® EPSON PowerLite 505c/715c Multimedia Projector EPSON ® PowerLite 505c/715c User’s Guide ® EPSON PowerLite 505c/715c Multimedia Projector ® ® User’s Guide CPD-11736 ® ® ® EPSON PowerLite 505c/715c Multimedia Projector
speaker Stop action lens ring Power Freeze memory card light Turn off picture and sound Zoom in or out 3 1 2 Mouse pointer and left mouse button Enter foot release lever Turn remote control on/off 5 Add highlighting effects on screen R/C ON OFF E-Zoom 4 remote control receiver Turn projector on/off A/V Mute Illuminate buttons on remote control Right mouse button Esc memory card slot foot foot release lever focus ring Power Power Freeze foot A/V Mute R/C ON OFF E-Zoom 3 4 2 1
EPSON PowerLite 505c/715c Multimedia Projector ® ® User’s Guide
Important Safety Information WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.
C Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Getting the Most from Your Projector . . . . . . . . . . . . . . . . . Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . Reading This Manual Online . . . . . . . . . . . . . . . . . . . . Getting More Information . . . . . . . . . . . . . . . . . . . . . . Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking the Projector . . . . . . . . . . . . . . . . . .
Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Focusing and Zooming Your Image . . . . . . . . . . . . . . . 25 Adjusting the Height of Your Image . . . . . . . . . . . . . . . 25 Adjusting the Image Shape . . . . . . . . . . . . . . . . . . . . . . 26 Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 27 iv 3 Using the Remote Control . . . . . . . . . . . . . . . . . . . 29 4 Creating Presentations for Your Projector . . .
Creating a Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Creating a Scenario by Drag and Drop . . . . . . . . . . . . . Creating a New Scenario File . . . . . . . . . . . . . . . . . . . . Building a Scenario . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting Up Transitions . . . . . . . . . . . . . . . . . . . . . . . . . Adding Computer Access or Video . . . . . . . . . . . . . . . . Transferring Your Presentation to the Projector . . . . . . . . .
7 Maintaining and Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . 84 Cleaning and Replacing the Air Filter . . . . . . . . . . . . . . . . . 85 Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . .
B C Appendix B: Notices . . . . . . . . . . . . . . . . . . . . . . . . 115 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . Remote Control Information . . . . . . . . . . . . . . . . . . . . . . Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . FCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . 115 117 118 119 Appendix C: Technical Specifications . . . . . . 121 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
W - Welcome The EPSON ® PowerLite® 505c/715c are super-portable projectors that offer up to 1200 ANSI lumens of brightness. From boardrooms to auditoriums, your full-color presentations and videos will be bright and visible even in ordinary room lighting. The new EPSON EasyMP™ feature lets you show a presentation without attaching a computer to the projector. Simply drag and drop your file and download it to the projector’s memory card.
Getting the Most from Your Projector Depending on your presentation, you can take advantage of any or all of these options: ■ Projecting without a computer With the EMP SlideMaker software on your computer, you can create presentations called “scenarios” from your PowerPoint® slides and add a variety of special effects. Then you can run your presentation with the remote control. See Chapters 4 and 5 for instructions.
Using Your Documentation To connect the projector to your laptop and get your presentation running fast, see the Quick Setup sheet that came in your Owner’s Kit. This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it: ■ Warnings must be followed carefully to avoid bodily injury. ■ Cautions must be observed to avoid damage to your equipment. ■ Notes contain important information about your projector.
■ If you hold your mouse pointer over text and the hand changes to an index finger, you can click to jump to a related topic. For more information, see your Acrobat Reader online guide. Getting More Information Need tips on giving presentations? Quick steps for setting up your projector? Here’s where you can look for help: ■ www.presentersonline.com Includes a library of articles covering presentation tips, tricks, and technology.
If you still need help after checking this User’s Guide and the sources listed above, you can use the EPSON PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on the card in your Owner’s Kit. Or take advantage of EPSON’s automated support services 24 hours a day. See page 103 for more information. Registration and Warranty Your projector comes with a basic carry-in warranty and an international warranty that let you project with confidence anywhere in the world.
Unpacking the Projector After unpacking the projector, make sure you have all the parts shown below: EPSON PowerLite 505c/715c CD-ROM (not needed to use your projector) Power Freeze A/V Mute R/C ON OFF E-Zoom 3 4 5 1 2 Enter Esc projector EasyMP CD-ROM (for computer-free presentations) batteries remote control power cord computer cable memory card set (in the projector) dummy card and case PS/2 MOUSE RCA AV cable USB mouse cable PS/2® mouse cable Save all packaging in case you need to shi
Additional Components Depending on how you plan to use the projector, you may need additional components: ■ To transfer presentations directly to the memory card in the projector, you need a standard USB cable. ■ To receive an S-Video signal, you need an S-Video cable. (One is usually provided with your video device.) ■ To receive a component video signal from a VCR or other video device, you need a D-sub 15-pin to 3BNC component video cable (available from EPSON).
Optional Accessories To enhance your use of the projector, EPSON provides the following optional accessories: Product Product number Replacement lamp and air filter ELPLP14 Soft carrying cases: Samsonite® wheeled soft case Slimline soft shoulder bag Notebook/projector soft shoulder bag ATA molded hard shell case ELPKS35 ELPKS31 ELPKS32 ELPKS30 Ceiling mount ELPMB34 Suspension adapter for ceiling mount (1-inch pipe) ELPMBAPS Suspension adapter for ceiling mount (1.
1 Setting Up the Projector This chapter tells you how to set up the projector and connect it to a laptop computer or video source. If you need to connect the projector to a desktop or workstation computer, see Appendix A. Using the EasyMP feature, you can give a presentation directly from the projector, without connecting a computer. See Chapters 2 and 3 for information on using the computer and remote control. Then turn to Chapters 4 and 5 to learn how to use EasyMP.
Positioning the Projector Before connecting the projector, you need to decide where to place it. The location you choose depends on the size of the room and what you are projecting. ■ Place the projector on a sturdy, level surface, between 3.6 and 45.5 feet from the screen. ■ Make sure there is plenty of space for ventilation around and under the projector. ■ Make sure the projector is within 6 feet of a grounded electrical outlet or extension cord.
If you place the projector below the level of the screen, you’ll have to tilt it up by extending the feet as shown. Tilting the projector upward causes the image to lose its square shape, but you can correct the distortion by pressing the Keystone button as described in the next chapter. ideal height If you place the projector level with the bottom of the screen, the image will be square and you won’t have to adjust it.
Connecting to a Laptop Computer note To connect to desktops and other computer systems, see Appendix A. If you have an iBook with an RCA videoout port, follow the instructions for connecting to a video device on page 16. You can connect the PowerLite projector to any computer that has a standard video output (monitor) port, including PC notebook and laptop computers, Macintosh PowerBooks, and hand-held devices.
If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 20 for instructions. Connecting the Cable for Remote Mouse Control note Using the remote control as a wireless mouse lets you click through slideshow-style presentations, such as PowerPoint, from up to 30 feet away (for details, see page 38). This gives you more flexibility in delivering your presentation, since you won’t need to stand near your computer.
4. If necessary, configure your laptop to work with an external mouse. If you don’t need to make any other connections, you can plug in your projector and turn it on. See page 20 for instructions. Amplifying Computer Audio Your laptop probably has its own sound system; however, it may not be adequate for your presentation. If you need more volume or better sound quality, you can connect a computer audio cable to take advantage of the projector’s built-in amplifier and speaker.
Connecting to Video Sources You can connect a DVD player, VCR, camcorder, laser disc player, digital camera, or any other compatible video source to your projector. The projector supports HDTV, NTSC, PAL, and SECAM, and automatically detects the video format. The projector can receive composite video, S-Video, and component video. You can connect the projector to one or two of these video sources at the same time; however, you can only use audio from one source at a time.
Connecting the RCA AV Cable Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Connect the yellow plug on one end of the AV cable to the projector’s yellow Video jack. 2. Connect the other end of the cable to the video-out jack on your video source. RCA AV cable Video jack 3. Connect the AV cable to the left and right Audio jacks on the projector (insert the white plug into the L port and the red plug into the R port). 4.
Connecting S-Video If your video source has an S-Video jack, you can use it to project a higher quality video image. However, you’ll need an S-Video cable, which may be included with your video source, or may be purchased. Before starting, make sure the projector and your DVD player or other video source are turned off. 1. Insert one end of an S-Video cable into the projector’s S-Video connector. 2. Insert the other end into the S-Video output port of your video source. S-Video cable 3.
Connecting Component Video Cables If your video source has component video connectors, you can use them to project a higher quality video image. However, you’ll need a component video cable (D-sub 15-pin to 3BNC), which can be purchased from EPSON (ELPKC19). Before starting, make sure the projector and your DVD player or other video device are turned off. 1. Connect the large end of the component video cable to the projector’s Computer/Component Video port. 2.
2 Using the Projector Once you’ve set up the projector, you’re ready to turn it on, adjust the image, and give your presentation. You can use the built-in EasyMP system to project without connecting to other equipment, as described in Chapter 5. Or, you can connect the projector to a computer or video source, as described in Chapter 1 and Appendix A. Although you can operate the projector without it, the remote control lets you use additional features. See Chapter 3 for instructions on using the remote.
Turning On Your Equipment Make sure your projector (and optional equipment) are set up and connected correctly, as described in Chapter 1 or Appendix A. Then turn on your projector, as described below, followed by any equipment you’ve connected to it. You can turn on your computer and video equipment in any order, but if you have both a computer and video source connected, you may have to switch to the desired source as described on page 23.
4. Squeeze the lens cap tabs and remove the lens cap. caution Squeeze here Do not use the projector with the lens cap in place. The heat generated by the lens can damage the cap. 5. Press the red Power button on top of the projector. Power button power light The power light flashes green as the projector warms up, and the projection lamp comes on in about 30 seconds. The power light stays green.
6. Do one of the following: ■ If you’re presenting without a computer, you may see the EasyMP main screen. Use the Enter button on the remote control to select your presentation, then press Enter to start it. See Chapter 5 for more information. If a presentation starts automatically, you may need to press Enter to change slides. ■ If you’re using a computer, turn it on or restart it. In a few moments, you should see your computer display projected.
■ Press the Source button on top of the projector to select the correct source. (Allow a few seconds for the projector to sync up after pressing the button.) If you’re using a PowerBook: You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps: 1. From the Apple menu, select Control Panels, then click Monitors and Sound. 2. Click the Arrange icon. Click here Drag one monitor icon on top of the other 3. Drag one monitor icon on top of the other.
If you’re using a PC laptop: ■ Hold down the Fn key and press the function key that lets you display on an external monitor. It may have an icon such as or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your laptop’s manual or online help for details. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
Focusing and Zooming Your Image Rotate the focus ring to sharpen the image. lens ring tab focus ring Use the tab to rotate the lens ring and reduce or enlarge the image. You can also change the image size by moving the projector closer to or farther away from the screen. You can use the E-Zoom button on the remote control to zoom in on a portion of the image. See page 33 for instructions. Adjusting the Height of Your Image If the image is too low, you can raise it by extending the projector’s feet. 1.
Adjusting the Image Shape If the projected image isn’t square or has a “keystone” shape, do one or more of the following: ■ If your image looks like or , you’ve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely. ■ If your image looks like or , press the + or — side of the Keystone button to correct the shape of the image. After correction, your image will be slightly smaller.
Shutting Down the Projector When you’ve finished using the projector, follow the recommended procedure to shut it down. This extends the life of the lamp and protects the projector from possible overheating. 1. If you’re using a computer, shut it down first. 2. To turn off the projector, press the red Power button on the projector or remote control. You see a confirmation message. (If you don’t want to turn it off, press any other button.
28 Using the Projector
3 Using the Remote Control The remote control lets you access your projector’s features from anywhere in the room—up to 30 feet away. You can use it to turn the projector on and off, zoom in on a portion of your image, and highlight your presentation. You can also use the remote control for EasyMP presentations without a computer. See Chapter 5 for more information about EasyMP.
Turning On and Using the Remote Control caution When replacing batteries, take the following precautions: Don’t mix old and new batteries. Before using the remote control, you need to install its batteries and turn it on as described below. Installing Batteries ■ Follow these steps to install or replace the batteries: Replace batteries as soon as they run out. If the batteries leak, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately. 1.
Using the Remote Control When using the remote control, stand within 30 feet of the projector. Point the remote control either at the front or back of the projector or at the screen (the projector’s front sensor can detect signals bounced off the screen). ■ Press the button for the function you want to use. See the following pages for instructions. ■ For some functions, you need to use the Enter button like a mouse to navigate on the screen.
Controlling the Picture and Sound You can use the remote control to select your source, adjust the volume, temporarily turn off the picture and sound, freeze the action, zoom in on the picture, or display a picture-in-picture video image. Make sure you have set up your projector and connected any equipment as described in Chapter 1 or Appendix A.
Turning Off the Picture and Sound You can use the A/V Mute button on the remote control to turn off the image and sound and darken your screen. This is useful if you want to temporarily re-direct your audience’s attention without the distraction of a bright screen. ■ To turn off the picture, press the A/V Mute button. The screen goes dark. ■ To turn the image back on, press the button again.
Resizing the Image Some computer images need to be resized to display in the projector’s native format—1024 × 768 pixels (PowerLite 715c) or 800 × 600 pixels (PowerLite 505c). If only part of your computer image is displayed, you can correct it with the Resize button. Power Freeze A/V Mute R/C ON OFF E-Zoom 3 4 2 Press the Resize button on the remote control. The screen image is automatically compressed. ■ Continue pressing the Resize button to pan around the screen in the original resolution.
3. When the window is located and sized the way you want, press the Enter button. The menu disappears, and your video plays on the screen. video window 4. When you’re finished viewing the picture-in-picture, press the P in P button again. The video window disappears. Highlighting Your Presentation You can highlight areas on the screen using the numbered buttons on the remote control.
Using the Pointer note You can use the projector’s Effect menu to select a different pointer. See page 75. You can use the pointer tool to place an arrow anywhere on your screen. 1. To activate the pointer tool, press button 1 on the remote control. A green pointer appears in the upper left corner of the screen. 2. Use the Enter button to move the pointer where you want it. 3. To “paste” the pointer on the screen, press down in the center of the Enter button.
Spotlighting Your Image With the Spotlight tool, you can place a square highlight on part of the screen image. 1. To activate the spotlight tool, press button 3 on the remote control. The screen darkens, and a box of light appears on part of the image. 2. Use the Enter button to move the spotlight where you want it. 3. To remove the spotlight, press Esc. You can change the size of the Spotlight using the Effect menu; see page 75.
Using the Remote Control as a Wireless Mouse When you use the remote control as a wireless mouse, you can control your computer or click through slideshow-style presentations (such as PowerPoint) from up to 30 feet away. This gives you more flexibility, since you won’t need to stand near your computer to change slides, for example. With EasyMP, you can use the remote control to play back and edit presentations on the projector’s memory card. See Chapter 5 for more information.
4 Creating Presentations for Your Projector The projector’s EasyMP feature lets you give a presentation without a computer. Once you install the software, you can drag and drop a PowerPoint file to convert it into a format called a scenario. Then you can download the scenario to the projector’s memory card and run it automatically or with the remote control. Or, you can create a scenario from scratch by combining PowerPoint slides and images using the EMP SlideMaker software on your computer.
Accessing the Memory Card To access the memory card, you can either transfer it to your computer or use a USB cable to access the card in the projector. Use the instructions to do one of the following: ■ Remove the memory card from the projector and insert it in your computer’s PCMCIA slot or PC card reader. ■ Use a USB cable to connect your computer to the projector and install the driver. This lets you transfer your presentation directly to the memory card in the projector.
2. Press the button again. The memory card is released, and you can remove it from the slot in the projector. caution Press the button carefully to avoid breaking it. Make sure the button is pressed in before you store the projector in a carrying case or box. 3. Press the button to insert it in the slot. 4. Insert the card in your computer’s PCMCIA slot or card reader. See your computer documentation if you need instructions.
Accessing the Memory Card Through a USB Cable If your computer has a USB port (and a factory-installed version of Windows 98/Me/2000), you can transfer your scenario to the memory card in the projector. This method is especially useful if you don’t have a PCMCIA slot or PC card reader in your computer. You’ll need a shielded USB “AB” interface cable, available from any computer dealer. Before you can transfer your scenario, you need to install the USB driver from the EasyMP CD-ROM.
Installing EasyMP You must install the software to use the EasyMP features. Before you install EasyMP, make sure the computer you use meets the requirements listed below: System Requirements ■ IBM® compatible with at least a Pentium® 166 MHz processor (Pentium II 300 MHz or higher recommended) ■ Microsoft® Windows 95/98/Me, Windows NT 4.0, or Windows 2000 (USB feature not available with Windows 95 or Windows NT 4.
Creating a Scenario A scenario is a series of slides and/or images that you can present without a computer. The easiest way to create a scenario is to drag and EMP SlideMaker icon on your drop a PowerPoint file on the desktop. The file is converted automatically, and you can download it to the projector. You can also create a scenario from scratch using the EMP SlideMaker software to combine PowerPoint slides and images.
When the conversion is complete, you see your scenario in the EMP SlideMaker window: scenario window At this point, you can insert additional slides or images, create transition effects between slides, and add other features to your presentation. See page 47 for instructions. 3. Click the Save button or choose Save from the File menu. EMP SlideMaker automatically names your scenario SCN0001.sic and creates a folder for it within your \Program Files\EMP SlideMaker folder.
Creating a New Scenario File Use this method when you want to combine slides from several PowerPoint presentations and/or include additional images in your scenario. Make sure the EasyMP software is installed before you start. EMP SlideMaker 1. To start the software, double-click the icon on your computer’s desktop. You see the EMP SlideMaker screen: Scenario window Drive selection box Folder window File window Thumbnail window 2. Choose New from the File menu.
3. Type a name for your scenario. SlideMaker automatically creates a folder with the same name. ■ The default location for the scenario file and folder is in the \Program Files\EMP SlideMaker folder, but you can choose a new location. ■ The background color (black) appears around images that don’t fill the entire screen area. You can choose a new color. 4. Click OK when you’re finished with Scenario Setup. Continue with the instructions in the next section to add slides and build your scenario.
2. Drag and drop the files you want to use into the Scenario window. active cell (yellow) 3. To include individual PowerPoint slides, click the PowerPoint file icon. PowerPoint opens briefly in the background, and the PowerPoint slides appear in the Thumbnail window. Drag the slides from the Thumbnail window: BMP cell (green) PowerPoint cell (pink) JPEG cell (blue) Each slide appears in a numbered “cell” in the Scenario window as you drop it.
If you need to rearrange cells, you can drag and drop them as necessary within the Scenario window. When you have finished adding slides and images to your scenario, you can add transitions and other display settings. See the next sections for instructions. Setting Up Transitions EMP SlideMaker lets you set your slides to advance manually or automatically after a specified period of time. You can also choose from a wide variety of transition effects between slides or cells. 1.
4. Choose how you want to advance to the next cell. ■ If you want to advance manually, click On mouse click. ■ If you want to advance automatically, set the timing in the Automatically after box. You can set any length of time between 1 and 1800 seconds (30 minutes). 5. To add a transition “special effect,” click the Effect box and choose from the list. 6. When you’re finished setting up the transition for the selected cell or cells, click OK. 7. Repeat steps 1 through 6 as necessary. 8.
3. Right-click the control cell and choose Cell Properties from the menu. The Source Control box appears: 4. Select your source: ■ If you want to switch to video rather than a computer source, click Video. ■ If you plan to use the S-video connection for the DVD or other source, click S-Video. 5. Choose how you want to advance to the next cell. ■ If you want to advance manually, click On mouse click. ■ If you want to advance automatically, set the timing in the Automatically after box.
Transferring Your Presentation to the Projector Once your scenario is saved, you can transfer it to the memory card. The transfer process converts your scenario from a .SIC file to a .SIT file. Only .SIT files can be played on the projector. note The USB connection is only available on computers with a factory-installed version of Windows 98, Me, or 2000. It is not available with Windows 95 or NT 4.0, and might not work on upgraded systems.
5. Do one of the following: ■ If you don’t want the scenario to run automatically, click No. Skip to step 7 to remove the card and insert it in the projector. ■ If you want it to run automatically, click Yes. Continue with the following instructions.
6. Do one of the following: ■ If the memory card is inserted in the projector, you can begin your presentation as described in Chapter 5. ■ If the card is in your computer, remove it and insert it in the projector to run your presentation. See your computer’s documentation if you need instructions on removing the card. If you’re using Windows 2000 or Me, you first need to click an icon to stop or disconnect the card. Make sure the button below the memory card slot is pressed in.
5 Presenting Without a Computer You can run your presentation from the projector without a computer. You need to start by converting a PowerPoint file into a format called a scenario and downloading the scenario to the projector’s memory card. See Chapter 4 for instructions. Once the scenario is saved on the memory card in the projector, you can run it automatically or with the remote control. You can also rearrange your slides and show images captured from videos or other sources.
Presenting Your Scenario If your scenario is set to autorun, it will start when the projector’s lamp comes on after you press the Power button. If you didn’t change the default settings, each slide will display for 30 seconds. However, you can also display each slide manually, as described on page 57. To change the autorun setting or add transitions, you need to edit your scenario in EMP SlideMaker on your computer.
Two types of icons appear on the screen: ■ EasyMP creates a folder for each scenario on the card. ■ Scenarios always have the .SIT file name extension. 3. Use the Enter button on the remote control to highlight your scenario file (SCN002.SIT, for example). 4. Press Enter. In a moment, your scenario begins. Each slide will display for 30 seconds (unless you have set slides to advance on mouse click). You can press Enter to display the next slide immediately, or press Esc to display the previous slide. 5.
Editing Your Scenario You can modify your scenario using EasyMP on the projector. Some of the things you can do include: ■ Rearranging slides ■ Hiding individual slides ■ Changing the continuous play setting ■ Previewing individual slides ■ Changing the timing between slides Rearranging and Hiding Slides You use the Edit Scenario function to rearrange your presentation or hide individual slides. 1. Press the EasyMP button on the remote control to display the EasyMP main screen. 2.
4. Use the Enter button to highlight Enter to select it. Edit Scenario, then press You see thumbnail images of the slides in your scenario: indicates slide to be moved ■ To move a slide: Use the Enter button to highlight the slide you want to move. Then press Enter. A white line (or “I-beam”) appears to the left of the slide. Use the Enter button to move the highlight where you want the slide to appear. Then press Enter. The slide moves to the new position.
The red non-display icon appears on your slide: hidden slide Select to hide a slide If you change your mind and want to display the slide, repeat the process to remove the non-display icon. 5. Do one of the following: 60 ■ To save your changes, press Esc, then use the Enter button to Return icon. Then press Enter. You return highlight the to the EasyMP main screen. ■ If you don’t want to save your changes, press Esc, then use Cancel icon. Then the Enter button to highlight the press Enter.
Changing the Continuous Play Setting You can set a scenario to repeat continuously or to play through only once. 1. Press the EasyMP button on the remote control to display the EasyMP main screen. 2. Use the Enter button on the remote control to highlight your scenario file. You see a screen like the following: selected scenario Click to set repeat 3. Press the Esc button on the remote control to access the menu icons on the left side of the screen. Options icon, then 4.
Previewing Slides For each folder on the memory card, you can display thumbnails and preview the slides in the folder. 1. Press the EasyMP button on the remote control to display the EasyMP main screen. 2. Use the Enter button on the remote control to highlight the folder for your scenario. 3. Press Esc to access the menu icons on the left side of the screen. 4. To preview all the files, use the Enter button to highlight Preview, then press Enter to select it.
5. Press Esc to access the menu icons. 6. Use the Enter button to highlight display the first slide in the folder. Execute. Press Enter to 7. Press Enter to change to the next slide. Continue pressing Enter to display each slide in sequence. Press Esc if you want to display the previous slide. 8. Press the EasyMP button to end the display. You see a confirmation message. 9. Press Enter to exit. In a moment, you return to the EasyMP main screen.
5. Use the Enter button to select the following settings. After you make your choice for each option, press Enter to enable the change. ■ Continuous Play Determine whether to repeat the display of slides or images in the folder. ■ Screen switching time Set the display time for each slide or image. Choose Advance on Mouse Click if you want to change slides manually. ■ Display order Choose between displaying alphabetically by file name or by image file date.
Capturing Images EasyMP lets you capture any image displayed on the projector and save it on the memory card. You can capture images from video or computer sources. Once you have captured an image or a series of images, you can play them back through EasyMP. Saving Images on the Memory Card You use the projector’s built-in Capture menu to capture and save images on the memory card. Start by displaying the image you want— either from a computer source or a video source such as a VCR or digital camera. 1.
6. When you see the message “This image was saved as CAP_001.JPG in the Memory Card,” press the Menu button to exit the projector menus. Previewing Captured Images Captured images are saved in the CAPTURE folder on the memory card. You can view them and play them back through EasyMP the same as other images on the card. 1. Press the EasyMP button on the remote control to display the EasyMP main screen. 2. Use the Enter button on the remote control to highlight the CAPTURE folder. 3.
You see icons for the images in the folder: 4. To preview an image, use the Enter button to highlight it, then press Enter to display it. To return to the folder display, press Esc. 5. To return to the EasyMP main screen, use the Enter button to highlight the folder icon. Then press Enter. You can also play back your captured images as a slide show and set the playback timing and other options. See pages 62 to 64 for instructions.
68 Presenting Without a Computer
6 Fine-tuning the Projector You can use the projector’s on-screen menus to adjust the image, sound, and other features. You can also create your own startup screen, customize the highlighting tools, and find out how long your lamp has been in use.
Using the Projector’s Menu System The eight projector menus let you adjust and customize the projector features from the remote control: 70 ■ The Video menu controls the look and quality of the projected image. It lets you adjust the image position and fine-tune settings such as Brightness, Sharpness, and Contrast. ■ The Audio menu controls the volume level, treble, and bass settings. ■ The Effect menu lets you change the cursor speed and modify the highlighting tools available on the remote control.
Changing Menu Settings Power You can use the buttons on the remote control to access the menus and change settings. Follow these steps: Freeze A/V Mute R/C ON OFF E-Zoom 1. To display the menu screen, press the Menu button on the remote control. You see the menu screen: 3 4 2 1 5 Enter menu options Esc menus Video Audio Effect Setting Capture Advanced About Reset All :Select Position Tracking Sync.
Adjusting the Image The Video menu lets you make adjustments to the projected image. The options available in the menu depend on which source is selected: standard computer video, EasyMP, composite or S-Video, or component video. Video Audio Effect Setting Capture Advanced About Reset All :Select Position Tracking Sync.
Repositioning the Image Follow these steps to fine-tune the image position: note 1. Press the Menu button. You see the main menu. If you have repositioned the image, you can use the Auto button on the remote control to restore the default settings. 2. Press Enter to select the Video menu. 3. Press Enter to select the Position option. You see the following on the right side of the screen: 4. Use the Enter button to move the image left, right, up, or down. 5.
■ Color (composite video or S-Video only) Adjusts the depth or intensity of the image. ■ Tint (video only) Adjusts the balance of green to magenta in the image. ■ Sharpness Sharpens or softens the image. ■ Gamma Choose Dynamic for computer images with bright colors (such as charts or graphs), Normal for the default, or Natural to enhance video images. ■ Input Signal Leave this setting on RGB when a computer is connected to the Computer/Component Video port.
You see the following: Video Audio Effect Setting Capture Advanced About Reset All :Select Volume Tone Reset : : 0 0 Execute :Enter 3. Press Enter to select the Audio menu. 4. Use the Enter button to set the following options: ■ Volume ■ Tone (treble/bass balance) 5. When you’re finished adjusting the sound, press Esc or Menu. Customizing the Highlighting Tools The highlighting tools let you add pointers and other types of annotations to your image, as described on pages 35 to 37.
You see the Effect menu: Video Audio Effect Setting Capture Advanced About Reset All :Select 1 Cursor/Stamp 2 Box 3 Spotlight 4 Bar Cursor Speed Reset : Setting Setting Setting Setting L M H Execute :Enter 3. Press Enter to select the Effect menu. 4. Use the Enter button to customize: ■ Cursor/Stamp Lets you define the shape and size for the pointer. For some pointers, you can also define the color and length.
Creating Your Own Startup Screen You can transfer any image on your computer to the projector, and then use it as the screen displayed when the projector is not receiving a signal. You can also set it to be displayed when you press the A/V Mute button, or as a startup screen. The image can be a company logo, slogan, photograph, or any other image you want to use. You can also use the Capture menu to capture and save images on the memory card. See page 65 for instructions.
5. Use the Enter button to select the area of the image you want to use. Once you have selected the entire area, press Enter. 6. When you see the message “Do you use this image?” select Yes and press Enter. If you want to change the area selected, select No, press Enter and repeat steps 4 through 6. You see a message like the one at the left. 7. Use the Enter button on the remote control to select a zoom rate (display size), and then press Enter. 8.
To test your setting, press the A/V Mute button to display your image. Press it again to turn off the image. Customizing Projector Features You can use the Setting menu to disable the projector’s sleep mode, adjust the image shape, and customize several other features. 1. Press the Menu button. 2. Use the Enter button to highlight Setting. You see the features and their settings on the right side: Video Audio Effect Setting Capture Advanced About Reset All :Select Keystone P in P No-Signal Msg.
■ Prompt Turns off the identifying text that appears briefly when you switch from computer input to a video source. ■ A/V Mute Selects the screen color or image to display when you press the A/V Mute button. The logo setting displays an image that you have transferred to the projector. See page 77 for instructions on transferring an image to use for the A/V Mute display. ■ Sleep mode Disables the power management system.
4. Use the Enter button to set the following options: ■ Language Select from nine languages to be used for the projector menus. ■ Startup Screen Turn on to display the image or logo you have captured whenever the projector starts. See page 77 for more information. ■ Color Setting Adjusts the color temperature of the projected image. Select Color Temp. and press Enter to set a temperature between 5000 and 10000 K.
You see the lamp usage hours and computer display settings on the right: note If you access the About menu when the projector display is set to video, you only see the lamp life and the video signal setting. Video Audio Effect Setting Capture Advanced About Reset All Lamp ON Time Video Source Input Signal Frequency SYNC Polarity SYNC Mode Resolution Refresh Rate : : : : : : : : : : 9999 H Computer RGB H 999. 99 KHz V 999. 99 Hz H Positive V Negative Sync On Green 9999x9999 999.
7 Maintaining and Transporting the Projector Y our projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image. warning Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely.
Cleaning the Lens Clean the lens whenever you notice dirt or dust on the surface. ■ Use a canister of compressed air to remove dust. ■ To remove dirt or smears on the lens, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface. Extend the lens and remove the cap before cleaning Cleaning the Projector Case Before you clean the case, first turn off the projector and unplug the power cord.
Cleaning and Replacing the Air Filter Clean the air filter on top of the projector after every 100 hours of use. If it is not cleaned periodically, it can become clogged with dust, preventing proper ventilation. This can cause overheating and damage the projector. To clean the air filter, follow these steps: 1. Turn off the projector, allow it to cool down, and unplug the power cord. 2. Stand the projector on end to keep dust and dirt from falling inside. 3.
4. If you need to replace the filter, use a small screwdriver to pry it off. 5. To install the new filter, first insert the tab, then press down until it clicks in place. Replacing the Lamp note You can check to see how many hours the lamp has been used. See page 81. The projection lamp typically lasts for about 1000 hours of use. It is time to replace the lamp when: ■ The projection image gets darker or starts to deteriorate.
Follow these steps to replace the lamp: 1. Turn off the projector, then unplug the power cord. warning 2. Allow the projector to cool down for at least an hour (if it has been on). Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 3. Turn the projector upside-down to access the lamp compartment. 4. Use a screwdriver to loosen the retaining screw on the lamp cover. (You can’t remove the screw from the cover.
caution Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 7. Gently insert the new lamp. 8. Once the lamp is fully inserted, tighten its screws. 9. Replace the lamp cover and tighten its screw securely. (The projector won’t come on if the lamp cover is loose.) Transporting the Projector note EPSON shall not be liable for any damages incurred during transportation. 88 The projector contains many glass and precision parts.
8 Solving Problems This chapter helps you solve problems with your projector, and tells you how to contact technical support for problems you can’t solve yourself.
Using On-Screen Help If the image doesn’t look right or your audio isn’t working, you can get help by pressing the blue ? Help button on top of the projector or under the cover on the remote control. The following choices are available: ■ Help for the image ■ Help for the sound ■ Language selection Follow these steps to get help: 1. Press the blue ? Help button on the projector or the remote control. You see the help menu. 2.
What To Do When the Lights Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. power light lamp light temperature light If the projector is not working correctly, first turn it off and unplug it. Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the status lights on top of the projector and try the solutions recommended below.
The ■ The projector is in a high-temperature cooling cycle. Make sure the room temperature does not exceed 104 °F and there is plenty of space around and under the projector for ventilation. ■ The air filter may be clogged. Clean or replace it as described on page 85. The 92 Solving Problems temperature light is red. ■ The projector has overheated and turned off. Let the projector cool for a few minutes, then turn it back on.
Refer to the following table for a complete description of the projector’s status lights and their meaning: Status lights Light Status Description orange The projector is in sleep mode. You can unplug it or press the Power button to turn it on. flashing green The projector is warming up. Wait for the image to appear. green The projector is operating normally. flashing orange The projector is cooling down.
Solving Problems with the Image or Sound No image appears on the screen. ■ Check that the power light is green, not flashing, and the lens cap is off. ■ The projector may be in sleep mode. If the power light is orange, press the Power button to turn the projector on. ■ If the power was switched off and then on again, the projector may still be cooling down. Wait until the power light stops flashing and remains orange; then press the Power button again.
If you’re using a PC laptop: ■ Hold down the Fn key and press the function key that lets you display on an external monitor. It may have an icon such as , or it may be labelled CRT/LCD. Allow a few seconds for the projector to sync up after pressing it. Check your laptop’s manual or online help for details. On most systems, the key lets you toggle between the LCD screen and the projector, or display on both at the same time.
Only part of the computer image is displayed. ■ Press the Resize button on the remote control. ■ Make sure the image Position setting is correct on the Video menu. See page 73 for more information. ■ Make sure the Input Signal setting is correct on the Video menu. See page 74 for more information. ■ Make sure your computer’s resolution setting is correct. Ideally, it should be 1024 × 768 to match the projector’s native resolution (800 × 600 on the PowerLite 505c).
The image contains static or noise. ■ If you’re using a computer cable longer than 6 feet, or an extension cable, the image quality may be reduced. ■ Keep your computer and video cables separated from the power cord as much as possible to prevent interference. ■ The video signal may be split between the computer and the projector.
You see vertical stripes or the image still looks blurry after trying the solutions in the previous section. ■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice one or more vertical stripes or bands, or some of the characters may look heavy or blurred. Press the Auto button on the remote control. This resets the projector’s tracking and sync settings.
There is no sound. ■ Try turning up the volume. Press the right side of the Volume button on the remote control. ■ If you’re using a VCR or other video source, make sure the volume is not turned all the way down or muted. Also, make sure the cables are connected correctly, as described in Chapter 1. ■ If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted.
Solving Problems with the Remote Control The projector doesn’t respond to remote control commands. Power Freeze A/V Mute R/C ON OFF E-Zoom 3 4 ■ Make sure the remote control is turned on. ■ Make sure you are within 30 feet of the projector, and within range of the projector’s front or back sensor (approximately 30° to left or right and 15° above or below). ■ The remote control batteries may not be installed correctly or may be low on power. To test the batteries, press the light button.
Solving EasyMP Problems An image displayed with EasyMP appears distorted. Because of their resolution, some JPEG images cannot be displayed correctly. Some JPEG files from digital cameras cannot be previewed. Files with a high compression ratio may appear blurry. In EMP SlideMaker, some PowerPoint files don’t appear in the file window. EMP SlideMaker does not support PowerPoint 95. Files created in this version of PowerPoint must be opened and resaved in PowerPoint 97 or later.
EasyMP Error Messages Error discovered in the EasyMP system or No memory card Insert the memory card all the way into the projector’s card slot. See page 54 for instructions. No displayable file Only the following file types can be displayed from the memory card with EasyMP: Scenario files (.SIT), JPEG files (.JPG), and Bitmap files (.BMP). No files Make sure the memory card is inserted in the projector. Press the EasyMP button on the remote control to update the file display.
Where To Get Help EPSON provides technical assistance through electronic support services and automated telephone services 24 hours a day, as listed in the following table. Electronic support and automated telephone services Service Access World Wide Web From the Internet, you can reach EPSON’s product support page at http://support.epson.com. After selecting your product, you can access troubleshooting information, download product documentation, and receive technical advice through e-mail.
Before you call, please have the following information ready: ■ Product name (EPSON PowerLite 505c/715c) ■ Product serial number (located on the bottom of the projector) ■ Computer configuration ■ Description of the problem You can purchase screens, carrying cases, or other accessories from EPSON at (800) 873-7766 or by visiting www.epson.com (U.S. sales only). In Canada, please call (800) 873-7766 for dealer referral.
A Appendix A: Connecting to Additional Equipment This appendix explains how to connect the projector to a desktop computer or Macintosh, or a high-end workstation.
Installing the Projector The projector can be installed for three different viewing setups: front projection, ceiling mounting, or rear projection onto a semi-transparent screen. To project from overhead, you’ll need to select Ceiling in the projector’s Advanced menu. To project from the rear, select Rear Proj. See page 80 for more information. If you’re ceiling-mounting the projector and you place it above screen level, you’ll have to tilt it down to position the image on-screen.
Before you start, make sure the projector and speakers or PA system are turned off. 1. Connect the cable’s 3.5-mm stereo miniplug to the projector’s Audio Out jack. 2. Connect the RCA plugs to the speaker or PA system. Insert the cable’s red plug into the Audio R jack, and the white plug into the Audio L jack of the external speaker system. Connecting to a PC Desktop Computer You can connect the projector to any IBM compatible PC.
Connecting the Computer Cable 1. Disconnect the monitor cable from the video port on the back of the computer. 2. Connect one end of the computer cable to the projector’s Computer port. 3. Connect the other end of the computer cable to the computer’s video port. 4. Tighten the screws on the connectors.
Connecting the Mouse Cable To use the remote control as a mouse, follow the steps below. You’ll use a different mouse cable, depending on whether your computer has a round PS/2 mouse port or a flat USB port. 1. Connect one end of the appropriate mouse cable to the projector’s Mouse/Com port or the USB port, as shown. connecting PS/2 mouse cable connecting USB mouse cable 2. Disconnect your mouse from the port on the back of your computer and replace it with the other end of the cable.
Connecting the Audio Cable If your presentation includes sound and you want to use the projector’s built-in speakers, you can use a computer audio cable. The required cable (3.5-mm stereo miniplug cable) is available from computer or electronics dealers. 1. Connect one end of the audio cable to the Audio In jack on the projector. Audio In jack audio cable 2. Connect the other end of the audio cable to the speaker or audio out port on the computer’s sound card.
Connecting to a Desktop Macintosh You can connect the projector to any desktop Macintosh. This section includes instructions for the following: ■ Connecting the computer video cable ■ Connecting the mouse cable (if you want to use your remote control as a mouse) ■ Connecting an optional audio cable (if you’ll be projecting with audio) When you connect the projector to a desktop Macintosh, you cannot view your display on the Macintosh monitor.
If it doesn’t fit, you may have to use a Macintosh desktop adapter, which you can buy from EPSON (see page 8). To use the adapter, remove its cover as shown and set its DIP switches according to the resolution you want to use, such as 16-inch mode. See your Macintosh documentation for instructions. Replace the cover and connect the adapter to the free end of the computer video cable. Then plug the cable (with the adapter) into the video port on your Macintosh. 4. Tighten the screws on the connectors.
Connecting the Audio Cable If your presentation includes sound and you want to use the projector’s built-in speakers, you can use a computer audio cable. The required cable (3.5-mm stereo miniplug cable) is available from computer or electronics dealers. 1. Connect one end of the audio cable to the Audio In port on the projector. 2. Connect the other end of the audio cable to the speaker or audio-out jack on the Macintosh.
114 Appendix A: Connecting to Additional Equipment
B Appendix B: Notices This appendix includes safety instructions and other important information about your EPSON PowerLite 505c/715c. Important Safety Instructions Follow these safety instructions when setting up and using the projector: ■ Do not place the projector on an unstable cart, stand, or table. ■ Do not use the projector near water or sources of heat. ■ Use attachments only as recommended. ■ Use the type of power source indicated on the projector.
116 Appendix B: Notices ■ Do not place the projector where the cord can be walked on. This may result in fraying or damage to the plug. ■ Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners. ■ Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating.
■ Do not store the projector outside of the required temperature range (14 to 140 °F) or in direct sunlight for long periods of time. Doing so may cause damage to the case. ■ Do not use the projector with the lens cap in place. The heat generated by the lens may damage the cap. ■ The liquid crystal display panel contains more than 99.99% active pixels. However, 0.01% of the pixels may be missing or constantly illuminated.
Declaration of Conformity According to 47CFR, Part 2 and 15 Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B Personal Computers We: Located at: Tel: EPSON AMERICA, INC. 3840 Kilroy Airport Way MS: 6-43 Long Beach, CA 90806-2469 (562) 290-5254 Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
120 Appendix B: Notices
C Appendix C: Technical Specifications General Type of display Poly-silicon Thin Film Transistor (TFT) Size of LCD panels Diagonal: 0.9 inches (22.9 mm) Lens F=2.0 to 2.2, f=35 to 42 mm Resolution 715c: 1024 × 768 pixels (native format) 505c: 800 × 600 pixels (native format) Color reproduction 24 bit, 16.7 million colors Brightness 715c: 1200 lumens (ANSI) 505c: 1100 lumens (ANSI) Contrast ratio 400:1 Image size 26 to 300 inches Projection distance 3.6 to 45.5 feet (1.1 to 13.
Projection Lamp Type UHE (Ultra High Efficiency) Power consumption 150 W Lamp life About 1000 hours Part number ELPLP14 Remote Control Range 32.8 feet (10 meters) Batteries Alkaline AA (2) Mouse Compatibility Supports PS/2, USB, ADB Dimensions Height 2.8 to 3.4 inches (72 to 87 mm) Width 8.4 inches (213 mm) Depth 10.5 inches (267 mm) Weight 6 lb (2.7 kg) Electrical 122 Rated frequency 50/60 Hz Power supply 100 to 120 VAC, 1.9 A 200 to 240 VAC, 1.
Environmental Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Safety United States FCC Part 15B Class B UL1950 Rev. 3 Canada DOC ICES003 Class B CSA C22.2 No. 950 Rev.
Compatible Video Formats The projector supports NTSC, HDTV, PAL, and SECAM international video standards, as well as the monitor display formats listed below. To project images output from a computer, the computer’s video card must be set at a refresh rate (vertical frequency) that’s compatible with the projector; see the following table for compatible formats. As noted below, some images are automatically resized to display in one of the projector’s “native” formats (such as XGA).
Mode Refresh Rate (Hz) Resolution SXGA2—85 85.002 1280 × 9602 SXGA3—43i 43.436 1280 × 10242 SXGA3—60 60.02 1280 × 10242 SXGA3—75 75.025 1280 × 10242 SXGA3—85 85.024 1280 × 10242 UXGA60 60 1600 × 12003 MAC II 13 66.67 640 × 480 MAC16 75.087 832 × 6241 MAC19—60 59.28 1024 × 7681 MAC19 74.93 1024 × 7681 MAC21 75.062 1152 × 8702 HDTV525I 59.94 640 × 4802 HDTV525P 59.94 640 × 4802 HDTV750P 60 1280 × 7202 HDTV1125I 60 1920 × 10802 HDTV71125I 50.
Computer Video Port Pin Assignments The Computer port is a female video RGB, 15-pin micro-D-style connector. Here are its pin assignments: 126 Pin no.
Index A A/V Mute button, 33, 78 A/V Mute setting, 80 About menu, 70, 81 Accessories, 8, 104 Adapters, Macintosh, 8, 111 to 112 Adobe Acrobat Reader, 3 to 4 Advance setting, 49 to 50, 63 to 64 Advanced menu, 70, 80 to 81 Air filter, cleaning and replacing, 85 Anti-theft device, 8, 11 Aspect ratio, 121 ATA flash cards, 41 Audio adjusting tone, 74 to 75 adjusting volume, 32, 74 to 75 cables, 6 connecting desktop, 110, 113 connecting laptop, 14 connecting video device, 16 to 18 menu, 70, 74 to 75 outputting to
Contrast setting, 73 Cursor speed, setting, 76 Cursor/Stamp tool customizing, 76 using, 36 D Declaration of Conformity, 118 Default settings, restoring, 71, 82 Desktop adapter, Macintosh, 111 to 112 Desktop computer, connecting to, 107 to 113 Digital camera, connecting to, 15 to 18 Display order setting, 63 to 64 Display/Hide icon, 59 Distance from projector to screen, 10, 121 Drawing on the screen, 35 to 37 DVD player, connecting to, 15 to 18 E EasyMP button, 32, 56 CD-ROM, 42, 43 creating presentations,
Image adjusting, 24 to 26, 72 to 74 capturing and saving in projector, 77 capturing and saving on memory card, 65 to 67 correcting shape of, 26, 79, 96 focusing, 25 height, adjusting, 25 positioning, 25, 73 previewing captured, 66 to 67 problems with, troubleshooting, 94 to 98 raising, 25 resizing, 34 shape, correcting, 26, 79, 96 size and projection distance, 10 size range, 121 turning off (using A/V Mute), 33 zooming, 25, 33 Input signal setting, 74 Installing EasyMP, 43 USB driver, 42 Installing projecto
O Options for projector, 8 Options icon, 61, 63 P P in P (picture in picture) button, 34 to 35 PC card adapter, 41 reader, 41, 52 PCMCIA slot, 41, 52 Picture See Image Picture-in-picture video source, selecting, 79 Pin assignments, connector, 126 Pointer tool customizing, 76 using, 36 Positioning image, 25, 73 Positioning the projector, 10 to 11, 106 Power button, 21 consumption, 122 saving, 27, 80 status light, 91, 93 supply, 122 PowerBook, connecting to, 12 to 14 PowerPoint files adding slides to a scena
Remote control EasyMP, using for, 38 light button, 30 numbered buttons, 35 problems, 100, 117 specifications, 122 troubleshooting, 100, 117 turning on, 30 using, 29 to 38 wireless mouse, using as, 38 Replacing lamp, 86 to 88 Reset All menu, 70, 82 Resetting menu options, 71, 82 Resize button, 34 Resizing image, 34 Resolution, 1, 121 Return icon, 60, 61 S Safety instructions, 115 to 117 Scenarios adding slides, 47 to 49 background color, 47, 63 to 64 cells, 48 computer access, adding, 50 to 51 Continuous Pl
Startup Screen setting, 81 Startup screen, creating, 77 to 79 Status lights, 91 to 94 Stopping action, 33 Support See Technical support S-Video button, 32 S-Video cable, 7, 15 Sync, adjusting, 73 T Technical support, 4 to 5, 103 to 104 Temperature requirements, 123 status light, 91 Thumbnail slide images, 62 Tint setting, 74 Tone setting, 74 to 75 Tracking, ajusting, 73 Transporting projector, 88 Treble, adjusting, 74 to 75 Troubleshooting EasyMP problems, 101 to 102 image and sound problems, 94 to 99 proj
