 768 1024 × 768 1152 × 870 SDTV 480i SDTV (576i) SDTV (480p) SDTV (576p) 60 50 60 50 720 × 480 720 × 576 720 × 480 720 × 576 HDTV (720p) HDTV (1080i) 50/60 50/60 1280 × 720 1920 × 1080 Technical Specifications 95
Technical Specifications
B Notices This chapter includes safety instructions and other important information about your PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.
■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards. ■ Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled into the projector, or if it has been exposed to rain or water.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Notices
Index A A/V cable, 24 to 25 A/V Mute, 46, 59, 63 to 64, 80, 85 Accessories, 13, 88 Air filter cleaning and replacing, 70 to 72 purchasing, 13 Altitude, 59, 91 Anti-theft device, 13 Aspect button, 47 Aspect ratio, 47, 56, 89 Aspect setting, 56 Audio adjusting volume, 41, 57 cable, 22, 85 connecting laptop, 22 problems, troubleshooting, 85 turning off, 46 Auto button, 41, 55 Auto Keystone correction, 17, 40, 50, 57 Auto Setup setting, 41, 55 B Background Color setting, 59, 65 Banding in image, 84 Batteries,
Direct Power On setting, 59 Distance from projector to screen, 16, 89 Documentation, using, 9 DVD player, connecting to, 24 to 31 E Entering the password, 66 Environmental specifications, 91 Epson accessories, 13, 88 PrivateLine Support, 9, 87 Store, 88 technical support, 9, 87 warranty, 10 Extended menu, 50, 58 to 59 External monitor, connecting, 21 E-Zoom button, 47 F FCC compliance statement, 99 Filter, cleaning and replacing, 70 to 72 Focusing, 38 Foot release lever, 39 Freeze button, 46 Front project
Lens cleaning, 70 specifications, 89 Lights, status, 78 to 79 Logo creating, 63 to 64 displaying, 64 to 65 turning on, 59, 65 Low brightness, 40, 72, 89 M Macintosh connecting, 18 to 20 Macintosh display problems, 37 Manuals, 9 Menus changing settings, 51 to 52 Extended, 50, 58 to 59 Image, 50, 52 to 54 Info, 50, 60 to 61 Reset, 50, 68 Settings, 50, 56 to 57 Signal, 50, 54 to 56 User’s Logo, 63 to 64 using, 50 to 52 Messages setting, 58 Monitor, external, 21 Moving projector, 76 N No Signal message, 36 to
Projector accessories, 13, 88 carrying case, optional, 76 cleaning, 69 to 72 disabling buttons, 57, 67 distance from screen, 16, 89 foot, adjusting height with, 39 lamp specifications, 90 password protection, 61 to 66 positioning, 16 to 17 resolution, 7, 89, 93 to 95 transporting, 76 turning off, 42 turning on, 34 to 35 unpacking, 10 viewing information about, 60 to 61 Q Quick Setup sheet, 9 R Raising image, 39 RCA A/V cable, 24 to 25 Rear projection, 17, 59 Registration, 10 Remote control problems, 86 re
Tracking, adjusting, 55, 83 to 84 Transporting projector, 76 Troubleshooting color, 84 cut-off image, 41, 82 image quality, 83 to 84 image shape, 82 no image, 80 to 81 no signal, 36 to 37 no sound, 85 password, 85 remote control problems, 86 Turning off audio, 46 picture, 46 projector, 42 Turning on password, 65 projector, 34 to 35 User’s Logo, 59, 65 Typing the password, 66 Warranty, 10, 10 Weight, 90 Z Zoom ratio, 89 Zooming image, 47 U Unpacking projector, 10 User’s Logo creating, 63 to 64 displaying,
