User Manual
Table Of Contents
- For Safety
- Restriction of Use
- Note about interference
- Open Source Software License
- About this Manual
- Contents
- Product Overview
- Setup of the Tablet
- Setup of the Printer
- Flow of Setup
- Placing the Printer
- Changing the Paper Width
- Connecting Peripheral Devices
- Connecting the Wireless LAN Unit
- Connecting the Customer Display
- Connecting the Optional External Buzzer
- Connecting the Cash Drawer
- Connecting to the Power Source
- Connecting the Printer to the Host Devices
- Attaching the Power Switch Cover
- Enabling the Roll Paper Near-End Detection
- Using Dedicated Optional Products
- Advanced Usage
- Software Settings
- Functions
- Receive buffer capacity
- BUSY condition
- Auto line feed
- USB power-saving function
- Release condition of receive buffer BUSY
- Select paper out detector enabled for paper out signal output
- Error signal settings
- Pre-feed before next print
- Roll paper near-end detection
- Network tethering
- Paper width
- Print density
- Print speed
- Thai characters print mode
- Character code table defaults
- International character defaults
- Interface selection
- Column emulation mode
- Command execution during offline
- Amount of top margin by backfeed
- Interface switch waiting time
- Main connection interface
- Autocutting after closing cover
- Paper reduction
- Font A auto replacement
- Font B auto replacement
- Font C auto replacement
- Multi-tone print density
- Optional buzzer
- Batch rotate print (Upside Down)
- Communication condition of USB interface
- Communication condition of Bluetooth interface
- Bluetooth communication interval during power saving mode
- Functions
- Network Settings
- Setting/Check Modes
- Printing a Status Sheet
- Resetting the Interface Settings
- TM-Intelligent Function
- Network Tethering (iOS device only)
- Software Settings
- Application Development Information
- Handling
- Appendix
- Product Specifications
- Specifications of Interface and Connector
- Bluetooth Low Energy Technology Advertising
- Character Code Tables
- Compatibility with USB Type-A
91
Chapter 5 Advanced Usage
Setup using EpsonNet Config
Execute EpsonNet Config, select the target printer from the displayed device list, then check and change the
settings.
If the printer is still set to factory defaults, the printer's MAC address is listed up, even if the computer does not
have the same network address.
1
Connect the printer to the same network as the computer where you installed
EpsonNet Config.
2
Start up EpsonNet Config.
The tool automatically detects printers connected to the network and displays a list.
It may take up to a minute for the printer to be displayed in the list.
If it is not displayed, check that [Filter] is set to "(All)" or "Network-connected devices", then click
[Refresh]. Or, select [Tools], then [Option], and check the settings of [Search Parameters].
3
Select the target printer, then click [Configuration].
If you cannot determine the target printer from the product name or the IP address, use the MAC
address. You can check the printer's MAC address on the status sheet.
4
Change the printer's settings based on the network setting information you received
from the network administrator.
Select an item from the menu and change the setting.
5
Once you set the necessary items, click [Transmit].
The changed contents are sent to the printer and the printer settings are changed.
• The initial setting uses an IP address for the printer provided by a DHCP server. Since you cannot
complete setup if there are conflicting IP addresses on the network, make sure that there are no
other devices on the network that conflict with the IP address provided by the DHCP server. If a
DHCP server is not available, a fixed IP address (192.168.192.168) is set approximately one minute
after turning on the printer. Also, if the Ethernet cable is not connected, connect the Ethernet cable
and then run this process.
• When DHCP is enabled, the provided IP address is printed automatically. However, if the Ethernet
cable is not connected, and the Wireless LAN unit is not installed, printing is not performed.
For details about EpsonNet Config, see the manual (operation guide) installed together with the
tool or the online help.