ELPMB25 User’s Guide
Contents Included Items List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Precautions on Where to Mount the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Profile Ceiling Mount Included Items List Check the following list and confirm that you have all of the supplied items. If there is anything missing or damaged, please contact your dealer. Y Ceiling plate Stacked on the c eiling plate and attached on the ceiling together. Y Ceiling plate Stacked under the ceiling plate and attached on the ceiling together. Y Ceiling plate Mounted on the ceiling plate . Used to adjust the projector's vertical/horizontal angle. They are stacked temporarily when packed.
Safety Instructions For your safety, read the attached documents carefully to assemble and install this product correctly. Be sure to follow the safety precautions. After you have read all instructions, keep this information for later reference. So that you can use the product safely and correctly, the following symbols are used to show dangerous operation or handling. The indications and their meaning are as follows. Make sure you understand them before reading the guide.
Warning v Do not strongly pull or pinch the projector's power cable during installation. Do not modify the power cable or use any damaged cable. Doing so may cause fire or electric shock. If the power cable is damaged (exposed conductor, breaking or the like), contact your dealer or Epson customer service call center. v Disconnect the power cable from the projector before cleaning. When cleaning it, do not use a moistened cloth or solvents such as alcohol, thinner or benzine.
Installation Installing the Ceiling Plate and Ceiling Plate on the Ceiling Determine the distance to the screen and locate the mounting position before mounting the ceiling plates. Refer to "Ceiling template" below for the size of the ceiling plate and the location of screw holes and their size. The projection distance to the screen varies according to the projector. Refer to "User's Guide" supplied with the projector or lens unit. Caution Be careful about where to mount the ceiling plates.
B Remove the tape which secures the ceiling plate and the ceiling plate . Then loosen the screws (not until they come off) that secure the plates with the ball point hex wrench. Tape Loosen these. Cutouts C Attach the ceiling plate and ceiling plate Set the cutouts to the screen. on the ceiling. Caution Take care not to catch the cables on or between the plates. Route the cables through the center hole of the plates.
Mounting the Ceiling Plate on the Ceiling Plate Warning Be sure to tighten the screws securely. After tightening the screws, try re-tightening them once again and make sure that all of them are securely tightened. Necessary items for the following procedure Y Ceiling plate Y M8x10 screws (mm) Y M4x10 screws (mm; w/ washer) Y Ball point hex wrench Procedure A Engage the screw holes onto the screws on the rear side of the ceiling plate . Set the ceiling plate with the adjustment dials to the screen.
C Insert the M4x10 screws into the screw holes on the screen side of the ceiling plate and tighten them with the ball point hex wrench. To the screen Secure these.
Mounting Projector Plate on the Projector Warning v Be sure to tighten the screws securely. After tightening the screws, try re-tightening them once again and make sure that all of them are securely tightened. v Applying threadlocker, lubricant, oil or other substance to the points at which the projector is fixed to this product may make the case crack and the projector may fall, and which may cause injury or an accident.
Mounting the Projector Plate to the Ceiling Plate Warning Keep holding the projector until the installation is complete. Necessary items for the following procedure Y M4x10 screws (mm; w/ washer) Y Ball point hex wrench Procedure A Insert the projector plate through the cutouts on the ceiling plate . White line B Slide the projector plate and engage the dowels on the projector plate into the cutouts on the ceiling plate .
Secure these. C Insert the M4x10 screws into the screw holes on the projector plate and tighten them with the ball point hex wrench. Angle adjustment should be done later, so there's no need to firmly tighten the screws. Warning Do not pull the cables forcibly. Do the same for the other side. When adjusting the angle of the projector, refer to "Adjusting the Position of the Projected Image" in the next section.
Adjusting the Position of the Projected Image If the projected image is not fit to the screen, adjust the projection position as follows. v Adjustment by the Lens Shift (for projectors with the lens shift function only) Adjust the projection position by the lens shift function of the projector. For the details on the lens shift, refer to "User's Guide" supplied with the projector. v Adjusting the Installation Angle The projection position can be adjusted by tilting or rotating the projector.
Shifting the Projected Image Up or Down Warning v Keep holding the projector until the installation is complete. v Do not loosen or remove the screws carelessly during vertical tilt adjustment. The projector may fall and cause an accident. v Do not apply extra force to the plate or projector during adjusting the plates. The projector or plates may fall and cause an accident. v After the adjustment, try re-tightening all the screws again and make sure that all of them are securely tightened.
Tighten these temporarily. C While supporting the projector, tighten the four screws temporarily with the ball point hex wrench. Do not tighten the screws too much at this point. Do the same for the other side. D Adjust the angle while lowering the projected image by turning the adjustment dial . If the projected image is lowered too much, go back to Step 1 and try again. Secure these. E After angle adjustment is complete, tighten the four screws firmly using the ball point hex wrench.
Shifting the Projected Image to the Right or Left Warning v Keep holding the projector until the installation is complete. v Do not loosen or remove the screws carelessly during horizontal rotation adjustment. The projector may fall and cause an accident. v Do not apply extra force to the plate or projector during adjusting the plates. The projector or plates may fall and cause an accident. v After the adjustment, try re-tightening all the screws again and make sure that all of them are securely tightened.
Adjusting the Projected Image's Horizontal Roll Warning v Keep holding the projector until the installation is complete. v Do not loosen or remove the screws carelessly during horizontal roll adjustment. The projector may fall and cause an accident. v Do not apply extra force to the plate or projector during adjusting the plates. The projector or plates may fall and cause an accident. v After the adjustment, try re-tightening all the screws again and make sure that all of them are securely tightened.
Installing the Ceiling Plate Cover Install the ceiling plate cover after adjusting the installation angles as necessary if you want to coordinate the colors of the projector and the ceiling. Necessary items for the following procedure Y Ceiling plate cover Y M4x10 screws (mm; w/o washer) Y Ball point hex wrench Procedure A Insert the ceiling plate cover to the rear side. Use the piece with a cutout to cover the rear side. Cutout Secure this. Do the same for the other side.
C D Secure this. Insert the other piece for the screen side and fit it to the ceiling plate cover for the rear side. Insert the M4x10 screws into the screw holes on the ceiling plate cover and tighten them with the ball point hex wrench. Do the same for the other side. Caution Removal, installation, and adjustment for repair or maintenance of the projector should be performed only by specialists with the required technical know-how and ability.
