Epson PowerLite 61p/81p Multimedia Projector ® ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 8 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 9 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 9 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Additional Components . . . . . . .
2 Projecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 3 Using the Remote Control . . . . . . . . . . . . . . . . . . . 43 4 4 Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 30 Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 30 Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 32 What To Do If You See a Blank Screen . . . . . . . . . . . . . 33 Adjusting the Image . . . . . . . . . . . . . . . . . .
Using the Projector’s Security Features. . . . . . . . . . . . . . . . . Creating Your Own Screen Logo. . . . . . . . . . . . . . . . . . Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . Turning On the Password and User’s Logo . . . . . . . . . . Starting the Projector with a Password. . . . . . . . . . . . . . Disabling the Projector’s Buttons . . . . . . . . . . . . . . . . . Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . . . .
Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . . 98 Compatible Computer Display Formats. . . . . . . . . . . . . . . . 99 8 Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 101 Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . 103 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . 104 FCC Compliance Statement. . . . . .
- Welcome The Epson ® PowerLite® 61p and 81p are ultra-portable projectors that offer up to 2000 ANSI lumens of brightness. From classrooms to auditoriums, your full-color presentations and videos will be bright and visible even in ordinary indoor lighting. Additionally, the projector’s built-in amplifier and speaker deliver powerful 5 watt audio, making it perfect for presentations in large rooms.
To prevent unauthorized use of the projector, you can assign a password, create a user logo which is displayed at startup to identify the projector, and disable the projector’s buttons through the Operation Lock feature. For more information about security features, see page 62.
Using Your Documentation Your documentation includes a Quick Setup sheet, warranty brochures, and Epson PrivateLine® Support card. The Quick Setup sheet gives instructions to quickly set up your projector and connect it to a laptop or PowerBook computer. This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury.
Registration and Warranty Your projector comes with a basic carry-in warranty and an international warranty that let you project with confidence anywhere in the world. For details, see page 106 and the warranty brochure that came with your projector. In addition, Epson offers free Extra CareSM Road Service. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired.
Save all packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when you need to send the projector to another location. If you are moving the projector by hand, use the carrying case included with the projector. Additional Components Depending on how you plan to use the projector, you may need additional components: ■ To receive an S-video signal, you need an S-video cable. One is usually provided with your video device, or you can purchase it from Epson.
Optional Accessories note To purchase a replacement remote control, call (562) 276-4394 (U.S.) or (905) 709-3839 (for dealer referral in Canada).
1 Setting Up the Projector T his chapter tells you how to set up the projector and connect it to a computer or video source. You can connect up to four devices simultaneously: four video sources, one computer and three video sources, or two computers and two video sources.
Positioning the Projector Before connecting the projector, you need to decide where to place it. If you’re setting up the projector yourself and it isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it. Try to leave as much space as possible between the projector and the screen to get a good-size image.
Try to place the projector directly in front of the center of the screen, facing it toward the screen squarely. If the projector isn’t positioned this way, the image will be “keystone” shaped, instead of square or rectangular. If you place the projector below the level of the screen, you’ll have to tilt it up by extending the front adjustable foot, as described on page 37. This also causes the image to lose its rectangular shape, but the Auto Keystone feature corrects the distortion automatically.
Connecting to a Computer note If you have an iBook with an RCA video-out port, follow the instructions for connecting to a video device on page 23. You can connect the PowerLite projector to any computer that has a standard VGA or BNC monitor port, including PC notebook and laptop computers, Macintosh PowerBooks and iBooks, and hand-held devices. You can connect two computers at the same time.
3. Connect one end of the cable to the projector’s Computer1/Component Video1 or the Computer2/Component Video2 port. If you are going to connect your computer monitor to the projector for simultaneous display, use the Computer1/Component Video1 port. 4. Connect the other end of the cable to your computer’s video-out or monitor port. If you’re using a PowerBook or iBook and you can’t connect the cable, you may need to use the Macintosh desktop adapter as shown below (available from Epson; see page 12).
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 30 for instructions. If more than one device is connected to the projector, select the correct source after projection starts by pressing the Source Search button on the projector or the Comp1 or Comp2 button on the remote control. See page 32.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 30 for instructions. If more than one device is connected to the projector, select the correct source after projection starts by pressing the Source Search button on the projector or the Comp1 or Comp2 button on the remote control. See page 32.
3. Connect the flat end of the cable to an available USB port on your computer. 4. If necessary, configure your laptop to work with an external mouse. If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 30 for instructions. Connecting an External Monitor note Some LCD monitors may not be able to display the image correctly. If you have trouble displaying the image, connect a multiscan monitor.
Playing Sound Through the Projector Your computer probably has its own sound system; however, it may not be adequate for your presentation. If you need more volume, you can connect a computer audio cable to take advantage of the projector’s built-in amplifier and speaker. You can obtain a computer audio cable (3.5-mm stereo miniplug cable) from a computer or electronics dealer. 1. Connect one end of the audio cable to the Audio1 jack on the projector.
Connecting to Video Sources You can connect a DVD player, VCR, camcorder, laser disc player, digital camera, gaming console—such as Microsoft Xbox, Sony PlayStation 2, or Nintendo GameCube—or any other compatible video source to your projector. You can connect up to four video devices at one time. note The projector does not support TV antenna cable F connectors. The projector supports HDTV, SDTV, NTSC, PAL, and SECAM, and automatically detects the video format.
Connecting a Composite Video Source If you’re connecting a composite video device, use a commercially-available RCA A/V cable. Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Connect the yellow RCA plug on one end of the cable to the projector’s yellow Video jack as shown below. 2. Connect the yellow plug on the other end of the cable to the video-out port on your video source. 3.
Connecting an S-video Source If your video source has an S-video jack, you can use it to project a higher quality video image. You’ll need an S-video cable (ELPSV01), which is usually provided with your video source, or you can purchase one from Epson. See page 12 for ordering information. Before starting, make sure the projector and your DVD player or other video source are turned off. 1.
Connecting an RGB Video Source Follow these instructions to connect the projector to a video player or satellite receiver that has an RGB video output port using the VGA computer cable that came with the projector. Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Connect one end of the VGA computer cable to the Computer1/Component Video1 or the Computer2/Component Video2 port on the projector. 2. Connect the other end to the video port on your player. 3.
Connecting a Component Video Source If your video source has component video connectors, you can use them to project a higher quality video image. You’ll need a component video cable (ELPKC19), which can be purchased from Epson. See page 12 for ordering information. Before starting, make sure the projector and your DVD player or other video device are turned off. 1. Connect the large end of the component video cable to the projector’s Computer1/Component Video1 or the Computer2/Component Video2 port. 2.
Playing Sound Through the Projector The projector has a built-in speaker with a maximum output of 5 W. You can play sound from your video equipment through the projector’s speaker if your video device has an audio output port. For RCA-Style Audio Output Ports Most video devices have an RCA-style audio output port. In this case, use the audio adapter supplied with the projector to connect the projector to a commercially-available A/V cable, as shown below: Audio adapter 1.
For Stereo Mini-Jack Audio Output Ports Some video devices, especially camcorders, may have a stereo mini-jack audio output port. In this case, use a commercially-available stereo mini jack audio cable to connect to the projector, as shown below: note Each input port has its own dedicated audio output jack. To play sound from a source, you must connect the audio cable to the correct audio output jack. When you switch the video source, the projector automatically plays sound from the new source.
1 Projecting Once you’ve set up the projector, you’re ready to turn it on, adjust the image, and give your presentation. Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote.
Turning On Your Equipment Make sure your projector and other equipment are set up and connected correctly, as described in Chapter 1. Then turn on your projector, as described below. If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image source manually. See page 32.
3. Connect the other end to an electrical outlet. The power light on top of the projector turns orange, indicating that the projector is receiving power but not yet turned on. Wait until the light stops flashing but stays orange. 4. Turn on your computer or video source if you have not already. 5. Press the P Power button on top of the projector to turn it on. (You can also press the P Power button on the remote control.
To focus and adjust the image, see page 35. If a projected image fails to appear, see “What To Do If You See a Blank Screen” on page 33. When you’re done with your presentation, shut down the projector as described on page 41. Shutting down the projector correctly prevents premature lamp failure and possible damage from overheating. Selecting the Image Source note The name of the selected image source appears in the upper right corner of the screen.
What To Do If You See a Blank Screen If you see a blank screen or a blue screen with the message No Signal after turning on your computer or video source, try the following: ■ Make sure the cables are connected correctly, as described in Chapter 1. ■ Make sure the power light is green and not flashing and the lens cap is off. ■ Make sure you’ve selected the correct image source; see page 32. Allow a few seconds for the projector to sync up after pressing the button.
If you’re using a Macintosh laptop with OS X: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select System Preferences, then click Displays. 2. Select VGA Display or Color LCD, click Arrange or Arrangement, and make sure Mirror Displays is checked. Click here Select Mirror Displays If you’re using a Macintosh laptop with OS 9.
3. Drag one monitor icon on top of the other. If the Arrange option isn’t available, you may need to select one of the Simulscan resolution settings: 1. Click the Monitor icon, if necessary. Click here Select a Simulscan resolution 2. Select a Simulscan resolution, as shown. (Allow a few seconds for the projector to sync up after making the selection.) Adjusting the Image Once you see your image, you’ll need to make certain adjustments: ■ To focus or zoom your image, see the next section.
Focusing and Zooming Your Image Rotate the focus ring to sharpen the image. Focus ring Rotate the zoom ring to reduce or enlarge the image. Zoom ring You can also change the image size by moving the projector closer to or farther away from the screen. You can use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 45 for instructions.
Adjusting the Height of Your Image If the image is too low, you can raise it by extending the projector’s front adjustable foot. 1. Stand behind the projector. Press up on the blue foot release lever and lift the front of the projector to extend the front adjustable foot. Foot 2. Once the image is positioned where you want, release the lever to lock the foot in position. 3. To fine-tune the height of the image, rotate the feet at the back of the projector.
Adjusting the Image Shape Pointer button Enter button The projector automatically corrects images that are distorted when the projector is tilted up or down (up to a 15° tilt). The Keystone window appears on the screen while the projector makes the correction. If the projected image still isn’t rectangular or has a “keystone” shape, do one or more of the following: ■ If your image looks like or , you’ve placed the projector off to one side of the screen, at an angle.
You can also make keystone adjustments using the projector’s Setting menu. See page 58. Adjusting the Brightness The brightness of an image depends on the source you are projecting and the amount of light in the room. If the image is too bright or not bright enough, here are two ways you can adjust it: ■ Change the Brightness setting in the Image menu. See page 54. ■ Select Low or High for the Brightness Control option in the Setting menu. (See page 58.
The following table lists the six color modes available. Color mode Description sRGB Use when projecting computer images conforming to the sRGB color standard (the default setting when projecting from a computer with analog video). Dynamic Best for projecting movies with vivid color in bright rooms. Presentation Use when you’re projecting a presentation in a bright room. Theatre Use when projecting movies in a dark room. Living Room Best for playing video games or watching TV in a bright room.
Adjusting the Volume You can use the buttons on the remote control or projector to increase or decrease the volume for both the projector’s built-in speaker and external speakers connected to the projector. Press the button to increase the volume, or the button to decrease it. A volume gauge appears on the screen while the volume is being adjusted. Volume controls Shutting Down the Projector When you’ve finished using the projector, follow the recommended procedure to shut it down.
3. Press the P Power button again. The projector beeps twice, the lamp is turned off, and the power light flashes orange for about 60 seconds as the projector cools down. When the projector has cooled, the light stays orange and the exhaust fan shuts off. If you want to turn the projector on again, wait until the orange light stops flashing. Then press the P Power button. 4. Press up on the blue foot release lever and lower the projector to retract the front adjustable foot, as shown.
13 Using the Remote Control T he remote control lets you access your projector’s features from anywhere in the room—up to 20 feet away. For example, you can turn the projector on and off, freeze the presentation, zoom in on a portion of your image, and access the menu system. (The projector menus let you adjust many projector settings; see Chapter 4.) If you’re using a computer and you’ve connected the mouse cable as described in Chapter 1, you can use the remote control as a wireless mouse.
Controlling the Picture and Sound You can use the remote control to select your source, temporarily turn off the picture and sound, freeze the action, or zoom in on the picture. Make sure you have set up your projector and connected any equipment as described in Chapter 1.
Turning Off the Picture and Sound Press the A/V Mute button on the remote control to turn off the image and sound and darken your screen. This is useful if you want to temporarily re-direct your audience’s attention without the distraction of a bright screen. ■ To turn off the picture and sound, press the A/V Mute button. The screen goes dark. ■ To turn the image and sound back on, press the button again, or press Esc.
4. While the image is enlarged, you can: ■ Use the pointer button to pan about. ■ Press the E-Zoom button to zoom out. 5. When you’re done, press the ESC button to return to the original size. note You must be projecting component, composite, or S-video images to change the aspect ratio. You can also change the aspect ratio using the projector’s Signal menu. See page 55 for details.
Using the Remote Control as a Wireless Mouse When you use the remote control as a wireless mouse, you can control your computer or click through slideshow-style presentations (such as PowerPoint) from up to 20 feet away. This gives you more flexibility, since you don’t need to stand near your computer to change slides. Left-click or double-click Move the pointer Display the pointer Right-click To control your computer with the remote, make sure you have connected the USB cable as described on page 19.
Replacing the Batteries note The remote control automatically shuts off when it detects a button being pressed more than 30 seconds. This conserves battery life. It can be helpful, for example, when the remote is in a carrying case and the P Power button is accidentally pushed. The remote control uses two AAA alkaline batteries. Follow these steps when you need to replace them: 1. Press in the tab to remove the battery cover. 2. Remove the old batteries, then insert the new ones as shown.
433 Fine-tuning the Projector You can use the Menu button on the projector or remote control to access on-screen menus to adjust the image, sound, and other features.
Using the Projector’s Menu System The six projector menus let you adjust and customize the projector features: 50 ■ The Image menu lets you modify the colors of the projected image and fine-tune brightness, contrast, and sharpness. ■ The Signal menu lets you make adjustments to the input signal. You can select your input source, change the image position and aspect ratio, and adjust tracking and sync for computer images. ■ The Setting menu lets you customize the way you use the projector.
Changing Menu Settings Use the buttons on the remote control to access the menus and change settings. Follow these steps: 1. Press the Menu button on the remote control or projector to display the menu screen: Menu button Esc button Menu options Menus Enter button Arrow buttons Pointer button The six menus are listed on the left, and the options available for the highlighted menu are shown on the right. 2.
4. After highlighting the option you want to adjust, use the pointer button on the remote control or left or right arrow buttons on the projector to change the setting. In some cases, you may have to press the Enter button to see a sub-screen for changing the setting. ■ Press the left or right side of the pointer button or the left or right arrow buttons on the projector to adjust a slider bar.
Adjusting Colors and Clarity The Image menu lets you make adjustments to the colors of the projected image and fine-tune brightness, contrast, and sharpness. The options available depend on which image source is selected: Computer (analog-RGB) and RGB video Component, composite, and S-video Follow these steps to adjust the appearance of your image: 1. Press the Menu button. You see the main menu. 2. Press Enter to select the Image menu.
3. Use the pointer button (or the up and down arrow buttons) and press Enter to select any of the following options: ■ Color Mode Corrects the vividness of image color. You can select from the following six settings, and save a different one for each computer and/or video source: Dynamic: For projecting movies or playing video games in vivid color in a bright room. Presentation: For presentations in bright rooms.
Adjusting the Input Signal Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to make manual adjustments. In addition to changing the position of the projected image, you can correct tracking and sync for computer images, or change the aspect ratio to widescreen format for video images. 1. Press the Menu button. You see the Image menu. 2. Select the Signal menu.
3. Press Enter. Then use the pointer button (or up and down arrow buttons) and the Enter button to select any of the following options: ■ Auto Setup (computer images) Leave this setting ON to automatically optimize the computer image. Turn it off if you want to save adjustments you have made to the video settings. ■ Tracking (computer images) Removes unwanted vertical lines from a computer image by matching the projector’s internal clock to various computer signals.
■ Video Signal (composite and S-video) Leave this setting at Auto unless you are using a 60-Hz PAL system (select PAL60). ■ Resize (video) Sets the image’s aspect ratio (ratio of width to height) to 4:3 for letterbox video content and to 16:9 for widescreen video content. 4. When you’re finished adjusting the signal settings, press Esc or Menu.
3. Press Enter. Then use the pointer button (or up and down arrow buttons) and the Enter button to set the following options: ■ Keystone Adjusts a distorted image from a trapezoid shape to rectangular. ■ Auto Keystone Automatically adjusts a distorted image from a trapezoid shape to rectangular when the projector’s foot is extended or retracted. (Not available when you’re projecting from the ceiling or using rear projection.) Select ON or OFF.
Selecting Projector Setup Options Use the Extended menu to customize the way you set up the projector. You can configure the projector for rear and/or ceiling projection, change the language for the menus and messages, set the screen background color, capture and store a custom image or logo for the startup screen, and set up the projector for network use. 1. Press the Menu button. 2. Select the Extended menu. You see the features and their settings on the right side: 3. Press Enter.
■ Projection Front: Projector is in front of the screen. Front/Ceiling: Projector is in front of the screen, mounted upside-down from the ceiling. Rear: Projector is behind the screen. Rear/Ceiling: Projector is behind the screen, mounted upside-down from the ceiling. note ■ When Direct Power is turned on, press the P Power button to turn the projector off, wait until the P power light turns a steady orange, then unplug the power cord.
Viewing Lamp Usage and Other Information note You can make changes to many of the signal settings on the Signal menu. See page 55 for details. Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used. 1. Press the Menu button and select the Info menu.
■ Refresh Rate (computer, RGB video, and component video) Displays the refresh rate. ■ Sync Info (computer, RGB video, and component video) Provides information that may be needed by the service technician. 2. When you’re finished, press Esc or Menu.
If you assign the projector a password, a screen appears requesting the password whenever the projector is turned on. If you enter the password incorrectly three times in succession, the projector’s operation is locked and you’ll need to disconnect the power cord, then reconnect it to redisplay the password screen. If an incorrect password is entered 30 times in a row, the projector is locked and you’ll need to contact Epson to unlock it. See “Where To Get Help” on page 92.
3. Use the pointer button (or the down arrow button) and press Enter to select User’s Logo. 4. When you see a message asking if you want to use the present image as a user’s logo, select Yes and press Enter. A selection box displays over the image. 5. Use the pointer button on the remote control or the arrow buttons on the projector to select the area of the image you want to use. Once you have selected the area, press Enter. 6. When you see the message Select this image?, choose Yes and press Enter.
Setting a Password 1. Press the Freeze button on the remote control for about 7 seconds until you see the Password Protect menu: note If a password has already been set, you see the Password Protect Release screen. See “Starting the Projector with a Password” on page 66. 2. Select Password and press Enter. You see the message Change the password? 3. Select Yes and press Enter. 4. Hold down the Num key on the remote control and use the numeric keypad to enter a 4-digit password.
The countdown for the elapsed time begins as soon as you close the Password Protect menu. (You can check the elapsed time in this menu next to Time elapsed.) 3. To enable your screen logo, select User’s Logo Protect and press Enter. Select ON and press Enter. When this feature is on the logo appears whenever the projector is turned on (if the Startup Screen is enabled in the Extended menu; see page 59) and as the A/V Mute screen (if you selected the Logo as the Background Color in the Extended menu).
If the password is not correct, you see the message Wrong password. Please try again. If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked. Request code xxxxx and the projector switches to standby mode for approximately 5 minutes. Write down the request code. Then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.
Restoring the Default Settings note The input signal, Video Signal, User’s Logo, and Language settings do not return to their defaults when you select All Reset. To reset the input signal or video signal, use the Reset option on the Signal menu; see page 55 for details. To reset the User’s Logo and Language settings, use the Reset option on the Extended menu; see page 59 for details. The Reset menu lets you return most projector menu settings to their default values.
5 Maintaining and Transporting the Projector Y warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this User’s Guide. Refer all other servicing to qualified service personnel. our projector needs little maintenance.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. caution ■ Use a canister of compressed air to remove dust. ■ To remove dirt or smears on the lens, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface. Do not use glass cleaner to clean the lens. Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord.
Cleaning and Replacing the Air Filter Clean the air filter and air intake and exhaust vents on the bottom and rear of the projector after every 100 hours of use. If they are not cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. When the filter and vents are clogged, the projector displays the message The projector is overheated. To clean the air filter and air vents, follow these steps: 1.
4. If you need to replace the filter, slide it off, as shown. 5. Align the new filter carefully as you slide it into place. It should click into place.
Replacing the Lamp The projection lamp typically lasts for about 2000 hours of use (in high brightness mode) or 3000 hours (in low brightness mode). It is time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate. ■ The ■ The message Replace the Lamp appears on the screen when the lamp comes on. To maintain projector brightness and image quality, replace the lamp as soon as possible. lamp light is flashing orange.
5. Use the screwdriver to loosen the two screws holding the lamp in place. (You can’t remove the screws.) Don’t remove these screws warning 6. Hold the lamp as shown and pull it straight out. This product includes a lamp component that contains mercury (Hg). Please consult your state and local regulations regarding disposal or recycling. Do not put it in the trash. caution 7. Gently insert the new lamp. If it doesn’t fit easily, make sure it’s facing the correct way.
8. Once the lamp is fully inserted, tighten its screws. note Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on. 9. Lower the lamp cover into place. (The opening should be almost covered, and the top of the cover should be flush with the top of the projector.) Then slide the cover closed and tighten the screws. 10. Reset the lamp timer as described in the next section.
Resetting the Lamp Timer note Do not reset the lamp timer if you have not replaced the lamp. If you do, the Lamp Hours will not accurately reflect the number of hours that the lamp has been used. You must reset the lamp timer after replacing the lamp to clear the Replace the Lamp warning message. Follow these steps: 1. Connect the power cable and turn on the projector. 2. Press the Menu button on the remote control or projector and select the Reset menu. Then press Enter.
Transporting the Projector The projector contains many glass and precision parts. If you need to transport it, please follow these packing guidelines to prevent damage to the projector: ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
Maintaining and Transporting the Projector
6 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ? Help button on the projector or remote control. The following choices are available: Use to select a problem or solution Press to return to the last menu ■ No signal or image appears on the screen ■ Problems with sound ■ Language change Follow these steps to get help: 1. Press the ? Help button on the remote control or projector. You see the help menu.
4. Highlight a solution (if this choice is available). Then press the Enter button to select the solution. Press the Esc button if you need to back up. If the solution is to adjust one of the settings, use the pointer button on the remote control or the left and right arrow buttons on the projector to adjust it. 5. To exit the Help system, press the ? Help button. If none of the suggestions solves your problem, see additional solutions to problems in the following sections.
Power light Lamp light Temperature light Red Flashing red Flashing red There is an internal error in the projector. Turn the projector off and unplug it. Contact Epson for help. Red Off Flashing red There is a problem with the fan or a sensor. Turn the projector off and unplug it. Contact Epson for help. Red Flashing red Off The lamp is burned out, broken, or not installed correctly; or the lamp cover is open.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the power light is green, not flashing, and the lens cap is off. ■ The projector may be in standby or sleep mode. If the projector has not received any input signal for 30 minutes, it turns off the lamp to conserve the lamp life and save energy. If the power light is orange, press the P Power button to turn the projector on. ■ Press the A/V Mute button to make sure the picture has not been turned off temporarily.
Nothing appears on the external monitor. ■ Make sure the VGA computer cable is connected to your computer’s video port and the projector’s Computer1/Component Video1 port. It will not work if you connected the computer cable to the projector’s Computer2/Component Video2 port. ■ Make sure the cable from your monitor is connected to the projector’s Monitor Out port. You see a blue screen with the message No Signal displayed. ■ Make sure the cables are connected correctly, as described in Chapter 1.
■ Depending on your computer’s video card, you might need to use the Display utility in the Control Panel to make sure that both the LCD screen and external monitor port are enabled. See your computer’s documentation or online help for details. If you’re using a PowerBook or iBook with Macintosh OS X: 1. From the Apple menu, select System Preferences, then click Display. 2. Select VGA Display or Color LCD, click Arrange or Arrangement, then put a check mark in Mirror Displays.
Only part of the computer image is displayed. ■ If you’re projecting from a computer or RGB video device, press the Auto button on the remote control. If this doesn’t work or if you’re projecting from a component, composite, or S-video device, you may need to adjust the Position setting in the Signal menu. See page 56 for more information. ■ If you’ve enlarged part of the image using the E-Zoom button on the remote control, press the Esc button to cancel zooming and return to full display.
The image isn’t rectangular, but trapezoid-shaped. ■ Make sure the projector isn’t placed off to one side of the screen, at an angle, or the image won’t be rectangular. Place it directly in front of the center of the screen, facing the screen squarely. ■ If you’ve tilted the projector upward, the image will be broader at the top. Turn on Auto Keystone correction as described on page 57 or hold down the or buttons on top of the projector until the image is rectangular. The image contains static or noise.
The image is blurry. ■ Adjust the focus using the focus ring. ■ Make sure the lens cap is off. ■ There may be dirt or smears on the lens. Clean the lens as described on page 70. ■ Make sure the lens is not fogged by condensation. You may need to wait before using the projector after moving it from a cold environment. ■ Make sure the projection distance is within the range described on page 14. ■ Adjust the Sharpness setting on the Image menu (see page 54).
The colors of the image are not right. ■ Try selecting a different Color Mode. See page 54 for instructions. ■ If you’re displaying video, adjust the Color Intensity and Tint settings on the Image menu. See page 54 for instructions. ■ Adjust the Brightness and Contrast settings on the Image menu. See page 54. ■ Try adjusting the Color Adjustment setting on the Image menu. See page 54. ■ Make sure the input signal setting on the Signal menu matches the signal from the connected device.
■ Make sure the audio cable is connected to the correct Audio port. See page 21. ■ If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted. Make sure the audio cable is securely connected to both the projector and your computer’s headphone jack or audio out jack. See page 21. ■ The wrong source may be selected.
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. ■ Make sure you are within 20 feet of the projector, and within range of the projector’s front or back sensor (approximately 30° to the left or right and 15° above or below). ■ The remote control batteries may not be installed correctly or may be low on power. Replace the batteries as described on page 48. ■ Dim the room lights and turn off any fluorescent lights.
■ If you’re running Windows 98 or Me, you may need to install USB drivers from your Windows CD-ROM. After you install the drivers, restart both the computer and the projector to resynchronize the setup. Where To Get Help Epson provides technical assistance through electronic support services 24 hours a day, as listed in the following table. Service Access World Wide Web From the Internet, you can reach Epson’s product support page at http://support.epson.com.
Before you call, please have the following information ready: ■ Product name (Epson PowerLite 61p or PowerLite 81p) ■ Product serial number (located on the bottom of the projector) ■ Computer or video configuration ■ Description of the problem You can purchase screens, carrying cases, or other accessories from Epson at (800) 873-7766 or by visiting the Epson Store at www.epsonstore.com (U.S. sales only). In Canada, please call (800) 463-7766 for dealer referral.
Solving Problems
Technical Specifications General Type of display Poly-silicon TFT active matrix LCD panels (3) Diagonal size: 0.7 inches (17.8 mm) Lens F=1.70 to 1.87, f=21.3 to 25.6 mm Resolution 81p: 1024 × 768 pixels 61p: 800 × 600 pixels Color reproduction Full color, 16.8 million colors Brightness (ANSI) 2000 lumens (High brightness mode) 1500 lumens (Low brightness mode) Contrast ratio 400:1 Image size 30 to 300 inches (0.8 to 7.6 meters) Projection distance 2.9 to 35.5 feet (0.9 to 10.
note Lamp life results vary depending on environmental conditions and usage. Turn the projector off when not in use. Continuous 24-hour-a-day use may reduce the overall life of the product. Projection Lamp Power consumption 200 W Lamp life About 2000 hours (High brightness); 3000 hours (Low brightness) Remote Control Range 20 feet (6 meters) Batteries (2) Alkaline AAA Mouse Compatibility Supports USB Dimensions Height 4.3 to 4.8 inches (foot extended) (109 to 123 mm) Width 13.
Safety and Approvals United States FCC 47CFR Part15B Class B (DoC) UL60950 Third Edition Canada ICES-003 Class B CSA C22.2 No. 60950 (cUL) CE Marking Directive 73/23/EEC, 89/336/EEC IEC60950 Third Edition EN 55022, EN 55024 Pixelworks™ DNX™ ICs are used in this projector.
Compatible Video Formats You can use any of the following video sources: VCR, DVD player, camcorder, digital camera, gaming console, or laser disc player. The projector supports composite video, S-video, component video, and RGB video, and it automatically senses the video format (HDTV, SDTV, NTSC, PAL, or SECAM).
Compatible Computer Display Formats You can connect the projector to a wide range of computers, including PCs and notebooks, Apple Macintosh, Power Macintosh series (including G3, G4 and G5 systems), PowerBook computers, many iMac and iBook series systems, and high-end workstations such as the Sun® SPARCstation.
The projector supports these monitor display formats: 100 Technical Specifications Mode Refresh Rate (Hz) Resolution VGA EGA 70 640 × 480 VGA—60 VESA—60 VESA—72 VESA—75 VESA—85 60 60 72 75 85 640 × 480 640 × 480 640 × 480 640 × 480 640 × 480 SVGA—56 SVGA—60 SVGA—72 SVGA—75 SVGA—85 56 60 72 75 85 800 × 600 800 × 600 800 × 600 800 × 600 800 × 600 XGA—60 XGA—70 XGA—75 XGA—85 60 70 75 85 1024 × 768 1024 × 768 1024 × 768 1024 × 768 SXGA1—70 SXGA1—75 SXGA1—85 70 75 85 1152 × 864 1152 × 864 115
Notices This chapter includes safety instructions and other important information about your Epson PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.
■ Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector. ■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: ■ There is an object between the remote control IR emitter and the IR receiver on the projector. ■ Ambient light is too bright. ■ Certain types of fluorescent lighting are used. ■ A strong light source shines into the IR receiver.
Declaration of Conformity According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: Epson America, Inc. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Warranty Epson America, Inc. Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID.
Notices
Index A A/V cable, 22 to 23 A/V Mute, 45, 59, 63 to 64, 83, 89 Accessories, 12, 93 Adapters, Macintosh, 12, 17 Air filter cleaning and replacing, 71 to 72 purchasing, 12 Anti-theft device, 12 Aspect ratio, 46, 57, 95 Audio adjusting volume, 41, 58 cable, 8, 21, 90 connecting laptop, 21 problems, troubleshooting, 89 to 90 turning off, 45 Audio adapter, 10, 27 Auto button, 39, 56 Auto Keystone correction, 15, 38, 50, 58 Auto Setup setting, 39, 56 B Background Color setting, 59, 66 Banding in image, 88 Batter
Distance from projector to screen, 14, 95 Documentation, using, 9 DVD player, connecting to, 22 to 26 Dynamic color mode, 40 E Electrical specifications, 96 Enter button, 47, 51 to 52 Entering the password, 66 to 67 Environmental specifications, 96 Epson accessories, 12, 93 Extra Care Road Service, 10 PrivateLine Support, 9, 92 Store, 12, 93 technical support, 9, 92 to 93 Esc button, 47, 51 to 52 Extended menu, 50, 59 to 60 Extra Care Road Service, 10 E-Zoom button, 45 to 46 F FCC compliance statement, 10
Living Room color mode, 40, 54 Logo creating, 63 to 64 displaying, 64 to 66 turning on, 59, 65 to 66 Low brightness, 39, 73, 95 M Macintosh adapters, 12, 17 connecting, 16 to 19 Manuals, 9 Menus changing settings, 51 to 52 Extended, 50, 59 to 60 Image, 50, 53 to 54 Info, 50, 61 to 62 Reset, 50, 68 Setting, 50, 57 to 58 Signal, 50, 55 to 57 User’s Logo, 63 to 64 using, 50 to 52 Message setting, 59 Mouse compatibility, 96 connecting cable, 19 to 20 using remote control as, 47 Moving projector, 77 N Noise le
Projector accessories, 12 carrying case, 10 to 12, 77 cleaning, 69 to 72 disabling buttons, 58, 67 distance from screen, 14, 95 feet, adjusting height with, 37 lamp specifications, 96 password protection, 62 to 67 positioning, 14 to 15 resolution, 7, 95, 99 to 100 transporting, 77 turning off, 41 to 42 turning on, 30 to 32 unpacking, 10 viewing information about, 61 to 62 Q Quick Setup sheet, 9 R Raising image, 37 RCA A/V cable, 22 to 23 Rear projection, 15, 60 Registration, 10 Remote control problems, 91
T V Technical support, 9, 92 to 93 Temperature light, 81 to 82 requirements, 96 Theatre color mode, 40, 54 Timer, lamp, 76 Tint setting, 54 Tracking, adjusting, 56, 87 to 88 Transporting projector, 77 Troubleshooting color, 89 cut-off image, 39, 86 image quality, 87 to 88 image shape, 87 no image, 83 to 85 no sound, 89 to 90 password, 90 pointer, 91 remote control problems, 91, 103 Turning off picture, 45 Turning off projector, 41 to 42 Turning on password, 65 to 66 Turning on projector, 30 to 32 Turning
Index
