Software User's Manual M00068501 EN
TM-T20II Software Installer Software User's Manual Cautions and Trademarks Cautions and Trademarks Cautions ❏ No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. ❏ The contents of this document are subject to change without notice. Please contact us for the latest information.
TM-T20II Software Installer Software User's Manual Cautions and Trademarks For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. !Caution: Provides information that must be observed to avoid damage to your equipment or a malfunction. Note: Provides important information and useful tips.
TM-T20II Software Installer Software User's Manual Contents Contents Uninstalling the EPSON Monitoring Tool. . . . Uninstalling the OPOS ADK. . . . . . . . . . . . . . Uninstalling the OPOS ADK for .NET. . . . . . . Uninstalling the JavaPOS ADK. . . . . . . . . . . . Cautions and Trademarks Cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ESC/POS Command System. . . . . . . . . . . . . . . . . For Safety. . . . . .
TM-T20II Software Installer Software User's Manual Contents USB. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ethernet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting Backup/Restore. . . . . . . . . . . . . . . . . . . . Saving the Printer Settings to a File. . . . . . . . . Restore the Settings to the Printer. . . . . . . . . . Acknowledgements. . . . . . . . . . . . . . . . . . . . . . . . 78 . 80 . 80 . 81 . 82 .
TM-T20II Software Installer Software User's Manual Overview Overview This chapter describes the specifications of TM-T20II Software & Documents Disc. TM-T20II Software Installer TM-T20II Software Installer allows you to install various drivers and utilities for the TM-T20II printer. Drivers and Utilities to be Installed Drivers ❏ Advanced Printer Driver Ver5 Windows printer driver. The following versions are provided. ❏ Advanced Printer Driver Ver.5.xx ❏ UPOS Stands for Unified Point of Service.
TM-T20II Software Installer Software User's Manual Overview Support OS The following lists the supported operating systems for running the TM-T20II drivers and utilities. ❏ Windows 10 (32 bit / 64 bit *1) ❏ Windows 8.
TM-T20II Software Installer Software User's Manual Overview Before TM-T20II driver is installed TM-T20II Software Installer A B C D Advanced Printer Driver Ver4.50 to 4.53 - ✓ ✓ ✓ Advanced Printer Driver Ver4.54 or later ✓ ✓ ✓ ✓ OPOS ADK Ver.2.67 former - ! - - OPOS ADK Ver.2.68 or later ✓ ! ✓ - current OPOS ADK for .NET Ver.1.11.8 former - - ! - OPOS ADK for .NET Ver.1.11.20 or later ✓ ✓ ! - JavaPOS ADK Ver.1.11.18 former - - - ! JavaPOS ADK Ver.1.11.
TM-T20II Software Installer Software User's Manual Overview ❏ Advanced Printer Driver Ver.5 Start - All Programs / All apps(Windows 8) - EPSON - EPSON Advanced Printer Driver 5 - EPSON APD5 TM-Txx Manual The Easy Install does not install the manuals. Install the manuals separately after finishing the Easy Install. U See “Installing Advanced Printer Driver Ver5 Manual” on page 19 ❏ OPOS ADK Start - All Programs / All apps(Windows 8) - OPOS - Manual ❏ OPOS ADK for .
TM-T20II Software Installer Software User's Manual Overview Item Description Starting the TM-T20II Utility Windows 8 Start - All apps - EPSON TM-T20II - EPSON TM-T20II Utility Windows 7 Start - All Programs - EPSON - TM-T20II Software - TM-T20II Utility Windows Vista Start - All Programs - EPSON - TM-T20II Software - TM-T20II Utility Windows XP Start - All Programs - EPSON - TM-T20II Software - TM-T20II Utility Uninstall a program Windows 8 Desktop - Sidebar Settings - Control Panel - Uninstall a pro
TM-T20II Software Installer Software User's Manual Overview A Insert the TM-T20II Software & Documents Disc to the computer. The TM-T20II Software Installer is automatically read and the EPSON TM-T20II Software Installer screen appears. Click the Manuals button. When the TM-T20II Software Installer is not automatically read, double click the TMInstallNavi.exe icon in the TM-T20II Software & Documents Disc. B The Manuals screen appears. Click the manual button you want to see.
TM-T20II Software Installer Software User's Manual Overview A Insert the TM-T20II Software & Documents Disc to the computer. The TM-T20II Software Installer is automatically read and the EPSON TM-T20II Software Installer screen appears. Click the Support button. When the TM-T20II Software Installer is not automatically read, double click the TMInstallNavi.exe icon in the TM-T20II Software & Documents Disc. B The Support Information screen appears. Click the button of your area.
TM-T20II Software Installer Software User's Manual Installation Installation This chapter describes how to install the printer drivers and conduct a test print after the installation. The uninstallation procedure is also provided. U See “Uninstallation” on page 36 !Caution: ❏ Install with administrator privileges. ❏ Close all running applications before the installation. ❏ If your printer is a serial type, and your OS is Windows 2000, you can not install Advanced Printer Driver using the installer.
TM-T20II Software Installer Software User's Manual Installation When the TM-T20II Software Installer is not automatically read, double click the TMInstallNavi.exe icon in the TM-T20II Software & Documents Disc. B The License Agreement screen appears. Read the content and select the I accept the terms in the license agreement. Then click the Next button. C The Select Installation Type screen appears. Click the Easy Install button. D The Communication Port Settings screen appears.
TM-T20II Software Installer Software User's Manual Installation E Click the Serial port button. Configure the communication settings, then click the Next button. Proceed to Step 8. Select the COM port, Bits per second, Data bits, Parity and Stop bits. Note: The driver's serial communication setting should be the same as that of the printer. F Click the Ethernet button. When printer is already networked Proceed to Step 7.
TM-T20II Software Installer Software User's Manual Installation G H Configure the IP address of the printer on IP Address and then click the Next button. Proceed to Step 8. When configuring the network setting after installing the driver, assign the printer driver port IP address you configure here to the printer, or change the printer driver port IP address to the one that will be set to the printer. The Start Installation screen appears. The driver and utility to be installed are listed.
TM-T20II Software Installer Software User's Manual Installation I The Connect Printer screen appears. Connect the computer to the printer, and turn the printer on. When the USB connection between the computer and printer is established, a pop-up message; Installing device driver software appears on the task tray, and the setup is automatically started. Proceed to Step 10 when the setting is finished.
TM-T20II Software Installer Software User's Manual Installation This is the end of the printer driver installation. For information on how to print using the printer driver. U See “Using the Printer Driver” on page 41 Network Address Setting for Ethernet Printer If you are using an Ethernet connection, configure the IP address using the EpsonNet Config. A Start the EpsonNet Config. B The EpsonNet Config screen appears. C Select the printer you want to configure, then click the Configuration button.
TM-T20II Software Installer Software User's Manual Installation E Configure the printer IP address. Then click the Transmit button. F The confirmation screen appears. Click the Yes button. G The configured settings are sent to the printer. After approx. 30 seconds, the completion screen appears. Select the Manual and Set using PING. Then configure the IP Address, Subnet Mask and Default Gateway. Click the OK button. H Confirm the settings on the EpsonNet Config screen.
TM-T20II Software Installer Software User's Manual Installation C The Update Software screen appears. Click the Next button. D The Select Software screen appears. Check the Sample and Manual checkbox and click the Next button. E The Start Installation screen appears. Click the Install button. F The EPSON APD5 Sample&Manual - InstallShield Wizard screen appears, click the Next button. G The License Agreement screen appears.
TM-T20II Software Installer Software User's Manual Installation B The property screen of the printer appears. Select the Ports tab and then click the Configure Port... button. C The Configure Port screen appears. Set a configure port while referring to the screen and click the OK button. D The display returns to the Properties screen. When you click the OK button, the changes you made become effective.
TM-T20II Software Installer Software User's Manual Installation Custom Install !Caution: ❏ When installing, connect just one printer. Do not connect multiple printers. ❏ When you are prompted whether to restart the computer during the installation, select No and continue the installation. Restart the computer and the printer after all the installation is finished. If you select Yes and restart the computer during the installation, the rest of the drivers will not be installed.
TM-T20II Software Installer Software User's Manual Installation C The Select Installation Type screen appears. Click the Custom Install button. D The Select Software screen appears. Check the items you want to install from the list. After this step, follow the installation procedure for each item. Installing the Printer Driver The printer driver can also be installed with Easy Install in the TM-T20II Software & Documents Disc.
TM-T20II Software Installer Software User's Manual Installation D The License Agreement screen is displayed. After checking the contents and selecting Agree, click Install. E The Printer Registration screen appears. F The Register, Change and Delete EPSON TM Printer screen is displayed. G Set the followings from 2. Printer. Installation of Advanced Printer Driver Ver.5 begins. Here, connect the printer to the computer and turn the printer's power on. Click Next. From 1.
TM-T20II Software Installer Software User's Manual Installation Port type Item COM Description Communicate with serial port. Set the following communication setting. Port Specify the number of serial port used for connecting the printer. Baud Rate Specify the baud rate. Parity Specify the parity. Stop Bits Specify the stop bits. Flow Control Specify the method of data flow between the computer and the printer. Data Bits Specify the data bits. USB Communicate with USB port.
TM-T20II Software Installer Software User's Manual Installation J When the printer is registered, the screen comes up as shown below. K After confirming the test page printing of Windows, click Next under 5. Complete. L The Installation Complete screen appears. M Click Yes. Test page printing of Windows is carried out. Click Close to finish the installation. When the installation is completed, the Installation Finished screen appears. When conducting test print: Click the Printing Test button.
TM-T20II Software Installer Software User's Manual Installation Installing the OPOS ADK A Insert the TM-T20II Software & Documents Disc into the computer and follow the steps. U See “Displaying the Select Software Screen” on page 22 B Check the OPOS ADK Ver. x.xx. Clear the check box for the items you do not want to install. Click the Next button. C The Start Installation screen appears. The driver and utility to be installed are listed. Click the Install button to start the installation.
TM-T20II Software Installer Software User's Manual Installation L When the installation is completed, the Installation Finished screen appears. Then click the Finish button to end the installation. This is the end of the OPOS ADK installation. Installing the OPOS ADK for .NET Note: To install the OPOS ADK for .NET, Microsoft .NET Framework and Microsoft POS for .NET are required. Install Microsoft .NET Framework and Microsoft POS for .NET Ver.1.11 beforehand.
TM-T20II Software Installer Software User's Manual Installation H The Setup Type screen appears. Select the port and click the Next button. I The Start Copying Files screen appears. Click the Next button to start the installation. J The InstallShield Wizard Complete screen appears. Click the Finish button. K When the installation is completed, the Installation Finished screen appears. Then click the Finish button to end the installation. This is the end of the OPOS ADK for .NET installation.
TM-T20II Software Installer Software User's Manual Installation D The EPSON JavaPOS ADK x.xx.x screen appears. Select the language and then click the OK button. E The Introduction screen appears. Click the Next button. F The License Agreement screen appears. Read the content and select the I accept the terms in the License Agreement. Click the Next button. G The Choose JVM screen appears. Click the Next button. H The Choose Install Set screen appears.
TM-T20II Software Installer Software User's Manual Installation N When the installation is completed, the Installation Finished screen appears. Then click the Finish button to end the installation. This is the end of the JavaPOS ADK installation. Installing the Utility The utility can also be installed with Easy Install on the TM-T20II Software & Documents Disc.
TM-T20II Software Installer Software User's Manual Installation D TM-T20II Utility is installed. Proceed to Step 12 if you do not install any other utility or driver. The installation is started without displaying any other screens. E EpsonNet Config is installed. F EPSON Monitoring Tool is installed. The installation is started without displaying any other screens. Proceed to Step 12 if you do not install any other utility or driver.
TM-T20II Software Installer Software User's Manual Installation If you restarted the computer, there's no need to proceed to Step 12, but the installation is complete. !Caution If the restart of your PC is requested on the InstallShield Wizard Complete screen, be sure to select Yes, I want to restart my computer now. M When the installation is completed, the Installation Finished screen appears. When exiting the installation: Uncheck the Run TM-T20II Utility (the box is unchecked by default).
TM-T20II Software Installer Software User's Manual Installation A In Windows2000's Printers, double click Add Printer. The Add Printer wizard starts up. B Follow the instructions shown on the screen. Select Local Printer, and turn off Automatically detect and install my Plug and Play printer. C Select a COM port to connect the printer. D Select Have Disk then Browse, and then select the following INF files on the CD-ROM. root/Windows/Advanced Printer Driver/V5_INF/Driver/EA5INSTMT20II.
TM-T20II Software Installer Software User's Manual Installation C The Update Software screen appears. The system is checked and existing driver and its version are displayed. Click the Next button. D The Select Printer Language (Resident Character) screen appears. Select the language of your printer and click the Next button. E The Select Software screen appears. Check the checkbox for the drivers and utilities you want to install and uncheck the checkbox for those you do not need.
TM-T20II Software Installer Software User's Manual Installation Note: If you select more than one drivers to install them under Windows 2000, you will be prompted that this may cause the printer to malfunction. Under Windows 2000, you can install only one driver. G The Start Installation screen appears. Check that the listed items to be installed are correct, and click the Install button. H When the installation is finished, the Installation Finished screen appears.
TM-T20II Software Installer Software User's Manual Installation B Select Start - Control Panel - Uninstall a program - EPSON Advanced Printer Driver for TM-T20II Ver.5 and click Uninstall. C The uninstallation confirmation screen appears. Click the Yes button. D The uninstallation confirmation screen for model specific utility is displayed. Click Yes when not using the model specific utility with other drivers and applications. Click No when not uninstalling. The Advanced Printer Driver Ver.
TM-T20II Software Installer Software User's Manual Installation Uninstall the EpsonNet Config A Select Start - Control Panel - Uninstall a program - EpsonNet Config. Click Uninstall. For information of the differences in screen selections based on the OS versions. U See “Differences Depending on the OS” on page 9 When the User Account Control screen appears, click the Continue button. B The EpsonNet Config uninstallation confirmation screen appears. Click the Yes button.
TM-T20II Software Installer Software User's Manual Installation C The Uninstall Complete window appears. click on the Finish button. D The Uninstall or change a program window appears. Double-click on EpsonNet SDK for Windows. E The Uninstall Confirmation window appears. click on the Yes button. The EpsonNet SDK for Windows will be uninstalled. F The Uninstall Complete window appears. click on the Finish button.
TM-T20II Software Installer Software User's Manual Installation B Select Start - Control Panel - Uninstall a program - EPSON OPOS ADK for .NET x.x.x. Click Uninstall. For information of the differences in screen selections based on the OS versions. U See “Differences Depending on the OS” on page 9 When the User Account Control screen appears, click the Continue button. C The EPSON OPOS ADK for .NET uninstallation confirmation screen appears. Click the Yes button.
TM-T20II Software Installer Software User's Manual Using the Printer Driver Using the Printer Driver This chapter explains how to use the major functions of the printer driver. Printer Driver Access Methods and the Application Range Depending on how you access the printer driver, the application range of the settings you make on the printer driver varies.
TM-T20II Software Installer Software User's Manual Using the Printer Driver Accessing from the Printer Driver's Properties Accessing from the Application's Print Setting Menu Language for Displaying Properties The language used in the Advanced Printer Driver screen and Help can be selected from 24 languages. Selecting the language that is easiest for you to understand will help you correctly configure the settings in the Advanced Printer Driver.
TM-T20II Software Installer Software User's Manual Using the Printer Driver A Select the Language tab from Printing Preferences. B Select the language that you wish to use in the screens and Help from the Select language pull-down list. When finished, click the OK button. The languages that can be selected are shown below.
TM-T20II Software Installer Software User's Manual Using the Printer Driver B Select a cut and paper feed method displayed in the Preset option list and click OK. Select using the illustration of paper feed and cut displayed in Illustration for your reference. Note: ❏ Feed: Paper is fed to the auto-cutter's cutting position after printing a document. ❏ No Feed: Paper is not fed after printing a document.
TM-T20II Software Installer Software User's Manual Using the Printer Driver Item Timing Action C Description Start of Document At the beginning of document printing Start of Page At the beginning of each page in the document End of Page At the end of each page in the document End of Document At the end of document printing Feed to cut position before cutting When checked, paper is fed to the cutting position of auto-cutter. Cutting method Auto-cutter will not act when No cut is selected.
TM-T20II Software Installer Software User's Manual Using the Printer Driver B From the Peripherals pull down list, select the combination of peripheral device to be connected to the printer. C Select the timing to set the peripheral device settings. U See “Setting of Peripheral Device” on page 46 D Confirm Current settings and click OK. Setting of Peripheral Device Settings may be different depending on peripheral devices. Note: Cash drawer and external buzzer cannot be used simultaneously.
TM-T20II Software Installer Software User's Manual Using the Printer Driver Peripherals Setting Value Description External Buzzer Turn off External buzzer does not sound. Turn on External buzzer sounds. Pattern Specify buzzer sound pattern. Count Specify buzzer sound frequency. Logo Printing Logo can be printed at the beginning and the end of printing. There are 2 printing methods.
TM-T20II Software Installer Software User's Manual Using the Printer Driver C Select the position where the logo is printed. D Click Select Image to specify the logo to print. E The Logo Edit screen is displayed. Refer to the preview at the upper part of the screen and edit the image data for logo.When editing is done, click OK. Select the printing position from Start of Document / End of Document / Start of Page / End of Page. Settings are described below.
TM-T20II Software Installer Software User's Manual Using the Printer Driver Item Description Half toning Setup the half-toning type. Select from Dither / Error Diffusion / None. Brightness Setup the brightness. Select from 5 levels. Density Setup the printing density. F Click Set. G When printing, the logo is printed at the position set in the APD5 utility. The logo is registered to the driver.
TM-T20II Software Installer Software User's Manual Using the Printer Driver A Select User Defined Paper of the APD5 utility to setup user defined paper. Item Description Paper Name Name of the user defined paper. This name is displayed in Printing Preferences - Layout. Unit Specify the unit for the paper width setting. Paper Size Specify the user defined paper size (width, height). Margin Specify the user defined paper size space (top, bottom, left, right).
TM-T20II Software Installer Software User's Manual Using the Printer Driver Barcode Printing Set a barcode font to the Advanced Printer Driver. Barcode can be printed without having barcode encoder in an application or preparing graphic data of barcode. High precision reading of barcode can be printed comparing to when the barcode data is set in an application. A Barcode font can be setup from Barcode of the APD5 utility. B Specify a barcode font to barcode data using the application.
TM-T20II Software Installer Software User's Manual Using the Printer Driver A 2 dimensional font can be set from 2-dimensional symbol of the APD5 utility. B Specify a 2 dimensional font to 2 dimensional data using the application. C 2 dimensional symbol is printed based on the settings of the APD5 utility. For detail, see Advanced Printer Driver Ver.5 Printer Manual. Coupon Printing APD5 provides the coupon printing function.
TM-T20II Software Installer Software User's Manual Using the Printer Driver Buzzer Settings Allows you to configure whether an external optional buzzer is used and the buzzer pattern settings. Configure as follows. A Click the Optinal Buzzer menu. B Select whether or not the buzzer is used. C Disable Buzzer Do not use the external buzzer. Go to step 4. Enable Buzzer Use the external buzzer. Go to step 3. Specify when the optional buzzer sounds and the buzzer pattern.
TM-T20II Software Installer Software User's Manual Using the Printer Driver D Setting Description When automatic paper cut activates: Configure the buzzer setting when automatic paper cutting takes place. When specified pulse 1 (2 pin) occurs: Configure the buzzer setting when the specified pulse is generated. When specified pulse 2 (5 pin) occurs: Configure the buzzer setting when the specified pulse is generated. Buzzer: Test the buzzer. Select a sound pattern.
TM-T20II Software Installer Software User's Manual TM-T20II Utility TM-T20II Utility This chapter explains how to use the TM-T20II Utility that configures this printer. Overview !Caution: While saving the settings, do not turn off the printer or terminate the connection with the printer. TM-T20II Utility provides the following functions.
TM-T20II Software Installer Software User's Manual TM-T20II Utility If you have checked Run TM-T20II Utility at Step 10 of Easy Install procedure, start from Step 2. A Select Start - All Programs - EPSON - TM-T20II Software - TM-T20II Utility. B The following screen appears. Select the printer to use and click the OK button. If you wish to change the language that appears in the TM-T20II Utility, click the Select Language button. If the printer is not displayed, click the Add Port button.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Adding a Communication Port and Starting the TM-T20II Utility Add a communication port as follows: A Select Start - All Programs - EPSON - TM-T20II Software - TM-T20II Utility. B The following screen appears. Click the Add Port button.
TM-T20II Software Installer Software User's Manual TM-T20II Utility C The Add Port screen appears. Configure the port to be added. Then, click the OK button. Note: ❏ If the communication with the port failed, an error message appears. In such case, you cannot add the port. Make sure the printer is connected properly and check your communication settings. ❏ Clicking the Communication test button displays the communication result on the screen. It does not conduct a test print.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Setting Description Port: Selects the parallel port of the computer you use. Search: Searches for available parallel ports. Virtual Port Settings Starts the Virtual Port Settings tool. For details, see the manual for the Virtual Port Settings tool. Communication test Runs a communication test. ❏ USB Setting Description Port: Selects the USB port you use. Search Searches for the available USB port(s).
TM-T20II Software Installer Software User's Manual TM-T20II Utility D The following screen appears again. Select the added port and click the OK button. E The TM-T20II Utility is started.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Current Settings Allows you to check the printer settings and the maintenance counter. Setting Description Storing Logos: Displays the number of stored logos and their sizes. Coupon Settings: *1 Displays the coupon settings. Paper Reduction Settings: Displays the paper reduction Enable/Disable setting. Automatic Paper Cut Settings: Displays the settings of the automatic paper cut function.
TM-T20II Software Installer Software User's Manual TM-T20II Utility ❏ USB I/F Setting Description USB Device: Displays the product name. USB Device Version: Displays the product version. USB ID: Displays the serial number. USB Information: Displays the character string configured to the interface for identification purpose. ❏ Ethernet I/F Setting Description Ethernet I/F: Displays the product name. MAC address: Displays the MAC address setting of the interface.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Maintenance counter Allows you to check the following counters and to reset some of them. The cumulative counter cannot be reset. ❏ Length of paper feed [km] ❏ Number of autocutter operations Times Operation Check Allows you to check the printer operation and communication between the printer and the driver. Configure as follows. A Click the Operation Check menu.
TM-T20II Software Installer Software User's Manual TM-T20II Utility B Click the button of the item you want to check. You can check the followings. ❏ Unit Test Setting Description Communication Test Checks if the communication between the computer and the printer is normal. Test Printing Makes a test print. To see if the printer prints correctly. Print Logo Prints the logo stored on the printer. Print Font Prints the fonts installed on the printer.
TM-T20II Software Installer Software User's Manual TM-T20II Utility This section describes how to configure logos to be stored on the printer. The utility allows you to print your logo already stored on the printer, but you cannot edit and restore it as a file. When using the OPOS to store your logo, U see “Storing Logos” on page 86. Storing Logos has the following functions. Setting Description Key Code List Displays the logos registered in the printer and the logos to be added in the printer.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Select Mode for Storing Logo has the following functions. The current setting is displayed below Storing Logos. Setting Description First Key-code Selection Mode Specifies the logo identifying code. Automatically set the key-code for the logo to be stored. If this is turned on, automatically sets Key-codes to the logos to be registered. If turned off, sets Key-codes when adding or editing logos.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Adding a Logo Add a logo as follows. A Click the Add button. B Specify the image data to be used as a logo. A file size of 2047 (W) x 831 (H) pixels (dots) or less can be specified, and the format can be bmp, jpeg, gif, or png. If the logo width is greater than the paper width, a warning message will appear. Click the OK button and reduce the logo size in the Logo Edit screen of step 3.
TM-T20II Software Installer Software User's Manual TM-T20II Utility C The Logo Edit screen appears. Edit the logo image while checking the image previewed on the upper portion of the screen. When finished, click the OK button. You can edit the followings. D Setting Description Image width Specifies the width to which the image is resized (in mm). Resize Specifies whether or not the image is resized.
TM-T20II Software Installer Software User's Manual TM-T20II Utility F After storing all the logo data to be added to the printer, check the indicator on the right side of the screen to see if the data size is acceptable to be stored on the printer, and then click the Store to Printer button. G The logo data is stored to the printer. The logo data are also saved in the logo store file (TLG file). This file is used when creating the printer setting file.
TM-T20II Software Installer Software User's Manual TM-T20II Utility C Store all the logos and add them to the printer altogether at once. In this way, the logo store file (TLG file) containing all the logo data is created. U See “Adding a Logo” on page 67 Paper Reduction Settings !Caution: The paper reduction settings may not reduce paper usage as specified when you print images such as logos or coupon tickets, or print in page mode.
TM-T20II Software Installer Software User's Manual TM-T20II Utility B Configure the following items referring to the preview on the right portion of the screen. Note: Settings other than Extra Upper Space Reduction and Extra Lower Space Reduction are disabled due to the Advanced Printer Driver being in graphics mode. C Setting Description Extra Upper Space Reduction Selects whether to reduce the upper margin or not.
TM-T20II Software Installer Software User's Manual TM-T20II Utility !Caution: ❏ If you set a logo here, the logo will be printed when you print coupons too. ❏ If you don't want to print the logo on coupons, set the logo printing during auto cut in coupon printing. (For details, refer to the TM-T20II Utility User's Manual.) Configure as follows. A Click the Automatic Paper Cut menu. B Click the item you want to check. Not use this function Disables the automatic paper cut function. Go to Step 4.
TM-T20II Software Installer Software User's Manual TM-T20II Utility C Configure the Print logo when paper is cut. Setting Description Top Logo Sets the logo that is printed at the top of the paper. Bottom Logo Condition Extra Upper Space Reduction: ❏ Key-code: Selects the Key-code of the logo to be printed. ❏ Alignment: Selects the logo print position. Sets the logo that is printed at the bottom of the paper. ❏ Key-code: Selects the Key-code of the logo to be printed.
TM-T20II Software Installer Software User's Manual TM-T20II Utility A Click the Printing Control menu. B Configure the following printing control items. Setting Description Paper width: Selects the paper width. Logo 180 dpi Emulation Mode: Enables or disables Logo 180 dpi Emulation Mode. Logo 180 dpi Emulation Mode allows you to print logos created for 180dpi printers on the same position and in the size when using TM-T20.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Note: If you make any of the following settings different from that of the printer driver, the printer driver setting is used. C ❏ Print density ❏ Print speed ❏ Paper width Click the Set button. The settings are reflected to the printer. Font Settings Allows you to configure the printer font and international character set. Configure as follows. Note: ❏ When using the Advanced Printer Driver Ver. 5.
TM-T20II Software Installer Software User's Manual TM-T20II Utility C Click the Set button. The settings are reflected to the printer. Click the Test print button to print the configured printer font pattern. Buzzer Settings Allows you to configure whether an external optional buzzer is used and the buzzer pattern settings. Configure as follows. A Click the Optional Buzzer menu. B Select whether or not the buzzer is used. Disable Buzzer Do not use the external buzzer. Go to step 4.
TM-T20II Software Installer Software User's Manual TM-T20II Utility C D Specify when the optional buzzer sounds and the buzzer pattern. Setting Description When an error occurs: Configure the buzzer setting when an error occurs. When automatic paper cut activates: Configure the buzzer setting when automatic paper cutting takes place. When specified pulse 1 (2 pin) occurs: Configure the buzzer setting when the specified pulse is generated.
TM-T20II Software Installer Software User's Manual TM-T20II Utility C Click the Set button. The settings are reflected to the printer. Serial Configures the serial communication. Setting Description Communication speed: Selects the communication speed. Parity: Configures the parity. Data Bit: Configures the data bit. Stop Bit: Configures the stop bit. Flow control: Configures the flow control. USB Configures the USB class. Note: ❏ When using the UPOS or Advanced Printer Driver Ver. 3.
TM-T20II Software Installer Software User's Manual TM-T20II Utility ❏ Printer Class: Configures the printer to the printer class. ❏ Vender Class: Configures the printer to the vender class. If you change the USB class from Vender Class to Printer Class, the printer becomes a Printer Class device. The computer detects the printer as a new Printer Class device and creates a new port. Using the newly created port, you can print but cannot use the EPSON Status API.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Ethernet Starts EpsonNet Config, and configures network addresses. Setting Description Advanced settings Starts EpsonNet Config when the Advanced settings button is clicked. Setting Backup/Restore Allows you to save the printer settings to a file and to restore the stored settings to the printer.
TM-T20II Software Installer Software User's Manual TM-T20II Utility !Caution: ❏ On the environment with no Advanced Printer Driver, OPOS, OPOS for .NET, or JavaPOS installed, Automatic Restore Settings is disabled. ❏ Automatic Restore Settings cannot be saved or restored. If you want to copy coupon settings on another printer, refer to TM-T20II Utility User's Manual. Saving the Printer Settings to a File Save the settings as follows: A Click the Backup/Restore menu.
TM-T20II Software Installer Software User's Manual TM-T20II Utility D The Select Logo File screen appears. The most recently saved logo filename will appear. Click the OK button. E Specify the filename and backup location in the next screen and save the file. If you wish to change the file to be saved, click the Browse button. Restore the Settings to the Printer Restore the settings as follows: A Click the Backup/Restore.
TM-T20II Software Installer Software User's Manual TM-T20II Utility Automatic Restore Settings Configures the automatic restore settings. Setting Description Automatically restore the settings when replaced with a new printer. To have printer settings automatically restored using the previously created backup file when the printer fails and is replaced with a new printer.
TM-T20II Software Installer Software User's Manual TM-T20II Utility This software is provided "as is," without warranty of any kind, express or implied. In no event shall Info-ZIP or its contributors be held liable for any direct, indirect, incidental, special or consequential damages arising out of the use of or inability to use this software.
TM-T20II Software Installer Software User's Manual Application Development Information Application Development Information This chapter explains how to control this printer and gives information useful for printer application development. How to Control the Printer The printer is controlled by the drivers or ESC/POS commands.
TM-T20II Software Installer Software User's Manual Application Development Information ❏ User's Manual ❏ Application Development Guide ❏ UnifiedPOS Retail Peripheral Architecture* ❏ Sample Program Guide EPSON OPOS ADK for .NET ❏ OPOS ADK for .
TM-T20II Software Installer Software User's Manual Application Development Information ❏ OPOS setting Using the OPOS SetupPOS, select Bitmap tab on the Device Specific Settings screen, and uncheck the checkbox for NVRAM. ❏ Storing logos in the printer Use TM-T20II Utility to store logos in the printer. Download Drivers, utilities, and manuals can be downloaded from one of the following URLs. For customers in North America, go to the following web site: http://www.epsonexpert.
