2. Attaching the long throw attachment lens Memo Ensure that the lens is attached and detached in a clean room free from dust. Dust entering the inside of the lens may result in damage. 2-1. Removing the front lens unit from the standard lens (1) Remove the front lens cap and cord from the standard lens. Tug on the cord gently to remove it. Cord Front lens cap 12 02_LCL_DTP_E.pm6 Page 12 01.2.15, 3:03 PM Adobe PageMaker 6.
(2) Press down the lever on the front lens unit, and rotate it in the direction of the arrow. (3) Pull it out to remove it. Standard lens Front lens unit Lever Memo • Gently move the front lens unit to the left and right and then pull it out horizontally when removing it. • Do not leave the projector for long periods, or carry it around with the front lens unit detached. Dust entering the inside of the lens may result in damage. 13 02_LCL_DTP_E.pm6 Page 13 01.2.15, 3:03 PM Adobe PageMaker 6.
2-2. Attaching the long throw attachment lens (1) Remove the rear lens cap from the long throw attachment lens. Rear lens cap (2) Align the notch on the long throw attachment lens with the notch on the standard lens. Both notches are marked in red. Notch Standard lens Cord Notch Front lens cap Long throw attachment lens (3) Rotate it in the direction of the arrow until it will turn no further. (4) Insert the end of the cord attached to the front lens cap into the projector’s case.
Memo • Once the lens has been attached, gently move it left and right to ascertain that it is fixed firmly in place. • Use the long throw attachment lens’s rear cap as the rear cap for the front lens unit of a standard lens. • Ensure that both the front and rear lens caps are set in place when the long throw attachment lens and the standard lens front lens unit are not being used. Failure to observe this may result in the lenses getting scratched. Memo • Perform the same procedure as explained in [2-1.
4. Long throw attachment lens specifications 4-1. Lens specifications 1. Focus distance 2. Zoom 3. F number 4. Size 5. Weight : 63.7 to 82.5mm : x1.3 : 1.7 to 2.3 : Diameter 138 x length 101mm : Approximately 1600g 4-2. External view with the long throw attachment lens mounted Approximately 470mm Memo Do not project images with the front lens cap set in place. Failure to observe this may result in lens cap malformation. 17 02_LCL_DTP_E.pm6 Page 17 01.2.15, 3:03 PM Adobe PageMaker 6.
2. Attaching the wide attachment lens Memo Ensure that the lens is attached and detached in a clean room free from dust. Dust entering the inside of the lens may result in damage. 2-1. Removing the front lens unit from the standard lens (1) Remove the front lens cap and cord from the standard lens. Tug on the cord gently to remove it. Cord Front lens cap 12 02_WCL_DTP_E.pm6 Page 12 01.2.15, 3:04 PM Adobe PageMaker 6.
(2) Press down the lever on the front lens unit, and rotate it in the direction of the arrow. (3) Pull it out to remove it. Standard lens Front lens unit Lever Memo • Gently move the front lens unit to the left and right and then pull it out horizontally when removing it. • Do not leave the projector for long periods, or carry it around with the front lens unit detached. Dust entering the inside of the lens may result in damage. 13 02_WCL_DTP_E.pm6 Page 13 01.2.15, 3:04 PM Adobe PageMaker 6.
2-2. Attaching the wide attachment lens (1) Remove the rear lens cap from the wide attachment lens. Rear lens cap (2) Align the notch on the wide attachment lens with the notch on the standard lens. Both notches are marked in red. Notch Standard lens Cord Notch Front lens cap Wide attachment lens (3) Rotate it in the direction of the arrow until it will turn no further. (4) Insert the end of the cord attached to the front lens cap into the projector’s case.
Memo • Once the lens has been attached, gently move it left and right to ascertain that it is fixed firmly in place. • Use the wide attachment lens’s rear cap as the rear cap for the front lens unit of a standard lens. • Ensure that both the front and rear lens caps are set in place when the wide attachment lens and the standard lens front lens unit are not being used. Failure to observe this may result in the lenses getting scratched. Memo • Perform the same procedure as explained in [2-1.
4. Wide attachment lens specifications 4-1. Lens specifications 1. Focus distance 2. Zoom 3. F number 4. Size 5. Weight : 37.2 to 48.1mm : x1.3 : 1.7 to 2.3 : Diameter 116 x length 113mm : Approximately 1400g 4-2. External view with the wide attachment lens mounted Approximately 480mm Memo Do not project images with the front lens cap set in place. Failure to observe this may result in lens cap malformation. 17 02_WCL_DTP_E.pm6 Page 17 01.2.15, 3:04 PM Adobe PageMaker 6.
