user manual
Table Of Contents
- EPSON EPL-6200/EPL-6200L
- Contents
- Product Description
- 1.1 Outline
- 1.2 Basic Specifications
- 1.2.1 Process Specifications
- 1.2.2 Printer Basic Specifications
- 1.2.3 Paper Specification
- 1.2.4 Reliability, Durability, Serviceability
- 1.2.5 Operating Conditions (Including Consumables)
- 1.2.6 Storage and Transport of the Printer Main Unit and Optional Products (Consumables Packaged)
- 1.2.7 Electrical Features
- 1.2.8 Compliance with Standards and Regulations
- 1.2.9 Consumable Components
- 1.3 External Appearance and Parts Name
- 1.4 Controller Specification
- 1.5 Control Panel (EPL-6200)
- 1.6 Control Panel (EPL-6200L)
- 1.7 RAM Expansion
- 1.8 System Requirements (Only for EPL-6200L)
- 1.9 Paper Feed Specifications (Only for EPL-6200L)
- 1.10 Notes on Operation
- 1.11 Status Sheet
- 1.12 Ambient Conditions
- 1.13 Differences in Specifications between Intended Markets
- 1.14 Notes on Installation of Optional Units
- Operating Principles
- 2.1 Overview
- 2.2 Description of Mechanisms
- 2.3 Operating Principles of Electric Circuitry
- Troubleshooting
- 3.1 Overview
- 3.2 Troubleshooting When There is Error Display
- 3.2.1 Fuser warming up problem
- 3.2.2 Fan problem
- 3.2.3 Polygon Motor Error
- 3.2.4 Laser problem
- 3.2.5 High voltage circuit problem
- 3.2.6 Fuser high temperature problem
- 3.2.7 CPU Error
- 3.2.8 Engine Communication Error
- 3.2.9 Fuser low temperature problem
- 3.2.10 Standard RAM Error
- 3.2.11 RAM Error (Slot 0)
- 3.2.12 ROM Checksum Error (Font)
- 3.2.13 ROM Checksum Error (Program)
- 3.2.14 Option ROM Error
- 3.2.15 EEPROM Error
- 3.2.16 Engine Initialization Error
- 3.2.17 Other Hardware Error
- 3.2.18 Software Error
- 3.3 Troubleshooting for Paper Jam
- 3.4 Troubleshooting for Abnormal Operations
- 3.5 Troubleshooting for Electrical Parts
- 3.6 Troubleshooting for Print Quality Problems
- Disassembly and Assembly
- Adjustment
- Maintenance
- Appendix
EPSON EPL-6200/EPL-6200L Revision A
Troubleshooting Troubleshooting for Paper Jam 118
3.3.3.3 Transport Area Jam in Duplex Unit (Option)
Detection Timing
Solution: Check the “Initial Check Items” (p.116) first and then replace the
following components in the order named with new ones and repeat
checking.
1. Eject Sensor (PS3)
2. Duplex Unit Upper Transport Sensor (PC4)
3.
Main Board Assy (C533/C534 Main) (p.146)
4. Duplex Unit Control Board (p.163)
3.3.3.4 Paper Re-feed Area Jam in Duplex Unit (Option)
Detection Timing
Solution: Check the “Initial Check Items” (p.116) first and then replace the
following components in the order named with new ones and repeat
checking.
1. Eject Sensor (PS3)
2. Paper Feed Sensor (S1)
3. Duplex Unit Lower Transport Sensor (PC5)
4. Duplex Unit Control Board
(p.163)
5. Main Board Assy (C533/C534 Main) (p.146)
Table 3-25. Transport Area Jam in Duplex Unit (Option)
Category Explanation
Transport component
jam
The Duplex Unit Upper Transport Sensor did not turn ON even after
the passage of the predetermined period of time from interception of
the light to the Paper Eject Sensor.
C H E C K
P O I N T
Before replacing any electrical part, check to see if the part in
question is defective or not by consulting “3.5 Troubleshooting for
Electrical Parts”
(p.121). Then replace the part, if necessary.
Table 3-26. Paper Re-feed Area Jam in Duplex Unit (Option)
Category Explanation
Paper pre-feed area
jam
The Paper Feed Sensor did not turn ON even after the passage of the
predetermined period of time from start of paper re-feeding.
The Paper Feed Sensor turned ON before the passage of the
predetermined period of time from start of paper re-feeding.
Remaining paper
detection in paper re-
feed area
The Duplex Unit Upper Transport Sensor of Duplex Unit Lower
Transport Sensor was ON at turning on of the Main Switch, at
opening and closing of the Duplex Unit Cover, at occurrence of a
paper jam or at stop of paper transport.
C H E C K
P O I N T
Before replacing any electrical part, check to see if the part in
question is defective or not by consulting “3.5 Troubleshooting for
Electrical Parts”
(p.121). Then replace the part, if necessary.