User Manual
Table Of Contents
- Copyrights and Trademarks
- Contents
- Notes on Manuals
- Introducing the Software
- Basic Operations
- Using the Optional Hard Disk Unit
- Using the Printer Driver(Windows)
- Using the Printer Driver(Mac)
- Printing Varieties
- Printing with Darker Tones of Black (Black Enhance Overcoat)
- Correct color and print
- Printing Black and White Photos
- Borderless Printing
- Enlarged/Reduced Printing
- Multi-Page Printing
- Poster Printing (Enlarge to cover several sheets and print - Windows only)
- Printing at Non-Standard Sizes
- Banner printing (on roll paper)
- Layout Manager(Windows Only)
- Color Management Printing
- Menu List
- Maintenance
- Problem Solver
- What to do When a Message is Displayed
- SpectroProofer Error
- When an Error Message and Error Code are Displayed
- Troubleshooting
- You cannot print (because the printer does not work)
- The printer does not turn on.
- The printer turns off automatically.
- The printer driver is not installed properly (Windows).
- The printer driver is not installed properly (Mac).
- The printer is not communicating with the computer.
- You cannot print under the network environment.
- The printer has an error.
- The printer stops printing.
- Your problem is not listed here.
- The printer sounds like it is printing, but nothing prints
- The prints are not what you expected
- Print quality is poor, uneven, too light, or too dark.
- The color is not exactly the same as another printer.
- I am worried about the print quality at the leading edge of the paper
- The print is not positioned properly on the media.
- Vertical ruled lines are misaligned.
- The printed surface is scuffed or soiled.
- Cleaning around the print head and caps
- The paper is creased.
- Print outs are wrinkled
- The reverse side of the printed paper is soiled.
- Too much ink is fired.
- Margins appear in borderless printing.
- Feeding or ejecting problems
- Others
- The control panel display keeps turning off.
- Color ink runs out quickly even when printing in the Black&White mode or when printing black data.
- The paper is not cut cleanly.
- A light is visible inside the printer.
- The administrator password has been lost
- Head cleaning is performed automatically
- The noise made by the drying fan during color measurement is slightly louder than in previous models.
- When an error occurs during color measurement (when using the SpectroProofer mounter), the colors do ...
- Cannot update the firmware for the printer
- Printing stops when printing in a VPN (Virtual Private Network) environment
- The printer turned off due to a power cut
- You cannot print (because the printer does not work)
- Appendix
- Where To Get Help
- Technical Support Web Site
- Contacting Epson Support
- Before Contacting Epson
- Help for Users in North America
- Help for Users in Europe
- Help for Users in Taiwan
- Help for Users in Australia/New Zealand
- Help for Users in Singapore
- Help for Users in Thailand
- Help for Users in Vietnam
- Help for Users in Indonesia
- Help for Users in Hong Kong
- Help for Users in Malaysia
- Help for Users in India
- Help for Users in the Philippines
Settings item Setting/Additional Explanation
Paper Source Settings
Roll Paper Setup
Auto Loading On, Off
Cut Settings
Auto Cut On, Off
Print Cutting Guideline On, Off
If Auto Cut is set to Off, you can choose whether or not (On/Off) to print
cutting lines on roll paper. Cutting lines are not printed if Auto Cut is set to
On or when printing cut sheets or poster board.
Wait for Cut Between Pages On, Off
Cut for Borderless Print Two Cuts, One Cut
Quick Cut On, Off
Cut Mode Normal, Quiet
Margin Refresh On, Off
Before printing with borders, select whether or not (On/Off) to
automatically cut the leading edge to remove ink stains that may have
been left by previous borderless printing.
Roll End Option Continue, Stop Printing, Reprint
Select the action to perform for a roll after replacement: print the
remaining data (Continue) / do not print (Stop Printing) / print again from
the beginning (Reprint).
Reprint is only available when the optional hard disk unit is installed.
Take-up After Cut On, Off
This item is only displayed when the take-up reel unit is connected.
U “Removing Paper from the Auto Take-up Reel Unit” on page 41
Error Notice
Paper Size Notice On, Off
Paper Type Notice On, Off
Detect Paper Meandering On, Off
Platen Gap Offset Standard, Wide, Wider, Widest
Custom Paper Setting
01-30 Display Registered Number & Registered Media Name
From the printer, you cannot change paper setting information registered
using the driver or other software.
Change Name Displays the media name registration screen
Change Reference Paper Displays the reference paper type
SC-P9500 Series/SC-P7500 Series User's Guide
Menu List
107