User Manual
Table Of Contents
- Notations Used in This Guide
- Introduction to Your Projector
- Setting Up the Projector
- Using Basic Projector Features
- Turning On the Projector
- Turning Off the Projector
- Displaying a Test Pattern
- Projection Modes
- Adjusting the Image Position Using Lens Shift
- Adjusting the Projector's Tilt
- Image Shape
- Resizing the Image with the Zoom Feature
- Focusing the Image with the Lens Button
- Selecting an Image Source
- Image Aspect Ratio
- Color Mode
- Adjusting the Image Quality
- Adjusting the Image Color
- Adjusting Projector Features
- Monitoring and Controlling the Projector
- Adjusting the Menu Settings
- Using the Projector's Menus
- Using the Displayed Keyboard
- Image Quality Settings - Image Menu
- Input Signal Settings - Signal I/O Menu
- Projector Installation Settings - Installation Menu
- Projector Display Settings - Display Menu
- Projector Feature Settings - Operation Menu
- Projector Administration Settings - Management Menu
- Projector Network Settings - Network Menu
- Image Quality Memory Settings - Memory Menu
- Projector Initial Settings and Reset Options - Initial/All Settings Menu
- Copying Menu Settings Between Projectors (Batch Setup)
- Maintaining the Projector
- Solving Problems
- Appendix
- Optional Accessories and Replacement Parts
- Screen Size and Projection Distance
- Supported Monitor Display Resolutions
- Projector Specifications
- External Dimensions
- List of Safety Symbols and Instructions
- Laser Safety Information
- Glossary
- Notices
- FCC Compliance Statement
- Indication of the manufacturer and the importer in accordance with requirements of EU directive
- Indication of the manufacturer and the importer in accordance with requirements of United Kingdom directive
- Restriction of Use
- Operating System References
- Trademarks
- Copyright Notice
- Copyright Attribution
Viewing the Status Display
110
Version category: Displays the serial number and firmware version.
Information Description
Serial Number Displays the serial number.
Main Displays the main version information.
Video2 Displays the embedded software version.
Sub Displays the embedded software version.
HDMI Displays the embedded software version.
Pixel Shift Displays the embedded software version.
Network Wired category: Displays the wired network status.
Information Description
Projector Name Displays the name used to identify the projector when
connected to a network.
Connection Mode Displays the connection path for a wired network.
DHCP Displays the DHCP settings.
IP Display Displays the IP address display settings.
IP Address Displays the IP address.
MAC Address Displays the MAC address.
Input Signal category: Displays the signal status of the current input source.
Information Description
<1/3> -
Sync Detect(5V) Displays the detection results of signals.
Signal Status Displays the identification results of signals.
Resolution Displays the resolution.
Refresh Rate Displays the refresh rate and scanning method.
ColorSamp./Depth Displays the color sampling and bit depth.
Information Description
Color Space Displays the color space.
Dynamic Range Displays the dynamic range.
Video Range Displays the video range.
HDCP Status/Ver Displays the HDCP status and version.
Trans. Type Displays the transmission method.
Stable Time Displays the amount of operating time since the signal
changed.
<2/3> -
Signal Mode Displays the signal mode.
AVI VIC/Chk.Sum Displays the VIC code and checksum for AVI InfoFrame.
CLK-MHz/Frame-Hz Displays the actual measurement value of the pixel clock
frequency and refresh rate.
Total-H/V Displays the total number of pixels and lines including the
number of effective pixels and blanking.
Sync Polarity Displays the sync polarity of the horizontal and vertical
sync signals.
EDID Mode Displays the EDID mode.
Equalizer Level Displays the equalizer level.
<3/3> -
Audio Type Displays the audio signal type input to the source device
from the HDMI port.
Audio Freq/Depth Displays the audio signal frequency and bit depth input to
the source device from the HDMI port.
GCP A/V Mute Displays the A/V Mute status of GCP packets.
DDC Status Displays the source device and DDC communication
status.
gg Related Links
• "Getting the Latest Version of the Documents" p.7