PowerLite® 470/475W/480/485W User's Guide
Contents Introduction to Your Projector ................................................................................................................... 9 Projector Features................................................................................................................................ 9 Product Box Contents.................................................................................................................... 10 Additional Components ...........................................
Connecting to a Component-to-VGA Video Source .................................................................. Connecting to a Composite Video Source ................................................................................ Connecting to an S-Video Video Source................................................................................... Connecting to a Video Source for Sound ..................................................................................
Controlling a Networked Projector Using Crestron RoomView...................................................... 65 Using Basic Projector Features ............................................................................................................... Turning On the Projector .................................................................................................................... Turning Off the Projector ......................................................................................
Adjusting Projector Features ................................................................................................................... 95 Shutting Off the Picture and Sound Temporarily ................................................................................ 95 Stopping Video Action Temporarily .................................................................................................... 95 Zooming Into and Out of Images ................................................................
Replacing the Lamp ................................................................................................................ Resetting the Lamp Timer....................................................................................................... Replacing the Remote Control Batteries ..................................................................................... Transporting the Projector.....................................................................................................
Projector Electrical Specifications .................................................................................................... Projector Environmental Specifications............................................................................................ Projector Safety and Approvals Specifications................................................................................. Supported Video Display Formats......................................................................................
Introduction to Your Projector Refer to these sections to learn more about your projector and this manual. Projector Features Notations Used in the Documentation Where to Go for Additional Information Projector Part Locations Projector Features The PowerLite 470/475W/480/485W projectors include these special features: Ultra short throw projection system • Project an 80-inch (203 cm) image (16:10) from just 7.
• Port for connecting an external monitor • Port for connecting a microphone Innovative display and operation features • Low total cost of ownership with long-life projector lamp and high-efficiency air filter • High digital zoom ratio for larger images in shorter projection distances • 3000:1 contrast ratio and Auto Iris control for sharp, detailed images • Built-in closed captioning decoder • Powerful 16 W speaker system with audio out port for connecting external speakers • Epson's Instant Off and Direct
1 Projector 2 Wall mount (setting plate) 3 Remote control 4 Remote control batteries (two AA alkaline) 5 Power cord 6 VGA computer cable 7 Projector documentation CD-ROM 8 Projector feet 9 Password Protected sticker 10 Projector software CD-ROM Parent topic: Projector Features Related concepts Projector Connections 11
Additional Components Depending on how you plan to use the projector, you may need to obtain the following additional components: • To receive an S-Video signal, you need an S-Video cable compatible with your device. See your local computer or electronics dealer for purchase information. • To receive a component video signal, you need a D-sub, 15-pin, component-to-VGA video cable. You can purchase one from Epson or an authorized Epson reseller. • To receive an HDMI signal, you need a compatible HDMI cable.
Option or part Part number PowerLite Pilot (ELPCB01) V12H443020 Wireless Pendant Microphone (ELPMC02) V12H4430M2 Active speakers (ELPSP02) V12H467020 On Wall Cable Management Kit ELPCK01 Kensington security lock ELPSL01 Accolade Duet portable projector screen ELPSC80 ES-3000 Ultra portable projector screen (ELPSC26H) V12H002S3Y ES-1000 portable screen V12H002S4Y Component-to-VGA video cable (ELPKC19) V12H005C19 1-Year Extended Depot Repair Service Plan EPPFTPA1 1-Year Extended Exchange
• Notes contain important information about your projector. • Tips contain additional projection information. Parent topic: Introduction to Your Projector Where to Go for Additional Information Need quick help on using your projector during a presentation? Here's where to look for help: • Built-in help system Press the Help button on the remote control or projector to get quick solutions to common problems. • www.epson.com/support (U.S) or www.epson.
Projector Parts - Front/Top 1 Remote control receiver 2 Speaker 3 Control panel 4 Cable cover screw 5 Cable cover 6 Exhaust vent 7 Lamp cover screw 8 Lamp cover Parent topic: Projector Part Locations 15
Projector Parts - Side 1 Filter cover switch 2 Security cable installation slot 3 Wireless LAN light 4 Obstacle sensor 5 Remote receiver 6 Projection window 7 Security lock port 8 Air filter cover 9 Air intake vent (air filter) 16
10 Focus lever Parent topic: Projector Part Locations Projector Parts - Interface Panel 1 Optional wireless LAN unit slot 2 Audio1 port 3 Audio2 port 4 Computer1 port 5 Computer2 port 6 Monitor Out port 7 Network (LAN) port 8 USB-A port 9 USB-B port 10 HDMI port 11 RS-232C port 12 Audio Out port 13 Power inlet 14 L-Audio-R audio ports 17
15 Video port 16 S-Video port 17 Mic (microphone) port Parent topic: Projector Part Locations Projector Parts - Base 1 Ceiling mount holes (3) 2 Security cable attachment point 3 Rear foot attachment holes (2) 4 Wall mount plate holes (5) 5 Front foot attachment hole 18
Parent topic: Projector Part Locations Projector Parts - Control Panel 1 Projector status lights 2 Source Search button (searches for connected video sources) 3 Enter button (selects options) 4 Horizontal/Vertical keystone adjustment buttons (display the adjustment screen) and arrow buttons 5 Help button (accesses projector help information) 6 Esc button (cancels/exits functions) 7 Wide/Tele buttons (adjust projected image size), horizontal keystone adjustment buttons (adjust screen shape), a
Projector Parts - Remote Control 1 Power button 20
2 Computer button (cycles through connected computer sources) 3 Video button (cycles through connected video sources) 4 Numeric buttons (enter numbers) 5 Auto button (automatically adjusts position, tracking, and sync settings) 6 Aspect button (selects the image aspect ratio) 7 Num button (when held down, switches numeric buttons to number function) 8 Menu button (accesses projector menu system) 9 Arrow buttons (move through on-screen options and control wireless mouse functions) 10 Enter b
Setting Up the Projector Follow the instructions in these sections to set up your projector for use. Projector Placement Installing the Projector Feet Removing and Attaching the Cable Cover Projector Connections Installing Batteries in the Remote Control Projector Placement Your ultra-short throw projector is designed to be installed on a wall . You can also place the projector on a flat surface such as a desk or table to project in a portable setup.
Mounted on the wall or ceiling and projecting from behind a translucent screen Front projection from a table or portable cart 23
Rear projection from a table or portable cart behind a translucent screen Wherever you set up the projector, make sure to position it squarely in front of the screen, not at an angle. If you project from a table or portable cart, or from the rear, be sure to select correct Projection option in the projector's menu system.
Diagonal image size Min. ceiling height Image width Image height Min. projection distance Distance from top of image to wall plate 56 inches 80 inches (202.1 cm) 44.8 inches (113.9 cm) 33.6 inches (85.3 cm) 2.5 inches (6.3 cm) 6.0 inches (15.2 cm) 60 inches 82 inches (209.1 cm) 48 inches (122.0 cm) 36 inches (91.4 cm) 3.5 inches (8.9 cm) 6.4 inches (16.1 cm) 70 inches 89 inches (226.9 cm) 56.0 inches (142.2 cm) 42 inches (106.7 cm) 6.1 inches (15.6 cm) 7.3 inches (18.
Diagonal image size Min. ceiling height Image width Image height Min. projection distance Distance from top of image to wall plate 85 inches 98.1 inches (249.2 cm) 74.1 inches (188.2 cm) 41.7 inches (105.8 cm) 12.1 inches (30.6 cm) 16.5 inches (41.8 cm) 16:10 Aspect Ratio Diagonal image size Min. ceiling height Image width Image height Min. projection distance Distance from top of image to wall plate 53 inches 77.2 inches (196.1 cm) 44.9 inches (114.2 cm) 28.1 inches (71.3 cm) 2.
Diagonal image size Min. ceiling height Image width Image height Min. projection distance Distance from top of image to wall plate 70 inches 85.0 inches (215.9 cm) 59.4 inches (150.8 cm) 37.1 inches (94.2 cm) 4.9 inches (12.4 cm) 7.9 inches (20.1 cm) 80 inches 91.4 inches (232.0 cm) 67.8 inches (172.3 cm) 42.4 inches (107.7 cm) 7.3 inches (18.7 cm) 9.0 inches (22.7 cm) 88 inches 96.4 inches (245.0 cm) 74.6 inches (189.5 cm) 46.6 inches (118.5 cm) 9.3 inches (23.6 cm) 9.8 inches (24.
4:3 Aspect Ratio Diagonal image size Min. ceiling height Image width Image height Min. projection distance Distance from top of image to wall plate 53 inches 78.7 inches (199.8 cm) 42.4 inches (107.7 cm) 31.8 inches (80.8 cm) 2.5 inches (6.2 cm) 6.9 inches (17.4 cm) 60 inches 83.7 inches (212.5 cm) 48 inches (121.9 cm) 36 inches (91.4 cm) 4.4 inches (11.2 cm) 7.7 inches (19.5 cm) 70 inches 90.9 inches (230.8 cm) 56.0 inches (142.2 cm) 42 inches (106.7 cm) 7.2 inches (18.2 cm) 8.
2. Insert the front foot into the hole at the front of the projector. 1 Front foot 2 Rear feet 3. Insert the two rear feet into the holes at the back of the projector. Parent topic: Setting Up the Projector Removing and Attaching the Cable Cover Before you can connect equipment to your projector, you need to remove the cable cover. 1. Remove both of the cable cover screws (screwdriver not included).
2. Slide off the cable cover. To attach the cable cover, slide it into position, then tighten the screws. Parent topic: Setting Up the Projector Projector Connections You can connect the projector to a variety of computer, video, and audio sources to display presentations, movies, or other images, with or without sound. • Connect any type of computer that has a USB port, standard video output (monitor) port, or HDMI port.
• For slide shows without a computer, you can connect USB devices (such as a flash drive or camera) or an optional EPSON document camera. Caution: If you will use the projector at altitudes above 4921 feet (1500 m), turn on High Altitude Mode to ensure the projector's internal temperature is regulated properly.
2. Connect the cable to your projector's USB-B port. 3. Connect the other end to any available USB port on your computer. 4. Do one of the following: • Windows 7/Windows Vista: Select Run EMP_UDSE.exe in the dialog box that appears to install the EPSON USB Display software. • Windows XP: Wait as messages appear on your computer screen and the projector installs the EPSON USB Display software on your computer. • Windows 2000: Select Computer, EPSON_PJ_UD, and EMP_UDSE.
2. Connect the VGA computer cable to your computer's monitor port. 3. Connect the other end to a Computer port on the projector. 4. Tighten the screws on the VGA connectors. Parent topic: Connecting to Computer Sources Connecting to a Computer for HDMI Video and Audio If your computer has an HDMI port, you can connect it to the projector using an optional HDMI cable.
Parent topic: Connecting to Computer Sources Connecting to a Computer for USB Mouse Control If you connected your computer to a Computer, USB-B, or HDMI port on the projector, you can set up the remote control to act as a wireless mouse. This lets you control computer presentations at a distance from your computer. To do this, connect the projector to your computer using a USB cable, if it is not connected already. 1. Connect the USB cable to your projector's USB-B port. 2.
2. Connect the other end to the Audio port that corresponds to the Computer port you are using. Parent topic: Connecting to Computer Sources Connecting to Video Sources Follow the instructions in these sections to connect video devices to the projector.
2. Connect the other end to the projector's HDMI port. Parent topic: Connecting to Video Sources Connecting to a Component-to-VGA Video Source If your video source has component video ports, you can connect it to the projector using a componentto-VGA video cable. Depending on your component ports, you may need to use an adapter cable along with a component video cable. 1.
Related references Input Signal Settings - Signal Menu Connecting to a Composite Video Source If your video source has a composite video port, you can connect it to the projector using an optional RCA-style video or A/V cable. 1. Connect the cable with the yellow connector to your video source's yellow video output port. 2. Connect the other end to the projector's Video port.
Parent topic: Connecting to Video Sources Connecting to a Video Source for Sound You can play sound through the projector's speaker system if your video source has audio output ports. If you are projecting video using a Computer port, connect the projector to the video source using an optional stereo mini-jack audio cable or an RCA audio cable. If you are projecting video using the Video or S-Video port, connect the projector to the video source using an RCA audio cable. 1.
2. Connect the external monitor's cable to your projector's Monitor Out port. Parent topic: Projector Connections Connecting to External Speakers To enhance the sound from your presentation, you can connect the projector to external speakers with built-in amplifiers. You can control the volume using the projector's remote control. If you want to output audio from the external speakers when the projector is turned off, you need to adjust the Standby Setup settings in the projector's Extended menu.
4. Connect the stereo mini-jack end of the cable to your projector's Audio Out port. Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Connecting a Microphone You can connect a microphone to the projector's Mic port to provide audio support during presentations. Note: If you want to output audio from the microphone when the projector is turned off, you need to adjust the Standby Setup settings in the Extended menu. 1.
Parent topic: Projector Connections Related references Projector Setup Settings - Extended Menu Connecting to External USB Devices Follow the instructions in these sections to connect external USB devices to the projector.
2. Connect the USB cable (or USB flash drive or USB memory card reader) into the projector's USB-A port shown here. Note: Do not connect a USB hub or a USB cable longer than 10 feet (3 m), or the device may not operate correctly. 3. Connect the other end of the cable (if applicable) to your device. Parent topic: Connecting to External USB Devices Related topics Projecting a Slide Show Selecting the Connected USB Source You can switch the projector's display to the source you connected to a USB-A port. 1.
Connecting to a Document Camera You can connect the EPSON DC-06 document camera to your projector's USB-A port to project images viewed by the camera. Note: For additional features supported by software, connect the EPSON DC-06 document camera to your computer instead of the projector. You may be able to connect different EPSON document camera models to your projector's Computer port. See the document camera's manual for instructions. 1. Locate the USB cable that came with the document camera. 2.
1. Open the battery cover as shown. 2. Insert the batteries with the + and – ends facing as shown.
3. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed.
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network. Wired Network Projection Wireless Network Projection Setting Up Projector Network E-Mail Alerts Setting Up Monitoring Using SNMP Controlling a Networked Projector Using a Web Browser Crestron RoomView Support Wired Network Projection You can send images to your projector through a wired network.
1. Connect one end of the network cable to your network hub, switch, or router. 2. Connect the other end of the cable to the projector's LAN port. Parent topic: Wired Network Projection Selecting Wired Network Settings Before you can project from computers on your network, you must select the network settings for the projector using its menu system. Note: Make sure you already connected the projector to your wired network using the LAN port. 1. Turn on the projector. 2. Press the Menu button.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Web Control Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web. • Projector Keyword lets you turn on a security password to prevent access to the projector by anyone not in the room with it.
10. To prevent display of the IP address on the standby screen, turn off IP Address Display. 11. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Parent topic: Wired Network Projection Wireless Network Projection You can send images to your projector through a wireless network. To do this, you must install the optional EPSON 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection.
Projector Network Settings - Network Menu Installing the Wireless LAN Module To use the projector over a wireless network, install the EPSON 802.11b/g/n wireless module in the projector. Do not install any other type of wireless module. Caution: Never remove the module while its indicator light is green or flashing, or while you are projecting wirelessly. You may damage the module or lose data. 1. Turn off the projector and unplug the power cord. 2.
3. Insert the wireless LAN module into the port. 4. Replace the cable cover and tighten the screws. 5. Plug in and turn on the projector. Parent topic: Wireless Network Projection Using Quick Wireless Connection (Windows Only) You can use the optional EPSON Quick Wireless Connection USB key to quickly connect the projector to a Windows computer wirelessly. Then you can project your presentation and remove the key when you are done. 1. Turn on the projector. 2.
You see a projected message that the network information update is complete. 3. Remove the USB key. 4. Now connect the USB key to a USB port on your computer or notebook. Note: In Windows Vista, if you see the AutoPlay window, select Run LaunchU3.exe, then select Allow on the next screen. 5. Follow the on-screen instructions to install the Quick Wireless Connection driver. Note: If you see a Windows Firewall message, click Yes to disable the firewall.
3. Select the Network menu and press Enter. 4. Select Network Configuration and press Enter. 5. Select the Basic menu and press Enter. 6. Select the following basic options as necessary: • Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the PJLink protocol for projector control. • Web Control Password lets you enter a password up to 8 alphanumeric characters long for accessing the projector over the web. • Projector Keyword lets you turn on a security password to prevent access to the projector by anyone not in the room with it.
Wireless LAN Menu Settings Note: See your projector's EasyMP Network Projection Operation Guide for details on selecting these settings.
Setting Options Description IP Settings DHCP (On or Off) Selects DHCP if your network assigns addresses automatically, or turns off DHCP so you can enter the network's IP address, subnet mask, and gateway address as needed IP Address Subnet Mask Gateway Address SSID Display On Selects whether to display the SSID on the network standby screen Off IP Address Display On Selects whether to display the IP address on the network standby screen Off Parent topic: Selecting Wireless Network Settings Manu
Parent topic: Wireless Network Projection Setting Up Wireless Network Security You can set up security for your projector to use on the wireless network. Set up one of the following security options to match the settings used on your network: • WEP encryption • WPA security Note: Check with your network administrator for guidance on entering the correct information. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4.
Parent topic: Wireless Network Projection Wireless Security Menu Settings Settings on the Security menu let you select the type of security and security settings that match the network you are connecting the projector to.
Parent topic: Setting Up Wireless Network Security Setting Up Projector Network E-Mail Alerts You can set up the projector to send you an e-mail alert over the network if there is a problem with the projector. 1. Press the Menu button. 2. Select the Network menu and press Enter. 3. Select Network Configuration and press Enter. 4. Select the Mail menu and press Enter. 5. Turn on Mail Notification. 6. Enter the IP address for the SMTP Server option. Note: Do not use these addresses: 127.x.x.x or 224.0.0.
8. Choose an Address field, enter the e-mail address, and select the alerts you want to receive there. Repeat for up to three addresses. Note: Your e-mail address can be up to 32 alphanumeric characters long. 9. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. Note: If a critical problem causes a projector to shut down, you may not receive an e-mail alert.
4. Select the Others menu and press Enter. 5. Enter up to two IP addresses to receive SNMP notifications, using 0 to 255 for each address field. Note: Do not use these addresses: 127.x.x.x or 224.0.0.0 through 255.255.255.255 (where x is a number from 0 to 255). 6. If available, select the Priority Gateway setting for your network. 7. If your network environment uses an AMX controller, turn on the AMX Device Discovery setting to allow the projector to be detected. 8.
Note: If you want to use a web browser to select settings when the projector is turned off, you need to adjust the Standby Setup settings in the Extended menu. 1. Make sure the projector is turned on. 2. Start your web browser on a computer connected to the network. 3. Type the projector's IP address into the browser's address box and press the computer's Enter key. You see the Web Control screen. 4.
7 Searches for sources 8 Selects the network source 9 Selects the USB Display or USB device source 10 Volume button controls 11 Closed Caption control 6. Select the icon corresponding to the projector function you want to control. Parent topic: Using the Projector on a Network Related references Projector Setup Settings - Extended Menu Crestron RoomView Support If you are using the Crestron RoomView network monitoring and control system, you can set up your projector for use on the system.
3. Select Network Configuration and press Enter. 4. Select the Others menu and press Enter. 5. Set the Crestron RoomView setting to On to allow the projector to be detected. 6. When you finish selecting settings, select Complete and follow the on-screen instructions to save your settings and exit the menus. 7. Turn off the projector, then turn it on again to enable the setting.
3. Select the input source that you want to control in the Sources List box. You can scroll through available sources using the up and down arrows in the box. 4. To control projection remotely, click the on-screen buttons that correspond to the projector's remote control buttons. You can scroll through button options at the bottom of the screen.
Using Basic Projector Features Follow the instructions in these sections to use your projector's basic features.
1. Connect the power cord to the projector's power inlet. 2. Plug the power cord into an electrical outlet. The projector's power light turns orange. This indicates that the projector is receiving power, but is not yet turned on (it is in standby mode). Note: With Direct Power On turned on, the projector turns on as soon as you plug it in. 3. Press the power button on the projector or the remote control to turn on the projector.
If you do not see a projected image right away, try the following: • Turn on the connected computer or video device. • Insert a DVD or other video media, and press the play button (if necessary). • Press the Source Search button on the projector or remote control to detect the video source. Parent topic: Using Basic Projector Features Turning Off the Projector Before turning off the projector, shut down any computer connected to it so you can see the computer display during shutdown.
3. To transport or store the projector, make sure the power light is orange (but not flashing), then unplug the power cord. Caution: To avoid damaging the projector or lamp, never unplug the power cord when the power light is green or flashing orange.
Adjusting the Image Height If you are projecting from a table or other flat surface, and the image is too high or low, you can adjust the image height using the projector's adjustable feet. Make sure the feet have been installed. Caution: Tilting the projector will distort the image shape and may cause difficulty focusing the image. 1. Turn on the projector and display an image. 2. To raise the image, extend the rear feet by rotating them. 3. To lower the image, extend the front foot by rotating it.
4. If the image is tilted, rotate the rear feet to adjust their height. If the projected image is unevenly rectangular, you need to adjust the image shape. Parent topic: Using Basic Projector Features Related concepts Image Shape Related references Projector Feature Settings - Settings Menu Image Shape You can project an evenly rectangular image by placing the projector directly in front of the center of the screen and keeping it level.
1. Turn on the projector and display an image. Note: You can display a pattern to aid in adjusting the projected image using the Settings menu. 2. Press one of these keystone buttons on the control panel to display the Keystone adjustment screen. 3. Press a keystone button on the projector's control panel to adjust the image shape.
Note: The horizontal keystone adjustment buttons are labeled Wide and Tele. After correction, your image is slightly smaller. Note: If the projector is installed out of reach, you can also correct the image shape using the Keystone settings in the projector menus.
3. Select the Settings menu and press Enter. 4. Select the Keystone setting and press Enter. 5. Select the Quick Corner setting and press Enter. Then press Enter again. You see the Quick Corner adjustment screen.
6. Use the arrow buttons on the projector or the remote control to select the corner of the image you want to adjust. Then press Enter. 7. Press the arrow buttons to adjust the image shape as necessary. 8. When you are finished, press Esc.
Parent topic: Image Shape Resizing the Image with the Wide and Tele Buttons 1. Turn on the projector and display an image. 2. To enlarge the image size, press the Wide button on the projector's control panel. 3. To reduce the image size, press the Tele button. Note: If the projector is installed out of reach, you can also adjust the image size using the Zoom setting in the projector menus.
1. Turn on the projector and display an image. 2. Adjust the image size using the Wide and Tele buttons. After you adjust the image size, the Image Shift screen is displayed automatically. 3. Use the arrow buttons on the projector or remote control to adjust the image position. Note: You can also use the Settings menu to adjust the Image Shift. Parent topic: Using Basic Projector Features Related references Projector Feature Settings - Settings Menu Focusing the Image 1.
Parent topic: Using Basic Projector Features Related references Projector Feature Settings - Settings Menu Remote Control Operation The remote control lets you control the projector from almost anywhere in the room, up to 19.7 feet (6 m) away. You can point it at the screen or board, or the front or back of the projector. Make sure that you aim the remote control at the projector's receivers within the angles listed here.
1 19.7 feet (6 m) 2 ± 30º 3 ± 55º 4 ± 60º 5 ± 75º 6 ± 15º Note: Avoid using the remote control in conditions with bright fluorescent lights or in direct sunlight, or the projector may not respond to commands. If you will not use the remote control for a long time, remove the batteries.
Using the Remote Control as a Wireless Mouse You can use the projector's remote control as a wireless mouse so you can control your computer presentation from a distance. 1. Connect the projector to a computer using the projector's USB-B, Computer, or HDMI port to display video. 2. If you connected your computer to the Computer or HDMI port, also connect a USB cable to the projector's USB-B port and to a USB port on your computer (for wireless mouse support). 3. Start your presentation. 4.
Using the Remote Control as a Presentation Pointer You can use the projector's remote control as a pointer to help you call out important information during a presentation. The default pointer shape is an arrow, but you can select an alternative shape using the Settings menu. 1. Press the Pointer button on the remote control. 2. Use the arrow buttons on the remote control to move the pointer on the screen. 3. Press Esc to clear the pointer from the screen.
• Press the button for the source you want on the remote control. If there is more than one port for that source, press the button again to cycle through the sources.
Projection Modes Depending on how you positioned the projector, you may need to change the projection mode so your images project correctly. • Front/Upside Down (default setting) flips the image over top-to-bottom to project upside-down from a wall or ceiling mount. • Front lets you project from a table in front of the screen. • Rear/Upside Down flips the image over top-to-bottom and horizontally to project from the wall or ceiling and behind a translucent screen.
Changing the Projection Mode Using the Menus You can change the projection mode to flip the image over top-to-bottom and/or left-to-right using the projector menus. 1. Turn on the projector and display an image. 2. Press the Menu button. 3. Select the Extended menu and press Enter. 4. Select the Projection setting and press Enter. 5. Select a projection mode and press Enter. 6. Press Menu or Esc to exit the menus.
Parent topic: Using Basic Projector Features Related references Image Quality Settings - Image Menu Changing the Image Aspect Ratio You can change the aspect ratio of the displayed image to resize it. 1. Turn on the projector and switch to the image source you want to use. 2. Press the Aspect button on the remote control. The shape and size of the displayed image changes, and the name of the aspect ratio appears briefly on the screen. 3.
Aspect ratio setting Description Normal Displays images using the full projection area and maintains the aspect ratio of the image. 16:9 Converts the aspect ratio of the image to 16:9. Full Displays images using the full width of the projection area, but does not maintain the aspect ratio. Zoom Displays images using the full width of the projection area and maintains the aspect ratio of the image. Native Displays images as is (aspect ratio and resolution are maintained).
Parent topic: Using Basic Projector Features Related references Image Quality Settings - Image Menu Changing the Color Mode You can change the projector's Color Mode using the remote control to optimize the image for your viewing environment. 1. Turn on the projector and switch to the image source you want to use. 2. If you are projecting from a DVD player or other video source, insert a disc or other video media and press the play button, if necessary. 3.
Color Mode Description Photo Best for still images projected in a bright room sRGB Best for standard sRGB computer displays Blackboard Best for presentations onto a green chalkboard (adjusts the colors accordingly) Whiteboard Best for presentations onto a whiteboard (adjusts the colors accordingly) Dynamic Best for video games in a bright room Parent topic: Color Mode Turning On Auto Iris In certain color modes, you can turn on the Auto Iris setting to automatically optimize the image based on
4. Select the Auto Iris setting and select On. Note: You can turn Auto Iris on or off for each Color Mode that supports the feature. You cannot change the Auto Iris setting when you are using a Closed Caption setting. 5. Press Menu or Esc to exit the menus. Parent topic: Color Mode Controlling the Volume with the Volume Buttons The volume buttons control the projector’s internal speaker system or any external speakers you connected to the projector.
Slideshow Features Supported Slideshow File Types Starting a Slide Show Parent topic: Using Basic Projector Features Related tasks Connecting a USB Device or Camera to the Projector Slideshow Features Your projector's Slideshow feature lets you do the following: • Display individual images • Present a slide show of all images in a folder Parent topic: Projecting a Slide Show Supported Slideshow File Types You can project these types of files using the projector's Slideshow feature.
Parent topic: Projecting a Slide Show Starting a Slide Show After connecting a USB device to the projector, you can switch to the USB input source and start your slide show. Note: You can change the Slideshow operation options or add special effects by highlighting Option at the bottom of the screen and pressing Enter. 1. Press the USB button on the projector remote control. The Slideshow screen appears. 2.
• To display a slide show of all the images in a folder, press the arrow buttons to highlight the Slideshow option at the bottom of the screen and press Enter. Note: If any file names are longer than 8 characters or include unsupported symbols, the file names may be shortened or changed only in the screen display. 4. While projecting, use the following commands to control the display as necessary: • To rotate a displayed image, press the up or down arrow button.
Setting Options Description Sort Order In Ascending Sorts files in first-to-last order In Descending Sorts files in last-to-first order On Displays a slide show continuously Off Displays a slide show one time through Screen Switching Time No Does not display the next file automatically 1 Second to 60 Seconds Displays files for the selected time and switches to the next file automatically Effect Wipe Transitions between images with a wipe effect Dissolve Transitions between images with a
Adjusting Projector Features Follow the instructions in these sections to use your projector's feature adjustments. Shutting Off the Picture and Sound Temporarily Stopping Video Action Temporarily Zooming Into and Out of Images Projector Security Features Creating a User Pattern to Display Shutting Off the Picture and Sound Temporarily You can temporarily turn off the projected picture and sound if you want to redirect your audience's attention during a presentation.
1. Press the Freeze button on the remote control to stop the video action. 2. To restart the video action in progress, press Freeze again. Parent topic: Adjusting Projector Features Zooming Into and Out of Images You can draw attention to parts of a presentation by zooming into a portion of the image and enlarging it on the screen. 1. Press the E-Zoom + button on the remote control. You see a crosshair on the screen indicating the center of the zoom area. 2.
Parent topic: Adjusting Projector Features Projector Security Features You can secure your projector to deter theft or prevent unintended use by setting up the following security features: • Password security to prevent the projector from being turned on, and prevent changes to the startup screen and other settings. • Button lock security to block operation of the projector using the buttons on the control panel. • Security cabling to physically cable the projector in place.
1. Hold down the Freeze button on the remote control until you see the Password Protect menu. This takes about five seconds. 2. Press the down arrow to select Password and press Enter. You see the prompt "Change the password?". 3. Select Yes and press Enter. 4. Hold down the Num button on the remote control and use the numeric buttons to set a four-digit password. The password displays as **** as you enter it. Then you see the confirmation prompt. 5. Enter the password again.
Parent topic: Password Security Types Selecting Password Security Types After setting a password, you see the Password Protect menu. Select the password security types you want to use. If you do not see this menu, hold down the Freeze button on the remote control for five seconds until the menu appears. 1. To prevent unauthorized use of the projector, select Power On Protect, press Enter, select On, press Enter again, and press Esc. 2.
You must enter the correct password to use the projector. 1. Hold down the Num button on the remote control while you enter the password using the numeric buttons. The password screen closes. 2. If the password is incorrect, the following may happen: • You see a "wrong password" message and a prompt to try again. Enter the correct password to proceed. • If you enter an incorrect password several times in succession, the projector displays a request code and a message to contact Epson Support.
Saving a User's Logo Image to Display You can transfer an image to the projector and then display it whenever the projector turns on. You can also display the image when the projector is not receiving an input signal or when you temporarily stop projection (using the A/V Mute feature). This transferred image is called the User's Logo screen. The image you select as the User's Logo can be a photo, graphic, or company logo, which is useful in identifying the projector's owner to help deter theft.
7. Select a zoom percentage and press Enter. You see a prompt asking if you want to save the image as the User's Logo. 8. Select Yes and press Enter. Note: It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished. You see a completion message. 9. Press Esc to exit the message screen. 10. Select the Extended menu and press Enter. 11. Select Display and press Enter. 12.
1. Press the Menu button. 2. Select the Settings menu and press Enter. 3. Select the Control Panel Lock setting and press Enter. 4. Select one of these lock types and press Enter: • To lock all of the projector's buttons, select Full Lock. • To lock all buttons except the power button, select Partial Lock. You see a confirmation prompt. 5. Select Yes and press Enter.
• Use the security slot on the back of the projector to attach a Kensington Microsaver Security system, available from Epson. • Use the security cable attachment point on the projector to attach a wire cable and secure it to a room fixture or heavy furniture. Parent topic: Projector Security Features Creating a User Pattern to Display You can transfer an image to the projector and then display it as a pattern to aid in presentations when you use the Pattern Display feature.
2. Press the Menu button, select the Settings menu, and press Enter. 3. Select the Pattern setting and press Enter. 4. Select the User Pattern setting and press Enter. You see a prompt asking if you want to use the displayed image as a User Pattern. 5. Select Yes and press Enter. Note: It takes a few moments for the projector to save the image; do not use the projector, its remote control, or any connected equipment until it is finished. You see a completion message. 6.
Adjusting the Menu Settings Follow the instructions in these sections to access the projector menu system and change projector settings.
2. Press the up or down arrow buttons to move through the menus listed on the left. The settings for each menu are displayed on the right. Note: The available settings depend on the current input source. 3. To change settings in the displayed menu, press Enter. 4. Press the up or down arrow button to move through the settings. 5. Change the settings using the buttons listed on the bottom of the menu screens. 6. To return all the menu settings to their default values, select Reset. 7.
To change settings for an input source, make sure the source is connected and select that source.
Setting Options Description Auto Iris On Adjusts the projected luminance based on the image brightness when certain Color Modes are selected Off Note: The Brightness setting does not affect lamp brightness. To change the lamp brightness mode, use the Power Consumption setting. Parent topic: Adjusting the Menu Settings Related references Available Color Modes Input Signal Settings - Signal Menu Normally the projector detects and optimizes the input signal settings automatically.
Setting Options Description Auto Setup On Automatically optimizes computer image quality (when On) Off Resolution Auto Normal Sets the input signal resolution if not detected automatically using the Auto option Wide Tracking Varying levels available Adjusts signal to eliminate vertical stripes in computer images Sync.
Setting Options Description Input Signal Auto Specifies the signal type from input sources connected to computer ports RGB Component Auto: detects signals automatically RGB: corrects color for computer/RGB video inputs Component: corrects color for component video inputs Video Signal Auto Various video standards Specifies the signal type from the input sources connected to the video ports Auto: detects signals automatically Aspect See the list of available aspect ratios Sets the aspect ratio (w
Setting Options Description Keystone H/V Keystone Adjusts image shape to rectangular (horizontally and vertically) Quick Corner H/V Keystone: lets you manually correct horizontal and vertical sides Quick Corner: select to correct image shape and alignment using an on-screen display Zoom Varying levels available Adjusts the size of the projected image Image Shift Varying positions available Adjusts the position of the projected image Control Panel Lock Full Lock Controls projector button locki
Setting Options Description Pointer Shape Three shapes available Changes the shape of the remote control pointer feature Power Consumption Normal Selects the brightness mode of the projector lamp ECO Normal: sets maximum lamp brightness ECO: reduces lamp brightness and fan noise, and saves power and lamp life Volume Varying levels available Adjusts the volume of projector’s speaker system or external speakers Mic Input Level Varying levels available Adjusts the volume of the projector's speak
Setting Options Description Pattern Pattern Display Selects various pattern display options Pattern Type User Pattern Test Pattern Pattern Display: lets you display the selected pattern type on the screen to aid in presentation Pattern Type: selects the type of grid or line pattern to display User Pattern: captures a projected screen and saves it as a pattern for display Test Pattern: displays a test pattern to assist in focusing and zooming the image and correcting image shape Parent topic: Adjusti
Setting Options Description Display Messages Selects various display options Display Background Messages: controls whether messages are displayed on the screen Startup Screen A/V Mute Display Background: selects the screen color or logo to display when no signal is received Startup Screen: controls whether a special screen appears when the projector starts up A/V Mute: selects the screen color or logo to display when A/V Mute is turned on Closed Caption Off Controls use of closed captions and se
Setting Options Description Operation Direct Power On Selects various operation options Sleep Mode Direct Power On: lets you turn on the projector without pressing the power button Sleep Mode Timer High Altitude Mode Audio Input Sleep Mode: automatically turns off the projector after an interval of inactivity Sleep Mode Timer: sets the interval for Sleep Mode High Altitude Mode: regulates the projector’s operating temperature at altitudes above 4921 feet (1500 m) Audio Input: specifies the audio in
Setting Options Description Language Various languages available Selects the language for projector menu and message displays (not changed by Reset option) Parent topic: Adjusting the Menu Settings Projector Network Settings - Network Menu Settings on the Network menu let you view network information and set up the projector for monitoring and control over a network.
Setting Options Description Net. Info - Wireless LAN Connection mode Displays wireless network status and details Antenna level Projector Name SSID DHCP IP Address Subnet Mask Gateway Address MAC Address Region Code Net.
Note: Available settings depend on the current input source. The lamp usage timer does not register any hours until you have used the lamp for at least 10 hours.
Event ID Code List Parent topic: Adjusting the Menu Settings Related references Optional Equipment and Replacement Parts Projector Lamp Specifications Event ID Code List If the Event ID option on the Info menu displays a code number, check this list of Event ID codes for the solution to the projector problem associated with the code. Event ID code Cause and solution 0432 The EasyMP Network Projection program did not start. Turn the projector off and then on again.
Event ID code Cause and solution 0894 Communication with unauthorized access point was disconnected. Contact your network administrator. 0898 Failed to acquire DHCP. Make sure the DHCP server is operating correctly. If you are not using DHCP, turn off the DHCP setting in the Network menus. 0899 A communication error has occurred. Try restarting the EasyMP Network Projection program and restarting your projector. If that does not solve the problem, contact Epson for help.
• Network menu items • Lamp Hours • Password • Zoom • Image Shift Parent topic: Adjusting the Menu Settings 122
Maintaining and Transporting the Projector Follow the instructions in these sections to maintain your projector and transport it from place to place. Projector Maintenance Transporting the Projector Projector Maintenance Your projector needs little maintenance to keep working at its best. You may need to clean the projection window and obstacle sensor periodically, and clean the air filter and air vents to prevent the projector from overheating due to blocked ventilation.
• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the projection window. Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the projector lamp may cause a fire. Caution: Do not used canned air, or the gases may leave a residue.
Cleaning the Projector Case Before cleaning the projector case, turn off the projector and unplug the power cord. • To remove dust or dirt, use a soft, dry, lint-free cloth. • To remove stubborn dirt, use a soft cloth moistened with water and mild soap. Do not spray liquid directly on the projector. Caution: Do not use wax, alcohol, benzene, paint thinner, or other chemicals to clean the projector case. These can damage the case. Do not use canned air, or the gases may leave a residue.
2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such as a paintbrush). Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in water, or use any detergent or solvent to clean it. Caution: Do not use canned air, or the gases may leave a residue. 3. If dust is difficult to remove or the air filter is damaged, replace the air filter.
2. Slide the air filter cover switch and open the air filter cover.
3. Pull the air filter out of the projector. Note: Air filters contain polypropylene. Dispose of used air filters according to local regulations.
4. Place the new air filter in the projector as shown.
5. Close the air filter cover.
Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays this information in the projector's menu system.
3. Use the screwdriver included with the replacement lamp to loosen the screw securing the lamp cover. 4. Slide off the lamp cover.
5. Loosen the screws securing the lamp to the projector. The screws do not come all the way out. 6. Lift up the lamp handle and gently pull the lamp out of the projector. Note: The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.
7. Gently insert the new lamp into the projector along the guide rail. If it does not fit easily, make sure it is facing the right way. Press the handle down. Caution: Do not touch any glass on the lamp assembly to avoid premature lamp failure. 8. Tighten the screws to secure the lamp.
9. Replace the lamp cover and tighten the screw to secure it. Note: Be sure the lamp cover is securely installed or the lamp will not come on. Reset the lamp timer to zero to keep track of the new lamp’s usage. Parent topic: Projector Lamp Maintenance Related tasks Resetting the Lamp Timer Resetting the Lamp Timer You must reset the lamp timer after replacing the projector's lamp to clear the lamp replacement message and to keep track of lamp usage correctly.
3. Select the Reset menu and press Enter. 4. Select Reset Lamp Hours and press Enter. You see a prompt asking if you want to reset the lamp hours. 5. Select Yes and press Enter. 6. Press Menu or Esc to exit the menus. Parent topic: Projector Lamp Maintenance Related tasks Replacing the Lamp Replacing the Remote Control Batteries The remote control uses two AA manganese or alkaline batteries. Replace the batteries as soon as they run out. Caution: Use only the type of batteries specified in this manual.
1. Open the battery cover as shown. 2. Remove the old batteries. Warning: If the battery fluid has leaked, wipe it away with a soft cloth and avoid getting the fluid on your hands. If it gets on your hands, wash them immediately to avoid injury. 3. Insert the batteries with the + and – ends facing as shown.
4. Close the battery cover and press it down until it clicks into place. Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat or flame. Keep batteries out of the reach of children; they are choking hazards and are very dangerous if swallowed. Parent topic: Projector Maintenance Transporting the Projector The projector contains precision parts, some of which are glass.
Solving Problems Check the solutions in these sections if you have any problems using the projector. Projection Problem Tips Projector Light Status Using the Projector Help Displays Solving Image or Sound Problems Solving Projector or Remote Control Operation Problems Solutions When Network Alert E-Mails are Not Received Where to Get Help Projection Problem Tips If the projector is not working properly, try turning it off and unplugging it. Then plug it back in and turn it on.
1 Power light 2 Lamp light 3 Temperature light Power light Lamp light Temperature light Status and solution Green Off Off Normal operation. Flashing green Off Off Warming up. Wait for an image to appear. Orange Off Off Standby or sleep mode. Flashing orange Off Off Preparing network monitoring or shutting down. (Wait for the light to remain orange before unplugging the projector.) Flashing red Flashing orange Projector is too hot.
Power light Lamp light Temperature light Status and solution Red Off Red Projector has overheated and turned off. Leave it turned off to cool down for five minutes. • Make sure that the vents and air filter are not clogged with dust or obstructed by nearby objects. • If operating the projector at high altitude, turn on High Altitude Mode. • If overheating continues, replace the air filter. • If the problem persists, unplug the projector and contact Epson for help.
Note: If the lights display a pattern not listed in the table above, turn the projector off, unplug it, and contact Epson for help. Parent topic: Solving Problems Related references Projector Feature Settings - Settings Menu Projector Setup Settings - Extended Menu Where to Get Help Related tasks Cleaning the Air Filter and Vents Replacing the Air Filter Replacing the Lamp Using the Projector Help Displays You can display information to help you solve common problems using the projector's Help system. 1.
Solutions When Only a Partial Image Appears Solutions When the Image is Not Rectangular Solutions When the Image Contains Noise or Static Solutions When the Image is Fuzzy or Blurry Solutions When the Image Brightness or Colors are Incorrect Solutions When There is No Sound or Low Volume Solutions to Microphone Problems Parent topic: Solving Problems Solutions When No Image Appears If no image appears, try the following solutions: • Press the A/V Mute button on the remote control to see if the image was te
Related tasks Unlocking the Projector's Buttons Solutions When Image is Incorrect Using the USB Display Function If no image appears or if the image appears incorrectly using the USB Display function, try the following solutions: • Press the USB button on the remote control. • Make sure the USB Display software has installed correctly. Install it manually if necessary. • With Mac OS X, select the USB Display icon in the Dock or from the Applications folder.
1. Hold down the laptop's Fn key and press the key labelled with a monitor icon or CRT/LCD. (See your laptop manual for details.) Wait a few seconds for an image to appear. 2. To display on both the laptop's monitor and the projector, try pressing the same keys again. 3. If the same image is not displayed by the laptop and projector, check the Windows Display utility to make sure the external monitor port is enabled. (See your computer or Windows manual for instructions.) 4.
• Try adjusting the image position using the Position menu setting. • Press the Aspect button on the remote control to select a different image aspect ratio. • If you zoomed into or out of the image using the E-Zoom buttons, press the Esc button twice to return to a full display. • Check your computer display settings to disable dual display and set the resolution within the projector's limits. (See your computer manual for details.
Solutions When the Image Contains Noise or Static If the projected image seems to contain electronic interference (noise) or static, try the following solutions: • Check the cables connecting your computer or video source to the projector. They should be: • Separated from the power cord to prevent interference • Securely connected at both ends • Not connected to an extension cable • Check the settings on the projector's Signal menu to make sure they match the video source.
• If you are projecting from a computer, press the Auto button on the remote control to automatically adjust the tracking and sync. If any bands or overall blurriness remains, display a uniformly patterned image on the screen and manually adjust the Tracking and Sync settings.
• Check your computer or video source to make sure the volume is turned up and the audio output is set for the correct source. • Check the audio cable connections between the projector and your video source. • Make sure any connected audio cables are labelled "No Resistance". • If you are using a Mac and you do not hear sound from an HDMI source, make sure your Mac supports audio through the HDMI port. If not, you need to connect an audio cable.
Solutions to Projector Power or Shut-Off Problems If the projector does not come on when you press the power button or shuts off unexpectedly, try the following solutions: • Make sure the power cord is securely connected to the projector and to a working electrical outlet. • The projector's buttons may be locked for security. Unlock the buttons or use the remote control to turn on the projector. • The power cord may be defective. Disconnect the cord and contact Epson.
• If you assigned an ID number to the remote control to operate multiple projectors, you may need to check or change the ID setting (feature not available with all projectors). • If you lose the remote control, you can order another one from Epson.
Related references Projector Setup Settings - Extended Menu Projector Network Settings - Network Menu Where to Get Help If you need to contact Epson for technical support services, use the following support options. Internet Support Visit Epson's support website at www.epson.com/support (U.S.) or www.epson.ca/support (Canada) for solutions to common problems with your projector. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.
Parent topic: Solving Problems 153
Technical Specifications These sections list the technical specifications of your projector.
PowerLite 480: Normal Power Consumption mode: White light output 3000 lumens (ISO 21118 standard) Color light output 3000 lumens ECO Power Consumption mode: White light output 1800 lumens (ISO 21118 standard) PowerLite 485W: Normal Power Consumption mode: White light output 3100 lumens (ISO 21118 standard) Color light output 3100 lumens ECO Power Consumption mode: White light output 1800 lumens (ISO 21118 standard) Contrast ratio Image size 3000 to 1 with Auto Iris on and Normal Power Consumption mode Powe
Internal sound system 16 W monaural Noise level 35 dB (Normal Power Consumption mode) 28 dB (ECO Power Consumption mode) Keystone correction angle Vertical: ± 5º Horizontal: ± 5º USB-B port compatibility USB 1.1 and 2.0 compliant for USB display or external mouse USB-A port compatibility One USB 1.1 and 2.
Batteries Two alkaline or manganese AA Parent topic: Technical Specifications Projector Dimension Specifications Height (excluding feet) 5.6 inches (143 mm) Width 14.4 inches (367 mm) Depth 14.8 inches (375 mm) Weight 11.5 lb (5.2 kg) Parent topic: Technical Specifications Projector Electrical Specifications Rated frequency 50/60 Hz Power supply 100 to 240 VAC ±10% PowerLite 470/475W: 2.9 to 1.3 A PowerLite 480/485W: 3.1 to 1.
Power consumption Operating: (220 to 240 V) PowerLite 470/475W: Normal Power Consumption mode: 275 W ECO Power Consumption mode: 215 W PowerLite 480/485W: Normal Power Consumption mode: 300 W ECO Power Consumption mode: 215 W Standby: 0.27 W (Communication Off), 8.
Supported Video Display Formats For best results, your computer monitor or video card resolution should be set to display in the projector's native resolution. However, your projector includes Epson's SizeWise chip that supports other computer display resolutions, so your image will be resized to fit automatically. Your computer's monitor or video card refresh rate (vertical frequency) must be compatible with the projector. (See your computer or video card manual for details.
Display format Refresh rate (in Hz) Resolution (in pixels) TV (NTSC) 60 720 × 480 TV (SECAM) 50 720 × 576 TV (PAL) 50/60 720 × 576 SDTV (480i) 60 720 × 480 SDTV (576i) 50 720 × 576 SDTV (480p) 60 720 × 480 SDTV (576p) 50 720 × 576 HDTV (720p) 50/60 1280 × 720 HDTV (1080i) 50/60 1920 × 1080 VGA 60 640 × 480 SVGA 60 800 × 600 XGA 60 1024 × 768 WXGA 60 1280 × 800 60 1366 × 768 WXGA+ 60 1440 × 900 WXGA++ 60 1600 × 900 WSXGA* 60 1680 × 1050 SXGA 60 1280 × 96
Display format Refresh rate (in Hz) Resolution (in pixels) HDTV (1080p) 24/30/50/60 1920 × 1080 * PowerLite 475W/485W only, when using the Wide option as the resolution setting Parent topic: Technical Specifications USB Display System Requirements Your computer system must meet the system requirements here to use the projector's USB Display software. Requirement Windows Mac Operating system Windows 2000 (Service Pack 4 only) Mac OS X 10.5.x, 10.6.x, or 10.7.
Notices Check these sections for important notices about your projector. Recycling Important Safety Information Important Safety Instructions FCC Compliance Statement Wireless Telegraphy Act Regulations Trademarks Software Copyright Copyright Notice Recycling Epson offers a recycling program for end of life products. Please go to www.epson.com/recycle for information on how to return your products for proper disposal.
Important Safety Instructions Follow these safety instructions when setting up and using the projector: • Do not look into the lens when the projector is on. The bright light can damage your eyes. • Do not place the projector on an unstable cart, stand, or table. • Do not operate the projector on its side, or while tilted to one side. Do not tilt the projector more than 5° forward or back.
• Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector. • If you are using two or more projectors side-by-side, leave at least 2 feet (60 cm) of space between the projectors to allow for proper ventilation. • You may need to clean the air filter and vent. A clogged air filter or vent can block ventilation needed to cool the projector. Do not use canned air, or the gases may leave a residue.
• Before you move the projector, make sure its power is turned off, the plug is disconnected from the outlet, and all cables are disconnected. • Never try to remove the lamp immediately after use because it will be extremely hot. Before removing the lamp, turn off the power and wait at least an hour to allow the lamp to cool completely. • Do not disassemble the lamp or subject it to impacts. • Do not place the source of an open flame, such as a lit candle, on or near the projector.
FCC Compliance Statement For United States Users This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.
Parent topic: Notices Trademarks EPSON®, PowerLite®, Instant Off®, and Quick Corner® are registered trademarks, and EPSON Exceed Your Vision is a registered logomarkof Seiko Epson Corporation. PrivateLine® and Accolade® are registered trademarks; DuetTM is a trademark; and EPSON StoreSM and Extra CareSM are service marks of Epson America, Inc. HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.
The list of GPL Programs • busybox-1.13.4 • iptables-1.4.4 • libgcc1(gcc-4.3.3) • libstdc++-6.0.10 • linux-2.6.27 • patches • udhcp 0.9.8 • uvc rev.219 • wireless_tools 29 • EPSON original drivers The GNU General Public License Version 2 is as follows. You also can see the GNU General Public License Version 2 at http://www.gnu.org/licenses/gpl.html GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright ©) 1989, 1991 Free Software Foundation, Inc.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it. For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modifications to it.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 12.
The hypothetical commands `show w' and `show c' should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than `show w' and `show c'; they could even be mouse-clicks or menu items--whatever suits your program. You should also get your employer (if you work as a programmer) or your school, if any, to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the names: Yoyodyne, Inc.
GNU LESSER GENERAL PUBLIC LICENSE Version 2.1, February 1999 Copyright ©) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed. [This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.
have is not the original version, so that the original author's reputation will not be affected by problems that might be introduced by others. Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder.
GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called "this License"). Each licensee is addressed as "you".
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with. c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License. 11.
by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
2. You can use this software for whatever you want. You don't have to pay us. 3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you've used the IJG code. In legalese: The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose.
config.sub, ltconfig, ltmain.sh). Another support script, install-sh, is copyright by M.I.T. but is also freely distributable. It appears that the arithmetic coding option of the JPEG spec is covered by patents owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used without obtaining one or more licenses. For this reason, support for arithmetic coding has been removed from the free JPEG software.
libpng version 1.2.6, September 12, 2004 , is Copyright (c) 2004 Glenn Randers -Pehrson, and is distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors Cosmin Truta libpng versions 1.0.7, July 1, 2000 , through 1.2.5 - October 3, 2002 , are Copyright (c) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.
For the purposes of this copyright and license, "Contributing Authors" is defined as the following set of individuals: Andreas Dilger Dave Martindale Guy Eric Schalnat Paul Schmidt Tim Wegner The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group 42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc.
zlib This projector product includes the open source software program "zlib" which applies the terms and conditions provided by owner of the copyright to the "zlib". The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. List of zlib programs zlib-1.1.4 License terms of conditions of each program which are provided by owner of the copyright to the "zlib" are as follows.
mDNSResponder-107.6 (only mDNSResponderPosix is used) License terms "Apache License Version 2.0, January 2004" are as follows. Apache License Version 2.0, January 2004 http://www.apache.org/licenses/ TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION 1. Definitions. "License" shall mean the terms and conditions for use, reproduction, and distribution as defined by Sections 1 through 9 of this document.
of electronic, verbal, or written communication sent to the Licensor or its representatives, including but not limited to communication on electronic mailing lists, source code control systems, and issue tracking systems that are managed by, or on behalf of, the Licensor for the purpose of discussing and improving the Work, but excluding communication that is conspicuously marked or otherwise designated in writing by the copyright owner as "Not a Contribution.
from the Work, provided that such additional attribution notices cannot be construed as modifying the License. You may add Your own copyright statement to Your modifications and may provide additional or different license terms and conditions for use, reproduction, or distribution of Your modifications, or for any such Derivative Works as a whole, provided Your use, reproduction, and distribution of the Work otherwise complies with the conditions stated in this License. 5. Submission of Contributions.
To apply the Apache License to your work, attach the following boilerplate notice, with the fields enclosed by brackets "[]" replaced with your own identifying information. (Don't include the brackets!) The text should be enclosed in the appropriate comment syntax for the file format. We also recommend that a file or class name and description of purpose be included on the same "printed page" as the copyright notice for easier identification within third-party archives.
3. the name of the copyright holder is not used to endorse products built using this software without specific written permission. DISCLAIMER This software is provided 'as is' with no explicit or implied warranties in respect of its properties, including, but not limited to, correctness and/or fitness for purpose. newlib This projector product includes the open source software program "newlib" which applies the terms and conditions provided by owner of the copyright to the "newlib".
* Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. * Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
LUCENT DISCLAIMS ALL WARRANTIES WITH REGARD TO THIS SOFTWARE, INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL LUCENT OR ANY OF ITS ENTITIES BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
Copyright (C) 1993 by Sun Microsystems, Inc. All rights reserved. Developed at SunPro, a Sun Microsystems, Inc. business. Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is preserved.
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (12) SuperH, Inc. Copyright 2002 SuperH, Inc.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of KTH nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
(17) S. L. Moshier Author: S. L. Moshier. Copyright (c) 1984,2000 S.L. Moshier Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software. THIS SOFTWARE IS BEING PROVIDED "AS IS", WITHOUT ANY EXPRESS OR IMPLIED WARRANTY.
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. The name of the author may not be used to endorse or promote products derived from this software without specific prior written permission.
results of the use of, the software and documentation in terms of correctness, accuracy, reliability, currentness, or otherwise; and you rely on the software, documentation and results solely at your own risk. IN NO EVENT SHALL INTEL BE LIABLE FOR ANY LOSS OF USE, LOSS OF BUSINESS, LOSS OF PROFITS, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. IN NO EVENT SHALL INTEL'S TOTAL LIABILITY EXCEED THE SUM PAID TO INTEL FOR THE PRODUCT LICENSED HEREUNDER.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS "AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
(32) - Andrey A. Chernov (targets using libc/posix) Copyright (C) 1996 by Andrey A. Chernov, Moscow , Russia . All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. (35) - ARM Ltd (arm and thumb variant targets only) Copyright (c) 2009 ARM Ltd All rights reserved. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1.
* Neither the name of CodeSourcery nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. THIS SOFTWARE IS PROVIDED BY CODESOURCERY, INC. "AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
* from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR * A PARTICULAR PURPOSE ARE DISCLAIMED.
Copyright Attribution Parent topic: Notices A Note Concerning Responsible Use of Copyrighted Materials Epson encourages each user to be responsible and respectful of the copyright laws when using any EPSON product. While some countries' laws permit limited copying or reuse of copyrighted material in certain circumstances, those circumstances may not be as broad as some people assume. Contact your legal advisor for any questions regarding copyright law.
