User Manual December 2007 Revision 1.
Copyright 2007’ Dec. All Rights Reserved Manual Version 1.0 The information contained in this document is subject to change without notice. We make no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. We shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Safety IMPORTANT SAFETY INSTRUCTIONS 1. To disconnect the machine from the electrial power supply, turn off the power switch and remove the power cord plug from the wall socket. The wall socket must be easily accessible and in close proximity to the machine. 2. Read these instructions carefully. Save these instructions for future reference. 3. Follow all warnings and instructions marked on the product. 4. Do not use this product near water. 5. Do not place this product on an unstable cart,stand,or table.
LEGISLATION AND WEEE SYMBOL 2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment, collection, recycling and disposal of electric and electronic devices and their components. The crossed dustbin symbol on the device means that it should not be disposed of with other household wastes at the end of its working life. Instead, the device should be taken to the waste collection centers for activation of the treatment, collection, recycling and disposal procedure.
Table of Contents 1. CHECKLIST....................................................................................... 7 2. FEATURES ........................................................................................ 8 3. SPECIFICATION................................................................................ 8 4. COLOR CLIP INSTALLATION ........................................................... 9 5. INTERFACE.....................................................................................
10. COMMAND DETAILS ...................................................................... 23 10.1. POS7300 SERIES COMMAND LIST ................................................................. 23 10.2. CD5220 STANDARD MODE COMMAND LIST..................................................... 25 10.3. UTC STANDARD MODE COMMAND LIST .......................................................... 28 10.4. UTC ENHANCED MODE COMMAND LIST .......................................................... 28 10.5.
1.
2. Features 1. Data can be displayed on 20 columns x 2 lines. 2. Blue–green color and large characters are easy to see. 3. The DIP switches set the command mode emulation, baud rate and international character set. 4. Command emulation modes include: POS7300, EPSON ESC/POS, ADM787/ ADM788, DSP800, AEDEX/ EMAX, UTC, and CD5220. 5. Display area can be controlled by a window function. 6. RS-232C and USB interface, and RS232C baud rate from 4800 to 38400 bps. 7.
4. Color Clip Installation a. Place the color clip on the bezel b.
5. Interface 5.1. Specification Data transmission Serial / USB Synchronization Asynchronous Handshaking DTR / DSR MARK = -3 to –15 V (logic “1”) Signal level SPACE = +3 to +15 V (logic “0”) 5.2. Baud rates 4800,9600,19200,38400 bps Parity None, even Bit length 8 bits Stop bits 1 bit Display Base The picture below shows the configuration of the stand alone VFD Pole Display base.
5.3. Connector POWER USB RJ45 PWR: Power input connector from adapter Connector type: DC jack (5.5mm/2.
RJ45: Connect to display panel Connector type: Phone-jack 10P/8C 10 1 Pin assignment Pin 1 Pin 3 Pin 5 Pin 7 Pin 9 +5V_VBus +12V RS232_DTR RS232_DSR# RS232_RX# Pin 2 Pin 4 Pin 6 Pin 8 Pin 10 +12V GND USB_PRS232_TX# USB_P+ COM: RS232C link to PC/HOST connector (9-pin) Connector type: D-sub 9 pin female Pin assignment Pin 1 Pin 3 Pin 5 Pin 7 Pin 9 +12V_COM RS232_TX# GND RS232_RTS# N/C Pin 2 Pin 4 Pin 6 Pin 8 RS232_RX# RS232_DTR RS232_DSR# RS232_DSR# 12
6. Driver Installation 6.1. Driver List Folder/File File Description :\OCD_100.htm OCD 100 Driver List :\Common\USB2COM\PL-2303HX USB-VFD PL2303 Driver 6.2. USB Driver Installation a. Click th “PL-2303 Driver Installer” on the “Win98-ME_2X_XP_2003” window 13 b.
c. Click the “Finish” button on the IntallShiedld window The driver will be installed on the first free COM port in the system. In general this will be COM7, but the actual number may be different, depending on your system configuration. You can check the actual COM port used by the customer display in the Windows Device Manager.
7. Dip Switch and Software Setting Please open the dip switch cover to access the DIP switches.
7.1. Command Type Selection SW1 ON OFF ON OFF ON OFF ON OFF 7.2. SW2 ON ON OFF OFF ON ON OFF OFF SW9 ON ON OFF OFF Demo Mode Support No Yes No Yes No No No Yes Baud Rate (bps) 4800 9600 19200 38400 Default ＊ Parity Check Selection SW10 ON OFF 7.4. Command Type POS7300 EPSON ESC/POS ADM 787/ ADM 788 DSP800 AEDEX/ EMAX UTC/P UTC/S CD5220 Baud Rate Selection SW8 ON OFF ON OFF 7.3.
7.5. International Character Set ID SW SW SW SW SW Character Set 4 5 6 7 11 (20h – 7Fh) 0 ON ON ON ON OFF U.S.A.
8. Software Status Setting Commands When the system is POWER ON, it will read the DIP switch to set the Command Type, Baud Rate, Parity and International Character. The user can reset the Software Status Setting Commands as following: 8.1. Baud Rate Setting Command STX 05 B n ETX ASCII Format Dec. Format Hex. Format Description n 31h 30h 37h 36h 8.2.
8.3. International Character Set Setting Command STX 05 S n ETX ASCII Format Dec. Format Hex. Format Description n /Change the international character set/ STX 05 S n ETX [02] [05] [83] n [03] [02h][05h][53h] n [03h] 30h≦n≦4Fh Change the display international character font. Character Set (20h – 7Fh) Code Table (80H-FFH) CP-437 (USA, Standard Europe) 30h U.S.A. 31h 32h 33h 34h 35h 36h 37h 38h 39h 3Ah 3Bh 3Ch 3Dh 3Eh 3Fh 40h 41h 42h 43h 44h 45h 46h 47h 48h 49h ~ 4Fh FRANCE GERMANY U.K.
8.4. Command Type Setting Command STX 05 C n ETX ASCII Format Dec. Format Hex. Format Description n 30h 31h 32h 33h 8.5. Command Type DSP800 ESC/POS POS7300 ADM 787 n 34h 35h 36h 37h Command Type AEDEX UTC/P UTC/S CD5220 Run Demo message STX 05 D 08 ETX ASCII Format Dec. Format Hex. Format Description 8.6. /Change the command type setting/ STX 05 C n ETX [02] [05] [67] n [03] [02h][05h][43h] n [03h] 30h≦ n≦37h This command will change the command type and initialize the display.
9.
Command List Table – 2 POS7300CD5220 Upper line message continuous scroll Bottom line message scroll continuously Message vertical down scroll continuously Message vertical upper scroll continuously Carriage return Line feed Back space Horizontal tab Command type select Upper line message scroll once pass Change attention code Two line display Clear upper line and move cursor to upper left-end position Clear bottom line and move cursor to bottom left-end position Set period to upper line, last n position S
10. Command Details 10.1.
POS7300 Standard Mode Command List-2 Command BS HT LF HOM CLR CR CAN ESC = n Code (hex) 08 09 0A 0B 0C 0D 18 1B 3D n Function Description Back space Horizontal tab Line feed Move cursor to home position Clear display screen Carriage return Clear cursor line, and clear string mode Select peripheral device, display or printer ¾ n = 1~3 n = '1': enable printer only n = '2': enable display only n = '3': enable both of printer and display 24
10.2.
CD5220 Standard Mode Command List-2 Command Code (hex) ESC W s x1 x2 y 1B 57 s x1 x2 y CLR CAN ESC * n US X n ESC _ n 0C 18 1B 2A n 1F 58 n 1B 5F n ESC f n 1B 66 n ESC c n 1B 63 n ESC = n 1B 3D n Function Description Set or cancel the window range at horizontal scroll mode ¾ 1 ≦ x1 ≦ x2 ≦ 14h, for columns location. ¾ y = 1~2, for lines location.
4. The parameter of the code table control by command “ESC c n”.
10.3. UTC Standard Mode Command List Command BS HT LF CR DLE n 08 09 0A 0D 10 n Code (hex) DC1 DC2 DC3 DC4 US ESC d 11 12 13 14 1F 1B 64 Function Description Back space Horizontal tab Line feed Carriage return Display position ¾ n = 0 ~ 27h, for location. Over write display mode Vertical scroll mode Cursor on Cursor off Clear display Change to UTC enhanced mode 10.4.
10.5. AEDEX/EMAX Mode Command List Command Code (hex) ! # 4 [DATA] 21 23 34 [DATA] 0D CR ! # 5 h h : m m 21 23 35 h h ':' m m 0D CR ! # 8 n m CR 21 23 38 n m 0D ! # 9 [DATA] CR ! # 6 [DATA] CR 21 23 39 [DATA] 0D 21 23 36 [DATA] 0D Function Description Upper line message scroll ¾ Maximal [DATA] length is 40 Display time ¾ h, m = '0' ~ '9' Change attention code ¾ n, m = 1 ~ 20 Two line display ¾ Maximal [DATA] length is 40 Upper line message scroll once pass ¾ Maximal [DATA] length is 40 10.6.
10.7.
10.8. EPSON ESC/POS Command List EPSON ESC/POS Command List-1 Command Code (hex) Function Description US r n 1F 72 n Select/cancel reverse character. ¾ n = 00,01 US MD1 1F 01 Specify overwrite mode. US MD2 1F 02 Specify vertical scroll mode. US MD3 1F 03 Specify horizontal scroll mode. CAN 18 Clear cursor line ESC # n 1B 23 n Command type select ¾ n = 30h ~ 38h US # n x 1F 23 n x Turn annunciator on/off. ¾ n = 0 for annunciator off n = 1 for annunciator on ¾ x = 1 ~ 14h, for columns location.
EPSON ESC/POS Command List-2 Command Code (hex) Function Description US ^ n m 1F 5E n m Execute and quit macro. It’s an interval of n between the two words. It’s an interval of m between the two strings.
11. Character Set 11.1. Character Code 20H – 7FH 11.1.
11.2. Character Code 80H – FFH 11.2.1 80h 90h A0h B0h C0h D0h E0h F0h 11.2.2 80h 90h A0h B0h C0h D0h E0h 11.2.
11.2.4 80h 90h Katakana for Japan 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh α £ A0h β γ ⊿ є η θ § IE IR ∫ x Ā 。 「 」 、 ‧ λ -1 μ ² π ³ ρ x σ τ Ф Ω ∑ ½ 1/ √ ± ■ B0h C0h D0h E0h F0h 11.2.
11.2.7 80h 90h A0h B0h C0h D0h E0h F0h 11.2.
11.2.10 CP-862 (Hebrew) 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 80h 90h A0h B0h C0h D0h E0h F0h א נ á ░ └ ╨ α ≡ ב ס í ▒ ┴ ╤ ß ± ג ע ó ▓ ┬ ╥ Γ ≥ ד ף ú │ ├ ╙ π ≤ ה פ ñ ┤ ─ ╘ Σ ⌠ ו ץ Ñ ╡ ┼ ╒ σ ⌡ ז צ ª ╢ ╞ ╓ µ ÷ ח ק º ╖ ╟ ╫ τ ≈ ט ר ¿ ╕ ╚ ╪ Φ ° י ש ⌐ ╣ ╔ ┘ Θ · ך ת ¬ ║ ╩ ┌ Ω · כ ¢ ½ ╗ ╦ █ δ √ ל £ ¼ ╝ ╠ ▄ ∞ ⁿ ם ¥ ¡ ╜ ═ ▌ φ ² מ ₧ « ╛ ╬ ▐ ε ■ ן ƒ » ┐ ╧ ▀ ∩ 11.2.
11.2.13 CP-866 (Cyrillic) 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 80h 90h A0h B0h C0h D0h E0h F0h А Р а ░ └ ╨ р Ё Б С б ▒ ┴ ╤ с ё В Т в ▓ ┬ ╥ т Є Г У г │ ├ ╙ у є Д Ф д ┤ ─ ╘ ф Ї Е Х е ╡ ┼ ╒ х ї Ж Ц ж ╢ ╞ ╓ ц Ў З Ч з ╖ ╟ ╫ ч ў И Ш и ╕ ╚ ╪ ш ° Й Щ й ╣ ╔ ┘ щ · К Ъ к ║ ╩ ┌ ъ · Л Ы л ╗ ╦ █ ы √ М Ь м ╝ ╠ ▄ ь № Н Э н ╜ ═ ▌ э ¤ О Ю о ╛ ╬ ▐ ю ■ П Я п ┐ ╧ ▀ я 11.2.
11.2.16 Windows-1253 (Greek) 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 80h 90h A0h B0h C0h D0h E0h F0h € ‚ ƒ ‘ ’ “ ΅ Ά £ ± ² ³ ΐ Α Β Γ Π Ρ Σ ΰ α β γ π ρ ς σ „ … † ‡ ‰ ” • – — ™ ¤ ¥ ¦ § ¨ © ´ µ ¶ · Έ Ή Δ Ε Ζ Η Θ Ι Τ Υ Φ Χ Ψ Ω δ ε ζ η θ ι τ υ φ χ ψ ω ‹ › « ¬ – ® Ί » Ό ½ Ύ Κ Λ Μ Ν Ξ Ϊ Ϋ ά έ ή κ Λ μ ν ξ ϊ ϋ ό ύ ώ ¯ Ώ Ο ί ο 11.2.
12. Display Module Dimensions 200mm 0.38o 176mm 39mm 70mm 158.6mm 5.25mm 0.85mm 0.25mm 1.05mm 0.25mm 9.0mm 9.5mm 1.5mm 22.5mm 1.5mm 1.5mm 6.
