® EPSON 14" Super VGA Color Monitor(Models A882441 and A882459) User’s Guide
FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT NOTICE DISCLAIMER OF WARRANTY Epson America makes no representations or warranties, either express or implied, by or with respect to anything in this manual, and shall not be liable for any implied warranties ofmerchantability and fitness for a particular purpose or for any indirect, special, or consequential damages. Some states do not allow the exclusion of incidental or consequential damages, so this exclusion may not apply to you. COPYRIGHT NOTICE All rights reserved.
Important Safety Instructions Although this monitor is designed to assure your safety, improper use can cause electric shock or fire hazard. In order not to defeat the safeguards incorporated in the monitor, observe the following safety instructions: 1. Read all of these instructions and save them for later reference. 2. Follow all warnings and instructions in this manual and marked on the monitor. 3. The monitor contains shock hazard potential.
14. Do not allow anything to rest on the power cord. Do not place a cord where it may be stepped on. 15. Do not replace the video interface cable with a non-shielded cable 16. Unplug the monitor from the computer and the wall outlet before cleaning. Use a damp cloth for cleaning. 17. Excessive brightness for long periods may permanently imprint an image on the screen. 18.
Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Energy Star Compliant . . . . . . . . . . . . . . . . . . . . . 1 Where to Get Help . . . . . . . . . . . . . . . . . . . . . . . . 2 Electronic Support Services . . . . . . . . . . . . . . . . . . 3 Unpacking the Monitor . . . . . . . . . . . . . . . . . . . . . . . 4 Setting Up the Monitor . . . . . . . . . . . . . . . . . . . . . . . 4 Attaching the Tilt and Swivel Base . . . . . . . . . . . . .
Introduction Your EPSON® Super VGA Color Monitor (models A882441 and A882459) is compatible with all IBM® 8514A, VGA, and Super VGA modes from 30 to 50 KHz. It offers the following features: o 14-inch, analog color CRT display with non-glare surface and a 13.
The EPA estimates that if all desktop computers, monitors, printers, and other peripheral devices met Energy Star standards, energy cost savings would exceed $1 billion annually and carbon monoxide emissions would be reduced by 20 million tons. The Energy Star emblem does not represent EPA endorsement of any product or service. Where to Get Help If you purchased your monitor outside the United States, contact an EPSON representative at the nearest marketing location for support and service.
Electronic Support Services If you have a modem, the fastest way to access helpful tips, specifications, drivers, application notes, DIP switch or jumper settings, and bulletins for EPSON products is through the online services below. EPSON bulletin board service You can call the EPSON Bulletin Board Service (BBS) at (310) 782-4531. No membership is required. Make sure your communications software is set to 8 data bits with no stop bit, 1 parity bit, and a modem speed up to 28.8 Kbps.
Unpacking the Monitor When you unpack your monitor, make sure you have these items : o EPSON 14" Super VGA Color Monitor o AC power cord (to connect the monitor to a wall outlet) o Tilt and swivel base o Warranty card o Registration card. If anything is missing or damaged, contact your EPSON representative immediately. Be sure to keep the monitor’s original box and packing materials in case you need to transport the monitor later.
Attaching the Tilt and Swivel Base Before you attach the tilt and swivel base, cover your work area with a blanket or foam pad to avoid scratching the monitor. Then follow these steps: 1. Carefully set the monitor face down on the padding so the bottom of the monitor is facing you. 2. Locate the four sets of hooks on the top portion of the base. 3. Hold the base so the hooks are turned down and position the base next to the bottom of the monitor.
4. Insert the hooks into the slots on the monitor. 5. Slide the base toward the front of the monitor until the base clicks into position. 6. Carefully turn the monitor over so it rests on its base Note Always remove the tilt and swivel base before packing and transporting the monitor. To remove the base, disconnect the power cord from the electrical outlet and disconnect the video interface cable from the back of the computer. Carefully set the monitor face down on a padded surface.
Selecting a Location for the Monitor Follow these guidelines when you select a location for the monitor: o Read the safety instructions at the beginning of this manual. o Use a large, sturdy desk that can support the weight of the computer, monitor, and any peripheral devices. The desk should also provide ample space to hold your equipment and work materials. o For your comfort, it is best to place the monitor directly in front of you and sit about an arm’s length away from it.
Follow these steps to connect the monitor to your computer: 1. Make sure the monitor, computer, and any peripheral devices are turned off. 2. Turn the monitor around so its back is facing you. 3. Plug the end of the video cable into the video connector on the back of the computer and tighten the two screws on the cable connector. 4. Plug one end of the power cord into the monitor’s AC receptacle. Plug the other end into a properly grounded wall outlet.
Turning On the Monitor Turn on the monitor by pressing the power button located at the front right of the monitor. Then turn on the computer. After a few seconds, an image appears on the screen. The power indicator is green when you first turn on the monitor and when the monitor is in the full-power state. When the monitor is in the low-power state, the power indicator is amber.
Accessing the Monitor Controls The image control box contains the image controls for the monitor. It is located at the bottom left of the monitor. To access the controls, you need to open the control box cover. Place your finger at the left side of the cover and pull it gently forward until the cover opens. Adjusting the Monitor Controls The controls on the front of the monitor allow you to adjust the display to suit your preferences.
The following table summarizes the functions of the monitor’s controls. Control Icon Function Vertical center Centers the image vertically. Turn the control clockwise to move the image up: turn it counterclockwise to move the image down. Vertical size Adjusts the vertical size of the image. Turn the control clockwise to increase the height: turn it counterclockwise to decrease the height. Horizontal center Centers the image horizontally.
Cleaning the Monitor To keep the monitor operating at its best, it is important to clean it regularly. Follow these steps: 1. Turn off the monitor and unplug the power cord from the wall outlet. Also disconnect the video interface cable from the computer. 2. Use a damp, lint-free cloth to wipe the monitor casing; do not use a wet cloth. 3. To clean the screen, spray a household glass cleaner on a cloth; then wipe the screen. Caution To avoid electric shock, do not spray cleaner directly on the monitor.
3. The electrical outlet may not be functional. Test the outlet by plugging in a lamp or other device. The power indicator is on, but there is no image on the screen. 1. Make sure the computer is turned on. 2. Make sure the video interface cable is properly connected to the monitor and the video interface on the computer. See “Connecting the Monitor to Your Computer” on page 7. 3. Adjust the contrast and brightness controls. See page 11. 4.
3. The input signals may be outside the monitor’s horizontal and vertical frequency ranges (30 to 50 KHz horizontal and 50 to 90 Hz vertical). Make sure the input signals are within the specified ranges. 4. Make sure your computer’s video adapter is set up for use with the monitor and that any DIP switches or jumpers in the computer or on a video adapter card are set properly. See your computer or video adapter card manual for instructions. The image is not centered or if locks in place on the screen.
Specifications Model Number A882441, A882459 CRT Size 14 inches (356 mm) diagonal Viewing area 13.2 inches (335 mm) diagonal Resolution 1024 x 768, non-interlaced Display area 9.6 x 7.3 inches (245 x 185 mm) Deflection angle 90° Dot pitch 0.28 mm Surface Non-glare tinted Misconvergence 0.35/0.
D-type connectorpin assignments Pin Signal Pin Signal 1 2 3 4 5 6 7 8 Red Green Blue Ground Self test Red return Green return Blue return 9 10 11 12 13 14 15 Not connected Digital GND Ground Not connected H-sync V-sync Not connected Scanning Modes Resolution Vertical frequency 640 x 350 70 Hz 640 x 400 70 Hz 640 x 480 60/72/75 Hz 800 x 600 56/60/72/75 Hz 1024 x 768 interlaced/60 Hz * Interlaced Power Supply Input voltage 16 100-240 VAC, 50/60 Hz, 0.
Display Power Management Environment Requirements Operating temperature 40° F to 85° F (5° C to 35° C) H umidity 8% to 80% noncondensing Safety Standards UL, CSA, FCC-B, DHHS Physical Characteristics Net weight 25 lb (11.3 Kg) Width 14 inches (356 mm) Height 15.3 inches (387 mm) Depth 15.
Epson America (USA) EPSON Connection Tel: (800) 922-8911 EPSON Accessories Tel: (800) 873-7766 Fax: (310) 782-4401 Epson America, Inc. 20770 Madrona Avenue Torrance, CA 90509-2842 Tel: (310) 782-0770 Epson America (lnternational) Epson Latin America Miami, FL, USA Tel: (305) 265-0092 Fax: (305) 265-0097 Epson Mexico, S.A. De C.V. Mexico, D.F., Mexico Tel: (525) 395-9944 Hotline: (91800) 50326 Fax: (525) 395-9499 Epson Argentina, S.A.
EPSON International Marketing Locations Epson Deutschland GmbH Zülpicher Straße 6, 40549 Düsseldorf 11 Germany Tel: (49) (211) 56030 Telex: (41) (211) 504-7787 Epson France S.A. B.P. 320, 68 Bis Rue Marjolin 92305 Levallois-Perret Cedex France Tel: (33) (1) 4087-3737 Telex: (42) 610657 Fax: (33) (1) 4737-2240 Epson Iberica, S.A. Avda. de Roma 18-26 08290 Cerdanyola del valles Barcelona, Spain Tel: (34) (3) 582-1500 Fax: (34) (3) 582-1555 Telex: 50129 Epson Italia s.p.a. V.le F.
Distributors South America SISCO São Paulo, SP Brazil Tel: (5511) 549-4846 Fax: (5511) 549-4571 Siser Ltda. La Paz, Bolivia Tel: (591-2) 34-32-45 Fax: (591-2) 35-92-68 McSilver, S.A. Bogota, Colombia Tel: (571) 270-4303 Fax: (571) 230-9205 Merisel Columbia Bogota, Columbia Tel: (571) 257-7800 Fax: (571) 610-0674 C.I.L.D.S.E. Quito, Ecuador Tel: (593) 2-54-3418 Fax: (593) 2-55-4780 Ace Computers & Electronics Georgetown, Guyana Tel: (592) 25-65-48 Fax: (592) 26-39-67 A.J.
Caribbean Caribbean Computer Systems, Ltd. Bridgetown, Barbados Tel: (809) 429-7050 Fax: (809) 427-6509 Da Costas Limited Bridgetown, Barbados Tel: (809) 427-5854 Fax: (809) 436-9870 Computer Business Systems Kingston, Jamaica Tel: (809) 925-8600 Fax: (809) 925-8115 WTG/ APTEC Systems Limited Kingston, Jamaica Tel: (809) 929-9250 Fax: (809) 929-8296 Boolchand Pessomal N.V.
