User Manual
Table Of Contents
- For Safety
- Restriction of Use
- Note about interference
- Open Source Software License
- About this Manual
- Contents
- Product Overview
- Setup of the Tablet
- Setup of the Printer
- Flow of Setup
- Placing the Printer
- Changing the Paper Width
- Connecting Peripheral Devices
- Connecting the Wireless LAN Unit
- Connecting the Customer Display
- Connecting the Optional External Buzzer
- Connecting the Cash Drawer
- Connecting to the Power Source
- Connecting the Printer to the Host Devices
- Attaching the Power Switch Cover
- Enabling the Roll Paper Near-End Detection
- Using Dedicated Optional Products
- Advanced Usage
- Software Settings
- Functions
- Receive buffer capacity
- BUSY condition
- Auto line feed
- USB power-saving function
- Release condition of receive buffer BUSY
- Select paper out detector enabled for paper out signal output
- Error signal settings
- Pre-feed before next print
- Roll paper near-end detection
- Network tethering
- Paper width
- Print density
- Print speed
- Thai characters print mode
- Character code table defaults
- International character defaults
- Interface selection
- Column emulation mode
- Command execution during offline
- Amount of top margin by backfeed
- Interface switch waiting time
- Main connection interface
- Autocutting after closing cover
- Paper reduction
- Font A auto replacement
- Font B auto replacement
- Font C auto replacement
- Multi-tone print density
- Optional buzzer
- Batch rotate print (Upside Down)
- Communication condition of USB interface
- Communication condition of Bluetooth interface
- Bluetooth communication interval during power saving mode
- Functions
- Network Settings
- Setting/Check Modes
- Printing a Status Sheet
- Resetting the Interface Settings
- TM-Intelligent Function
- Network Tethering (iOS device only)
- Software Settings
- Application Development Information
- Handling
- Appendix
- Product Specifications
- Specifications of Interface and Connector
- Bluetooth Low Energy Technology Advertising
- Character Code Tables
- Compatibility with USB Type-A
152
Appendix
Bluetooth Low Energy Technology Advertising Packet Format
In the TM-m30II-SL, the iBeacon format is used by default for the Bluetooth low energy technology Advertising
Packet.
The UUID for the TM-m30II-SL is "fac1ba2f-61a2-4d83-9a8c-60087c232569".
The user can edit the following specifications in the iBeacon format: UUID, Major number, Minor number, and
Measured Power.
Table 1 iBeacon Packet Format
Changing the Bluetooth Low Energy Technology Advertising Packet
The TM-m30II-SL can acquire a configuration script from the printer.
You can also change settings by transmitting the configuration script to the printer.
The configuration script only supports UTF-8 encoding.
The iBeacon Format is defined in the configuration script by default for the TM-m30II-SL.
You can change this Packet Format to support Eddystone-UID or Eddystone-URL.
However, the TM-m30II-SL only supports single Advertising Data Packets.
You can change the settings using either of the following two methods.
• Changing settings using the Epson TM-m30II Utility for Windows (see the TM-m30II Utility User's Manual
for details)
• Changing settings using an HTTP Request
The method of changing settings via an HTTP Request is explained below.
Content Data Length Value Description
Length of this data 1 byte 02h
AD type 1 byte 01h Adtype: flags
Flags 1 byte 06h Fixed value (06h)
Length of this data 1 byte 1Ah Fixed value (1Ah)
AD type 1 byte FFh Adtype: Company identifier
Company Identifier code 2 bytes 004Ch Apple’s manufacture ID
iBeacon type 1 byte 02h Incomplete List of 16-bit service UUIDs
iBeacon length 1 byte 15h 15h=21=16+2+2+1
UUID 16 bytes - Default UUID = fac1ba2f-61a2-4d83-
9a8c-60087c232569
Major Number 2 bytes -
Minor Number 2 bytes -
Measured Power 1 byte BDh BDh: -67dB