EPSON PowerLite 735c Multimedia Projector ® ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Getting the Most from Your Projector . . . . . . . . . . . . . . . . . . 2 Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 3 Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Additional Components.
Turning Off the Picture and Sound . . . . . . . . . . . . . . . 24 Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Changing the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 25 3 4 Presenting Through a Wireless Network . . . . 27 Starting EasyMP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Configuring the Connection . . . . . . . . . . . . . . . . . . . . . . . .
Inserting the Memory Card in the Projector . . . . . . . . . . . . . 65 Removing the Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Presenting the Scenario. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Controlling Your Presentation . . . . . . . . . . . . . . . . . . . . 67 Editing Your Scenario on the Projector. . . . . . . . . . . . . . . . . 68 Creating a Slideshow on the Fly . . . . . . . . . . . . . . . . . . . . . . 69 Displaying the Slideshow . . . . . . . . . . . . . .
9 Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 What To Do When the Lights Flash . . . . . . . . . . . . . . . . . 103 Solving Problems with the Image or Sound . . . . . . . . . . . . 105 Solving EasyMP Problems . . . . . . . . . . . . . . . . . . . . . . . . . 111 Solving Problems with the Remote Control . . . . . . . . . . . . 112 Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . .
- Welcome The EPSON ® PowerLite® 735c is a light-weight, portable projector that offers up to 2000 ANSI lumens of brightness. From classrooms to auditoriums, your full-color presentations and videos will be bright and visible even in ordinary room lighting. With the projector’s EasyMP™ features, you don’t have to worry about connecting a computer. Use your Windows® PC or laptop to project over an 802.11b wireless network—or store your presentation on a memory card for a computer-free presentation.
Getting the Most from Your Projector note Most of the projector’s features can be utilized only with the remote control. To avoid losing the remote control, keep it in the storage compartment in the back of the projector. Your EPSON PowerLite projector can be connected to one computer source and up to three video sources, letting you easily switch between them. (You can connect up to three sources at the same time.) You can also include sound with your computer or video presentation.
Using Your Documentation This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector. Getting More Information Need tips on giving presentations? Quick steps for setting up your projector? Here’s where you can look for help: ■ presentersonline.
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: r Powe puter Com /Video S-Video Menu e r Mod Colo A/V Mu te Freeze E-Zoom Enter ESC Auto Projector Remote control EasyMP software CD-ROM Power cable VGA computer cable RCA-style video cable USB cable 802.11b LAN card Carrying case Save all packaging in case you need to ship the projector.
Additional Components Depending on how you plan to use the projector, you may need additional components: ■ To use EMP SlideMaker2 to create presentations and store them on a memory card, you’ll need a standard Type II memory card as described on page 62. Depending on the type of card you’re using, you may also need a PC card adapter to insert the card in the projector. These products are available from your computer dealer. ■ To receive an S-video signal, you’ll need an S-video cable.
Optional Accessories To enhance your use of the projector, EPSON provides the following optional accessories: Product Product number Replacement lamp and air filter V13H010L18 Customized carrying cases: Samsonite® wheeled soft case Soft shoulder bag Notebook/projector soft shoulder bag ATA wheeled hardshell case for projector/notebook ELPKS24 ELPKS31 ELPKS32 ELPKS42 Ceiling mount Suspension adapter False ceiling plate ELPMB37 ELPMBAPL ELPMBFCP Kensington® security lock ELPSL01 Projection screens:
1 Displaying and Adjusting the Image W hether you’re presenting through a wireless network (Chapter 3), from connected equipment (Chapter 4), or from a memory card (Chapter 5), you need to follow certain basic steps to get your presentation up and running.
Positioning the Projector note You can mount the projector on the ceiling, or place it behind a translucent screen for rear projection. See page 117 for details. If you’re setting up the projector yourself and it isn’t already installed in the theater or conference room you’re using, you’ll probably want to place it on a table in front of the screen, as shown. x art below This lets you stand in the front of the room, face the audience, and remain close enough to the equipment to be able to control it.
To ensure the image on screen is shaped correctly (square or rectangular, not “keystone” shaped), place the projector directly in front of the center of the screen, facing it toward the screen squarely. Projector Screen Overhead View note It’s best to place the projector level with the bottom of the screen, or slightly lower. If you place the projector below screen level, you’ll have to tilt it up by extending its feet.
Projecting the Image Make sure your projector and other equipment are set up as described in Chapter 3 (for wireless network presentations), Chapter 4 (for directly connected computer or video equipment), or Chapter 5 (for memory card presentations). Then follow the instructions below to start the projector and display an image.
3. Press the red P Power button on top of the projector. You can also use the P Power button on the remote control. (If this is your first time using the remote, be sure to remove the plastic tape as shown on page 22.) Power button warning The P power light flashes green as the projector warms up, and the projection lamp comes on in about 40 seconds. Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children. 4.
The control panel and the remote control let you select the source as follows: ■ On the projector’s control panel, the Source button switches between equipment connected to the Video, S-Video, and Computer/Component Video ports, or to EasyMP (for wireless network and memory card presentations). ■ On the remote control, the Comp/EasyMP button lets you switch to a directly connected computer; pressing it again switches to EasyMP.
To remove a card that’s already in the projector, follow these guidelines: ■ For the 802.11b card, simply pull it straight out of the card slot. ■ For a memory card, push in on the eject button so the button extends out (if it’s not already). Then push it a second time to eject the card. note You don’t have to turn off the projector before inserting or ejecting cards.
What To Do If You See a Blank Screen If you’re projecting from connected computer or video equipment and you see a blank screen or a blue screen with the No Signal message, try the following: ■ Make sure the cables are connected correctly, as described in Chapter 4. ■ Make sure the power light is green and not flashing and the lens cover is off. ■ Try restarting your computer.
If you’re using a PowerBook or iBook with OS 9.x: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Control Panels, then click Monitors or Monitors and Sound. 2. Click the Arrange icon. Click here Drag one monitor icon on top of the other 3. Drag one monitor icon on top of the other. If the Arrange option isn’t available, you may need to select one of the Simulscan resolution settings: 1.
If you're using Macintosh OS X: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select System Preferences, then select Displays. 2. Make sure the VGA Display dialog box is selected. 3. Click the Arrange tab. Select the VGA Display dialog box Make sure Mirror Displays is checked 4. Make sure the Mirror Displays checkbox is selected.
Adjusting the Image Once you see your image, you need to make certain adjustments: ■ To focus or zoom your image, see below. ■ If the image is too high or too low, you can reposition it. See page 18. ■ If the image isn’t square, see page 19. ■ If a computer image displays incorrectly, see page 19. Focusing and Zooming Your Image Rotate the focus ring to sharpen the image. Focus ring Rotate the zoom ring to reduce or enlarge the image.
Adjusting the Height of Your Image If the image is too low on the screen, you can raise it by extending the projector’s feet. 1. Stand behind the projector. Press the foot release buttons on each side and lift the front of the projector. 2. Once the image is positioned where you want it, release the buttons to lock the feet in position. 3. If necessary, you can fine-tune the height by turning the projector feet.
Adjusting the Image Shape If the projected image isn’t square or has a “keystone” shape, do the following: ■ If your image looks like or , you’ve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely. ■ If your image looks like or , press the left or right side of the projector’s Keystone button to correct the shape. After correction, your image will be slightly smaller.
Shutting Down the Projector note When the projector has not received any input signals for 30 minutes, it automatically turns off the projector lamp and enters “sleep mode.” This conserves electricity, cools the projector, and extends the life of the lamp. If you want to start projecting again, press the Power button. If you are done using the projector, unplug the power cord. To turn off sleep mode, see page 81. When you’ve finished using the projector, follow the recommended procedure to shut it down.
1 Using the Remote Control T he remote control lets you access your projector’s features from anywhere in the room—up to 20 feet away. You can use it to turn the projector on and off, switch between picture sources, freeze the action, mute the picture and sound, and zoom in on a portion of your image. You can use the remote control to access the projector’s menu system (Chapter 6).
Activating and Using the Remote Control Before using the remote control for the first time, you need to remove the plastic tape as shown below. Remove plastic tape note Avoid placing the projector under bright fluorescent lamps or in direct sunlight, or it may not respond properly to the remote control. 22 When using the remote control, stand within about 20 feet of the projector. Aim it either at the front or back of the projector, or at the screen.
Replacing the Battery If the projector stops responding to the remote control, you may need to replace its battery: When replacing batteries, take the following precautions: 1. Turn the remote control over. 2. Push inward on the latch as shown, then slide out the battery tray. Replace the battery as soon as it runs out. If the battery leaks, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash immediately. ■ Latch 3. Replace the old battery with a new CR2025 lithium battery.
Controlling the Picture and Sound You can use the remote control to select your source, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, or adjust the color. Switching Between Picture Sources If your projector is connected to more than one computer and/or video source, you can switch between the different sources: ■ On the projector’s control panel, press the Source button to switch between the computer, EasyMP, and video sources.
Stopping Action You can use the remote control to stop the action in your video or computer image. ■ Press the Freeze button to stop the action and keep the current image on the screen. The sound continues. ■ Press the Freeze button again to restart it. Zooming Your Image You can zoom in on a portion of the image using the E-Zoom buttons on the remote control. 1. Press the E-Zoom + button on the remote control. A crosshair indicating the center of the zoom-in area appears on the screen. 2.
26 ■ Theater: For optimizing movie images with natural color (the default for video or S-video display) ■ Game: For optimizing games Using the Remote Control
1l Presenting Through a Wireless Network T his chapter tells you how to send pictures to the projector through a wireless network. Using EMP NS Connection, you can project images shown on your computer screen—including text and graphics—directly to your audience. Because images are displayed in real-time, any changes you make on your PC or laptop are automatically mirrored on the screen.
Starting EasyMP Before connecting to the projector, you have to switch it to EasyMP mode. Follow these steps: 1. Turn on the projector, as described on page 10. 2. Select EasyMP as the source, using either the Comp/EasyMP button on the remote control or the Source button on the projector (see page 11). 3. Insert the EPSON 802.11b card (with the blue label facing up). note Only the EPSON 802.11b card is guaranteed to work. Other brands may not be compatible.
Configuring the Connection You can use NS Connection to connect to the projector and send images wirelessly in two modes: Ad Hoc mode or Access Point mode. ■ Ad Hoc mode lets you connect just one PC or laptop to the projector at a time; it’s easy to set up, and the only equipment you need is a computer with a wireless (802.11b) network card.
You see the following screen: Easy connect mode Make sure Easy connect mode is selected, as shown above. If not, use the arrow buttons on the remote control to highlight the checkbox next to Easy connect mode, then press Enter to select it. 3. Use the arrow buttons to highlight Advanced (next to Easy connect mode), then press Enter to select it. You see this screen: 4. Make sure the projector has a unique name, so you can identify it when connecting to it from your computer.
arrows to select individual characters, and use the right arrow to move to the next character position. When done typing the new name, press Enter. 5. To enable your computer to find the projector on the network, select the appropriate Ad hoc mode settings: ■ Select ESSID ad hoc if your network card supports an SSID or ESSID identifier (see page 33). Then enter a name (for example, “CONF ROOM”) in the ESSID text box and press Enter.
You see a screen similar to this: Right-click and select Properties 2. Right-click the Wireless Network Connection icon and select Properties. You see a screen similar to this: Click here 3. Click the Configure button.
4. Click the Advanced tab. You see a screen similar to this: 5. Check your network card’s device settings. (Depending on the type of card or wireless transmitter you’re using, some of the settings may be described differently from those listed here.) ■ Set the network type to 802.11 Ad Hoc. ■ Set the SSID to match the name you assigned to the projector’s ESSID—for example, CONF ROOM. (If your network card uses channel mode instead, set the correct channel, 1 to 11, so it matches that of the projector.
Using Access Point Mode In order to use Access Point (infrastructure) mode, first adjust your projector and network card settings as described in this section. Configuring the Projector To configure the projector for Access Point mode, make sure you’ve switched it to EasyMP and inserted the network card (see page 28). Then follow these steps: 1. On the EasyMP Network Screen, the Config button is already highlighted as shown below. Config button 2.
Make sure Access point mode is selected, as shown. If not, use the arrow buttons on the remote control to highlight the checkbox next to Access point mode, then press Enter to select it. 3. Use the arrow buttons to highlight Advanced (next to Access point mode), then press Enter to select it. You see this screen: 4. Make sure the projector has a unique name, so you can identify it when connecting to it from your computer.
note For specific details about your network, please consult your network administrator. 6. If your access point assigns IP addresses automatically, turn on DHCP. Otherwise, turn off DHCP and enter the following information manually: ■ IP address: Type in the IP address you want to assign to the projector. It must be formatted like other addresses on the network; usually the first three numbers (XXX.XXX.XXX) match the access point’s IP address. ■ Subnet mask: For example: 255.255.255.
Configuring the Network Settings on Your Laptop or PC Before connecting to the projector, you need to make sure the settings for your laptop’s or PC’s network card match the settings you entered for the projector. 1. Access your wireless network Properties window. For example, in Windows XP you would click Start > Control Panel > Network and Internet Connections. Then click the Network Connections icon.
You see a screen similar to this: Click here 3. Click the Configure button. 4. Click the Advanced tab. You see a screen like this: 5. Check your network card’s device settings. (Depending on the type of card or wireless transmitter you’re using, some of the settings may be described differently from those listed here.) 38 ■ Set the network type to Infrastructure. ■ Set the SSID to match the name assigned to the access point—for example, CONF ROOM. ■ Make sure encryption is Disabled.
6. Click the General tab and make sure that the network card or wireless network device is enabled. 7. When done making the settings, click OK to close the network card’s properties dialog box. 8. Right-click the Wireless Network Connection icon again and select Properties. You see this screen: Highlight this, then click Properties 9. Select Internet Protocol as shown above, then click the Properties button.
note For specific details about your network, please consult your network administrator. 10. If your access point uses DHCP, select Obtain IP address automatically. Otherwise select Use the following IP address and enter the required information: ■ IP address: Type in the IP address you want to assign to the computer. It must be formatted like other addresses on the network; usually the first three numbers (XXX.XXX.XXX) match the access point’s IP address. ■ Subnet mask: For example: 255.255.255.
If it’s not listed, click Configure and then type the name of your access point. 14. When done making your settings, click OK to close the dialog box. Now you’re ready to connect to the projector. See “Running NS Connection” on page 42. Checking the Gateway IP Address If you’re entering IP addresses manually and need to find out the gateway IP address (the IP address of your access point), make sure the wireless connection to the access point is currently active, as described in the previous section.
The gateway’s IP address is listed as shown: Gateway address Running NS Connection note Set your monitor’s color to the 16-bit setting for best performance. Higher settings can slow the data transmission speed. Once you’ve started EasyMP and set up your projector and computer in either Ad Hoc mode or Access Point mode, follow these steps to launch NS Connection and project wirelessly. 1. From the Start menu, select EMP NS Connection.
If you don’t see any projectors listed, click Option, then click Switch LAN. Verify that the correct (wireless) network device is selected. Sometimes another network device, such as an Ethernet card, may be selected instead. If you don’t see your wireless device listed, but you’re sure you’ve enabled it as described in “Configuring the Connection” on page 29, you may need to restart your computer. 2. Once the name of your projector appears, select it and click Connect.
4. Once the connection is established, you see your computer’s image transmitted to the projector, and a floating control bar appears on the screen: Click here to minimize 5. If necessary, drag the control bar out of the way, or minimize it to an icon on the taskbar by clicking it as shown above. 6. From the control bar, you can access these NS Connection features: Help provides information on using NS Connection. Connection status screen lists which projectors are available or in use.
E-Zoom lets you zoom in on a part of your image. Basic settings lets you change the brightness, keystone angle, contrast, and color mode. Switch video source lets you switch between the Video and S-Video ports. Switch PC source lets you switch between your computer and EasyMP. 7. When done with your presentation, click Disconnect on the control bar.
You see this message: 3. Click Yes to connect.
1 Presenting from Computer or Video Equipment T his chapter tells you how to connect the projector to video equipment, such as a VCR or DVD player, or to a laptop or desktop computer.
Connecting Video Equipment You can connect a DVD player, VCR, camcorder, laser disc player, digital camera, or any other compatible video source to your projector. You can connect one or more video sources at the same time. 1.
Connecting an Audio Cable If you want to play sound through the projector’s speaker, you’ll need a mini-jack cable (not included). You may also need an mini-jack to RCA adapter to connect the cable to your video equipment. 1. Connect one end of the audio cable to the Audio-In jack on the projector. Audio cable 2. Connect the other end of the cable to the audio-output connector on your video equipment. You may need to use an adapter to plug in the cable.
Connecting a Laptop Before you start, make sure your computer and projector are turned off. 1. Locate the VGA cable that came with the projector. Connect one end to the projector’s Computer/Component Video port. 2. Connect the other end to your laptop’s video-out or monitor port. note If you’re using a PowerBook and you can’t connect the cable, you may need to use the Macintosh desktop adapter as shown on page 51 (available from EPSON; see page 6). 50 3. Tighten the screws on the connectors.
Connecting a Desktop System 1. Disconnect the monitor cable from the video port on the back of the computer. 2. Locate the VGA cable that came with the projector. Connect one end to the projector’s Computer/Component Video port, and the other end to your computer’s video port (where the monitor was connected). note If you have an older Macintosh, you may need the Macintosh desktop adapter as shown on page 51 (available from EPSON; see page 6). 3. Tighten the screws on the connectors.
2. Replace the cover and connect the adapter to the VGA cable. Then plug the cable (with the adapter) into the video port on your Macintosh. 3. Tighten the screws on the connectors. Playing Computer Audio If your computer does not have its own sound system, you can connect a mini-jack cable (not included) to play sound through the projector’s speaker. 1. Connect one end of the audio cable to the Audio-In jack on the projector. Audio cable 2.
Using the Remote Control as a Wireless Mouse If you’ve connected a computer as described in this chapter, you can use the projector’s remote control as a wireless mouse. This lets you control your computer and click through slideshow-style presentations, such as PowerPoint, from up to 20 feet away. note To learn more about using the remote control to run your presentation, see page 24. Connecting the Cable for Remote Mouse Control 1. Locate the USB cable that came with your projector. 2.
Using the Mouse Functions Once the USB cable is connected, you can use the remote control as a mouse pointer as described below. ■ To move the cursor, use the arrow buttons as shown: Page down Page up Use arrow buttons to move cursor Power Comp/Easy MP S-Video/Video Color Mode Menu A/V Mute Freeze E-Zoom Enter Auto ESC ■ To left-click, press the Enter button. ■ To right-click, press the ESC button.
1 Presenting from a Memory Card T he projector’s EasyMP feature lets you give presentations from a memory card. Using the EMP SlideMaker software, you can easily convert a PowerPoint file into a format called a scenario. You can include any combination of PowerPoint slides, JPG image files, and BMP graphics files. Once the scenario is created, you can download it to a memory card, insert the card in the projector, and play the scenario.
Creating a Scenario note Before starting, make sure you’ve installed EMP SlideMaker 2 as described in Appendix A or on the Quick Setup sheet. A scenario is a series of images that you can present from a memory card. The easiest way to create a scenario is to drag and drop a PowerPoint file on the EMP SlideMaker icon on your desktop. This automatically converts the file, which you can save to the memory card.
4. At this point, you can insert additional images or create transition effects between slides (see page 59). 5. Click the Save button or choose Save from the File menu. EMP SlideMaker automatically names your scenario (SCN____) and creates a folder for it within your \Program Files\EMP SlideMaker folder. However, you can choose Save As from the File menu and enter a new scenario name and folder location if you want.
2. Choose New from the File menu. You see the scenario Properties box: 3. Type a name for your scenario. Then select from the following options: ■ The default location for the scenario file and folder is in the \Program Files\EMP SlideMaker folder. Click Browse to choose a new location. ■ The background color (gray) appears around images that don’t fill the entire screen area. Select a new color, if desired. ■ Select the image quality for imported PowerPoint slides.
Adding Images and Transitions to the Scenario Once a scenario file is created (either from an existing PowerPoint presentation or from scratch), you can include additional PowerPoint slides and other graphics. You can also add transitions between each slide. Adding Images You can add the following types of files to your scenario: ■ PowerPoint slides, version 97 (SR-1 or higher) through 2002 ■ JPEG files (file names with .JPG extension) ■ Bitmap files (file names with .BMP or .
3. Drag and drop the images or PowerPoint slides you want to use into the scenario window. To include a whole PowerPoint file (instead of individual slides), drag the PowerPoint icon itself into the scenario window. 4. Continue dragging additional images into the scenario window to build your presentation. Each slide appears in a numbered “cell” as you drop it. The cell background color varies according to the type of file in the cell. 5.
Setting Up Transitions EMP SlideMaker lets you set your slides to advance manually or automatically after a specified period of time. You can also choose from a variety of transition effects between slides. 1. Click the cell or cells you want to set up in the scenario window. To select more than one cell, hold down the Ctrl key while you click. To select all the cells, choose Select All from the Edit menu. Selected cells turn yellow. 2. Right-click the selected cell or cells.
4. Choose how you want to advance to the next cell. note Transition effects look smoother when you create them in the PowerPoint file itself and use that file to create a scenario. ■ If you want to change slides manually using the remote control, select On mouse click. ■ If you want your slides to advance automatically, set the timing in the Automatically after box. You can set any length of time between 1 and 1800 seconds (30 minutes).
Before you start, make sure you are set up to access the card in your computer’s PCMCIA slot or card reader. Be sure to use the transfer process described below to ensure that the scenario plays properly: 1. From the Scenario Option menu, choose Send Scenario. You see a drive selection window: note You have to save the scenario on your computer’s hard drive before transferring it. Don’t use Windows to copy the scenario to your memory card, or it may not play properly. Select your memory card drive 2.
You see the Edit Autorun window: Scenarios on the card note If more than one scenario is set to run automatically, they will play in the order listed on this screen. Scenario set to run automatically 5. To set a scenario to run automatically, select it from the list on the left side of the screen and use the arrow button to move it to the list on the right. 6. Click the Revive box if you want your scenario to repeat continuously. Clear the checkbox if you want it to play only once. 7.
Inserting the Memory Card in the Projector When done transferring your scenario to the memory card, follow these steps to insert it in the projector: 1. If necessary, insert the card into a PC card adapter. (ATA flash cards don’t require an adapter.) 2. Insert the card (with the adapter) into the projector as shown. The projector does not have to be turned off before inserting the card.
Removing the Card When you’re done using the projector and want to remove the memory card, follow these steps. Make sure a scenario is not playing and the card is not in use (the access light next to the card slot is off) before removing it. 1. Press the button next to the card slot. Push button to remove card The button pops out. 2. Press the button again. The memory card is released, and you can remove it from the slot in the projector. 3.
Presenting the Scenario Once you’ve inserted the memory card, you can present your scenario: 1. Turn on the projector, if it’s not already on. ■ If your scenario is set to autorun, it will start as soon as the projector warms up. ■ If your scenario is not set to autorun, you need to start it manually. Continue with the following steps. 2. Select EasyMP as the source by pressing the Comp/EasyMP button on the remote control. You see this screen: note Your files may take up more than one screen.
Editing Your Scenario on the Projector You can modify your scenario using EasyMP on the projector. This lets you make last-minute changes, such as changing the order of your slides or hiding individual slides. These changes are not permanently saved with the scenario, but remain in effect only as long as you don’t remove the card or turn off the projector. Follow these steps: 1. Highlight the scenario you want to edit, then press Enter. 2. From the drop-down menu, select Edit Scenario.
Creating a Slideshow on the Fly If you have a folder on the memory card containing an assortment of images, you can display them as a slideshow. Your options for arranging the slideshow are more limited than when you create a scenario—for example, you won’t be able to include PowerPoint slides, just JPG images and bitmaps, and you won’t have much control over the order in which they’re displayed. However, this method quickly lets you display your images if you don’t have time to make a scenario.
Changing Timing and Other Settings For each folder on the memory card, you can set the display timing for your slides and change several other display settings. 1. Select the Enter. folder whose settings you want to change and press 2. From the drop-down menu, select Options. You see this screen: 3. Use the arrow keys to select from the following settings. After making a selection, press Enter to enable the change. ■ Continuous Play Determines whether to repeat the display of images in the folder.
■ Mode switching Lets you choose how to access EasyMP menu items from the remote control. In Guide mode, a drop-down menu appears whenever you press Enter. To access the menus in Quick mode, you have to press the ESC key. 4. When you’re finished changing the settings, highlight OK on the screen and press Enter. Your changes are permanently saved with each folder—even if you turn off the projector or remove the memory card.
72 Presenting from a Memory Card
1 Fine-tuning the Projector Y ou can use the projector’s on-screen menus to adjust the image, sound, and other features. You can also create your own startup screen and find out how long your lamp has been in use.
Using the Menu System You can use the buttons on the remote control to access the menus and change settings. Follow these steps: 1. To display the menu screen, press the Menu button on the remote control.
5. Use the arrow buttons to change the setting for the selected option; the selection is indicated by an orange highlight. note 6. Press the Enter button to confirm the selection. If you want to go back to the default settings for any menu, you can use the Reset function. 7. Do one of the following: ■ To return to the previous menu, press ESC. ■ To exit the menu system, press the Menu button (or press ESC more than once to exit).
3. Use the arrow buttons to highlight one of these options, then press Enter to select it: ■ Position Adjusts how the image fits on the screen. ■ Tracking (analog computer images only) Removes unwanted vertical lines from a computer image by matching the projector’s internal clock to the computer display signal. ■ Sync (analog computer images only) Corrects fuzziness by synchronizing the projector with the tracking signal sent from the computer. ■ Brightness Lightens or darkens the overall image.
■ Video Signal (video only) Leave this setting at Auto unless you are using a 60-hertz PAL system (select PAL60). ■ Aspect Ratio (all sources except computer RGB) Sets the aspect ratio to 4:3 or 16:9 (letterbox format). ■ Input Signal (computer RGB only) Selects the appropriate source for the device connected to the Computer/Component Video port. ■ Auto Setup (computer RGB only) When switching image sources, automatically optimizes the image.
4. Use the arrow buttons to highlight one of these options, then press Enter to select it: ■ Volume ■ Tone ■ Reset (returns the Audio settings to their default values) 5. After making any needed adjustments, press Menu to exit. Creating Your Own Startup Screen You can transfer any image from your computer or video source to the projector, and then use it as your startup screen.
4. Use the arrow buttons to select the area of the image you want to use. Then press Enter. 5. When you see the message “Select this image?” highlight Yes and press Enter. 6. Use the arrow buttons to select a zoom rate (display size), and then press Enter. 7. When the message “Do you save the user’s logo?” appears, select Yes and press Enter. Confirm as needed. Saving the logo may take a few moments. Do not use your projector or video source (computer, DVD player, etc.) while the logo is being saved. 8.
Customizing Projector Features You can use the Setting menu to disable the projector’s sleep mode, adjust the image shape, and customize several other features. 1. Press the Menu button on the remote control. 2. Use the button to highlight Setting. You see this menu: 3. Press Enter to select the Setting menu. 4. Use the arrow buttons to set the following options: ■ Keystone Lets you correct the shape of the image after the projector has been tilted upward.
■ Color Mode Prompt Sets whether the color mode indicator is displayed on the screen when you press the Color Mode button. ■ A/V Mute Selects the screen color or image to display when you press the A/V Mute button. The logo setting displays an image that you previously transferred to the projector (see page 78). ■ Sleep mode When sleep mode is on, the projector turns off the lamp if it has not received any input signals for 30 minutes.
4. Use the arrow buttons to select one of the following options: ■ Language Select from nine languages to be used for the projector menus. ■ Startup Screen Turn on to display your captured image or logo whenever the projector starts (see page 78). ■ Color Adjustment Adjusts the color temperature of the projected image. Select Color Temp. to set a temperature between 5000 and 10000 K. Select RGB to adjust individual red, green, and blue values, as shown.
Viewing Lamp Usage and Other Information Use the About menu to view information about the display settings of your computer and the number of hours the lamp has been used. 1. Press the Menu button. You see the main menu. 2. Use the arrow buttons on the remote control to highlight About. You see the lamp usage hours and various display settings on the right: Lamp usage The life span of the lamp is about 1500 hours. If the number shown is close to 1500, make sure you have a spare lamp handy.
Restoring the Default Settings The Reset All option lets you return all the projector settings to their default values. Select Reset All and press the Enter button on the remote control to display the confirmation screen. Select Yes to reset all the default settings or No to cancel.
1 Remotely Monitoring the Projector note To monitor and control your projector(s) through HP OpenView, install the plug-in included on your projector CD-ROM. You’ll also need to enter a trap IP address as described on page 36. This feature is intended for use by network administrators only.
Using EMP Monitor Before using EMP Monitor, make sure you’ve installed the program as described in Appendix A or on the Quick Setup sheet. The computer you’re using to monitor the projector also has to be set up to communicate with the projector over an 802.11b network, as described in Chapter 3. Opening and Closing EMP Monitor To open the program, select EMP Monitor from the Start menu. If you’ve added the program to the Startup programs folder (see page 89), then it may already be open.
You see this screen: Click here 3. Click Auto detect to locate projectors currently operating on the network. Or click Manual registration and enter the projector’s name and network address. Any projectors found on the network are listed as shown below: Click here 4. Select the projectors you want to add by clicking their name. Then click Add and click Close.
You see any registered projectors listed on the main EMP Monitor screen: Monitoring and Controlling Your Projectors The EMP Monitor screen lets you monitor your projectors using the Status and Video Source icons shown below. This lets you see which projectors are currently being used and to which sources they are connected. Control buttons Status icon note Some of the control buttons are for selecting video sources not used by this model.
If a problem occurs with a projector, an error icon appears as shown below: Error icon For detailed status information, select the projector in question and click View details. Configuring the Monitoring Interval You can select how often EMP Monitor checks the projector status: 1. From the Tool menu, select Configuration. You see this screen. note If you want the program to run whenever you start your computer, click Add to Startup. 2. Select the desired update interval and click OK.
Using a Browser to Monitor Your Projector If your projectors are set up to communicate over an 802.11b network as described in Chapter 3, you can use a standard web browser—such as Microsoft Internet Explorer or Netscape® Navigator®—to monitor and control each one. 1. Do one of the following: ■ Open a web browser and enter the IP address of the projector you want to monitor in the browser window. If you’re not sure what address the projector is using, turn it on and switch it to EasyMP. With the EPSON 802.
■ If you’ve installed the EMP NS Connection software, open it and connect to the projector you want to monitor. Then click on the control bar that appears on the screen. Click here to open browser The projector’s web screen opens in the browser window, as shown below: Main menus Functions corresponding to remote control buttons 2. Select one of the main menu options listed on the left, then change any settings as needed in the main part of the screen.
92 Remotely Monitoring the Projector
1 Maintaining the Projector Y our projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lenses whenever you notice dirt or dust on the surface. ■ Use a canister of compressed air to remove dust. ■ To remove dirt or smears on the lenses, use lens-cleaning tissue. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface. Remove the cap before cleaning Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord.
Cleaning and Replacing the Air Filter Clean the air filter on the side of the projector after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. To clean the air filter, follow these steps: 1. Turn off the projector, allow it to cool down, and unplug the power cord. 2. To clean the filter, EPSON recommends using a small vacuum cleaner designed for computers and other office equipment.
Replacing the Lamp The projection lamp typically lasts for about 1500 hours of use. It is time to replace the lamp when: warning Let the lamp cool fully before replacing it. In the unlikely event that the lamp has broken, small glass fragments may be present and should be removed carefully to avoid injury. ■ The projection image gets darker or starts to deteriorate. ■ The lamp warning light ■ The message LAMP REPLACE appears on the screen when the lamp comes on (after about 1400 hours of use).
4. Use a screwdriver to loosen the two silver screws holding the lamp in place. (You can’t remove these screws.) 5. Grasp the lamp as shown and pull it straight out. caution Do not touch the glass portion of the new lamp assembly. Touching the glass could result in premature lamp failure. 6. Gently insert the new lamp. 7. Once the lamp is fully inserted, tighten its screws. 8. Replace the lamp cover. (The projector won’t come on if the lamp cover is loose.
Resetting the Lamp Timer After you replace the lamp, you need to reset the lamp timer using the projector’s menu. 1. Press the Menu button on the remote control. You see the main menu. 2. Use the arrow buttons on the remote control to highlight About. You see the lamp usage hours and other settings: Lamp usage 3. Press Enter to select the About menu. 4. Select Reset Lamp Timer, then press Enter. You see this prompt: 5. Select Yes, then press Enter. 6. When you’re finished, press Esc or Menu to exit.
Transporting the Projector The projector contains many glass and precision parts. If you need to transport it, follow these packing guidelines to prevent damage to the projector: ■ When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.
100 Maintaining the Projector
1 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue ? Help button on top of the projector or on the remote control. The following choices are available: ■ Help for the image ■ Help for the sound ■ Language selection (Language) Follow these steps to get help: 1. Press the blue ? Help button on the projector. Help button on projector You see the Help menu: doesn't 2.
What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. Power light Lamp/temperature light If the projector is not working correctly, first turn it off, let it cool, and unplug it. Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the status lights on top of the projector and try the solutions recommended on the following pages.
Status lights Light Status Description flashing orange The projector is too hot. Make sure the temperature surrounding the projector does not exceed 95 °F (35 °C) and there is plenty of space around and under the projector for ventilation. The air filter may be clogged. Clean or replace it as described on page 95. red The projector is overheating, which turns the lamp off automatically. Wait until the cooling fan stops, then unplug the power cord.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the P power light is green, not flashing, and the lens cap is off. ■ The projector may be in sleep mode. If the P power light is orange, press the Power button to turn the projector on. ■ If the power was switched off and then on again, the projector may still be cooling down. Wait until the power light stops flashing and remains orange; then press the Power button again.
If you’re using a PC laptop: ■ Hold down the Fn key on the keyboard and press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your laptop’s manual or online help for details. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
The message Not Supported is displayed. ■ Make sure the correct Input Signal is selected in the Video menu (see page 77). ■ Make sure your computer’s resolution doesn’t exceed UXGA (1600 × 1200), and the frequency is supported by the projector (see page 122). If necessary, change your computer’s resolution setting as described on the following page. Only part of the computer image is displayed. ■ Press the Auto button on the remote control.
The image contains static or noise. ■ Make sure the correct Input Signal is selected in the Video menu (see page 77). ■ If you’re using a computer cable longer than 6 feet (2 meters), or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables away from the power cord as much as possible to prevent interference. ■ The video signal may be split between the computer and the projector.
You see vertical stripes or the image still looks blurry after trying the solutions in the previous section. ■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice one or more vertical stripes or bands, or some of the characters may look heavy or blurred. Press the Auto button on the remote control. This resets the projector’s tracking and sync settings.
The colors of the image are not right. note Because of the different technologies used, your projected image may not exactly match the colors on your laptop or computer monitor. ■ If you’re displaying a computer image, use the Color Mode option in the projector’s Video menu to adjust the color. If you’re displaying video, adjust the Color, Tint, and Color Mode settings on the Video menu. ■ Try changing the Color Adjustment setting on the Advanced menu.
Solving EasyMP Problems An image displayed with EasyMP appears distorted. Because of their resolution, some JPEG images cannot be displayed correctly. Some JPEG files from digital cameras cannot be previewed. Files with a high compression ratio may appear blurry. In EMP SlideMaker, some PowerPoint files don’t appear in the file window. EMP SlideMaker does not support PowerPoint 95. Files created in this version of PowerPoint must be opened and resaved in PowerPoint 97 or later.
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. ■ If you’re using the remote control for the first time, be sure to remove the protective tape from the battery tray as shown on page 22. ■ The remote control’s battery may not be installed correctly or may be low on power. To change the battery, see page 23. ■ Make sure you are within 20 feet (6.
Where To Get Help EPSON provides technical assistance through electronic support services 24 hours a day, as listed in the following table. Service Access World Wide Web From the Internet, you can reach EPSON’s product support page at http://support.epson.com. After selecting your product, you can access troubleshooting information, download product documentation, and receive technical advice through e-mail.
114 Solving Problems
A Appendix A: Software Installation T he EasyMP software CD-ROM includes the software you need to use the projector’s EasyMP features—for presenting over a wireless network, transferring PowerPoint presentations to a memory card, and monitoring the projector from a remote location. System Requirements note The EasyMP software cannot be installed on Macintosh systems. Before you install the software, make sure your computer meets these requirements: ■ Microsoft® Windows 98, 2000, Me, or XP ■ 802.
Follow these steps: 1. Insert the EasyMP software CD-ROM in your computer’s CD-ROM drive. You see this screen: Click here 2. Click the button to advance to the next screen. 3. If you want to be able to project over a wireless network (Chapter 3), make sure the option to install EMP NS Connection is highlighted, then click the button. Follow the instructions on the screen to finish installing it. 4.
A Appendix B: Projector Installation T his appendix provides guidelines on installing the projector in a permanent location, such as a theater or conference room.
note See page 8 for more information on projector placement. the distortion by using the Keystone function in the projector’s menu system (see page 80) or by using the Keystone buttons on the projector’s control panel. If you place the projector’s lens so it’s level with the top of the screen, the image will be square and you won’t have to adjust it. If you place the lens lower than the top of the screen, you’ll have to tilt the projector upward if you want to fill the whole screen with the image.
A Appendix C: Technical Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels Diagonal: 0.9 inches (22.9 mm) Lens F=1.9 to 2.1, f=31 to 36 mm Resolution (native format) 1024 × 768 pixels (XGA) Color reproduction 24 bit, 16.8 million colors Brightness 2000 lumens (ANSI) Contrast ratio 400:1 Image size 30 to 300 inches Projection distance 3.2 to 38.5 feet (0.96 to 11.
Projection Lamp Type UHE (Ultra High Efficiency) Power consumption 150 W Lamp life About 1500 hours Part number V13H010L18 Remote Control Range 20 feet (6 meters) Battery CR2025 lithium Mouse Compatibility Supports USB Dimensions Height 2.75 inches (70 mm), feet retracted Width 10.9 inches (276 mm) Depth 7.5 inches (190 mm) Weight 4.4 lb (1.9 kg) Electrical 120 Rated frequency 50/60 Hz AC Power supply 100 to 120 VAC, 3.1A 200 to 240 VAC, 1.
Environmental Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (-10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Safety United States FCC 47CFR Part 15B Class B (DoC) UL1950 Rev. 3 Canada ICES-003 Class B CSA C22.2 No. 950-95 (cUL) CE Marking Directive 73/23/EEC Directive 89/336/EEC EN 55022, EN 55024 Computer Video Port Pin Assignments The Computer1/Component Video port is a female video RGB, 15-pin micro-D-style connector.
Compatible Video Formats The projector supports NTSC, PAL, and SECAM international video standards, as well as the monitor display formats listed below. To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector; see the following table for compatible formats. As noted below, some images are automatically resized to display in one of the projector’s “native” formats (such as XGA).
Mode Refresh Rate (Hz) Resolution MAC13 MAC16 MAC19—60 MAC19 MAC21 67 75 59 75 75 640 × 480* 832 × 624* 1024 × 768 1024 × 768 1152 × 870* NTSC NTSC 4:3 PAL M-PAL N-PAL PAL—60 SECAM 60 60 50 60 50 60 50 — — — — — — — HDTV (480i) HDTV (480p) HDTV (720p) HDTV (1080i) HDTV (1080i) 60 60 60 60 50 640 × 480* 640 × 480* 1280 × 720* 1920 × 1080* 1920 × 1080* *The image is resized using EPSON’s SizeWise Technology. Pixelworks DNXTM ICs are used in this projector.
124 Appendix C: Technical Specifications
A Appendix D: Notices This appendix includes safety instructions and other important information about your EPSON PowerLite projector. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.
126 Appendix D: Notices ■ Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector. ■ Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel. Opening or removing covers may expose you to dangerous voltages and other hazards.
Remote Control Information You can operate the projector by remote control via a line-of-sight infrared (IR) receiver at the front and rear of the projector. The projector may not respond to remote control commands under the following conditions: ■ There is an object between the remote control IR emitter and the IR receiver on the projector. ■ Ambient light is too bright. ■ Certain types of fluorescent lighting are used. ■ A strong light source shines into the IR receiver.
Declaration of Conformity According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: EPSON AMERICA, INC. 3840 Kilroy Airport Way MS: 3-13 Long Beach, CA 90806-2469 Telephone: (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Warranty Epson America, Inc. Limited Warranty Basic Two-Year Warranty and 90-Day Lamp Warranty What Is Covered: Epson America, Inc.
FOR A PARTICULAR PURPOSE. SOME LAWS DO NOT ALLOW THE EXCLUSION OF IMPLIED WARRANTIES. IF THESE LAWS APPLY, THEN ALL EXPRESS AND IMPLIED WARRANTIES ARE LIMITED TO THE WARRANTY PERIOD IDENTIFIED ABOVE. UNLESS STATED HEREIN, ANY STATEMENTS OR REPRESENTATIONS MADE BY ANY OTHER PERSON OR FIRM ARE VOID. EXCEPT AS PROVIDED IN THIS WRITTEN WARRANTY, NEITHER EPSON AMERICA, INC.
132 Appendix D: Notices
Index A C A/V Mute, 79, 81 A/V Mute button, 24 About menu, 83, 98 Access Point mode, 34 to 42 Access point, checking IP address of, 41 Accessories, 6, 113 Ad Hoc mode, 29 to 33 Advanced menu, 81 to 82 Air filter, cleaning and replacing, 95 Anti-theft device, 6, 9 Aspect ratio, 119 ATA flash cards, 62 Audio adjusting tone, 77 to 78 adjusting volume, 77 to 78 connecting computer, 52 connecting laptop, 49 menu, 77 to 78 problems, troubleshooting, 110 turning off (using A/V Mute), 24 Autorun setting, 63 to 64
D Declaration of Conformity, 128 Default settings, restoring, 75, 84 Desktop adapter, Macintosh, 51 to 52 DHCP, 36, 40 Display order setting, 70 Distance from projector to screen, 8, 119 E EasyMP monitoring projector, 85 to 91 presenting from memory card, 55 to 71 problems, 111 projecting wirelessly, 27 to 46 software, 115 to 116 starting, 12, 28 Electrical specifications, 120 EMP Monitor changing monitoring interval, 89 installing software, 116 using, 86 to 89 EMP NS Connection configuring network for, 29
K Kensington anti-theft device, 6, 9 Keystone correction, 19, 80, 107, 119 Keyword, 31, 36, 43 Monitoring projector EMP Monitor, 86 to 89 HP OpenView, 85 web browser, 90 to 91 Mouse, using remote control as, 53 to 54 L N Lamp number of hours used, 83 replacing, 96 to 98 status light, 103 Lamp timer, resetting, 98 Language setting, 102 Laptop computer connecting to, 50 displaying on, 14, 106 Lens cleaning, 94 specifications, 119 Lights, status, 103 to 105 Logo, saving on projector, 78 to 79 Network card
PrivateLine Support, 3, 113 Problems color, 110 EasyMP, 111 image, 105 to 110 remote control, 112 sound, 110 Projection lamp, see Lamp Projector carrying case, 6, 99 cleaning, 94 connections, see Connecting projector distance from screen, 8, 119 feet, adjusting height with, 18 installing, 117 to 118 lamp specifications, 120 monitoring remotely, 85 to 91 options, 6 positioning, 8 to 9 resolution, 1, 119 specifications, 119 to 121 storing, 99 transporting, 99 troubleshooting, 101 to 110 turning off, 20 turnin
Speaker, specifications, 119 Special effects, adding to slide transitions, 62, 70 Specifications brightness, 1, 119 dimensions, 120 electrical, 120 environmental, 121 general, 119 lens, 119 remote control, 120 resolution, 1, 119 safety, 121 SSID, see ESSID Startup screen, creating, 78 to 79 Status lights, 103 to 105 Stopping action, 25 Storing projector, 99 Support, see Technical support S-Video cable, 5, 48 Switching between users, 45 to 46 Switching picture source, 11 to 13, 24 Synchronization, adjusting,
138 Index
