User Manual
Table Of Contents
- Copyrights and Trademarks
- Contents
- Notes on Manuals
- Introducing the Software
- Basic Operations
- Using the Optional Hard Disk Unit
- Using the Printer Driver(Windows)
- Using the Printer Driver(Mac)
- Printing Varieties
- Printing with Darker Tones of Black (Black Enhance Overcoat)
- Correct color and print
- Printing Black and White Photos
- Borderless Printing
- Enlarged/Reduced Printing
- Multi-Page Printing
- Poster Printing (Enlarge to cover several sheets and print - Windows only)
- Printing at Non-Standard Sizes
- Banner printing (on roll paper)
- Layout Manager(Windows Only)
- Color Management Printing
- Menu List
- Maintenance
- Problem Solver
- What to do When a Message is Displayed
- SpectroProofer Error
- When an Error Message and Error Code are Displayed
- Troubleshooting
- You cannot print (because the printer does not work)
- The printer does not turn on.
- The printer turns off automatically.
- The printer driver is not installed properly (Windows).
- The printer driver is not installed properly (Mac).
- The printer is not communicating with the computer.
- You cannot print under the network environment.
- The printer has an error.
- The printer stops printing.
- Your problem is not listed here.
- The printer sounds like it is printing, but nothing prints
- The prints are not what you expected
- Print quality is poor, uneven, too light, or too dark.
- The color is not exactly the same as another printer.
- I am worried about the print quality at the leading edge of the paper
- The print is not positioned properly on the media.
- Vertical ruled lines are misaligned.
- The printed surface is scuffed or soiled.
- Cleaning around the print head and caps
- The paper is creased.
- Print outs are wrinkled
- The reverse side of the printed paper is soiled.
- Too much ink is fired.
- Margins appear in borderless printing.
- Feeding or ejecting problems
- Others
- The control panel display keeps turning off.
- Color ink runs out quickly even when printing in the Black&White mode or when printing black data.
- The paper is not cut cleanly.
- A light is visible inside the printer.
- The administrator password has been lost
- Head cleaning is performed automatically
- The noise made by the drying fan during color measurement is slightly louder than in previous models.
- When an error occurs during color measurement (when using the SpectroProofer mounter), the colors do ...
- Cannot update the firmware for the printer
- Printing stops when printing in a VPN (Virtual Private Network) environment
- The printer turned off due to a power cut
- You cannot print (because the printer does not work)
- Appendix
- Where To Get Help
- Technical Support Web Site
- Contacting Epson Support
- Before Contacting Epson
- Help for Users in North America
- Help for Users in Europe
- Help for Users in Taiwan
- Help for Users in Australia/New Zealand
- Help for Users in Singapore
- Help for Users in Thailand
- Help for Users in Vietnam
- Help for Users in Indonesia
- Help for Users in Hong Kong
- Help for Users in Malaysia
- Help for Users in India
- Help for Users in the Philippines
Interface Specifications
Ethernet
*1
Standards
IEEE802.3u (100BASE-TX)
IEEE802.3ab (1000BASE-T)
IEEE802.3az (Energy Efficient
Ethernet)
*2
Network Printing
Protocols/Func-
tions
*3
EpsonNet Print (Windows)
Standard TCP/IP (Windows)
WSD Printing (Windows)
Bonjour Printing (Mac)
IPP Printing (Mac)
Printing from FTP client
Security Protocols SSL/TLS (HTTPS Server/Client,
IPPS)
IEEE802.1X
IPsec/IP Filtering
SMTPS (STARTTLS, SSL/TLS)
SNMPv3
*1 Use a category 5 or higher STP (Shielded twisted pair) cable.
*2 The connected device should comply with IEEE802.3az
standards.
*3 EpsonNet Print supports IPv4 only. The others support both
IPv4 and IPv6.
Ink Specifications
Type Special ink cartridges
Pigment ink (Cyan, Vivid Magenta, Yellow, Light
Cyan, Vivid Light Magenta, Orange,
Green, Violet, Photo Black, Matte
Black, Gray, Light Gray)
Use by date See the date printed on the
package (at normal temperature)
Print quality guar-
antee expiry
One year (after installing to the
printer)
Storage temperature
Uninstalled -20 to 40˚C (Within four days at -20
˚C, within a month at 40 ˚C)
Installed -10 to 40˚C (Within four days at -10
˚C, within a month at 40 ˚C)
Transporting -20 to 60˚C (Within four days at -20
˚C, within a month at 40 ˚C, within
72 hours at 60 ˚C)
Cartridge capacities 700 ml, 350 ml, 150 ml
c
Important:
❏ We recommend that you remove and shake the
installed ink cartridges once every six months to
ensure good print quality.
❏ The ink freezes if left at below -20 ˚C for a long
time. If it does freeze, leave it at room
temperature (25˚C) for at least four hours.
❏ Do not refill the ink cartridges.
SC-P9500 Series/SC-P7500 Series User's Guide
Appendix
177