User Manual
Table Of Contents
- For Safety
- Restriction of Use
- Note about interference
- Open Source Software License
- About this Manual
- Contents
- Product Overview
- Setup of the Tablet
- Setup of the Printer
- Flow of Setup
- Placing the Printer
- Changing the Paper Width
- Connecting Peripheral Devices
- Connecting the Wireless LAN Unit
- Connecting the Customer Display
- Connecting the Optional External Buzzer
- Connecting the Cash Drawer
- Connecting to the Power Source
- Connecting the Printer to the Host Devices
- Attaching the Power Switch Cover
- Enabling the Roll Paper Near-End Detection
- Using Dedicated Optional Products
- Advanced Usage
- Software Settings
- Functions
- Receive buffer capacity
- BUSY condition
- Auto line feed
- USB power-saving function
- Release condition of receive buffer BUSY
- Select paper out detector enabled for paper out signal output
- Error signal settings
- Pre-feed before next print
- Roll paper near-end detection
- Network tethering
- Paper width
- Print density
- Print speed
- Thai characters print mode
- Character code table defaults
- International character defaults
- Interface selection
- Column emulation mode
- Command execution during offline
- Amount of top margin by backfeed
- Interface switch waiting time
- Main connection interface
- Autocutting after closing cover
- Paper reduction
- Font A auto replacement
- Font B auto replacement
- Font C auto replacement
- Multi-tone print density
- Optional buzzer
- Batch rotate print (Upside Down)
- Communication condition of USB interface
- Communication condition of Bluetooth interface
- Bluetooth communication interval during power saving mode
- Functions
- Network Settings
- Setting/Check Modes
- Printing a Status Sheet
- Resetting the Interface Settings
- TM-Intelligent Function
- Network Tethering (iOS device only)
- Software Settings
- Application Development Information
- Handling
- Appendix
- Product Specifications
- Specifications of Interface and Connector
- Bluetooth Low Energy Technology Advertising
- Character Code Tables
- Compatibility with USB Type-A
19
Chapter 1 Product Overview
About the USB connector (USB-A - Device Charging, The white USB connector)
• Make sure you use the genuine cable for the tablet, smartphone, or USB device you are using.
• Charging may not be performed depending on the device's charging specifications.
• To set an optimum current value for charging the connected device, it may take several
seconds before charging starts. Charging may stop temporarily immediately after the device is
connected.
• If a device connected to the USB connector (USB-A Device Charging) has a rated power that
exceeds the rated current of the USB connector, charging the device is stopped. See "Product
Specifications" on page 131.
• T
he device may not be fully charged depending on its settings or usage conditions. For
example, when the device is used with the screen brightness set to its maximum, and/or with
the sleep function disabled.
• Seiko Epson Corporation assumes no responsibility for economic damages or problems arising
from failure of charging the connected device due to a failure or malfunction of the product.
• It may be hard to disconnect some types of USB cable. Do not forcibly pull the cable, or the
USB connector and USB cable may be damaged. Contact qualified service personnel if you
encounter the trouble.
• To communicate with a tablet computer via Bluetooth while charging the tablet through the
USB connector (USB-A - Device Charging) on the printer, set the "Interface selection" setting to
"Bluetooth only". For more details, see "Software Settings" on page 81.
How
ever, if you do so, the maximum supply current is limited to 0.5 A, which may not be
enough for charging some types of tablet. Please use the tablet after testing and evaluating it
adequately.
• When connecting an Android device to the USB connector (USB-A - Device Charging) for data
communication, make sure that the device satisfies the following requirements.
Requirements: The version of Android OS is 10 or later with kernel version 4.9.15 or later
However, Epson does not guarantee normal operation of all Android devices even if they
satisfy the requirements. Run some tests before actually using the device.
• If the printer is connected to a wired network, an iOS tablet connected to the printer via the
USB connector can access the network through the Lightning to USB cable. For more details,
see "Network Tethering (iOS device only)" on page 109