Installation guide
Table Of Contents
- EM135B2511F Robot System Safety and Installation Read this manual first (RC90/RC+5.0) Rev.6
- PREFACE
- TABLE OF CONTENTS
- 1. Safety 1
- 2. Installation 19
- System Example 20
- 2.1 Outline from Unpacking to Operation of Robot System 21
- 2.2 Unpacking 22
- 2.3 Transportation 23
- 2.4 Manipulator Installation 25
- 2.5 Controller Installation 29
- 2.6 Connection to EMERGENCY Connector (Controller) 31
- 2.7 Power Supply 38
- 2.8 Connecting Manipulator and Controller 40
- 2.9 Power-on 41
- 2.10 Saving Default Status 43
- 3. First Step 44
- 4. Second Step 57
- 5. General Maintenance 59
- 6. Manuals 64
- 7. Directives and Norms 66
- 1. Safety
- 1.1 Conventions
- 1.2 Design and Installation Safety
- 1.3 Operation Safety
- 1.4 Maintenance Safety
- 1.5 Emergency Stop
- 1.6 Labels
- 1.7 Safety Features
- Emergency Stop Switch
- Safety Door Input
- Low Power Mode
- Dynamic Brake
- Motor Overload Detection
- Irregular Motor Torque (out-of-control manipulator) Detection
- Motor Speed Error Detection
- Positioning Overflow -Servo Error- Detection
- Speed Overflow -Servo Error- Detection
- CPU Irregularity Detection
- Memory Check-sum Error Detection
- Overheat Detection at the Motor Driver Module
- Relay Deposition Detection
- Over-Voltage Detection
- AC Power Supply Voltage Drop Detection
- Temperature Anomaly Detection
- Fan Malfunction Detection
- 1.8 Lockout / Tagout
- 2. Installation
- System Example
- 2.1 Outline from Unpacking to Operation of Robot System
- 2.2 Unpacking
- 2.3 Transportation
- 2.4 Manipulator Installation
- 2.5 Controller Installation
- 2.6 Connection to EMERGENCY Connector (Controller)
- 2.7 Power Supply
- 2.8 Connecting Manipulator and Controller
- 2.9 Power-on
- 2.10 Saving Default Status
- 3. First Step
- 4. Second Step
- 5. General Maintenance
- 6. Manuals
- 7. Directives and Norms
1. Safety
Safety and Installation (RC90 / EPSON RC+5.0) Rev.6 3
1.3 Operation Safety
The following items are safety precautions for qualified Operator personnel:
■
Please carefully read the Safety-related Requirements before
operating the robot system. Operating the robot system without
understanding the safety requirements is extremely hazardous and
may result in serious bodily injury and/or severe equipment damage to
the robot system.
■
Do not enter the operating area of the Manipulator while the power to
the robot system is turned ON. Entering the operating area with the
power ON is extremely hazardous and may cause serious safety
problems as the Manipulator may move even if it seems to be stopped.
■
Before operating the robot system, make sure that no one is inside the
safeguarded area. The robot system can be operated in the mode for
teaching even when someone is inside the safeguarded area.
The motion of the Manipulator is always in restricted status (low
speeds and low power) to secure the safety of an operator. However,
operating the robot system while someone is inside the safeguarded
area is extremely hazardous and may result in serious safety problems
in case that the Manipulator moves unexpectedly.
WARNING
■
Immediately press the Emergency Stop switch whenever the
Manipulator moves abnormally while the robot system is operated.
Continuing the operating the robot system while the Manipulator
moves abnormally is extremely hazardous and may result in serious
bodily injury and/or severe equipment change to the robot system.
WARNING
■
Be sure to connect the AC power cable to a power receptacle. DO
NOT connect it directly to a factory power source. To shut off power
to the robot system, pull out the power plug from the power source.
Performing any work while connecting the AC power cable to a factory
power source is extremely hazardous and may result in electric shock
and/or malfunction of the robot system.