User Manual
Table Of Contents
- Copyrights and Trademarks
- Contents
- Notes on Manuals
- Introducing the Software
- Basic Operations
- Using the Optional Hard Disk Unit
- Using the Printer Driver(Windows)
- Using the Printer Driver(Mac)
- Printing Varieties
- Printing with Darker Tones of Black (Black Enhance Overcoat)
- Correct color and print
- Printing Black and White Photos
- Borderless Printing
- Enlarged/Reduced Printing
- Multi-Page Printing
- Poster Printing (Enlarge to cover several sheets and print - Windows only)
- Printing at Non-Standard Sizes
- Banner printing (on roll paper)
- Layout Manager(Windows Only)
- Color Management Printing
- Menu List
- Maintenance
- Problem Solver
- What to do When a Message is Displayed
- SpectroProofer Error
- When an Error Message and Error Code are Displayed
- Troubleshooting
- You cannot print (because the printer does not work)
- The printer does not turn on.
- The printer turns off automatically.
- The printer driver is not installed properly (Windows).
- The printer driver is not installed properly (Mac).
- The printer is not communicating with the computer.
- You cannot print under the network environment.
- The printer has an error.
- The printer stops printing.
- Your problem is not listed here.
- The printer sounds like it is printing, but nothing prints
- The prints are not what you expected
- Print quality is poor, uneven, too light, or too dark.
- The color is not exactly the same as another printer.
- I am worried about the print quality at the leading edge of the paper
- The print is not positioned properly on the media.
- Vertical ruled lines are misaligned.
- The printed surface is scuffed or soiled.
- Cleaning around the print head and caps
- The paper is creased.
- Print outs are wrinkled
- The reverse side of the printed paper is soiled.
- Too much ink is fired.
- Margins appear in borderless printing.
- Feeding or ejecting problems
- Others
- The control panel display keeps turning off.
- Color ink runs out quickly even when printing in the Black&White mode or when printing black data.
- The paper is not cut cleanly.
- A light is visible inside the printer.
- The administrator password has been lost
- Head cleaning is performed automatically
- The noise made by the drying fan during color measurement is slightly louder than in previous models.
- When an error occurs during color measurement (when using the SpectroProofer mounter), the colors do ...
- Cannot update the firmware for the printer
- Printing stops when printing in a VPN (Virtual Private Network) environment
- The printer turned off due to a power cut
- You cannot print (because the printer does not work)
- Appendix
- Where To Get Help
- Technical Support Web Site
- Contacting Epson Support
- Before Contacting Epson
- Help for Users in North America
- Help for Users in Europe
- Help for Users in Taiwan
- Help for Users in Australia/New Zealand
- Help for Users in Singapore
- Help for Users in Thailand
- Help for Users in Vietnam
- Help for Users in Indonesia
- Help for Users in Hong Kong
- Help for Users in Malaysia
- Help for Users in India
- Help for Users in the Philippines
c
Important:
The commercially available media types, such as
those shown below, may not be cut cleanly by the
built-in cutter. Furthermore, cutting the following
media types may damage or reduce the lifetime of
the built-in cutter.
❏ Fine art paper
❏ Canvas
❏ Vinyl
❏ Matte poster board
❏ Adhesive paper
❏ Banner media
Cut these media types with commercially available
scissors or a cutter in the following manner:
With the front cover closed, hold down the X -
Forward buttons on the control panel while viewing
the inside of the printer until the cutting position
emerges from below the front cover. Cut the paper
using scissors or a third-party cutter.
Setting Auto Cut
You can specify the method either on the control panel
or the printer driver. Note, however, that the setting
selected with the printer driver takes priority when the
printer driver is used.
Note:
❏ Disable the auto cut settings in the printer and the
printer driver when using the optional auto take-up
reel unit.
❏ It may take a while to cut the roll paper.
Setting on the computer
Set Auto Cut from the Roll Paper Option in the printer
driver's Properties (or Printing preferences) screen.
Setting from the printer
Set this in General Settings - Printer Settings - Paper
Source Settings - Roll Paper Setup - Cut Settings -
Auto Cut from the control panel.
Manual cut method
When Off is selected in the printer driver or Off is
selected for Auto Cut in the control panel, the paper can
be cut in any location after printing as described below.
A
With the front cover closed, hold down the X -
Forward or Backward button on the control
panel while viewing the inside of the printer until
the cutting position reaches the position of the
label.
Note:
To cut the paper using the built-in cutter, the
distance from the cutting position to the edge of the
paper needs to be 60 to 127 mm. The necessary
length differs depending on the paper type and
cannot be changed. If the necessary length has not
been reached, paper is fed automatically leaving a
margin. Use a commercially available cutter to
remove the unnecessary margin.
B
Touch Cut.
A confirmation screen is displayed. Press the Cut
button to cut using the built-in cutter.
Removing Roll Paper
This section describes how to remove and store roll
paper after printing. The pressure roller may leave
impressions on paper that is left in the printer.
SC-P9500 Series/SC-P7500 Series User's Guide
Basic Operations
26