User Manual
Table Of Contents
- Copyrights and Trademarks
- Contents
- Notes on Manuals
- Introducing the Software
- Basic Operations
- Using the Optional Hard Disk Unit
- Using the Printer Driver(Windows)
- Using the Printer Driver(Mac)
- Printing Varieties
- Printing with Darker Tones of Black (Black Enhance Overcoat)
- Correct color and print
- Printing Black and White Photos
- Borderless Printing
- Enlarged/Reduced Printing
- Multi-Page Printing
- Poster Printing (Enlarge to cover several sheets and print - Windows only)
- Printing at Non-Standard Sizes
- Banner printing (on roll paper)
- Layout Manager(Windows Only)
- Color Management Printing
- Menu List
- Maintenance
- Problem Solver
- What to do When a Message is Displayed
- SpectroProofer Error
- When an Error Message and Error Code are Displayed
- Troubleshooting
- You cannot print (because the printer does not work)
- The printer does not turn on.
- The printer turns off automatically.
- The printer driver is not installed properly (Windows).
- The printer driver is not installed properly (Mac).
- The printer is not communicating with the computer.
- You cannot print under the network environment.
- The printer has an error.
- The printer stops printing.
- Your problem is not listed here.
- The printer sounds like it is printing, but nothing prints
- The prints are not what you expected
- Print quality is poor, uneven, too light, or too dark.
- The color is not exactly the same as another printer.
- I am worried about the print quality at the leading edge of the paper
- The print is not positioned properly on the media.
- Vertical ruled lines are misaligned.
- The printed surface is scuffed or soiled.
- Cleaning around the print head and caps
- The paper is creased.
- Print outs are wrinkled
- The reverse side of the printed paper is soiled.
- Too much ink is fired.
- Margins appear in borderless printing.
- Feeding or ejecting problems
- Others
- The control panel display keeps turning off.
- Color ink runs out quickly even when printing in the Black&White mode or when printing black data.
- The paper is not cut cleanly.
- A light is visible inside the printer.
- The administrator password has been lost
- Head cleaning is performed automatically
- The noise made by the drying fan during color measurement is slightly louder than in previous models.
- When an error occurs during color measurement (when using the SpectroProofer mounter), the colors do ...
- Cannot update the firmware for the printer
- Printing stops when printing in a VPN (Virtual Private Network) environment
- The printer turned off due to a power cut
- You cannot print (because the printer does not work)
- Appendix
- Where To Get Help
- Technical Support Web Site
- Contacting Epson Support
- Before Contacting Epson
- Help for Users in North America
- Help for Users in Europe
- Help for Users in Taiwan
- Help for Users in Australia/New Zealand
- Help for Users in Singapore
- Help for Users in Thailand
- Help for Users in Vietnam
- Help for Users in Indonesia
- Help for Users in Hong Kong
- Help for Users in Malaysia
- Help for Users in India
- Help for Users in the Philippines
D
Remove the optional auto take-up reel unit or
SpectroProofer mounter if they are installed.
U Setup Guide (booklet) supplied with
optional items
E
Unlock the casters.
F
Move the printer.
c
Important:
Use the casters to move the printer indoors a
short distance over a level floor. They can not
be used for transport.
Notes on Transporting
Make the following preparations in advance before
transporting the printer.
❏ Touch Maintenance - Keeping/Transporting
Preparation - Personal Transport Preparation
from the control panel. Ink is discharged. When the
ink has been discharged, the printer turns off.
❏ Disconnect all of the cables.
❏ Remove any paper.
❏ Remove any optional components if they are
installed.
To remove the optional components, see the Setup
guide included with each of them, and then reverse
the attachment procedure.
Furthermore, repack it using the original box and
packing materials to protect it from shock and
vibration.
When packing, make sure you install protective
material to secure the print head.
See the "Setup Guide" (booklet) supplied with the
printer for the installation method, and install in the
original location before the printer was removed.
Caution:
❏ The printer is heavy. When you pack or move
the printer, use four or more people when
carrying it. Also, make sure there is another
person to guide the people carrying the printer.
❏ When you lift the printer, maintain a natural
posture.
❏ When you lift the printer, place your hands at
the locations indicated in the following
illustration.
If you lift the printer while holding other
sections, you may be injured. For example, you
may drop the printer or your fingers may be
pinched when lowering the printer.
SC-P9500 Series/SC-P7500 Series User's Guide
Appendix
171