Installation and Assembly: ADVANCED PROJECTOR CEILING MOUNT WITH PRECISION GEAR Model: ELPMBPRG, ELPMBPRG-B ENG Compatible with: ELPMBC01 ELPMBP01 ELPMBP02 ELPMBP03 Max UL Load Capacity: 50 lb (22.7 kg) Manufactured by Peerless Industries, Inc. 2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.
NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, call Peerless customer care at 1-800-865-2112.
Before you start check the parts list to ensure all of the parts shown are included. Parts List Description projector mount assembly adapter plate dedicated adapter plate M4 x 20 mm socket pin serrated washer head screw #10-32 x 3/8" socket pin serrated washer head screw 3/8" spacer M4 x 6 mm socket pin serrated washer head screw concrete anchor 10-32 x 1/4" socket pin screw with lock 4 mm security allen wrench washer #14 x 2.
Installation to Extension Column 1 NOTE: Refer to accompanying instructions for ELPMBP01, ELPMBP02, ELPMBP03 or CMJ and ACC Series Ceiling Mounts (sold separately) for installing these models to ceiling. Screw projector mount assembly (A) onto extension column as shown in figure 1.1. Use 4 mm allen wrench (J) to tighten swivel stop screw.
Installation To Wood Joist Ceilings WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that projector mount assembly is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power. • Never tighten in excess of 80 in. • lb (9 N.M.). • Make sure that mounting screws are anchored into the center of the stud.
Installation to Concrete Ceilings WARNING • Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. 1 Place projector mount assembly (A) on ceiling as a template and mark the center of the two mounting holes. Drill two 5/16" (8 mm) dia. holes to a minimum depth of 2.5" (64 mm). Attach projector mount assembly (A) using two concrete anchors (H), two flat washers (K), and two #14 x 2.5" wood screws (L) as shown in Illustration A and 1, 2 and 3).
Installing Plates to Projector CAUTION • All spacers shall be used where indicated. Not using spacers can cause damage to projector. • It is the responsibility of the installer to ensure that the projector is properly ventilated. NOTE: For all PowerLite® models, the manufacturer's product weight must be reviewed to ensure that the weight does not exceed 50 lbs.
2 NOTE: Shoulder indicates back of adapter plate (B) Flip projector upside down. Find your projector model from the hole patterns listed below. Using the holes indicated on the corresponding hole pattern diagram, attach adapter plate (B) to projector using the appropriate number of M4 x 20 mm socket pin serrated washer head screws (D), #10 flat washers (N), and spacers (F). NOTE: Retaining spacers go between adapter plate and projector.
Installing Connection Block to Projector Mount Assembly WARNING • Always use an assistant or mechanical lifting equipment to safely lift and position the projector. 3 Slide connection block with projector into projector mount assembly (A) as shown. Tighten captive screw to secure projector to projector mount assembly (A).
Projector Alignment 5 To adjust yaw (swivel) for extension column installation: Loosen screw on projector mount assembly (A) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn by hand for easy adjustment. To adjust roll (side to side tilt): Turn knob on side of mount as shown below. Pull knob out and turn by hand for easy adjustment.
Cable Management To make an opening to route cables through 6 projector mount assembly, adjust projector mount fig. 6.1 CABLES WITH COMBINATION OF VGA CONNECTOR AND RCA PLUGS assembly to full upward tilt position and maximum left or right roll position by turning knobs for adjustments as shown in step 5. BEND WIRES OF RCA PLUGS IN OPPOSITE DIRECTION Route cables through top of extension column as shown.
