TM-H5000II User’s Manual / Bedienungsanleitung Gebruikershandleiding / Manuel d’utilisation Manual do utilizador / Manual del usuario Manuale dell’utente 401406401
Printer Parts 3 4 autocutter cover paper roll cover 5 2 front cover POWER ERROR PAPER OUT paper roll control panel FEED FORWARD 6 1 on/off switch slip paper control panel REVERSE POWER ERROR RELEASE SLIP RELEASE DIP Switch Tables Serial Parallel SW Function ON OFF SW Function ON OFF 1-1 Data receive error Ignored Prints “?” 1-1 Auto line feed Enabled Disabled 1-2 Receive buffer 45 bytes 4 KB 1-2 Receive buffer 45 bytes 4 KB 1-3 Handshaking XON/XOFF DTR/DSR 1-3 ~ 1
English All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein.
English WARNING: Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a SEIKO EPSON service center for advice. Never attempt to repair this product yourself. Improper repair work can be dangerous. Never disassemble or modify this product. Tampering with this product may result in injury or fire. Be sure to use the specified power source.
English Unpacking The following items are included with the standard specification printer. If any item is damaged, contact your dealer. ❏ Printer ❏ Power switch cover ❏ Ribbon cassette ❏ Paper roll ❏ Hexagonal lock screws (2 pcs) (only for the serial interface) Control Panels Paper Roll Control Panel FEED button Press to feed paper one line; hold down to feed continuously. POWER LED Lights when the printer is on. ERROR LED Lights to indicate an error.
English ERROR LED Lights to indicate an error. RELEASE LED Lights to indicate that you can insert slip paper. SLIP LED Lights to indicate that the printer is in slip mode. Removing the Dampers The printer is protected for shipping by two transportation dampers that you must remove before you turn on the 1 printer. Open the printer by pulling the tab on the front cover, and remove the two dampers shown in illustration 1. Note: Reinstall the dampers before shipping.
English CAUTION: Never turn the ribbon cassette’s feed knob in the opposite direction of the arrow marked on the cassette; otherwise the ribbon cassette may be damaged. 1. Turn the printer on, and open the front cover by pulling up the tab on the left side. 2. Be sure the print head is on the right side. 3. If a ribbon is already installed, remove it by grasping the end of the tab and removing it from the printer. 4.
English Inserting Slip Paper Note: Do not use wrinkled or curled paper. 1. When the SLIP LED flashes, insert slip 7 paper, using the right edge of the slip paper inlet as a guide (see illustration 7 ). 2. When you insert the slip into the inlet as 1 far as it will go, the sensor detects the 2 slip, the SLIP LED changes from flashing to on, and the printer draws the paper in and prints it. 3. After printing is complete, the SLIP LED goes off, and you can remove the slip.
English Cleaning the Paper Roll Print Head CAUTION: After printing, the print head can be very hot. Be careful not to touch it and to let it cool before you clean it. Do not damage the print head by touching it with your fingers or any hard object. Turn off the printer, open the paper roll cover, and clean the thermal elements of the print head with a cotton swab moistened with an alcohol solvent (ethanol, methanol, or IPA).
English Troubleshooting No lights on the control panel Check that power supply cables are plugged into the printer correctly, the power unit, and power outlet. The ERROR light is on, and nothing is printing If the PAPER OUT LED is on, paper is not inserted or is not inserted correctly. If the PAPER OUT LED is off, check that the paper roll cover is closed correctly. The ERROR light is flashing, and nothing is printing Check for a paper jam.
English 3. If paper is caught in the automatic cutter in the receipt section and the paper roll cover cannot be opened, open the cutter cover toward you, as shown in illustration 8. 4. Rotate the knob until ▼ appears in the window, as shown in illustration 9. This returns the cutter blade to the normal position. There is a label near the cutter to assist you. 5. Close the cutter cover. 6. Open the paper roll cover and remove the jammed paper.
English TM-H5000II specifications Printing method Slip — Serial impact dot matrix, 9-pin vertical line Receipt — Thermal line printing Printing direction Slip — Bidirectional, minimum distance printing Receipt — Unidirectional with friction feed Characters per line (default) Slip — 9 × 9 font: 66; 7 × 9 font: 88 Receipt — Font A: 42; Font B: 56 Character structure Slip — 9 × 9, 3-dot spacing (half dots); 7 × 9, 2-dot spacing (half dots) Receipt — Font A = 12 × 24, 2-dot spacing; Font B = 9 × 17, 2-d
