SERVICE MANUAL Serial Impact Dot Matrix Printer EPSON FX-890/2190 ® SEDM02003
Notice All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted in any form or by any means electronic, mechanical, photocopying, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION. All effort have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly appreciate being informed of them.
PRECAUTIONS Precautionary notations throughout the text are categorized relative to 1)Personal injury and 2) damage to equipment. DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing procedures preceded by DANGER Headings. WARNING Signals a precaution which, if ignored, could result in damage to equipment.
About This Manual This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page. Manual Configuration Symbols Used in this Manual This manual consists of six chapters and Appendix. CHAPTER 1.
Revision Status Revision Date of Issue A June 20, 2003 B August 21, 2003 Description Formal first release Revision up: Chapter-3: Error Correction ("3.2.12 Fatal Error" on page 63) Chapter-4: Error Correction ("4.2.3 C524MAIN Board" on page 74) Appendix: The part list and the exploded diagram for the FX-2190 are added. ("7.3 Exploded Diagrams" on page 114, "7.
EPSON FX-890/2190 Revision B Table of Contents Chapter 1 PRODUCT DESCRIPTIONS Chapter 2 Operating Principles 1.1 Features ............................................................................................................... 9 1.2 Interface ............................................................................................................. 1.2.1 Parallel interface (Forward channel) ........................................................ 1.2.2 Parallel interface (Reverse channel) .....
EPSON FX-890/2190 Revision B 3.2.11 Electrical Noise ....................................................................................... 62 3.2.12 Fatal Error ............................................................................................... 63 3.3 Troubleshooting for Individual Units ............................................................. 64 3.3.1 Main Component Checking Point ............................................................ 64 Chapter 4 Disassembly and Assembly 4.
1 CHAPTER PRODUCT DESCRIPTIONS
EPSON FX-890/2190 Revision B 1.1 Features PRINTING SPEED EPSON FX-890/2190 is a small-foot 18-pin serial impact dot matrix printer. Table 1-2.
EPSON FX-890/2190 Revision B FEEDING METHOD PAPER SPECIFICATIONS Friction feed : Front, Rear Push tractor feed : Front, Rear Push & Pull tractor feed : Front, Rear Pull tractor feed : Front, Rear, Bottom Table 1-3. Cut Sheet (Single sheet, Not multi part) FX-890 Front Entry FX-890 FEED SPEED Normal mode Copy mode 4.23 mm (1/6 inch feed) Continuous feed 4.23 mm (1/6 inch feed) Continuous feed FEEDER Front push tractor Rear push tractor CSF Bin 1 / Bin 2 (Option) 62 msec 0.
EPSON FX-890/2190 Revision B Table 1-4. Cut Sheet (Single sheet, Not multi part) FX-2190 Front Entry FX-2190 Manual Manual Rear Entry High-Capacity CSF Min. Max. Table 1-5. Cut Sheet (Multi part) FX-890 Front Entry Single-Bin CSF FX-890 Manual Rear Entry Manual / High-Capacity CSF / Single-Bin CSF Minimum Maximum Min. Max. Min. Max. Min. Max. Minimum Maximum Width (inch) (mm) (3.9) 100 (16.5) 420 (3.9) 100 (16.5) 420 (3.9) 100 (16.5) 420 (7.2) 182 (16.
EPSON FX-890/2190 Revision B Table 1-6. Cut Sheet (Multi part) FX-2190 Front Entry FX-2190 Manual Table 1-7. Card Rear Entry Manual / High-Capacity CSF / Single-Bin CSF Minimum Maximum Front Entry FX-890 & FX-2190 Manual Min. Max. Minimum Maximum Width (inch) (mm) (3.9) 100 (16.5) 420 ----- ----- Width (inch) (3.9) (mm) 100 Length (inch) (mm) (3.9) 100 (16.5) 420 ----- ----- Length (inch) Copies 1 original + 5 copies ----- Total thickness (inch) (mm) (0.0047) 0.12 (0.018) 0.
EPSON FX-890/2190 Revision B Table 1-8. Envelope Front Entry FX-890 & FX-2190 Manual Min. Max. Envelope Width (inch) (mm) (No.6) Length (inch) Manual Min. Max. (6.5) 165 ----- ----- (3.6) 92 ----- ----- (9.5) 241 ----- (4.1) 105 ----- ----- (mm) Total Thickness Weight (inch) (mm) (g/m2) ----- (0.0063) 0.16 (0.0205) 0.52 ----- ----- The difference of thickness at the printable area is within 0.25 mm (0.0098 inch) ----- ----- (lb) CSF capacity Single-Bin CSF Min. Max.
EPSON FX-890/2190 Revision B Table 1-11. Continuous paper (Single sheet and Multi Part) FX-890 Table 1-12. Continuous paper (Single sheet and Multi Part) FX-1190 Bottom/Front/Rear Entry Minimum Maximum FX-890 Bottom/Front/Rear Entry Minimum Maximum FX-2190 Width (inch) (mm) (4) 101.6 (10) 254 Width (inch) (mm) (4) 101.6 (16) 406.4 Length (one page) (inch) (mm) (4) 101.6 (22) 558.8 Length (one page) (inch) (mm) (4) 101.6 (22) 558.
EPSON FX-890/2190 Revision B Table 1-14. Labels (FX-2190) Table 1-13. Labels (FX-890) Bottom/Front Entry Minimum Maximum See Figure 1-1 below. FX-890 Label size Rear Entry Minimum Maximum Label size ----- Base sheet width (inch) (mm) (4) 101.6 (10) 254 ----- ----- Base sheet length (one page) (inch) (mm) (4) 101.6 (22) 558.8 ----- Base sheet Thickness (inch) (mm) (0.0028) 0.07 (0.0035) 0.09 Total thickness (inch) (mm) (0.0063) 0.16 (0.0075) 0.
EPSON FX-890/2190 Revision B CHARACTER TABLES Table 1-15. Roll Paper FX-890& FX-2190 Bottom/Front Entry Minimum Maximum Rear Entry Minimum Maximum Standard version : 13 tables Width (inch) (mm) ----- (8.5) 216 NLSP version : 42 tables Length (inch) (mm) ----- ----- International character sets : 13 countries Diameter (inch) (mm) ----- Thickness (inch) (mm) ----- (0.0028) 0.07 (0.0035) 0.
EPSON FX-890/2190 Revision B ELECTRICAL SPECIFICATION Table 1-18. UPS Version Table 1-16. 120V Version Rated voltage AC 120 V Input voltage range AC 103.5 to 132 V Rated frequency range 50 to 60 Hz Input frequency range 49.5 to 60.5 Hz Rated current 1.1 A (Max. 2.5 A) Power consumption Approx.53 W (ISO/IEC 10561 Letter pattern) Approx. 3.5 W in sleep mode * 0 W in power off mode Energy Star compliant Insulation resistance 10 MΩ min.
EPSON FX-890/2190 Revision B ACOUSTIC NOISE Level: 55 dB(A) (ISO 7779 pattern) Color Black Ribbon dimensions 13 mm (W) x 17 M (L) Endless Ribbon life Approximately 7.
EPSON FX-890/2190 Revision B CE MARKING EXPENDABLES & OPTIONS Table 1-19. Expendables & Option 230 V version & UPS version Expendables Low Voltage Directive 73/23/EEC: EN60950 EMC Directive 89/336/EEC: EN55022 class B EN61000-3-2 EN61000-3-3 EN55024 INTERFACE Bi-directional parallel interface (IEEE-1284 nibble mode supported) USB (ver1.1) I/F Type-B I/F level 2 (Option) CONTROL CODE ESC/P IBM PPDS emulation Ribbon cartridge (Black) Code No.
EPSON FX-890/2190 Revision B PRINTABLE AREA Table 1-20. Printable Area for Cut Sheet Single Sheet / Multi Part Cut sheets PW (Width) PL (Length) LM (Left Margin) RM (Right Margin) TM (Top Margin) BM (Bottom Margin) FX-890 FX-2190 Refer to “PAPER SPECIFICATIONS” Table 1-3 on page 10 for single sheet or Table 1-5 on page 11 for multi part Refer to “PAPER SPECIFICATIONS” Table 1-4 on page 11 for single sheet or Table 1-6 on page 12 for multi part 3 mm or more (PW<=209.2 mm) 26.
EPSON FX-890/2190 Revision B Continuous paper Envelope PW LM RM TM Printable Area PL Printable Area Figure 1-3. Printable Area for Envelope BM Table 1-21. Printable Area for Envelope Envelope Printable Area PW (Width) PL (Length) Figure 1-4. Printable Area for Continuous Paper Refer to “PAPER SPECIFICATIONS” Table 1-8 on page 13 LM (Left Margin) RM (Right Margin) TM (Top Margin) BM (Bottom Margin) Table 1-22. Printable Area for Continuous Paper 3 mm or more Continuous Paper 4.
EPSON FX-890/2190 Revision B Label Roll paper PW LM RM TM 1.2mm or more PW TM LM RM Printable area PL Printable area BM 6.35mm or more Figure 1-6. Printable Area for Roll Paper Table 1-24. Printable Area for Roll Paper Roll Paper Figure 1-5. Printable Area for Label PW (Width) PL (Length) LM (Left Margin) Table 1-23.
EPSON FX-890/2190 Revision B 1.2 Interface Table 1-25. Connector pin assignment (Forward channel) (continued) This printer provides bi-directional 8-bit parallel interface, USB interface and Type-B optional interface slot as standard. 1.2.1 Parallel interface (Forward channel) Specifications Pin No. Signal Name Return GND Pin IN/ Out* Function description 12 PE 28 Out This signal’s high level means that the printer is in a state of paper-out error.
EPSON FX-890/2190 Revision B Data transmission timing BUSY signal is active (high level) under any of the following conditions: In the process of receiving data DATA Input buffer full data byte n+1 data byte n t hold -INT signal active (low level) -STROBE t setup During hardware initialization t next t stb -ERROR or PE signal active (low level or high level, respectively) BUSY In the self test mode t ready t busy In the adjustment mode -ACKNLG t reply In the default-se
EPSON FX-890/2190 Revision B FX-2190 1.2.2 Parallel interface (Reverse channel) When IEEE1284.
EPSON FX-890/2190 Revision B 1.2.3 USB Interface Table 1-27. Connector pin assignment (Reverse channel) 1 HostClk Return GND Pin 19 2 DATA1 3 Pin No. Signal Name IN/ Out* Specifications Function description Standard: Based on “Universal Serial Bus Specifications Revision 1.1” “Universal Serial Bus Device Class Definition for Printing Devices Version 1.
EPSON FX-890/2190 Revision B 1.2.4 Optional Interface 1.2.5 Type-B Interface communication specification Type-B optional interface cards are available. Reply for Optional command (*: Reply for Type-B I/F Level 2 device: not described in user's manual) Table 1-29. FX-890 Reply message Main-Type Product-Name ESC/P MT9p, PW80c110cpi, PRG(Wxxxxx)rev, AP500ma IBM PPDS MT9p, PW80c110cpi, PRG(Wxxxxx)rev, AP500ma FX-890 FX-890 Table 1-31.
EPSON FX-890/2190 Revision B Main command 1.2.6 Interface selection Table 1-32. Main command Option command number 01h Command name Sending Timing • • • • • Init signal on the std.
EPSON FX-890/2190 Revision B 1.2.7 IEEE1284.4 protocol The packet protocol described by IEEE1284.4 is supported on the parallel I/F. Two function modes of IEEE1284.4 protocol, “Off” and “Auto”, are available and one of them is selected according to the value of Default setting. (See Section 1.3.5. Default Setting). NOTE:Packet protocol option “Off” &“Auto” in Default setting mode are effective in not only parallel I/F but also USB I/F.
EPSON FX-890/2190 Revision B 1.3 Operation 1.3.2 Switches This section describes the operations on this printer. 1.3.2.1 Operation in Normal Mode In the normal mode, pressing panel switches executes the following functions. 1.3.1 Control panel Table 1-33. Normal Mode The control panel of this printer is equipped with 6 switches and 10 LEDs, which are located as shown below. Switch Font Pitch • Selects pitch. Reset (Font & Pitch) • Resets the printer.
EPSON FX-890/2190 Revision B 1.3.2.2 Operations at Power-on 1.3.3 Indicators ( LEDs ) Holding down the specified switch (switches) while turning on the power to the printer enables the special functions as listed below. This printer has the following indicators to indicate its current condition, as shown in the table below: Table 1-34. At Power-On Switches 1.3.3.1 Indications in Normal Mode Function Load/Eject Table 1-36.
EPSON FX-890/2190 Revision B *2. Paper Out ( Red ) *5. Pitch ( Green ) The “Paper Out” LED is on when the printer is in the “paper out” status, and it Three LEDs display the status of Pitch selection. blinks when the printer has developed a paper eject error, and it is off when the printer is not in such status. See *6 for LED indication when a locked switch is pressed. *3. Tear Off / Bin (Green) Two LEDs display the status of CSF bin selection when cut sheet is used.
EPSON FX-890/2190 Revision B 1.3.4 Buzzer 1.3.5 Default Setting This printer has the buzzer to indicate its current condition with the following indications. You can change some parameters that the printer refers to at printer initialization. 1.3.5.1 Setting Method The symbols used in the table above represent the following: Refer to the following flowchart for default setting.
EPSON FX-890/2190 Revision B 1.3.5.2 Setting Items Table 1-38. Setting Values Available in Default Setting Mode (continued) Setting values available for default setting and factory settings are as shown in the table below: Table 1-38. Setting Values Available in Default Setting Mode Item Page length for front tractor Page length for rear tractor 3inch, 3.5inch, 4inch, 5.5inch, 6inch, 7inch, 8inch, 8.
EPSON FX-890/2190 Revision B 1.3.6 EEPROM Clear Function Table 1-39. Cleared Items and Values on EEPROM (Standard Model) (continued) You can return some parameters into the factory settings to perform panel operation easily. Pressing Load/Eject & LF/FF & Pause switches at the same time while turning on the printer returns the default settings into the factory settings: Item Buzzer Auto CR Tear-off adjustment value Table 1-39.
EPSON FX-890/2190 Revision B 1.3.7 Bi-D Adjustment Refer to the following flowchart for the Bi-D adjustment. start Turning the printer on while pressing Pause switch. The guide to adjust Bi-d. alignment in this mode is printed and first alignment pattern is printed. [ Step A ] Select most closely alignment number by pressing Item ↓ (Font) and Item ↑ (Pitch) switches. Font LEDs show the pattern number which is selected at that time.
EPSON FX-890/2190 Revision B 1.4 Dimensions and Weight Physical specifications Dimensions: Weight: 589 mm (W) x 350mm (D) x 167.5mm (H) * Approximately TBD kg * This measure excludes “the protrusions.” FX-890 Dimensions: Weight: Appearance: FX-2190 414 mm (W) x 350 mm (D) x 167.5 mm (H) * Approximately 7.6 kg See the figures below. * This measure excludes “the protrusions.” Figure 1-17. Physical Specifications for FX-2190 Figure 1-16.
EPSON FX-890/2190 Revision B Physical specifications including High capacity cut sheet feeder (Bin1) FX-2190 Dimensions: Weight: FX-890 Dimensions: Weight: Appearance: 414 mm (W) x 434 mm (D) x 378 mm (H) * Approximately 8.9 kg See the figures below. 589mm (W) x 434mm (D) x 378mm (H) * Approximately TBD kg * This measure excludes “the protrusions.” * This measure excludes “the protrusions.” Figure 1-19.
EPSON FX-890/2190 Revision B Physical specifications including Single bin cut sheet feeder (Bin2) FX-2190 Dimensions: Weight: FX-890 Dimensions: Weight: Appearance: 414 mm (W) x 445 mm (D) x 386 mm (H) * Approximately 8.2 kg See the figures below. 589mm (W) x 445mm (D) x 386mm (H) * Approximately TBD kg * This measure excludes “the protrusions.” * This measure excludes “the protrusions.” Figure 1-21.
EPSON FX-890/2190 Revision B Physical specifications including High capacity cut sheet feeder (Bin) & Single bin cut sheet feeder (Bin2) Dimensions: Weight: FX-890 Dimensions: Weight: Appearance: FX-2190 414 mm (W) x 564 mm (D) x 408 mm (H) * Approximately 9.5 kg See the figures below. 589mm (W) x 564mm (D) x 408mm (H) * Approximately TBD kg * This measure excludes “the protrusions.” Figure 1-23.
EPSON FX-890/2190 Revision B FX-880T+ (=ML320T) mode is different from “current FX-890” mode in the 1.4.1 FX-880T+ Mode C A U T IO N following features: This function may be used only on the models intended for EAI market. On any model intended for any other market, do not execute the command to enter this mode.
EPSON FX-890/2190 Revision B 1.4.1.3 Default setting items 1.4.1.5 Action of the printer Table 1-40. Setting Values Available for Default Setting Mode Item Setting / Value ESC/P, IBM PPDS, OKI ML320T *IBM PPDS is the same as IBM 238x plus. Software Interface FX-880T+ mode does not have Device ID. Only Parallel I/F is possible use. (Can not use USB I/F and Optional Type-B I/F) Tear Off Auto tear Off Wait Time 0.5 second, 1 second, 2 seconds, others Bottom margin 4.
2 CHAPTER OPERATING PRINCIPLES
EPSON FX-890/2190 Revision B 2.1 Overview C524 PSB/PSE/PSH Board This printer is divided into several main components for easy removal and repair.
EPSON FX-890/2190 Revision B 2.1.1 Printer Mechanism 2.1.1.2 Paper Feed Mechanism This printer mechanism consists of Printhead, Paper feed mechanism, Carriage movement mechanism, Tractor feed mechanism, Platen gap adjustment mechanism, Ribbon feed mechanism, PF motor, CR motor, detectors, and so on. The paper feed mechanism picks up paper and transports it to the printhead, then ejects the paper step by step or continuously driven by the PF motor.
EPSON FX-890/2190 Revision B 2.1.1.6 Ribbon Feed Mechanism 2.1.1.7 Sensors The CR motor drives the ribbon feed mechanism via the timing belt. The ribbon feed mechanism has the sun and planetary gear system. No matter the carriage unit is driven left and right, the ink ribbon is driven in one direction. Table below lists the sensors of this printer. Tractor PG Detector Table 2-1.
EPSON FX-890/2190 Revision B 2.1.2 Circuit Operation Table 2-2. Major Elements on MAIN Board (continued) Elements Location 2.1.2.1 C524 MAIN Board Use: Device: Type: The C524 MAIN board is the control circuit board of this printer. This board consists of several IC chips and drivers, as described in the table below: Table 2-2. Major Elements on MAIN Board Elements Location DRAM IC5 Function Package: 240 SQFP (0.5 mm between pins) Manufacturing process: 0.
EPSON FX-890/2190 Revision B Table 2-2. Major Elements on MAIN Board (continued) Elements Location Table 2-2. Major Elements on MAIN Board (continued) Function Elements Level 2 Current consumption 0.5 A max. SSI is supported. Transmission rates supported are 600/1200/2400/4800/ 9600/19200 [bps]. Data reception rate (between TYPE B and Main Circuit Board) is 2 MB/s at peak.
EPSON FX-890/2190 Revision B Table 2-2.
EPSON FX-890/2190 Revision B 2.1.2.2 C524 PSB/PSE/PSH Power Supply Circuit This printer can be powered by one of the following three power supply boards: the C524PSB (120 V) board, the C524PSE (230 V) board, or the C524PSH (Universal) board. The function of the boards is the same, except for a difference in the primary circuitry. The power supply outputs the DC current necessary to drive the printer control circuit and drive the mechanism. INPUT SPECIFICATIONS Table 2-4.
EPSON FX-890/2190 Revision B Table 2-4. Input Specifications Power Supply Unit Name Special output holding time (The period from the time when output 1 has dropped below 26 V to the time when output 2 drops below the output voltage lower limit) PROTECTIVE FUNCTIONS C524 PSB (100-120V Spec) C524 PSE (220-240V Spec) 120 ms or more C524 PSH (100-240V Spec) (Input: 85 V, 60 Hz) (Input: 187 V, 50 Hz) (Input: 85 V, 60 Hz) Table 2-6.
3 CHAPTER TROUBLESHOOTING
EPSON FX-890/2190 Revision B 3.1 Overview 3.1.2 Procedure for Troubleshooting Perform troubleshooting work according to the flowchart shown at right. The printer may exhibit different symptoms for the same problem, which makes troubleshooting more difficult. This section, however, provides simple and effective ways to facilitate troubleshooting. C A U T IO N In addition, the User's Manual for EPSON EPSON FX-890/2190 describes detailed steps to be taken for recovery from typical errors.
EPSON FX-890/2190 Revision B 3.1.3 Preliminary Checks Make sure that gears of the printer mechanism do not rub each other excessively. Before starting troubleshooting, be sure to verify that the following conditions are all met: Make certain that the rollers inside the printer are free from soiling and free from Confirm that all gears are engaged properly. The power supply voltage must be within the specification limits. (Measure the scratches.
EPSON FX-890/2190 Revision B 3.2 Troubleshooting Based on Symptoms 3.2.1 Printer fails to operate when power is turned on You can identify the defective component from the symptom displayed. Table 3-2 below lists the symptoms for various failures so that you can easily identify the problem. Based on the symptom as mentioned below, identify the problem and take a remedy by following the appropriate troubleshooting procedure given in Table 3-3 to Table 3-13. Table 3-3.
EPSON FX-890/2190 Revision B 3.2.2 No LED on Control Panel lights up even with power turned on Table 3-4. No LED on Control Panel lights up Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Fuse • Power Switch • Control Panel (p.72) • Harness of Control Panel • C524MAIN Board (p.74) • C524PSB/PSE/PSH Board (p.
EPSON FX-890/2190 Revision B 3.2.4 Abnormal paper feeding Table 3-6. Abnormal paper feeding Step Table 3-6. Abnormal paper feeding Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Front PE (Paper End) Detector (p.87) • Harness of Front PE Detector • Rear PE Detector (p.87) • Harness of Rear PE Detector • Release Detector (p.86) • Harness of Release Detector • Rear Paper Guide Assembly (p.90) • PF Motor (p.83) • PF Gear Train (p.
EPSON FX-890/2190 Revision B 3.2.5 Printing is faulty during self-test, but carriage operation is normal Table 3-7. Printing faulty during self-test, but carriage operation normal Step Table 3-7. Printing faulty during self-test, but carriage operation normal Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Fuse • Printhead (p.77) • CR Motor (p.81) • PF Motor (p.83) • C524PSB/PSE/PSH Board (p.76) • C524MAIN Board (p.
EPSON FX-890/2190 Revision B 3.2.6 Abnormal operation of Control Panel 3.2.7 Abnormal on-line operation (normal self-printing, though) Table 3-8. Abnormal operation of Control Panel Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Control Panel (p.72) • Harness of Control Panel • C524MAIN Board (p.
EPSON FX-890/2190 Revision B 3.2.8 Abnormal operation of ribbon Table 3-10. Abnormal operation of ribbon Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Ribbon Cartridge • Timing Belt • CR Motor (p.81) • Ribbon Drive (RD) Assembly (p.92) • C524MAIN Board (p.74) 1 Ribbon Cartridge Defective Ribbon Cartridge 2 Defective Carriage Check the operation of the Carriage and Timing Belt. Go to Step 2 Replace the Ribbon Cartridge.
EPSON FX-890/2190 Revision B 3.2.9 Abnormal operation of Carriage Unit Table 3-11. Abnormal operation of Carriage Unit (continued) Table 3-11. Abnormal operation of Carriage Unit Step Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Timing Belt • CR Motor (p.81) • HP (Home Position) Detector (p.78) • Harness of HP Detector • Ribbon Drive (RD) Assembly (p.92) • C524MAIN Board (p.
EPSON FX-890/2190 Revision B 3.2.10 Faulty print 3.2.11 Electrical Noise Table 3-12. Faulty print Step Action and Question Table 3-13. Troubleshooting for Electrical Noise Yes No Step Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • Ribbon Mask • Printhead (p.77) • Printhead FFC • C524MAIN Board (p.74) 1 Ribbon Mask Remove the Ribbon Mask from the Printhead, and make sure that the Ribbon Mask is free from deformation or damage.
EPSON FX-890/2190 Revision B 3.2.12 Fatal Error Table 3-14. Troubleshooting for Fatal Error (continued) Action and Question Table 3-14. Troubleshooting for Fatal Error Action and Question Yes No Parts below can be the source of this error (Chapter 4 Disassembly and Assembly) • C524MAIN Board (p.74) • C524PSB/PSE/PSH Board (p.76) • Printhead (p.77) • CR Motor (p.81) • PF Motor (p.83) • HP (Home Position) Detector (p.
EPSON FX-890/2190 Revision B 3.3 Troubleshooting for Individual Units Table 3-16. F Common Line 3.3.1 Main Component Checking Point Corresponding Wires R Common Line Corresponding Wires The following components can be checked with a simple measurement tool, such as a multi-meter, easily. C1 1, 7, 13 C5 2, 5, 11 C2 9 C6 3, 15 Motors C3 10, 18 C7 16, 17 C4 6, 12 C8 4, 8, 14 Table 3-15. Motor Coil Resistance Test Points Motor Test Pin Number Test Method* Meter Reading 16.
4 CHAPTER DISASSEMBLY AND ASSEMBLY
EPSON FX-890/2190 Revision B 4.1 Overview 4.1.2 Tools and Instruments This section describes procedures for disassembling and assembling EPSON FX-890/ 2190. Unless otherwise specified, disassembled units or components can be reassembled by reversing the disassembly procedure. Therefore, no assembly procedures are included in this section. Precautions for any disassembly or assembly procedure are described under the heading “CHECK POINT”.
EPSON FX-890/2190 Revision B 4.1.3 Service Check After Repair Table 4-2. Repair Status Check List (continued) After completing repair of the product, use the check list shown below to check the status of the repaired product and overall repair work performed before returning the product to the users. This list can be used as a record of all service works performed with the product.
EPSON FX-890/2190 Revision B 4.1.3.1 Abbreviations for Small Parts Table 4-3. List of Screws Used The table below lists the abbreviations used in this manual for small parts, such as screws and washers. Table 4-3. List of Screws Used No. Name and specification 11 PRINTER MECHANISM MOUNTING SCREW No.
EPSON FX-890/2190 Revision B 4.2 Main Components Disassembly This section provides the disassembly procedures. The basic order for disassembly is shown in the flowchart below. The exploded diagrams are also provided in the “Exploded Diagrams” (page 114). Refer to them to see how components are engaged with each other if necessary. START Main Components Disassembly Pre-disassembly Procedures (p.70) Printhead (p.77) HP (Home Position) Detector (p.78) Platen (p.79) Upper Housing (p.
EPSON FX-890/2190 Revision B 4.2.1 Pre-disassembly Procedures Paper Eject Cover Remove the Paper Guide Assembly, top cover, front cover, paper eject cover, knob and tractor unit. Paper Guide Assembly. (See Figure 4-2) Top cover.(See Figure 4-2) Knob. (See Figure 4-2) Paper eject cover. (See Figure 4-3) Front cover. (See Figure 4-4) Tractor unit. (See Figure 4-5) Figure 4-3. Paper Eject Cover Removal Paper Guide Assembly Top cover Front Cover Figure 4-4.
EPSON FX-890/2190 Revision B C A U T IO N Remove the paper eject cover and the tractor unit by pushing and releasing the hooks at both sides. When remounting them, be sure to snap these hooks on the projecting parts. Figure 4-5.
EPSON FX-890/2190 Revision B 4.2.2 Upper Housing CBS Screws (3x8) x2 Tightening Torque: 1.08 ±0.1 N.m 1. Perform Pre-Disassembly. (p.70) 2. Remove 3 CBS (M3x8) screws securing the upper housing to the lower case. (See Figure 4-6) 3. Set the release lever to the friction feed side. 4. Lifting the front side of the upper housing a little, disengage the hook found at the left of the panel assembly. 5.
EPSON FX-890/2190 6. Revision B Open the upper housing from the front side, and remove it. C A U T IO N When assembling the upper housing, put the catching holes in the upper housing on the hooks at the rear side of the lower case at first, then close the housing. (See Figure 4-7) Mount the Panel assembly onto the upper housing before installing the upper housing assembly. Sheet, Release, Cap can be assembled after the upper housing assembly is installed.
EPSON FX-890/2190 Revision B 4.2.3 C524MAIN Board C A U T IO N CBS Screws (3x6) x5 Tightening Torque: 0.58-0.78 N.m The C524MAIN board has the mechanical drive power supply voltage (+42V, Vp) management circuit and an electrical characteristic of the components composed of this circuit is measured with the custom instruments and regulated at the assembly process. Never attempt to replace any components of this circuit on the board, and doing so resulted in damaging the unit.
EPSON FX-890/2190 5. Revision B Remove the 2 CBS (M3x12) screws securing the COVER,CONNECTOR,UPPER or the optional Type-B I/F Board to the I/F GROUNDING PLATE. (See Figure 4-10) 6. Remove the 6 CBP (M3x12) screws securing the C524MAIN Board to the lower case. 7. Lift the rear side of the I/F GROUNDING PLATE slightly and remove the I/F GROUNDING PLATE together with the C524MAIN board. 8. Remove the 3 CP (M3x4) screws securing the I/F GROUNDING PLATE to the C524MAIN board.
EPSON FX-890/2190 Revision B 4.2.4 C524PSB/PSE/PSH Board 1. Perform Pre-Disassembly. (p.70) 2. Remove the Upper Housing. (p.72) 3. Remove the shield cover. (See Figure 4-8) 4. Disconnect the harness from the connector CN14 on the C524MAIN board. (See Figure 4-11) 5. Disconnect the power cable from the connector CN1 on the C524PSB/PSE/PSH Board. 6. Remove the 2 CBP (M3x12) screws securing the C524PSB/PSE/PSH Board to the Lower Case, and remove the C524PSB/PSE/PSH Board.
EPSON FX-890/2190 Revision B 4.3 Printer Mechanism Disassembly Ribbon Mask 4.3.1 Printhead 1. Remove the top cover.(See Figure 4-2) 2. Remove the 2 CBS C (P2) (M3x8) screws securing the Printhead to the Carriage Assembly.(See Figure 4-12) 3. Disconnect the head FFC from the Printhead and remove it. W A R N IN G CBS C(P2) Screws (3x8) x2 Tightening Torque : 0.7±0.1 N.m Be careful with the Printhead when you handle it, as it may be very hot right after printing.
EPSON FX-890/2190 Revision B 4.3.2 HP (Home Position) Detector Hook 1. Remove the top cover. (See Figure 4-2) 2. Release the hook attaching the HP detector to the Printer Mechanism, and remove it. (See Figure 4-13) 3. Disconnect the harness of the detector from the detector connector. Harness HP Detector Hook Figure 4-13.
EPSON FX-890/2190 Revision B 4.3.3 Platen CBS Screws (3x8) x2 Tightening Torque: 0.9±0.1N.m 1. Perform Pre-Disassembly. (p.70) 2. Remove the 2 CBS (M3x8) screws securing the COVER,PLATEN. (See Figure 4-14) 3. Rotating the teeth of the Bushing, 8, Right and Bushing 8 Left forward, disengage them from the Left/Right Side Frame. 4. Move the carriage to the right end, lift the left side of the platen slightly, move the carriage to the center and remove the platen to the left.
EPSON FX-890/2190 Revision B 4.3.4 Printer Mechanism 1. Perform Pre-Disassembly. (p.70) 2. Remove the Upper Housing. (p.72) 3. Remove the shield cover.(See Figure 4-8) 4. Disconnect all the connectors connected to the C524MAIN board. (See Figure 4-9) 5. Remove the 2 CBP (M3x8) screws securing the MOUNT HOUSING to the lower housing, and remove the MOUNT HOUSING. (See Figure 4-16) 6. Remove the 4 CBB (W13, M3x14) screws, and remove the Printer Mechanism by lifting it up.
EPSON FX-890/2190 Revision B 4.3.5 CR Motor 1. Remove the Printer Mechanism. (p.80) 2. Release the tension spring. (See Figure 4-17) 3. Disengage the TIMING BELT,CR from the CR Motor pinion and hang it on the Hanger. CR Motor TIMING BELT,CR Tension Spring Hanger Figure 4-17.
EPSON FX-890/2190 Revision B 4. Remove the 2 SHAFT,MOUNT,CR (M3x12) screws securing the CR Motor assembly to the FRAME,SUB,RIGHT, and remove the CR Motor. (See Figure 4-18) 5. Remove the 2 CB (M3x6) screws securing the CR Motor to the MOUNTING PLATE,MOTOR,CR, and remove the CR Motor. A D J U S T M E N T R E Q U IR E D CR Motor After installing the CR Motor, make the following adjustment: SHAFT,MOUNT,CR Screws (3x10) x2 Tightening Torque: 0.9±0.1N.m • Bi-d Adjustment (p.
EPSON FX-890/2190 Revision B 4.3.6 PF Motor 1. Remove the Printer Mechanism. (p.80) 2. Release the motor harness from the Printer Mechanism. (See Figure 4-19) 3. Locate the release lever (Lever, Release) in the forefront position (Tractor Position). 4. Remove the 2 (CBS (M3x10), CB (M3x8)) screws securing the PF Motor to the FRAME,SUB,RIGHT, and remove the PF Motor. CBS Screw (3x10) Tightening Torque: 0.9±0.1N.
EPSON FX-890/2190 Revision B 4.3.7 PF Gear Train 1. Remove the Printer Mechanism. (p.80) 2. Remove the PF Motor. (p.83) 3. Locate the release lever (Lever, Release) in the forefront position (Tractor Position). 4. Remove the head FFC from the FRAME,SUB,RIGHT of the Printer Mechanism. (See Figure 4-20) 5. Remove the 2 (CBS (M3x8), CB (M3x8)) screws securing the FRAME,SUB,RIGHT, and remove the FRAME,SUB,RIGHT. FRAME,SUB,RIGHT Head FFC CBS Screws (3x8) Tightening Torque: 0.9±0.1N.
EPSON FX-890/2190 Revision B Lubrication is necessary at two points. (For details, refer to “Lubrication” (p.100) in Chapter 6.) Pay attention to the gear engagement position of the LEVER,RELEASE. For assembly, follow the following procedure: 1. Make certain that the SHAFT,RELEASE is in the Tractor position. 2. Install the INTERMITTENT GEAR in a position as shown below. 3. Install the LEVER,RELEASE and LEVER, RELEASE, TRANSMISSION in the Tractor position.
EPSON FX-890/2190 Revision B 4.3.8 PG (Platen Gap) Detector 4.3.9 Release Detector 1. Remove the Printer Mechanism. (p.80) 1. Remove the Printer Mechanism. (p.80) 2. Release the 2 clips attaching the PG detector to the LEFT FRAME in the Printer Mechanism, and remove the detector. (See Figure 4-22) 2. Release the 2 clips attaching the Release detector to the FRAME,SUB,RIGHT in the Printer Mechanism, and remove the detector. (See Figure 4-23) 3. Disconnect the harness from the detector. 3.
EPSON FX-890/2190 Revision B 4.3.10 Front PE (Paper End) Detector 4.3.11 Rear PE Detector 1. Remove the Printer Mechanism. (p.80) 1. Remove the Printer Mechanism. (p.80) 2. Release the 2 clips attaching the front PE detector to the Rear Paper Guide Assembly, and remove the detector. (See Figure 4-24) 2. Hold the Printer Mechanism horizontally. 3. Release the 2 clips securing Rear PE detector to Rear Paper Guide Assembly. 3. Disconnect the harness from the detector. 4.
EPSON FX-890/2190 Revision B 4.3.12 Carriage Assembly 1. Remove the Printer Mechanism. (p.80) 2. Remove the Head FFC. (See page 77) 3. Remove the Platen. (p.79) 4. Remove the CR Motor. (p.81) 5. Remove the hexagon nut (M4) and the washer securing the LEVER,G,ADJUST to the SHAFT,CR,GUIDE, and remove the lever. (See Figure 4-26) 6. Remove the BUSHING,PARALLEL,ADJUST to turn the SHAFT,CR,GUIDE.
EPSON FX-890/2190 Revision B 7. Move the Carriage Assembly to the right end, and remove it from the rack of the FRAME,FRONT with the SHAFT,CR,GUIDE. (See Figure 4-27) 8. Release the TIMING BELT from the 2 clips at the bottom of the Carriage Assembly. A D J U S T M E N T R E Q U IR E D TIMING BELT After installing the Carriage Assembly, make the following adjustments: • Bi-d Adjustment (p.101) • Platen Gap Adjustment (p.95) Clips Lubrication is necessary at three points.
EPSON FX-890/2190 Revision B 4.3.13 Rear Paper Guide Assembly 1. Remove the Printer Mechanism. (p.80) 2. Remove the Platen. (p.79) 3. Remove the hexagon nut and the washer securing the LEVER,G,ADJUST to the SHAFT,CR,GUIDE, and remove the lever. (See Figure 4-26) 4. Remove the BUSHING,PARALLEL,ADJUST to turn the SHAFT,CR,GUIDE. (See Figure 4-26) 5. Remove the harness for PG Detector. (See page 86) 6. Remove the harness for HP Detector. (See page 78) 7.
EPSON FX-890/2190 Revision B 10. Release the cables from the HOLDER,CABLE on the RIGHT FRAME, and remove the HOLDER,CABLE from the RIGHT FRAME. FRAME,REAR 11. Remove the CBS (M3x8) screw securing the FRAME,REAR to the RIGHT FRAME, and remove the Rear Paper Guide Assembly. (See Figure 4-30) 12. Push and slide the clip on the left side of the Rear Paper Guide Assembly laterally, and separate the Rear Paper Guide Assembly and the FRAME, REAR from each other. Clip Lubrication is necessary.
EPSON FX-890/2190 Revision B 4.3.14 Ribbon Drive (RD) Assembly CBS C(P2) Screw (3x8) Tightening Torque: 0.9±0.1N.m 1. Remove the Printer Mechanism. (p.80) 2. Remove the Platen. (p.79) 3. Remove the hexagon nut and the washer securing the LEVER,G,ADJUST to the SHAFT,CR,GUIDE, and remove the lever. (See Figure 4-26) 4. Remove the BUSHING,PARALLEL,ADJUST to turn the SHAFT,CR,GUIDE. (See Figure 4-26) 5. Remove the harness for PG Detector. (See page 86) 6.
5 CHAPTER ADJUSTMENT
EPSON FX-890/2190 Revision B 5.1 Adjustment Overview 5.1.2 Adjustment Tools Table 5-2 below shows the tools required for each adjustment. 5.1.1 Required Adjustment This section describes the adjustments required after specified parts are removed or replaced. Table 5-1 below shows the parts removed/replaced and corresponding adjustments required. Adjustment Platen Gap Bi-d Adjustment Table 5-1. Required Adjustment Removal or Replacement Requiring Adjustment Table 5-2.
EPSON FX-890/2190 Revision B 5.2 Adjusting and Resetting the Printer 5.2.1 Platen Gap Adjustment When the SHAFT,CR,GUIDE or BUSHING,PARALLEL,ADJUST is rotated or reinstalled, or printing is too faint or stained, the Platen Gap adjustment must be performed by the following procedure: 1. Remove the Upper Housing. (p.72) 2. Remove the Printhead. (p.77) 3. Using tweezers, remove the Ribbon Mask from the ribbon mask holder of the Carriage Assembly.
EPSON FX-890/2190 Revision B 11. Put an adjustment gauge between the Printhead and the PLATEN vertically, and judge and adjust the platen gap by referring to Table 5-3 below. For adjustment, turn the SHAFT,CR,GUIDE toward the PLATEN (widen) or toward the front (lessen). (See Figure 5-2, Figure 5-3) Criterion 0.37 mm Falls by its own weight 0.40 mm Does not fall by its own weight Copy Mode Platen Gap (PG) [mm] Table 5-3. Criteria for Platen Gap Adjustment Gauge Normal Mode 12.
EPSON FX-890/2190 Revision B 5.3 Adjustment Program Sequential Adjustment Mode This mode is specifically designed to assist repair engineer to preform all necessary adjustment/setting item in proper order. A wizard like menu help you to select necessary adjustment in accordance with the type of repair you have made.
6 CHAPTER MAINTENANCE
EPSON FX-890/2190 Revision B 6.1 Overview 6.1.1 Preventive Maintenance Preventive maintenance is important to keep the printer in the best condition and to prevent potential troubles from occurring. If necessary, use denatured alcohol to clean the exterior cases. Use a vacuum cleaner to remove dust and paper debris accumulated in the printer. W A R N IN G C A U T IO N Before disassembling, assembling or adjusting the printer, disconnect the power supply cable from the AC power socket.
EPSON FX-890/2190 Revision B 6.2 Lubrication Table 6-2. Lubrication Points Influence that oil and grease give is considerably large especially in low temperature. Therefore, EPSON has tested and analyzed various types of oil and grease extensively, and found the oil and grease listed below most applicable to the printer. Assy to be Lubricated (Reference Page) PF Gear Train (p.84) Table 6-1. Lubrication Type Oil Name O-14 Quantity 40 g Available EPSON Part No.
EPSON FX-890/2190 Revision B SPUR GEAR, 34.5 G-26 G-26 Figure 6-1. Lubrication Point (PF Gear Train) G-26 G-26 SPUR GEAR, 21 G-26 Ratchet,RD Figure 6-2. Lubricating Point (RD Assy 1) Maintenance Figure 6-3.
EPSON FX-890/2190 G-26 Revision B Combination Gear, 8.19 Shaft Release G-26 G-26 Spur Gear, 25.5 Combination Gear, 7.5,15 G-26 Figure 6-6. Lubricating Points (Shaft Release) Figure 6-4. Lubricating Points (RD Assy 3) O-14 Direction of Leaf Spring G-26 Holder, PF, Shaft Holder, PF, Shaft Plain Washer Figure 6-7. Lubricating Points (Carriage Assembly) Figure 6-5.
EPSON FX-890/2190 Revision B G-26 Roller, PF, Drive PG Adjusting holes (7 holes) Figure 6-8.
7 CHAPTER APPENDIX
EPSON FX-890/2190 Revision B 7.1 Connector Summary The primary components of the printer are connected as shown below; Table 7-1. Connector Summary Board C524MAIN Board C524 PSB/PSE/PSH Board Control Panel Appendix Connector No.
EPSON FX-890/2190 Revision B Parallel I/F (CN1) Refer to “Parallel interface (Forward channel)” (page 23). Type-B I/F (CN2) Refer to “Type-B Interface communication specification” (page 27). HP Detector(CN8) Table 7-5. Connector Pin Assignment - CN8 Pin No. I/O Signal Name 1 I HP 2 - GND USB I/F (CN3) Refer to “USB Interface” (page 26). PG Detector (CN5) Table 7-2. Connector Pin Assignment - CN5 Function I/O Signal Name Pin No.
EPSON FX-890/2190 Revision B Printhead (CN15, CN16) F side (CN16: lower connector) R side (CN15: upper connector) Table 7-10. Connector Pin Assignment - CN16 Pin No. I/O Signal Name 1 – – #3 Head Data 2 O HEAD1 #1 Head Data Not used 3 O HEAD9 #9 Head Data #15 Head Data 4 O HEAD13 #13 Head Data #2, 5, 11 Common 5 O HEAD7 #7 Head Data #2 Head Data 6 – C1 #3, 15 Common 7 – – Table 7-9. Connector Pin Assignment - CN15 Not used Pin No.
EPSON FX-890/2190 Revision B 7.2 Electric Circuit Diagrams The following pages show circuit diagrams below.
EPSON FX-890/2190 Revision B 7.
103 181 106 181 181 109 127 181 127 133 184 117 184 104 180 120 105 C 141 102 A J K C B 185 D G 185 E H F L M 138 D 150 151 111 110 A 182 116 125 183 108 B I 180 132 180 180 121 180 112 182 112 101 180 112 122 181 115 107 100 F OR F X-890 101 NO.1 137 R ev.
350 300 I C J K A 450 C B D G 372 A 400 NO.2 R ev.
557 662 546 548 533 551 535 545 552 563 535 550 561 562 560 564 556 585 584 615 614 583 524 544 610 573 521 650 181 581 579 576 600 537 569 660 661 589 620 531 K 528 578 503 572 617 181 623 618 J I 534 602 575 588 536 526 181 570 568 181 581 534 532 621 622 619 653 577 530 525 M 619 502 504 182 549 527 551 610 603 L 532 574 652 522 543 547 552 G 184 523 533 542 582 597 613 651 601 607 595 590 593 655 660 E 587 181 511 661 580 501 500
02 04 04 xx 02 03 05 02 06 07 05 01 F OR F X-890 NO.4 R ev.
118 The parts to which no reference number is assigned will not be available as after-sale service parts. 106 105 120 113 103 102 104 119 A 126 125 108 B 126 110 109 125 150 151 125 133 115 125 A 126 F 126 101 116 126 126 121 135 127 123 F D H E B J K L F 100 111 112 107 FOR FX-2190 112 NO.1 Rev.
450 A B 372 A 373 F F D H 330 G E I B J 200 K L F 400 FOR FX-2190 NO.2 Rev.
548 551 546 542 610 533 573 610 603 552 545 544 575 650 568 585 584 550 543 547 549 588 I 524 521 F 583 527 565 H 536 552 551 589 570 652 L 530 532 534 572 534 534 571 502 561 560 564 615 569 600 579 123 577 600 576 593 618 557 562 600 123 586 620 531 621 622 528 597 601 595 616 501 607 582 556 563 504 522 523 526 J 603 K 525 535 540 505 503 613 590 610 605 511 609 E 500 541 586 540 505 The parts to which no reference number is assigned will not be avail
EPSON FX-890/2190 Revision B 7.4 Parts List Table 7-11. Parts List - FX-890 DESCRIPTION REF# 127 C.B.S. SCREW(B300204311) Table 7-11. Parts List - FX-890 132 "GROUNDING PLATE,I/F" DESCRIPTION 133 "GROUNDING PLATE,I/F,UPPER" FX-890 REF# NON FIG "SOFTWARE CD-ROM,EAI" 137 "GROUNDING PLATE,BOTTOM" NON FIG USER'S GUIDE 138 "HOLDER,CABLE" 100 "HOUSING ASSY.,LOWER" 141 "SHEET,PANEL" 101 FOOT 150 "DETECTOR ASSY.,CASE OPEN" 102 "HOUSING ASSY.
EPSON FX-890/2190 Revision B Table 7-11. Parts List - FX-890 Table 7-11. Parts List - FX-890 DESCRIPTION REF# DESCRIPTION REF# CN20 CONNECTOR 524 CONNECTOR SWITCH;B CN3 CONNECTOR 525 "PAPER GUIDE ASSY.,REAR" CN5 CONNECTOR 526 "SHAFT,RELEASE" CN6 CONNECTOR 527 "HARNESS,PE,FRONT" CN7 CONNECTOR(X600440310) 528 "HARNESS,PE,REAR" CN8 CONNECTOR(X600440120) 529 "HARNESS,RE" CN9 CONNECTOR(X600440120) 530 "DETECTOR,PE,FRONT,S" D1 DIODE 531 "DETECTOR ASSY.
EPSON FX-890/2190 Revision B Table 7-11. Parts List - FX-890 Table 7-11. Parts List - FX-890 DESCRIPTION REF# DESCRIPTION REF# 552 RETAINING RING(B150300911) 587 "MOUNTING PLATE,MOTOR,CR" 556 "COVER, PAPER EJECT" 588 "HOLDER,RIBBON MASK" 557 "FRAME,PAPER EJECT;EPAG" 589 OIL PAD(F334005140) 560 "LEAF SPRING,PAPER EJECT,DOUBLE" 590 "LEVER,RELEASE;EDGB" 561 "SPUR GEAR,15" 591 "CAM,CLUTCH,TRACTOR" 562 "SPUR GEAR,11.
EPSON FX-890/2190 Revision B Table 7-11. Parts List - FX-890 Table 7-11. Parts List - FX-890 DESCRIPTION REF# DESCRIPTION REF# 618 "SPUR GEAR,36" 619 RETAINING RING(B160101412) NON FIG OIL O-14 620 "LEVER,DETECTOR,PE,REAR" NON FIG GREASE G-26 (40GR) 621 "LEVER,PE,SUPPORT" 622 "TORSION SPRING,0.26" 623 "PLAIN WASHER,3X0.5X8,F/ZB" 650 HEAD KIT ASP 651 "EXTENSION SPRING,16.45" 652 "HOLDER,PULLEY DRIVEN" 653 "CABLE,HEAD" 655 "SHAFT,CR,GUIDE" 660 "C.B.
EPSON FX-890/2190 Revision B Table 7-12. Parts List - FX-2190 FX-2190 Ref. No. Table 7-12. Parts List - FX-2190 Ref. No. Description NON FIG "SOFTWARE CD-ROM,EAI" NON FIG USER’S GUIDE 100 "HOUSING ASSY.,LOWER" 101 FOOT 102 "HOUSING ASSY.,UPPER" 103 "COVER ASSY.,PRINTER,REAR" 104 "COVER ASSY.,PRINTER" 105 WIHG;EPAG 106 SHEET GUIDE ASSY 107 "COVER ASSY.
EPSON FX-890/2190 Revision B Table 7-12. Parts List - FX-2190 Ref. No. Table 7-12. Parts List - FX-2190 Description Ref. No. Description CN16 CONNECTOR 501 "FRAME ASSY.,RIGHT" CN2 CONNECTOR 502 "FRAME ASSY.,LEFT" CN20 CONNECTOR 503 "MOTOR ASSY.,CR" CN3 CONNECTOR 504 RD ASSY.
EPSON FX-890/2190 Revision B Table 7-12. Parts List - FX-2190 Ref. No. Table 7-12. Parts List - FX-2190 Description Ref. No. Description 543 "TRACTOR,RIGHT;EDGB" 576 "PAPER GUIDE ASSY.
EPSON FX-890/2190 Revision B Table 7-12. Parts List - FX-2190 Ref. No. Description 605 C.B.SCREW(B010303311) 607 "PLANE WASHER,8.2X0.5X12,L/NA" 609 C.B.SCREW(B010303511) 610 C.B.SCREW(B010303411) 613 "SHAFT,MOUNT,CR" 615 "HOLDER,CABLE,HEAD" 616 "SHEET,RELEASE,CAP" 618 "SPUR GEAR,36" 620 "LEVER,DETECTOR,PE,REAR" 621 "LEVER,PE,SUPPORT" 622 "TORSION SPRING,0.26" 650 HEAD KIT ASP 651 "EXTENSION SPRING,16.
