Epson PowerLite 755c/765c Multimedia Projector ® ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . 10 Getting More Information . . . . . . . . . . . . . . . . . . . . . . 10 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Unpacking the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Additional Components . . . . . . . . . . . . . . . . . . . . . . . . 12 Optional Accessories . . . . . . . .
2 3 Using the Remote Control . . . . . . . . . . . . . . . . . . 29 Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . 30 Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . 30 Controlling the Picture and Sound . . . . . . . . . . . . . . . . . . . 31 Switching Between Picture Sources . . . . . . . . . . . . . . . . 31 Turning Off the Picture and Sound . . . . . . . . . . . . . . . 32 Stopping Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 5 Presenting Through a Wireless Network . . . 49 Starting EasyMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Configuring the Connection . . . . . . . . . . . . . . . . . . . . . . . . 52 Using Ad Hoc Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Using Access Point Mode . . . . . . . . . . . . . . . . . . . . . . . 59 Using Wireless Security Options . . . . . . . . . . . . . . . . . . . . . 70 Adding WEP Encryption . . . . . . . . . . . . . . . . . . . . . . .
6 Contents Fine-Tuning the Projector . . . . . . . . . . . . . . . . . 107 Using the Menu System . . . . . . . . . . . . . . . . . . . . . . . . . . 108 Restoring the Default Settings . . . . . . . . . . . . . . . . . . 109 Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 Adjusting Signal Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 111 Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . 113 Using the Projector Security Features . .
9 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 151 Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . 152 Checking Projector Status . . . . . . . . . . . . . . . . . . . . . . . . . 153 What To Do When the Lights Flash . . . . . . . . . . . . . . 153 Viewing Lamp Usage and Other Information . . . . . . . 155 Solving Projector Operation Problems . . . . . . . . . . . . . . . . 155 Solving Problems with the Image or Sound . . . . . . . . . . . .
D Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 179 Remote Control Information . . . . . . . . . . . . . . . . . . . . . . 181 Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . 182 FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . 183 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 Index . . . . . . . . . . .
- Welcome The Epson ® PowerLite® 755c/765c is an easy-to-use projector that weighs less than 4 pounds. The projector offers up to 2500 lumens (765c) or 2000 lumens (755c) of brightness. You can connect it to a wide range of computers and video sources, or you can project from a USB storage device, memory card, or over an 802.11g or 802.11b wireless network.
Using Your Documentation This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector. ■ Tips contain additional projection hints.
■ If you still need help after checking this User’s Guide and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on the card in your Start Here kit. Or take advantage of Epson’s automated support services 24 hours a day. See page 166 for more information.
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: Remote control and batteries EasyMP software CD-ROM Projector Audio adapter USB cable Power cable VGA computer cable 802.11G/B wireless card Carrying case Save all packaging in case you need to ship the projector. Always use the original packaging (or the equivalent) when you need to send the projector to another location. If you are moving the projector by hand, use the carrying case.
■ To receive a component video signal from a VCR or other video device, you’ll need a component video cable. You can purchase one from Epson; see below. ■ Some older PowerBooks® and Macintosh® desktop models may need the Macintosh desktop adapter set shown on page 39 (available from Epson; see below). Older iMac® systems may need a special adapter to provide a VGA output port; see your computer dealer.
Welcome
1 Displaying and Adjusting the Image W hether you’re presenting from a computer or video equipment, you need to follow some basic steps to display your image on the screen.
Positioning the Projector note You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 173 for details. If the projector isn’t already installed in the room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.
Ideally, you should place the projector directly in front of the center of the screen, facing it toward the screen squarely. The base of the lens should be at about the level of the bottom of the screen. note After positioning the projector, you may want to connect a Kensington MicroSaver® anti-theft device to the lock port on the projector’s left side. You can purchase this from Epson; see page 13.
Projecting the Image Make sure your projector and other equipment are set up as described on page 37. Then follow the instructions below to start the projector and display an image. Turning On the Projector note To shut down the projector, see page 26. Shutting down the projector correctly prevents premature lamp failure and possible damage from overheating. Turn on any connected computer or video equipment before starting the projector so it can automatically detect and display the image source.
3. Press the red P Power button on the remote control or on top of the projector. The projector beeps once and the Power light flashes green as the projector warms up, then an image begins to appear. When the Power light stops flashing and remains green, the projector is ready for use. 4. If you’ve connected a Windows®-based computer to the projector, you may see a New Hardware Wizard screen saying your computer has found a plug-and-play monitor; if so, click Cancel.
Troubleshooting Display Problems Follow these guidelines if you’re having trouble displaying an image. You Can’t Project an Image If you don’t see the image you are trying to project, try the following: ■ Make sure the cables are connected correctly, as described beginning on page 37. ■ Make sure the Power light is green and not flashing and the lens cap is off.
■ If the function key doesn’t permit you to display simultaneously on both screens, you should check your monitor settings to make sure both the LCD screen and the external monitor port are enabled. From the Control Panel, open the Display utility. In the Display Properties dialog box, click the Settings tab, then click Advanced. The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled.
If you’re using OS 8.6 to OS 9.x: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Control Panels, then click Monitors or Monitors and Sound. 2. Click the Arrange icon. Click here Drag one monitor icon on top of the other 3. Drag one monitor icon on top of the other. If the Arrange option isn’t available, you may need to select one of the Simulscan resolution settings: 1. Click the Monitor icon.
Adjusting the Image Once you see your image, you need to make certain adjustments: ■ If the image is too high or too low, you can reposition it. See below. ■ To focus or zoom your image, see page 24. ■ If the image isn’t square, see page 24. ■ If a computer image displays incorrectly, see page 26. If you need to fine-tune the image and/or sound, see Chapter 6. Adjusting the Height of Your Image If the image is too low on the screen, you can use the front adjustable foot to raise it. 1.
Focusing and Zooming Your Image Turn the focus ring on the projector to sharpen the image. Turn the zoom ring on the projector to reduce or enlarge the image. Focus Zoom If the image still isn’t large enough, you may need to move the projector farther away from the screen. You can also use the E-Zoom buttons on the remote control to zoom in on a portion of the image. See page 33 for instructions.
If your image is still distorted, you can correct it using the Keystone buttons on the projector’s control panel or the projector’s Setting menu. Keystone correction Using Keystone Correction To adjust your image when it is wider on the top or bottom, do the following: ■ ■ Press one of the two triangular buttons on the projector’s control panel, as shown below. Continue pressing the button until you are satisfied with the shape of the image. note The image will be slightly smaller after adjusting.
Correcting Computer Images note You must be projecting an image for this button to have any effect. The Auto button works only with computer images. If you’re connected to a computer and the image doesn’t look right, press the Auto button on the remote control or the Enter button on the projector. This automatically resets the projector’s tracking, sync, resolution, and position settings.
3. Press the P Power button again. The lamp turns off. When the projector beeps twice (after about 3 seconds), you can unplug the power cord. (If the projector is mounted on the ceiling, you will need to wait 10 seconds for the projector to cool down before you can unplug the power cord.) If you want to turn the projector on again, make sure the orange light is not flashing, then press the P Power button. caution Turn the projector off when not in use.
Displaying and Adjusting the Image
1 Using the Remote Control T he projector includes a number of tools to enhance your presentation. All of them can be accessed using the remote control, which lets you operate the projector from anywhere in the room—up to 20 feet away. note For information and resources to help you give the most professional presentation, be sure to visit presentersonline.com. You can use the remote control to adjust the picture and sound (page 31) or as a pointer to highlight your presentation (page 36).
note If a button is pressed longer than 30 seconds, the remote control stops operating to conserve power. When you release the button, normal operation resumes. Using the Remote Control Follow these tips for using the remote control: ■ Point the remote control at the front of the projector or at the screen. ■ Stand within 20 feet of the projector. ■ Avoid using the remote under bright fluorescent lamps or in direct sunlight, or the projector may not respond properly.
Controlling the Picture and Sound You can use the remote control to preview and select your picture sources, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, and adjust the volume.
Turning Off the Picture and Sound You can use the A/V Mute button on the remote control to turn off the image and sound. This feature is useful if you want to temporarily redirect your audience’s attention. ■ To turn off the picture, press the A/V Mute button. The screen turns blue. ■ To turn the image back on, press the button again. You can have the screen turn black when you press the A/V Mute button. You can also have an image, such as a company logo, display on the screen (see page 117).
Zooming Part of Your Image You can zoom in on a portion of the image using the E-Zoom buttons on the remote control. 1. Press the E-Zoom button on the remote control. You see a crosshair indicating the center of the zoom-in area. 2. Use the pointer button to position the crosshair. button to enlarge the selected 3. Continue pressing the E-Zoom area up to 4 times. 4. While the image is enlarged, you can: ■ Use the pointer button to move around the screen. ■ Press the E-Zoom button to zoom out. 5.
Resizing Video images You can use the Resize button on the remote control to adjust how an image fits into the display area. For video images, press Resize to switch the aspect ratio between 4:3 and 16:9. This lets you play certain digital video images or movies recorded on certain DVDs in 16:9 widescreen format. For computer images, resizing is normally unnecessary, since the projector automatically resizes the image to make the best use of the display area.
Operating Your Computer with the Remote Control If you’ve connected a computer to the projector with a USB cable, as described on page 40, you can use the remote control in place of your computer’s mouse. This gives you more flexibility when delivering slideshow-style presentations, since you won’t have to stand next to the computer to change slides. ■ Use the Up and slideshow.
Highlighting Your Presentation You can display a pointer to call out important information on the screen. If you want to customize the pointer tool, you can choose from three alternative shapes. Using the Pointer Tool 1. To activate the pointer tool, press the Pointer button on the remote control. A pointer appears on the screen. Pointer If you prefer to use a different style of pointer, see the instructions in the next section. 2.
1 Connecting to Computers, Cameras, and Other Equipment T his chapter tells you how to connect the projector to a notebook or desktop computer, and/or to video equipment, such as a VCR, DVD player, or video camera. You can also connect the projector to a USB storage device, digital camera, or external speakers.
note If you connect a Windowsbased computer to the projector, you may see a New Hardware Wizard saying your computer has found a plug-and-play monitor; if so, click Cancel. note For newer PowerBooks with DVI connectors, see your computer’s documentation to see how to use a DVI to VGA adapter (usually included with the computer) to connect to the VGA computer port.
3. When you’ve finished making any connections, see page 18 for instructions on turning on the projector and adjusting the image. Using the Macintosh Desktop Adapter If you have an older desktop Macintosh or PowerBook, the VGA cable may not fit when you try to connect it. If so, you’ll need to use the Macintosh desktop adapter to connect the VGA cable to your computer. This is available from Epson (see page 13). 1.
Connecting the Cable for Remote Mouse Control If you’ve connected a computer as described in this chapter (using the Computer/Component Video port), you can use the projector’s remote control as a wireless mouse. This lets you control your computer and click through slideshow-style presentations, such as PowerPoint, from up to 20 feet away. note The remote mouse control function may not operate correctly on systems that have been upgraded from an earlier version of Windows.
Connecting to Video Equipment You can connect several video sources to the projector at the same time. Before starting, look at your video equipment to determine its available video output connections: ■ If your video player has a yellow RCA-style video output connector, see “Connecting a Composite Video Source” on page 42. ■ If your video player has an S-Video connector, see “Connecting an S-Video Source” on page 43.
Connecting a Composite Video Source 1. Locate an RCA-style video cable (one is usually provided with your video equipment or you can purchase one from an electronics dealer). 2. Connect the cable to the yellow video output connector on your player and the yellow Video connector on the projector: 3. If you want to play sound through the projector, see page 47 for instructions on connecting audio cables. 4.
Connecting an S-Video Source 1. Locate an S-Video cable (one is usually provided with your video equipment or you can purchase one from Epson; see page 12). 2. Connect the cable to the S-Video connector on your player and the S-Video connector on the projector: 3. If you want to play sound through the projector, see page 47 for instructions on connecting audio cables. 4.
Connecting a Component Video Source You will need a component-to-VGA video cable or a component video-to-VGA adapter for this connection. You can order this cable (ELPKC19) from Epson; see page 13 for more information. 1. Locate a component-to-VGA video cable or adapter. note 2. Connect the cable to your player and the blue Computer/Component Video connector on the projector. Be sure your video player is not an RGB video source. If you select the wrong source, image quality may suffer.
Connecting an RGB Video Source 1. Locate the VGA computer cable provided with the projector. 2. Connect the cable to the video port on your player and the Computer/Component port on the projector. note Be sure your video player is not a component video source. If you select the wrong source, image quality may suffer. Check your video player’s documentation. 3. If you want to play sound through the projector, see page 47 for instructions on connecting audio cables. 4.
Connecting to a Digital Camera or Other Device note Use a cable less than 10 feet long and connect the camera directly to the projector. Your projector may not function correctly if you use a longer cable or connect your camera to a USB hub. If you connect a USB hard drive, make sure you use the AC adapter to power the hard drive. You can connect your digital camera, USB flash memory drive, USB hard drive, or multimedia storage viewer, such as the Epson P-2000 or iPod® photo.
Playing Sound Through the Projector You can play sound through the projector’s speaker system or attach an external speaker system. To play sound through the projector, follow these steps: 1. Locate the appropriate cable and connect it to the Audio jack on the projector. ■ If you have a computer connected to the blue Computer/ Component Video port, use a stereo mini-jack cable.
Connecting External Speakers When you use EasyMP, you can output the sound to external speakers with built-in amplifiers. First, you need to use the Settings menu to set the EasyMP Audio Out option to External. See page 114 for instructions. To connect speakers to the projector, follow these steps: 1. Locate the appropriate cable to connect your speakers.
1l Presenting Through a Wireless Network T his chapter tells you how to send pictures to the projector through a wireless network. Using EMP NS Connection, you can project images shown on your computer screen—including text and graphics—directly to your audience. Because images are displayed in real-time, any changes you make on your PC or notebook are automatically mirrored on the screen.
Starting EasyMP note Only the Epson 802.11G/B card is guaranteed to work. Other brands may not be compatible. Before connecting to the projector, you have to switch it to EasyMP mode. Follow these steps: 1. Turn on the remote control, as described on page 30. Point it at the projector and press the P Power button. 2. Press the EasyMP button on the remote control to select EasyMP as the source. 3. Insert the Epson 802.11G/B card in the card slot with the label facing upward.
Once the card is inserted, you see one of these screens, depending on the currently selected mode: note If you see a message asking you to insert a LAN or memory card, check to make sure your 802.11G/B card is properly inserted. Ad Hoc mode Access Point mode 4. If you’ve already set up your computer and projector for the mode you want to use—Ad Hoc mode (also called computer-tocomputer mode) or Access Point mode (also called infrastructure mode)—skip to “Projecting Wirelessly” on page 74.
Configuring the Connection note Make sure you’ve installed the NS Connection software as described on page 169. To connect to the projector over a wireless network, your computer must be running Windows 98, Me, 2000, or XP. Your Macintosh must be running OS X 10.2.4 or later. See page 169 for complete system requirements for projecting wirelessly. Access Point mode (infrastructure mode) is required to achieve transfer speeds up to 54MB/sec on an 802.11g network.
2. To select Config, press the Enter button on the remote control. 3. Highlight Basic under Wireless LAN and press Enter. You see the following screen: Easy connect mode Make sure Easy connect mode is selected, as shown above. If not, use the pointer button on the remote control to highlight the checkbox next to Easy connect mode, then press Enter to select it. 4. Make sure the projector has a unique name, so you can identify it when connecting to it from your computer.
note character position. When you’re done typing the new name, press Enter. The projector keyword changes each time you turn the projector off and then on again, or remove and reinsert the 802.11g card. Check the keyword on the EasyMP Network screen whenever you start EasyMP and enter that keyword on your computer. You can’t connect using a previous keyword. 5.
Configuring the Network Settings for Windows Before connecting to the projector, you need to make sure the settings for your notebook’s or PC’s network card match the settings you entered for the projector. 1. Access your wireless network Properties window. For example, in Windows XP you would click Start > Control Panel > Network and Internet Connections. Then click the Network Connections icon.
2. Right-click the Wireless Network Connection icon and select Properties. You see a screen similar to this: Click here 3. Click the Configure button. 4. Click the Advanced tab.
5. Check your wireless card’s or adapter’s device settings. (Depending on the type of card or adapter you’re using, some of the settings may be different than those listed here.) ■ Set the Network Type to 802.11 Ad Hoc. ■ Set the SSID to match the name you assigned to the projector’s ESSID. ■ Make sure Encryption is Disabled. 6. Click the General tab and make sure that your wireless card or adapter is enabled. 7. When you’re done, click OK to close the Properties dialog box.
3. Make sure Location is set to Automatic. Select Automatic Select Network Port Configurations then select AirPort note: If you don’t need the other network port configurations, disable them by deselecting their checkboxes. If more than one network port is enabled, the projector software warns you to turn off AirPort when you first connect the projector. Disregard this message. 4. Select Network Port Configurations in the Show pull-down menu. 5. Under Port Configurations, select AirPort. 6.
Using Access Point Mode To use Access Point (infrastructure) mode, first adjust your projector and wireless access point or AirPort base station settings as described in this section. Configuring the Projector 1. Switch the projector to EasyMP and insert the Epson 802.11G/B card (see page 50). You see this screen: 2. To select Config, press the Enter button on the remote control. 3. Highlight Basic under Wireless LAN and press Enter.
Make sure Access point mode is selected, as shown above. If not, use the pointer button on the remote control to highlight the checkbox next to Access point mode, then press Enter to select it. note If you want to enter a blank space, use the space character that comes before the capital letter A. If you want to enter numbers, use the numeric keypad while holding down the Num button on the remote control. Press the Num button again to exit numeric keypad mode.
8. If your access point assigns IP addresses automatically, turn on DHCP. Otherwise, turn off DHCP and enter the following information manually: ■ ■ ■ IP address: Type in the IP address you want to assign to the projector. It must be formatted like other addresses on the network. The last section should be unique. Subnet mask: For example: 255.255.255.000, but this depends on how your network is set up.
Configuring the Network Settings for Windows Before connecting to the projector, you need to make sure the settings for your computer’s wireless card or adapter match the settings you entered for the projector. note On some Windows systems, you can right-click My Network Places or Network Neighborhood on the desktop and select Properties. 1. Access your wireless network Properties window. For example, in Windows XP you would click Start > Control Panel > Network and Internet Connections.
You see a screen similar to this: Click here 3. Click the Configure button. 4. Click the Advanced tab.
5. Check your wireless card’s or adapter’s device settings. (Depending on the type of card or adapter you’re using, some of the settings may be different than those listed here.) ■ Set the Network Type to Infrastructure. ■ Set the SSID to match the name assigned to the access point (which should also be the projector’s ESSID). ■ Make sure Encryption is Disabled if you have not set up encryption on the projector. 6. Click the General tab and make sure that your wireless card or adapter is enabled. 7.
9. Select Internet Protocol and click the Properties button. You see this screen: 10. If your access point uses DHCP, select Obtain an IP address automatically. Otherwise select Use the following IP address and enter the required information: ■ IP address: Type in the IP address you want to assign to the note For specific details about your network, please consult your network administrator. computer. It must be formatted like other addresses on the network. The last section must be unique.
You see a screen like this: 13. Verify that you’ve enabled your computer’s connection to the access point. It should be listed with the small icon next to it, indicating a connection. If it’s not listed, click Configure and type the name of your access point. 14. When you’re done making settings, click OK to close the dialog box. Now you’re ready to connect to the projector. See “Projecting Wirelessly” on page 74.
Checking the Gateway IP Address on Windows If you’re entering IP addresses manually and need to find out the gateway IP address (the IP address of your access point), make sure the wireless connection to the access point is currently active, as described in the previous section. Then follow these steps: 1. Access your wireless network Properties window. For example, in Windows XP you would click Start > Control Panel > Network and Internet Connections. Then click the Network Connections icon.
3. Click the Support tab. The gateway’s IP address is listed as shown: Gateway address Setting Up Your Macintosh for Access Point Mode Your AirPort software is automatically configured to allow your Macintosh to detect Access Point networks. Typically, you only need to select your AirPort network name from the AirPort status menu on the Macintosh menu bar. If you’re having problems connecting to the projector, follow these steps: 1. From the Apple pull-down menu, select System Preferences. 2.
3. Make sure Location is set to Automatic. Select Automatic note If you don’t need the other network ports, disable them by deselecting their checkboxes. If more than one network port is enabled, the projector software warns you to turn off AirPort when you first connect the projector. Disregard this message. Select Network Port Configurations then select AirPort 4. Select Network Port Configurations in the Show pull-down menu. 5. Under Port Configurations, select AirPort. 6. Click Apply Now.
10. Click the AirPort icon on the menu bar at the top of the Macintosh desktop. You see the AirPort status menu: 11. Check to make sure AirPort is turned on. 12. Select the name of your AirPort network. Using Wireless Security Options You can use the following security options when connecting to the projector wirelessly: WEP encryption, WPA security, or LEAP authentication. To set these security features up on your wireless network, see your documentation or get help from your network administrator.
Adding WEP Encryption When you click the Security button on the Network screen, you see this screen: note 1. Highlight WEP and press Enter. 2. For the WEP encryption setting, highlight 128Bit or 64Bit and press Enter. 3. For Format, highlight HEX to enable hexadecimal input, then press Enter. 4. If you chose 64Bit, highlight Key ID 1, 2, 3, or 4. 5. Highlight the Encryption key text box and press Enter. The box turns yellow to indicate you are in input mode.
■ For 64 bit WEP encryption with hexadecimal input, enter 10 characters, from 0 to 9 and from A to F. ■ For 128 bit WEP encryption with ASCII or text input, enter 13 alphanumeric characters. ■ For 64 bit WEP encryption with ASCII or text input, enter 5 alphanumeric characters. 6. When you’re done making settings, highlight the OK button at the top of the screen and press Enter.
3. When you’re done making settings, highlight the OK button at the top of the screen and press Enter. Adding LEAP Authentication When you click the Security button on the Network screen, you see this screen: 1. Highlight LEAP, then press Enter. 2. Enter the user name and password that match the settings on your authentication server: ■ ■ Highlight the User name text box and press Enter. The box turns yellow to indicate you are in input mode.
then press the pointer button to the right to move to the next character position. When done typing the password, press Enter. 3. When you’re done making settings, highlight the OK button at the top of the screen and press Enter. Projecting Wirelessly Once you’ve started EasyMP and set up your projector and computer in either Ad Hoc mode or Access Point mode, follow these steps to start NS Connection and project wirelessly. 1. Make sure you’ve installed your 802.
You see the screen below. (If you have previously started NS Connection, this is the first screen you see.) Select projector If the connection is working properly, you see your projector listed. If you have additional Epson projectors on the network, they are also listed, along with their status.
the AirPort icon on your menu bar) to make sure AirPort is turned on and the projector’s ESSID or your AirPort network is selected. note The AirPort network name may be different than the AirPort base station name. To check the network name, start the AirPort Admin utility, select your base station, and click Configure. Then click Show All Settings. The network name appears on the AirPort tab. 76 ■ Make sure you aren’t projecting one of the EasyMP configuration screens.
4. Once the name of your projector appears, select it and click Connect. If more than one projector is listed, you can select additional ones and connect to them at the same time. If the selected projector is already being used by another person, you can still connect to it (unless it is “locked”); doing so automatically disconnects the other user. If a projector is locked, you won’t be able to connect to it when it is in use. 5.
Using the Control Bar From the control bar, you can access these NS Connection features: Provides help for NS Connection. Locks the projector while it is in use and prevents anyone else from connecting to it (Windows only) Limits projection to PowerPoint presentations only (Windows only) Lists projectors and specifies which ones are in use. Lets you access the projector’s menu system from an HTML browser window. See page 132 for more information.
Clicking one of the buttons on the control bar may cause a submenu to appear above the control bar. For example, clicking the button displays the following submenu: Click to close If you’re using more than one projector, you can use the Projector drop-down menu to select the projector on which you want to make any of the following changes: ■ Brightness Increase or decrease brightness.
Connecting in IP Connect Mode note Depending on your network, your projector and computer may connect over different routers even if they are in the same room. Try this method if you are unable to connect automatically. You can establish a connection manually using IP Connect Mode even if your projector and computer are on a different subnet (Access Point mode only) or connecting over different routers. 1. Start NS Connection (see page 74). You see this screen: Click here 2. Click the Extension button.
3. Select Use IP connect mode and click OK. You see this screen: Click here 4. Click IP connection. You see this screen: Enter the IP address and click Search note 5. Enter the projector’s IP address and click Search. You can add up to 16 projectors to the list. If you add more, NS Connection begins to delete projectors from the list, starting with the first projector added.
The IP address appears in the Projector list and a searching icon displays. When the projector is found, its name appears in the list: This icon appears if the search fails to find the projector note If the search fails to find a projector with the specified IP address, the searching icon turns into a question mark. If this happens, run EasyMP on your projector (see page 50) to check the projector’s IP address, then repeat this step. You can connect to a 6.
Switching Between Users To connect to the projector while another person is already using it (Access Point mode only), follow these steps. 1. Start NS Connection (see page 74). You see this screen: note If a projector is in use and is “locked,” you won’t be able to select it. Select projector 2. Select the projector you want to use and click Connect. You see this message: 3. Click Yes to connect.
Removing the Wireless 802.11g Card Follow these steps to remove the card from your projector. 1. If you’re running NS Connection, click Disconnect on the control bar. Click Disconnect caution Never remove the card while the card indicator light is green or when projecting wirelessly. You may damage the card or lose data. 2. Check the card access light to make sure it isn’t flashing. Then press the eject button. The button pops out. Eject button Access light 3. Press the eject button again.
1 Presenting from a Memory Card, Digital Camera, or External Drive T he projector’s EasyMP feature lets you give presentations from a memory card or a digital camera connected to the projector with a USB cable. You can play movies, display graphics, or play a scenario, a format that lets you create your own slideshow using PowerPoint files, JPG image files, and BMP graphics files. This chapter covers the following: note To create a scenario, you need a memory card and a card reader on your computer.
note If a digital camera is connected to the projector, disconnect it before inserting the memory card. The memory card is not functional when a digital camera is connected. caution Inserting a Memory Card in the Projector Follow these steps to insert the memory card in the projector: 1. If necessary, insert the card into a PC card adapter. (ATA flash cards don’t require an adapter.) 2. Insert the card (with the adapter) into the projector with the label facing up.
Creating a Slideshow on the Fly If you have a folder on your memory card containing an assortment of images, you can display them as a slideshow. Displaying the Slideshow First make sure the images are stored in a folder on the memory card. Then follow these steps: 1. Use the pointer button on the remote control to highlight the folder containing your images and press Enter. Select Play Slideshow 2. From the drop-down menu, use the pointer to select Play Slideshow and press Enter.
■ Press the appropriate side of the slide or image on the screen. pointer button to rotate a ■ To exit the slideshow at any point, press the Esc button. Press the Enter button to confirm that you want to exit. Changing Timing and Other Settings For each folder on the memory card, you can set the display timing for your slides and change several other display settings. 1. Select the folder containing the images for the slideshow settings you want to change and press Enter. 2.
■ Display order Lets you choose between displaying alphabetically by file name or by image file date. ■ Effect Lets you choose from various transitions between slides, such as Dissolve or Wipe. ■ Mode switching Lets you choose the mode to use when presenting slideshows, movies, or images, or editing a scenario on the projector. In Guide mode, a drop-down menu appears whenever you select an item and press Enter.
note Make sure your camera shows up on your desktop as a drive letter. If it does, it is probably a USB mounted device and will work with the projector software. The EasyMP software does not support TWAIN-compliant digital cameras. If your camera’s memory card is supported by the projector, you can insert it into the projector’s card slot and project your images (see “Creating a Slideshow on the Fly” on page 87). You can’t have your camera connected at the same time. 4.
2. Plug in your external hard drive. 3. Turn on the projector and the remote control, if they’re not already on. 4. Select EasyMP as the source by pressing the EasyMP button on the remote control. 5. Use the pointer button on the remote control to position the cursor on the folder where your photos or movies are stored and press Enter. 6. Select Open Folder in the drop-down menu. When the folder opens, you see another folder with your manufacturer’s name. 7.
Creating a Scenario note To create a scenario, you need a memory card and a card reader on your computer. Also make sure you’ve installed the EMP SlideMaker software (available for Windows only), as described on page 171. Depending on the type of card you have, you may also need an adapter to use it with the projector. See page 101. A scenario is a combination of images, movies, and/or audio files that you can present from a memory card.
5. When you see a message that the slideshow is complete, left mouse-click or press Enter as prompted. You see your scenario as shown below. The scenario is made up of individual cells for each of the PowerPoint slides. Scenario Cell 6. At this point, you can insert additional images or create transition effects between slides. (See “Building a Scenario from Different Files” on page 96 and “Setting Up Transitions” on page 98 for details.
Creating a Scenario from Scratch Use this method when you want to create a scenario from a selection of PowerPoint slides, graphics, or movie files. You’ll need to set up your scenario file and folder, build the scenario, set up transitions, and check the scenario. Setting Up the Scenario File and Folder 1. Double-click the EMP SlideMaker2 icon on your computer’s desktop (or click Start > Programs or All Programs > Epson Projector > EMP SlideMaker2).
2. Choose New from the File menu. You see the scenario Properties dialog box: 3. Type a name for your scenario file and folder that’s easy to remember, using up to eight capital letters and numbers. Then select from the following options: ■ The default location for the scenario file and folder is in the \Program Files\EMP SlideMaker2 folder. Click Browse to choose a new location. ■ Click Configure BGM(W) to play an audio file during the scenario. A selection screen appears letting you choose a .
note You can also use the instructions in this section to add files to an existing scenario. Building a Scenario from Different Files You can build your scenario from any of the following file types, either alone or in combination with other file types: ■ PowerPoint slides, version 2000 through 2003 (file names have .PPT extension) ■ JPEG files (with .JPG extension) ■ Bitmap files (with .BMP or .DIB extension) ■ Movie files (with .
3. Drag and drop the files you want to include in your scenario from either the file window or thumbnail window into the scenario window. (You can also double-click a thumbnail to add the file to the scenario.) Scenario Cell Check a slide’s animation effects here To include a whole PowerPoint file (instead of individual slides), drag the PowerPoint icon itself into the scenario window. Dragging an entire file preserves the transitions set in PowerPoint. 4.
6. When you’re done, click the Save button or choose Save from the File menu. Then see page 101 to transfer the scenario to your memory card. Setting Up Transitions EMP SlideMaker 2 lets you set your slides to advance manually or automatically after a specified period of time. You can also choose from a variety of transition effects between slides. 1. Click the cell or cells for which you want to set up in the scenario window. To select more than one cell, hold down the Ctrl key while you click.
3. Click Cell Properties. You see this dialog box: Click to change slides manually Click to change slides automatically Select transition effects 4. Choose how you want to advance to the next cell. ■ If you want to change slides manually using the remote control, select On mouse click. ■ If you want your slides to advance automatically, set the timing in the Automatically after box. You can set any length of time between 1 and 1800 seconds (30 minutes).
Checking Your Scenario You can play your scenario before you transfer it to a memory card to make sure it looks and sounds the way you want it to. 1. Use the navigation tools in the folders window to locate the scenario file you want to review. Click the file, then click File > Open to open the scenario. 2. Click Scenario Option(s) > Scenario Preview. The Scenario Preview window displays. If the scenario is set to advance automatically (see page 99), it begins to play.
Transferring Your Scenario to a Memory Card Once your scenario is saved, you can transfer it to a memory card or USB storage device. You can use any of the following standard cards. Most require a PC card adapter to allow insertion into the projector (check with your computer dealer to purchase a PC card adapter).
Once the scenario is transferred, you see this message about your scenario’s autorun setting: The autorun setting means that the scenario will start playing whenever the projector is turned on (with the memory card in the projector). 7. Do one of the following: ■ If you don’t want the scenario to run automatically, click Cancel. Skip to step 11 to remove the card and insert it in the projector. ■ If you want it to run automatically, click OK and continue with the following instructions.
10. When done, click OK. 11. Remove the card from your computer or disconnect the USB device. See your computer’s documentation if you need instructions on removing the card. If you’re using Windows 2000 or Me, you may first need to click an icon to stop or disconnect the card. Presenting Scenarios Before you begin, insert the memory card containing the scenario into your projector, as described on page 86. The follow these steps to present your scenario: 1. Turn on the projector, if it’s not already on.
note Your files may take up more than one screen. If so, use the Page up and Page down buttons on the remote control to view all your files. 3. Use the pointer button on the remote control to highlight your scenario file and press Enter. A drop-down menu appears under the scenario. 4. Use the pointer button to select Play Scenario and press Enter. In a moment, your scenario begins playing. 5.
Editing Your Scenario on the Projector You can modify your scenario using EasyMP on the projector. This lets you make last-minute changes, such as changing the order of your slides or hiding individual slides. These changes are not permanently saved with the scenario, but remain in effect only as long as the card is in the projector and the projector is turned on. 1. Highlight the scenario you want to edit, then press Enter. 2. From the drop-down menu, select Edit Scenario.
Supported File Formats The following file types may be projected from a memory card, digital camera, external hard drive, or flash memory drive: File Type Extension Notes Scenario .sit These are scenario files created using the EMP SlideMaker 2 program that is included with the projector. Graphics .bmp Only 24-bit color files can be played. .gif Images with a resolution greater than 1024 × 768 cannot be projected. .
1 Fine-Tuning the Projector Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features.
Using the Menu System You can use the remote control or the projector’s control panel to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control or on the projector. You see a menu screen similar to the one below: Options Menu list The menus are listed on the left and the options available for the highlighted menu are shown on the right. 2.
4. After highlighting the option you want to adjust, use the pointer button to change the setting. In some cases, you may have to press the Enter button to view a sub-screen for changing the setting. ■ Press the left or right side of the a slider bar. pointer button to adjust ■ To select from two or more settings, use the pointer button to highlight the desired setting and press Enter. + - ON OFF 5.
Adjusting the Image You can use the Image menu to adjust the brightness, sharpness, color, tint, and contrast. 1. Press the Menu button on the projector or remote control and select the Image menu. You see the Image menu screen. 2. Use the pointer button to highlight the desired option, then adjust it as needed: ■ Color Mode Lets you quickly adjust the color and brightness for various environments. Use either the remote control or the Color Mode setting in the Image menu.
■ Brightness note Lightens or darkens the overall image. ■ The Brightness setting changes the opacity of the projector’s LCD panels. You can also change the lamp’s brightness. Select Brightness Control in the Setting menu, then choose High or Low (the default setting is High). Contrast Adjusts the difference between light and dark areas. ■ Color Intensity (video only) Adjusts the color depth of the image.
2. Use the pointer button to highlight the desired option, then adjust it as needed: ■ Leave this setting ON to automatically optimize the computer image. Turn it off if you want to save adjustments you have made to the video settings. tip Before adjusting tracking or sync, fill the screen with an image containing fine detail. For example, in Windows you can select a pattern to appear as your desktop background. If this option isn’t available, try projecting black text on a white background.
Customizing Projector Features You can use the Settings menu to lock the buttons on the projector, adjust audio volume, and customize several other features. ■ Keystone Squares up the shape of the image after the projector has been tilted upward. If you notice lines or edges looking jagged after adjusting the shape, decrease the Sharpness setting (see page 110). ■ Auto Keystone Automatically compensates for keystone distortion when the projector is tilted upward.
■ note You can also adjust the volume using the remote control. Volume Raises or lowers the volume of the projector’s speaker. ■ EasyMP Audio Out Lets you output sound from EasyMP scenarios (.wav files) or MPEG files to external speakers with built-in amplifiers. Connect the speakers as shown on page 48.
The default setting for the Password Protect function is OFF. Follow these steps to turn password protection on: 1. Press the Freeze button on the remote control for about five seconds. You see this screen: caution If you lose the remote control, you will not be able to enter the password. Keep the remote control in a safe place at all times. 2. Use the pointer button to set Power ON Protect to ON. Then press Enter. 3. Press Esc. 4. Select Password and press Enter. 5.
The countdown for the elapsed time begins as soon as you close the Password Protect menu. (You can check the elapsed time in this menu next to Time elapsed.) 10. To enable your screen logo, select User’s Logo Protect and press Enter. Select ON and press Enter. When this feature is on, the logo appears whenever you turn on the projector (if the Startup Screen is enabled in the Extended menu; see page 117).
When you see the Password Protect Release screen again, you can try to enter the correct password. If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson to unlock it. If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for assistance. See “Where To Get Help” on page 166.
3. When you see a message asking whether you accept the present image as the user’s logo, select Yes and press Enter. A selection box displays over the image. 4. Use the pointer button to select the area of the image you want to use. Then press Enter. 5. When you see the message Select this Image?, highlight Yes and press Enter. 6. Use the arrow buttons to select a zoom rate (display size) and press Enter. 7. When the message Save image as user’s logo? appears, select Yes and press Enter.
Disabling the Projector’s Buttons When you enable the Operation Lock function, you can lock all the projector’s buttons except the Power button. 1. Press the Menu button, highlight the Setting menu, and press Enter. 2. Select Operation Lock and press the Enter button. 3. Select ON and press Enter. 4. Select Yes and press Enter to confirm the setting. 5. Press the Menu button to exit.
■ Projection Select Front (to project from the front of a screen and right side up), Front/Ceiling (when the projector is mounted upside-down from the ceiling), Rear (to project from behind onto a transparent screen), or Rear/Ceiling (to project from behind onto a transparent screen when the projector is mounted upside-down from the ceiling). When you select one of the Ceiling projection methods, the projector requires a 10-second cool-down after you turn it off.
1 Managing Projectors T he software included with your projector lets you monitor and control your projectors from a remote computer: ■ Use EMP Monitor (available for Windows only) to see your projectors’ status, switch image sources, and control basic settings. ■ Use the mail notification function to receive e-mail alerts about possible problems.
Using EMP Monitor note If you want to monitor projectors while they are in standby mode, select Standby Mode in the Extended menu, then select Network ON. See page 120. EMP Monitor lets you use a remote computer to manage your projectors, whether connected wirelessly or over a wired network. It lets you easily turn the projectors on or off (together or individually), switch image sources, and check their status.
Registering Your Projectors Before you can monitor your projectors, follow these steps to register them: 1. Click Start > Programs or All Programs > Epson Projector > EMP Monitor or click the EMP Monitor icon in the taskbar. You see this screen: Click here 2. Click Register projector. You see this screen: Click here note If Auto detect fails to find the projector, your projector may not be connected or configured correctly for the network. See page 52 to configure the projector for a wireless network.
Any projectors found on the network are listed as shown below: Click here 4. Select each projector you want to add by clicking its name, then clicking the Add button. When you’re done, click Close. note You see this screen with a list of all registered projectors. To delete a projector from the list, highlight the projector name, and click Delete. 5. Click Close.
You see the status of each of your registered projectors on the main EMP Monitor screen: Monitoring Your Projectors The EMP Monitor screen lets you monitor your projectors using the Status, Video Source, and Error icons shown below. These let you see which projectors are currently being used, from which source (or port) they are projecting an image, and if a problem occurs.
The following table explains the meaning of the status icons: Status icons (green) Projecting; no problems (dark) Turned off; no problems (green) Projecting; problems detected (dark) Turned off; problems detected Network error (for example, not connected to the network or power cable disconnected). You may also see this error if Network OFF is selected in Standby Mode (see page 120).
The following table explains the meaning of the error icons. See page 151 for recommended solutions to problems.
The following table explains the functions of the control buttons: Control buttons Turns the projector on Turns the projector off Changes the video signal to the Computer/Component 1 port Changes the video signal to the Computer/Component 2 port Changes the video signal to the S-Video port Changes the video signal to the Video port Switches the display to EasyMP Using E-Mail Alerts You can set up e-mail alerts to warn you of problems with the projector on either a wireless network or a wired LAN connection
You see the following screen: 4. Select Config in the lower right corner of the screen and press Enter on the remote control. 5. When you see the screen below, select Mail and press Enter.
You see the following screen: note To enter numbers with the remote control, hold the Num button and use the numeric keypad. Press the Num button again to exit numeric keypad mode. 6. For Mail Notification Settings, select ON and press Enter. 7. Highlight the IP address of SMTP server box and press Enter. The box turns yellow to indicate you are in input mode. You can enter numbers between 0 and 255. However, you cannot use the following IP addresses: 255.255.255.255, 224.0.0.0, or 127.x.x.
10. If you want to send e-mail alerts to other computers, enter addresses for those computers in the Destination address 2 and Destination address 3 boxes. 11. Select the conditions under which an e-mail alert will be sent. 12. When you’re done, highlight the OK button at the top of the screen (you can either use the pointer button on the remote control or press Esc) and press Enter. Highlight the OK button again and press Enter to return to the main EasyMP Network Screen.
Using a Browser to Monitor Projectors note You can’t use your browser to monitor projectors if it is set up to connect via a proxy server. If you are using Microsoft Internet Explorer, use version 6.0 or later. The projector must be plugged in (projecting or in standby mode) for you to be able to monitor it. To access a projector in standby mode, you must select Network ON as the Standby Mode setting in the projector’s menu system (see page 120.) If your projectors are connected to a network (802.
If you’re connected over an 802.11g wireless network, start NS Connection (see page 74) and connect to the projector you want to monitor. Then click on the control bar that appears on the screen. The projector’s web screen opens in the browser window. Menus Functions corresponding to remote control buttons 4. Select one of the menu options listed on the left, then change any settings as needed in the main part of the screen.
Using Projector Groups tip Use a static IP address when configuring a projector for the network if you plan to use it in a group. If you use DHCP, the projector’s IP address will change every time you turn it off and on again, and you will have to recreate the projector group. If any of the octets in a static IP address are less than 100, the first digit of the octet should be zero (0). You can register projectors as a group if you want to provide quick and easy access to other computers.
4. Click the Advanced button. You see this screen: 5. Enter a name for the group in the Connection Group box. Then enter the IP address of the projector you want to register in the IP address box: note You cannot use the addresses 0.0.0.0 or 255.255.255.255.
6. Click Add. The IP address appears in the list of registered projectors and the searching icon appears beside it. If the projector is found, its name appears in the projector list. note To remove a projector from the group, select it from the projector list and click Delete. 7. Repeat steps 5 and 6 for each projector you want to add to the group. 8. Click OK to save the projectors as a group. When you see a confirmation message, click Yes. 9. Click Close to close the Advanced screen. 10.
Connecting to a Projector in a Group Follow these steps to connect to a projector in a group: 1. Start NS Connection. (See page 74.) 2. Click the Extension button on the EMP NS Connection screen. You see this screen: Select these two boxes 3. Select Use IP connect mode and Use Group List.
4. From the Connection Group list, choose the group you want to connect to and click OK. 5. When you see the next screen, click IP connection. (If the upper left button on the screen says IP connect mode rather than Automatic search mode, skip this step.
You see this screen: Select the projector Then click Connect 6. Select the projector you want to connect to and click Connect. 7. If you want, repeat step 5 to connect to additional projectors. The computer’s image appears on the projector screen. note Exporting a Projector Group You can export group information as a file to another computer on the wireless network. This is useful if you want to share group access with multiple users. 1. Start NS Connection. (See page 74.) 2.
You see this screen: Select these two boxes 3. Select Use IP connect mode and Use Group List. 4. Click the Advanced button. You see this screen. note If you haven’t created any groups, the Export button will be grayed out. You must create at least one group before the Export button is active. 140 Managing Projectors 5. Click Export to export a file for all groups in the Connection Group list.
6. Highlight the file name (NSGroup.ini) and select Save to. 7. Choose a location on the second computer and click Save. To connect to the projector from the new computer, follow the steps beginning on page 137. Importing a Projector Group You can also import group information as a file to another computer on the wireless network. 1. Start NS Connection. (See page 74.) 2. Then click the Extension button on the EMP NS Connection screen. You see this screen: Select these two boxes 3.
4. Click the Advanced button. You see this screen. 5. Click Import. 6. On the next screen, select the file you want to import and click Open. The names of all of the groups in the file are added to the Connection Group list on the Advanced screen. To connect to the projector from the new computer, follow the steps beginning on page 137.
1 Maintaining the Projector warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp cover. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in this User’s Guide. Refer all other servicing to qualified service personnel. Y our projector needs little maintenance.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. Use a canister of compressed air to remove dust. To remove dirt or smears on the lens, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens. Remove the cap before cleaning Cleaning the Projector Case caution Do not use wax, alcohol, benzene, thinner, or other chemical detergents. These can damage the case.
Cleaning the Air Filters and Vents Clean the air filters and air intake vents after every 100 hours of use. If they are not cleaned periodically, they can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. note To order replacement air filters, request part number V13H134A08. See page 13 for ordering information. Follow these steps: 1. Turn off the projector. Wait for the Power light to stop flashing, then unplug the power cord. 2.
Replacing the Lamp and Air Filter note When you get a replacement lamp for your projector, you should replace the filters. The life span of the projection lamp is about 2000 hours if Brightness Control in the Setting menu is set to High (default), and 3000 hours if Brightness Control is set to Low. To check how long the lamp has been in use, see page 155. It is time to replace the lamp when: ■ The projected image gets darker or starts to deteriorate.
4. Turn the projector over. Press in on the tabs and lift up the lamp cover. 5. Loosen the two screws holding the lamp in place (you don’t need to remove them). Loosen, but don’t remove these screws note 6. Hold the lamp as shown and pull it straight out. The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. 7. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is facing the right way.
8. Once the lamp is fully inserted, tighten its screws. 9. Slide the air filter out and remove it. 10. Slide in the new air filter until it clicks in place. 11. Insert the two cover tabs, then press down on the cover until it snaps into place. 12. Reset the lamp timer as described in the next section.
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menus. 1. Press the Menu button on the remote control or on the projector’s control panel. You see the main menu. 2. Use the pointer button on the remote control (or the arrow buttons on the projector) to highlight Reset, then press Enter. You see this screen: 3. Select Lamp Hours Reset and press Enter. You see this prompt: 4. Select Yes and press Enter. 5.
Transporting the Projector The projector contains many glass and precision parts. Follow these guidelines to prevent damage: note ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector. ■ When transporting the projector a long distance, first place it in a hard-shell shipping case, then pack it in a firm box with cushioning around the case.
1 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue ? Help button on top of the projector or on the remote control. The following choices are available: ■ Problems with image ■ Problems with sound ■ Problems with source search ■ Language change Follow these steps to get help: 1. Press the blue ? Help button on the remote control or on the projector. You see the Help Menu. 2.
Checking Projector Status If your projector isn’t working correctly, first turn it off, wait for it to cool (the Power light stops flashing orange), and unplug it. Then plug the power cord back in and turn on the projector. If this doesn’t solve the problem, check the lights on top of the projector. What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status.
Status lights Light Status Description Flashing red There is a problem with the fan or temperature sensor. Stop using the projector, disconnect the power cable, and contact Epson as described on page 166. Flashing orange Rapid cooling is in progress. Although this is not an abnormal condition, projection will stop automatically if the temperature rises higher. Make sure there is plenty of space around and under the projector for ventilation, and that the air filters and vents are clear.
Viewing Lamp Usage and Other Information Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used. Press the Menu button and highlight the Info menu. You see the lamp usage hours and various input signal settings on the right. The life span of the lamp is about 2000 hours if the Brightness Control setting in the Setting menu is set to High (default), and 3000 hours if the Brightness Control setting is set to Low.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the Power light is green, not flashing, and the lens cap is off. ■ The projector may be in standby or sleep mode. If the Power light is orange, press the P Power button to turn the projector on. ■ If the power was switched off and then on again, the projector may be cooling down. Wait until the Power light stops flashing and remains orange; then press the P Power button again.
If you’re using a PC notebook: ■ Hold down the Fn key on the keyboard and press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your notebook’s manual or online help for details. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
The message Not Supported is displayed. ■ Make sure the correct input signal is selected in the Signal menu (see page 111). ■ Make sure your computer’s resolution doesn’t exceed UXGA (1600 × 1200) and the frequency is supported by the projector (see page 177). If necessary, change your computer’s resolution setting as described below. Only part of the computer image is displayed. ■ Press the Auto button on the remote control. ■ Make sure the image Position setting is correct on the Signal menu.
The image isn’t square, but keystone-shaped. ■ If the top or bottom of the image is broader, press the button on the projector until the image is square. or ■ If the projector is angled toward the screen from the left or right, the image will be broader on one side. Center the projector in front of the middle of the screen, facing the screen squarely. The image contains static or noise. ■ If you’re using a computer cable longer than 6 feet, or an extension cable, the image quality may be reduced.
You see vertical bands or the image still looks blurry after trying the solutions in the previous section. ■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice vertical bands or some of the characters may look heavy or blurred. Press the Auto button on the remote control to reset the projector’s tracking and sync settings.
■ Try adjusting the Brightness and Contrast settings on the Image menu. ■ Check your computer display settings to correct the color balance. ■ The projector’s lamp may need to be replaced. See page 146 for instructions. There is no sound, or the sound is not loud enough. ■ Press the button on the projector or remote control to increase the volume. ■ Make sure A/V Mute is not enabled. (The A/V Mute button may have been pressed.
Solving Network Problems You don’t see your projector in the EMP Monitor window. ■ Make sure that you’ve connected the projector to the network and configured it correctly; see page 52. Also, make sure you’ve registered the projector with EMP Monitor; see page 122. ■ Make sure that Standby Mode in the projector’s Extended menu is set to Network ON. ■ If the computer you are using is running Windows XP or 2000, you must be logged in as the Administrator. ■ Try restarting your computer.
■ If you’ve changed any settings for your projector or network, or restarted your computer, allow a minute or two for the connection to appear. If you’re using AirPort, try turning AirPort off and then on again. ■ Make sure that you’re trying to connect to the right network. In Windows, verify that you’ve enabled your computer’s connection to the access point (see page 66) or that your wireless card or adapter is enabled and its SSID is set to match the projector’s ESSID (see page 57).
■ If you’re using Access Point mode and you’re connecting to the wrong network, you may be experiencing signal interference from another network. Try resetting your access point or base station, then restart NS Connection. ■ If you’re using AirPort, the projector’s ESSID should match the AirPort network name, not the name of the AirPort base station. To check the network name, start the AirPort Admin utility, select your base station, and click Configure. Then click Show All Settings.
You can’t edit scenario files in EMP SlideMaker after they have been transferred to the memory card. You can only edit scenarios before they are transferred. Open the scenario files saved on your hard drive, make any changes, then transfer the scenario to your memory card. You can’t transfer your slideshow to the memory card because you aren’t able to see the card’s drive letter. You must insert the memory card in your computer’s PCMCIA slot before you select Send Scenario from the Scenario Option(s) menu.
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. ■ The remote control’s batteries may not be installed correctly or may be low on power. To change the batteries, see page 30. ■ Make sure you are within about 20 feet (6 meters) of the projector and within range of the projector’s front or back sensor (approximately 30° to the left or right and 15° above or below). ■ Dim the room lights and turn off any fluorescent lights.
Telephone Support Services To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card included in your Start Here kit. This is the fastest way of speaking to a live representative, and it’s free. This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of these numbers: ■ U.S.
Solving Problems
A Software Installation T note: You can present over a wireless network from a Macintosh running OS X, but you can only monitor the projector from a remote location using a Windows system. he EasyMP software CD-ROM includes the software you need to use the projector’s EasyMP features—for presenting over a wireless network, transferring PowerPoint presentations to a memory card, and monitoring the projector from a remote location.
Macintosh System Requirements Before you install the software, make sure your Macintosh meets the following requirements: ■ Macintosh OS X 10.2.4 or later ■ AirPort (802.11b) or AirPort Extreme (802.
Installing the Software on a Windows System Follow these steps: 1. Insert the EasyMP CD-ROM in your computer’s CD-ROM or DVD drive. You see this screen: 2. Click Install, then follow the on-screen instructions to install your projector software. If you see a message that the Epson GDI Monitor Driver has not passed Windows Logo testing, click Continue Anyway. 3. When installation is complete, close the installation window.
Installing the Software on a Macintosh Follow these steps to install EMP NS Connection: 1. Insert the EasyMP software CD-ROM in your drive. 2. If necessary, double-click the Epson CD-ROM icon to open its window. 3. Double-click the Installer for Mac OS X icon. You see this screen: 4. Click Install, then follow the on-screen instructions to install the software. 5. When installation is complete, close the installation window.
A Projector Installation T his appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
If you’re mounting the projector on the ceiling and you place it above screen level, you’ll have to tilt the projector down to position the image on the screen. This causes the image to lose its square shape. You can correct the distortion using the Keystone function in the projector’s menu system (see page 113). If you place the projector so that the base of the lens is level with the bottom of the screen, the image should be square and you won’t have to adjust it.
A Technical Specifications General Type of display Epson poly-silicon TFT active matrix Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 24 bit, 16.8 million colors Brightness 755c 2000 lumens (High Brightness mode) 1500 lumens (Low Brightness mode) 765c 2500 lumens (High Brightness mode) 2000 lumens (Low Brightness mode) Contrast ratio 400:1 Image size 30 to 300 inches Projection distance 3.2 to 39.7 feet (1.0 to 12.
Projection Lamp Type UHE (Ultra High Efficiency) Power consumption 170 W Lamp life Approx. 2000 hours (High Brightness mode) Approx. 3000 hours (Low Brightness mode) Part number V13H010L32 Remote Control Range 20 feet (6 meters) Batteries (2) Alkaline AAA Dimensions Height 2.7 inches (70 mm), feet retracted Width 10.9 inches (276 mm) Depth 7.6 inches (193 mm) Weight 3.9 lb (1.8 kg) Electrical Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC, 2.7 A 200 to 240 VAC, 1.
Safety United States FCC 47CFR Part 15B Class B (DoC) UL60950 Third Edition Canada ICES-003 Class B CSA C22.2 No. 60950 CE Marking Directive 73/23/EEC Directive 89/336/EEC IEC 60950 Third Edition EN 55022, EN 55024 Pixelworks™ DNX™ ICs are used in this projector. Compatible Video Formats The projector supports NTSC, PAL, and SECAM international video standards, as well as the monitor display formats listed below.
Mode Refresh Rate (Hz) Resolution XGA—60 XGA—70 XGA—75 XGA—85 60 70 75 85 1024 × 1024 × 1024 × 1024 × SXGA1—70 SXGA1—75 SXGA1—85 70 75 85 1152 × 864* 1152 × 864* 1152 × 864* SXGA2—60 SXGA2—75 SXGA2—85 SXGA+60 SXGA+75 SXGA+85 60 75 85 60 75 85 1280 × 1280 × 1280 × 1400 × 1400 × 1400 × SXGA3—60 SXGA3—75 SXGA3—85 60 75 85 1280 × 1024* 1280 × 1024* 1280 × 1024* UXGA—60 60 1600 × 1200* iMAC VGA iMAC SVGA iMAC XGA MAC13 MAC16 MAC19 MAC19-60 MAC21 117 95 75 67 75 75 59 75 640 × 480* 800 × 600*
A Notices This appendix includes safety instructions and other important information about your Epson PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.
■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards. ■ Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled into the projector, or if it has been exposed to rain or water.
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: ■ There is an object between the remote control IR emitter and the IR receiver on the projector. ■ Ambient light is too bright. ■ Certain types of fluorescent lighting are used. ■ A strong light source shines into the IR receiver.
Declaration of Conformity According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: Epson America, Inc. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806-2469 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Warranty Epson America, Inc. Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc.
THE WARRANTY AND REMEDY PROVIDED ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID.
Notices
Index A A/V Mute, 32, 118, 156 Access Point mode, 59 to 70 Access point, checking IP address of, 67 to 68 Accessories, 13, 167 Ad Hoc mode, 52 to 58 Adapter audio, 12, 47 Macintosh, 13, 39 Air filter cleaning, 145 ordering, 13 replacing, 146 to 148 AirPort, configuring for wireless, 57 to 58, 68 to 70 Anti-theft device, 13, 17 Aspect ratio, 175 ATA flash cards, 101 Audio adapter, 12, 47 connecting equipment, 47 to 48 controlling volume, 33 problems, troubleshooting, 161 turning off (using A/V Mute), 32 usin
Continuous play setting, 88, 102 Contrast setting, 111 D Declaration of Conformity, 182 Default settings, restoring, 109 Desktop adapter, Macintosh, 13, 39 DHCP, 61, 65, 69, 163 Digital camera connecting to, 46 projecting images from, 89 to 90 Direct Power On, 27 Display order setting, 89 Distance from projector to screen, 16, 175 Documentation, 10 DPOF, 106 Drive, external, 90 to 91 DVD player, connecting, 41 to 45 E EasyManagement configuring the projector, 52 to 54, 59 to 72 installing software, 169 to
H L HDTV images, video formats, 178 Height of image, adjusting, 23 Help system, using, 152 Help, Epson, 10, 166 to 167 HP OpenView, 61 Lamp number of hours used, 155 ordering, 13 replacing, 146 to 149 specifications, 176 status light, 153 to 154 Lamp timer, resetting, 149 Language setting, 120, 152 Laptop computer connecting to, 38 to 39 display problems, 20 to 22, 156 to 157 selecting source, 19, 31 LEAP authentication, 73 Lens, cleaning, 144 Lights, status, 153 to 154 Living Room color mode, 110 Lockin
Mouse, 175 connecting cable for remote, 40 using remote control as, 35 Movie files, using in scenarios, 96 to 98 MPEG, 106 mpg, 106 mrk, 106 N Network managing projector remotely, 121 to 131 problems, 162 to 164 setting, 125, 127 wireless, 49 to 84 Network card, 169 Network settings, configuring, 52 to 54, 59 to 72, 128 to 131 New Hardware Wizard, 19 No Signal message, 20, 156 to 157 Noise level, 175 Not Supported message, 158 NS Connection, see EMP NS Connection Numeric keypad, using, 53, 115 O Operation
Projector carrying case, 13, 150 cleaning, 144 connections, see Connecting projector disabling buttons, 119 distance from screen, 16, 175 groups, 134 to 142 installing, 173 to 174 lamp specifications, 176 locking, 75 to 78, 83 monitoring remotely, 121 to 133 options, 13 password protection, 114 to 117 positioning, 16 to 17 resolution, 175 specifications, 175 to 177 transporting, 150 troubleshooting, 151 to 154 turning off, 26 to 27 turning on, 18 to 19 unpacking, 12 viewing information about, 155 PSK, 72 R
Sleep mode, 26 SlideMaker, see EMP SlideMaker Slides displaying on the fly, 87 to 89 hiding, 105 rearranging, 105 SmartMedia cards, 101 Software installation, 169 to 172 Sound adding to scenarios, 95 troubleshooting, 161 Source selecting, 19, 31 viewing, 155 Speaker, specifications, 175 Speakers, connecting, 48 Special effects, adding to slide transitions, 89, 99 Specifications brightness, 175 dimensions, 176 electrical, 176 environmental, 176 general, 175 lamp, 176 remote control, 176 resolution, 175 safet
W Warning lights, 153 to 154 Warranty, 11, 184 to 185 Web browser, monitoring projector with, 132 to 133 WEP encryption, 71 to 72 Windows, configuring for wireless, 55 to 57, 62 to 66 Wireless connecting manually, 80 to 82 e-mail alerts, 128 to 131 LEAP authentication, 73 network card, 50, 84, 169 presentation, 49 to 83 problems, 162 to 164 projector groups, 134 to 142 WEP encryption, 71 to 72 WPA security, 72 Wireless, mouse, 35, 40 WPA, 72 Z Zoom ratio, 175 Zooming image, 24, 33 Index 193
Index
Control panel Card slot Zoom ring Exhaust air vent Focus ring Foot adjust lever Remote control receiver Front adjustable foot Enlarge section of image Change slides in PowerPoint Security lock Enter (left mouse button) Lens cover Esc (right mouse button) Activate on-screen pointer Switch between equipment connected to projector ports Optimize computer images Audio port Video port S-Video port Type B USB port PL755c765c_UG_CPD20250R1.
Control panel Card slot Zoom ring Exhaust air vent Focus ring Foot adjust lever Remote control receiver Front adjustable foot Enlarge section of image Change slides in PowerPoint Security lock Enter (left mouse button) Lens cover Esc (right mouse button) Activate on-screen pointer Switch between equipment connected to projector ports Optimize computer images Audio port Video port S-Video port Type B USB port PL755c765c_UG_CPD20250R1.
