All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of Seiko Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Important Safety Instructions 1. Read all of these instructions and save them for later reference. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this product near water. 5. Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product. 6.
10. If an extension cord is used with this product, make sure that the total of the ampere ratings on the products plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total of all products plugged into the wall outlet does not exceed 15 amperes. 11. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock.
Safety Information Laser Safety This printer is certified as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This means that the printer does not produce hazardous laser radiation.
Operator Safety This Laser Page Printer is considered a CDRH Class I laser device, safe for personal use. The printer contains a 5 milliwatt, 760-810 nanometer wavelength, GaAlAs laser diode. Direct (or indirect reflected) eye contact with the laser beam may cause serious eye damage; however, safety precautions and interlock mechanisms have been designed to prevent any possible laser beam exposure to the operator.
Contents Introduction Chapter 1 Setting Up the Printer Finding a Place for the Printer . . . . . . . . . . . . . . . . . . . . . . . Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Assembling the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1-4 1-7 Chapter 2 Testing and Connecting Your Printer The Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Testing the Printer . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6 Maintenance and Transportation Replacing Consumable Parts . . . . . . . . . . . . . . . . . . . . . . . . Cleaning Your Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transporting Your Printer . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 6-17 6-18 Chapter 7 Troubleshooting Status and Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . Troubleshooting Directory . . . . . . . . . . . . . . . . . . . . . . . . . . Paper Jam Problems . . . . . . . . . .
Appendix B Font Cartridges Available Font Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Font Cartridges. . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 B-4 Appendix C Character Samples and Symbol Sets Available Fonts and Symbol Sets. . . . . . . . . . . . . . . . . . . . . HP Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LQ and FX Emulation Modes . . . . . . . . . . . . . . . . . . . . . . . . Converting Hexadecimal Numbers to Decimals.
X
Introduction Your high-performance Epson laser printer combines reliability and a wide range of features to give you high-quality printing that is both fast and quiet. ® The printer uses a semiconductor laser with the electrophotographic technology used in photocopiers. The imaging system is driven by a powerful processor that allows the printer to compose an entire page in internal memory before printing.
Introduction Two built-in interfaces: A Centronics parallel interface and an RS-232C serial interface. The RS-232C interface allows you to receive data at a baud rate of up to 19200 bps. ® 0.5 megabytes (MB) of RAM built-in, expandable up to 5.5MB, for graphics printing and multiple interface operation. The ability to connect two computers at the same time (or three when an optional interface is installed). Options Many printer options are available for your printer.
Introduction Multi-media feeder (C812141) The optional multi-media feeder allows you to feed various-sized papers into your printer. This tray feeds up to 150 sheets of plain paper or 15 envelopes.
Introduction Memory board (C8226Ol) You can increase your printer’s memory using the memory board and memory chips. You can expand the memory to a total of 5.5MB, enough to print complex graphics. See Appendix A for information on expanding your printer’s memory.
Introduction Epson GL identity card (C826021) The Epson GL identity card allows your printer to emulate an HP 7475A/7440A plotter.
Introduction Laser printer precautions This printer uses laser technology. The following list of precautions applies whenever you open the printer cover. Even if you are familiar with other types of printers, be sure to follow these precautions carefully to ensure safe, efficient operation. l Do not touch the fuser, which is marked by a CAUTION: HOT SURFACE label. If the printer has been in operation, the fuser is very hot. Protect the light-sensitive photoconductor unit from exposure to light.
Introduction Finding your way around This manual provides fully illustrated, step-by-step instructions on setting up and operating your printer. Chapter 1 contains information on unpacking and setting up the printer. Be sure to read and follow these instructions first. Chapters 2 and 3 contain information on using the control panel, testing and connecting the printer, and using your printer with application software.
Introduction Warnings, Cautions, and Notes WARNINGS must be followed carefully to avoid bodily injury. CAUTIONS must be observed to avoid damage to your equipment. Notes contain important information and useful tips on the operation of your printer. Tips for the first-time laser printer user To get you off to a good start with your Epson laser printer, we offer a few tips you may find helpful: Remember to wait for the full page to be composed before it prints and feeds out.
Introduction On rare occasions, a print job needs an extra push. For some print jobs (such as a print screen), the printer may not print even though the data has been sent to the printer’s memory. If the FEED light is on, press ON LINE to take the printer off line and then press the FEED button to print. Adjust your software’s lines-per-page setting to 60. You may have used a lines-per-page setting of 66 with your dot matrix printer.
Introduction Where to get help Epson America provides local customer support and service through a nationwide network of authorized Epson dealers and Service Centers.
Chapter 1 Setting Up the Printer Finding a Place for the Printer. . . . . . . . . . . . . . . . . . . . . . . . 1-2 Unpacking the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Carrying the printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 1-6 Assembling the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the photoconductor unit. . . . . . . . . . . . . . . . . . Installing the toner cartridge . . . . . . . . . . . . . . . . . .
Finding a Place for the Printer Before unpacking the printer, you need to find a suitable place to use it. Follow these guidelines: Place the printer on a flat, stable surface. Place the printer close enough to the computer or workstation for its cable to reach. Use a grounded outlet that has three holes to match the plug on the printer’s power cord. Do not use an adapter plug.
Finding a Place for the Printer CAUTION: Avoid locations that are subject to direct sunlight, excessive heat, moisture, or dust. Avoid using electrical outlets that are controlled by wall switches or automatic timers. Accidental disruption of power can wipe out valuable information in your computer’s and printer’s memory. Avoid using outlets on the same circuit with large motors or other appliances that might affect the power supply.
Unpacking the Printer The printer and the other components are in separate packaging inside the main carton. 1. Carefully unpack the main carton and make sure you have the accessories shown below.
Unpacking the Printer 2. Carefully remove the printer from the large carton and set it on a flat, stable surface. Since the printer is heavy, you may need someone to help you lift it. 3. Remove the plastic protective bag from the printer. Then remove the plastic bags from the paper cassette, output tray, and power cord. Note: Make sure that you save all packing materials. Repack the printer in these materials whenever you ship it. See Chapter 6 for details on transporting your printer.
Unpacking the Printer Carrying the printer When you move your printer to the location you selected, carry it by placing your hands underneath each side of it, as shown below: Note: The printer weighs about 13 kg (29lbs) and should be carried with care. You may need someone to help you lift it.
Assembling the Printer Before you can use the printer, you need to install a few parts. Make sure your printer is in its operating location before you install these parts. Note: The consumable parts for this printer are listed below. It is recommended you keep spares on hand for timely replacement. For more information about the life of these parts, see Consumable parts in Chapter 8.
Assembling the Printer CAUTION: Never touch any part of the photoconductor unit except the green handles. Do not expose the photoconductor unit to light brighter than normal room light. Never install the toner cartridge before you install the photoconductor unit. 1. Push down on the latch on the top of the printer to open the printer cover.
Assembling the Printer 2. Remove the photoconductor unit from its packaging. Pull the red protective pieces from both sides of the unit, as shown below. 3. Hold the photoconductor unit by the green handles and insert it into the printer, as shown below.
Assembling the Printer 4. Pull out the protective black paper from the photoconductor unit. 5. Gently press down on the top of the printer cover until the latch clicks shut. Note: You cannot close the printer cover if the photoconductor unit is not installed correctly. If you cannot close the cover, remove the unit and then re-install it correctly. Then close the printer cover.
Assembling the Printer Installing the toner cartridge After installing the photoconductor unit, you install the toner cartridge. The toner cartridge performs two jobs: providing the toner and developing the image. Note: You cannot install the toner cartridge before you install the photoconductor unit. To ensure even toner distribution, always keep the toner cartridge in a horizontal position during handling. 1. Open the front cover. 2.
Assembling the Printer 3. Remove all the packing tape from the toner cartridge. Then pull the seal tape out of the cartridge firmly in the direction of the arrow. 4. Lift the toner cartridge cover and push it all the way down until it snaps into place. CAUTION: Never touch the roller under the toner cartridge cover; otherwise, print quality may decline. Make sure the toner cartridge cover is open before sliding the cartridge into the printer.
Assembling the Printer 5. Insert the toner cartridge into the printer by sliding it gently into the opening until it locks in place. 6. Close the front cover.
Assembling the Printer Installing the output tray 1. Attach the smaller part of the output tray by fitting the holes on its sides over the two pegs inside the cutout portion of the main tray as shown below. 2. Then attach the assembled output tray by sliding the tray legs into the slots on the back of the printer.
Assembling the Printer Loading and installing the paper cassette 1. Remove all the pieces of packing tape from the paper cassette. Then push down on the metal plate on the bottom of the cassette until it locks in place. 2. Open the paper cassette cover.
Assembling the Printer 3. Take a stack of letter-size paper and fan it. (High-quality copier paper is recommended.) Tap the edges of the paper on a flat surface to even up the stack. 4. Load a stack of up to 100 sheets of paper into the cassette.
Assembling the Printer CAUTION: Make sure the bottom plate of the cassette is in the lowered position; otherwise, a paper jam may occur. Before loading paper, remove the paper cassette from the printer. Otherwise, you may break its cover. Do not load paper above the marks inside the cassette. You can load up to approximately 100 sheets of plain paper in the cassette. Make sure the corner brackets on the cassette cover the edges of the paper. 5. Close the paper cassette cover. 6.
Assembling the Printer Attaching the power cord 1. Before attaching the power cord, make sure the power switch on the printer is turned off. It is off when the O on the switch is pressed down, as shown below. 2. Make sure the rated voltage of the printer matches your outlet voltage by checking the label on the back of your printer.
Assembling the Printer WARNING: If the voltage of the printer and outlet do not match, do not plug in the power cord. Contact your dealer for assistance. 3. Insert the power cord into the socket at the back of the printer, as shown below. Then plug the other end of the cord into a properly grounded outlet.
Chapter 2 Testing and Connecting Your Printer The Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Indicator lights. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 2-2 2-3 2-4 Testing the Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Control Panel The printer control panel is made up of three elements: a liquid crystal display, indicator lights, and buttons. The indicator lights and display let you check the current status of the printer. You use the buttons to select printer settings and functions. Display The display shows the printer’s status and available options. Status messages, such as WARMING UP, indicate the printer’s current status.
The Control Panel Indicator lights CONTINUE Flashes when an error is detected or maintenance must be performed. At the same time, an error or maintenance message appears on the display. FEED On when data is received and stored in the printer but has not yet been printed. Rapid flashing indicates the printer is receiving data from the computer. If the light flashes slowly, the printer is receiving data through an interface other than the default interface in autosense mode.
The Control Panel Buttons SelecType Enters or exits SelecType mode. Press once to enter Level 1; keep holding it down to enter Level 2. For a complete description of the two SelecType levels and their various functions, see Chapter 4. CONTINUE RESET COPY END This button has several functions, so it has three names. This manual uses the name appropriate to the operation being described. CONTINUE-Enables the printer to resume printing automatically after certain error or maintenance-required conditions.
The Control Panel If you continue to hold down this button after RESET appears, INITIALIZE appears on the display and the printer settings return to the settings in effect at power on. See Chapter 4, SelecType. COPY END-Cancels the remaining copies during multi-copy printing. This button is effective only when multiple-copy printing is selected and the printer is off line. FEED MANUAL If the FEED light is lit, press ON LINE to take the printer off line.
Testing the Printer The printer has three built-in print tests: the status sheet and two test prints. These tests let you check the operation of your printer and obtain information on printer settings. Before running a test, make sure you have removed all packing materials from the printer, as described in Chapter 1, and that you have installed all printer parts. You do not need to connect the printer to your computer to run these tests.
Testing the Printer The following messages appear as the printer performs internal tests and warms up. ROM Check RAM Check 0.5MB WARNING READY : P LJ-2P CAUTION: Do not open the printer cover while the printer is warming up or printing. After you turn off the printer, always wait at least five seconds before turning it back on. Never turn the printer off while it is printing or feeding paper. Otherwise a STARTUP error may occur.
Testing the Printer Selecting and printing a status sheet or test print To select and print a status sheet or test print, you must enter SelecType. The printer has two SelecType levels; the status sheet feature is in SelecType Level 1 and the test-print feature is in Level 2. The level selected depends on the amount of time you hold down the SelecType button. Note: For a complete description of SelecType levels and functions, including Level 2 test prints, see Chapter 4.
Testing the Printer 3. Press until STATUS SHEET appears on the display. 4. Press D twice to print the status sheet. A sample printout is shown below. STATUS SHEET EPSON Printer Configuration Installed Memory CH Mode Auto Continue Standby : : : : 3.OMbytes AUTO-SENSE OFF DISABLE CH : P Mode : LJ-2P Controller Version : 15.04 CH Time out : 28 Total Printed Count: 25 Version : 17.
Testing the Printer If the status sheet prints correctly, you can skip to Connecting the Printer to Your Computer found later in this chapter. Adjusting print density If your status sheet is too light or too dark, use the print density control knob inside the printer to make the printing darker or lighter. 1. Push down the latch on the top of the printer to open the printer cover. Locate the small green knob on the inside right middle of the printer as shown below.
Testing the Printer 2. For darker print, turn the knob clockwise. A A 3. For lighter print, turn the knob counterclockwise. A A Note: Cl Increasing the print density increases toner consumption. If you select darker print, you may need to replace the toner cartridge more often. Cl When you replace the toner cartridge, turn the knob to the default position. The knob clicks when you reach the default position.
Testing the Printer 4. Close the printer cover. 5. Print a status sheet again to check the new print density setting.
Connecting the Printer to Your Computer For the printer to receive and interpret information from your computer, both devices must be set up to communicate properly. You must choose the correct interface cable and communication settings. Note: After connecting the printer to your computer and before using your application software, be sure to complete Testing the computer-to-printer connection found at the end of this chapter.
Connecting the Printer to Your Computer Connecting the printer to more than one computer You can connect up to three computers to your printer at the same time; simply connect the interface cables to any of the built-in or optional interfaces. Choosing an interface To connect the printer to your computer, first determine whether you require a parallel or serial connection.
Connecting the Printer to Your Computer 2. Plug the parallel cable connector securely into the parallel interface of the printer as shown below. 3. Squeeze the wire clips together until they lock in place on either side of the connector.
Connecting the Printer to Your Computer 4. If your cable has a grounding wire, connect it to the printer’s ground connector as shown. 5. Plug the other end of the parallel cable into your computer and fasten the connector screws to the interface, if necessary. Some parallel cables have grounding wires at the computer end as well. If so, connect this wire to the ground screw on the computer. Note: You can use the SelecType Level 2 I/F CONFIG option to change some of the parallel interface settings.
Connecting the Printer to Your Computer Testing the parallel connection To make sure you properly connected your computer to your printer, follow these steps before you begin working with your application software: 1. Turn on your computer; then turn on your printer. 2. Bring up a DOS prompt on your computer screen such as: c:> If you do not have a C drive, A:> or B:> may appear. 3. Type DIR and press Enter. The screen shows a directory listing of the files in the designated drive. 4.
Connecting the Printer to Your Computer 6. If nothing prints or the results are not what you expect, review the section on Connecting the Printer to Your Computer found earlier in this chapter. Make sure that you used the proper cable, that the cable is connected securely to both the computer and the printer, and that you selected the appropriate interface. 7. If you are still not able to print the computer screen, see Where to Get Help in the introduction of this manual.
Connecting the Printer to Your Computer 3. Use a screwdriver to fasten the screws of the connector, if required. 4. If your cable has a grounding wire, connect it to the printer’s ground connector. 5. Plug the other end of the serial cable into your computer. (Fasten the connector screws to the interface, if required.) You may need to change some interface settings, such as baud rate and parity, before your printer and computer can communicate properly.
Chapter 3 Using your Printer with Application Software Using Printer Selection Menus . . . . . . . . . . . . . . . . . . . . . . . Matching the printer mode to your application program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printing a test file. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Printer Selection Menus Once you’ve set up the printer, you can start using it with your application software program by choosing a printer name from the program’s printer selection menu. If your program has a printer selection menu, follow the instructions below about printer emulation (operating) modes to get the best performance from your printer. Matching the printer mode to your application program Your printer has three printer operating modes, also called emulations.
Using Printer Selection Menus Epson LQ and FX emulation modes If your software supports only Epson LQ or FX printers, select the appropriate emulation mode using SelecType. To choose LQ mode, follow the steps below. (To choose FX mode, at step 4, simply choose FX instead of LJ-2P or LQ.) 1. Press and hold down the SelecType button until SelecType LEVEL2 appears on the display. 2. Press 3. Press until MODE ASSIGN appears. The following appears on the display.
Using Printer Selection Menus 6. Press three times to exit SelecType. Note: The printer mode you have selected remains in effect only until you turn off the printer unless you store the current printer mode settings by performing the P-CONFIG SAVE function described in Saving the paper-size setting in Chapter 5. 7. Enter your program’s printer selection menu and choose the first printer available from the list of printers below. (They are listed in order of preference.
Using Printer Selection Menus Printing a test file After you set the printer mode and select the most appropriate printer from your program’s printer selection menu as described above, create and print a test file using the fonts, symbols, features, and formats that you use most often. Printing the test file shows you how the printer works with your application program. If the printing results are not what you expect, see Chapter 7, Troubleshooting, or consult your computer or software manual.
Chapter 4 SelecType SelecType Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SelecType Level 1 functions. . . . . . . . . . . . . . . . . . . . . . . . SelecType Level 2 functions. . . . . . . . . . . . . . . . . . . . . . . . 4-2 4-3 4-4 Using SelecType. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thedisplay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SelecType Overview The SelecType function on the printer control panel allows you to print test pages, display memory size, select paper sizes, and change your printer’s configuration without using DIP switches or software commands. However, use SelecType only when you are unable to use your application software to control settings required for your print job.
SelecType Overview SelecType Level 1 functions Selects the standard cassette or the optional INPUT multi-media feeder or both. P-SIZE Specifies the size of paper. COPIES Selects the number of copies to be printed. ORIENT Orientation. Selects portrait (vertical) or landscape (horizontal) printing orientation. FONT Selects one of the available fonts. STATUS SHEET Prints a report listing the current printer settings. FONT SAMPLE Prints all font samples (bit-map and scalable fonts) in the printer.
SelecType Overview SelecType Level 2 functions TEST PRINT Prints two test patterns. MODE ASSIGN Chooses one of the emulation modes: HP LaserJet III’, Epson LQ, Epson FX, or (with the optional identity card installed) Epson GL. I/F CONFIG Configures the parallel and serial interfaces. RX-BUFFER SIZE Chooses the size of the receive buffer, CH Channel mode. Sets the interface channels to auto-sense or individual. CH TIMEOUT Channel time out.
Using SelecType This section describes the control panel and explains how to use SelecType. If you would like to try a sample exercise, see Steps to using SelecType later in this section. The Control Panel The control panel contains the SelecType button (which also functions as the left arrow button, three indicator lights, four arrow buttons, and the display.
Using SelecType The Display When you enter SelecType, menus and options appear on the display. The display shows SelecType main menus on the left side and options for each menu on the right side. The display also uses the icons shown below: This icon to the left of an option indicates that you can press either or to view other options in the menu. This icon to the left of an option indicates that the option displayed is the current selection. You can use or to view other options.
Using SelecType Steps to using SelecType There are five basic steps to using SelecType: 1. Enter SelecType mode. 2. Move to the option you want. 3. Set, select, or execute the option. 4. Save the new setting, if necessary. 5. Exit SelecType mode. You’ll see how to complete each step on the following pages. This section uses the SelecType Level 1 INPUT option to explain the steps to using SelecType. You may want to try each step as you read it for hands-on practice.
Using SelecType Press below. until the INPUT option appears on the display, as shown The display shows one of the choices in the INPUT option to the right. Most options have further levels, called submenus, or a list of choices connected to the option. Some options, like the SUB CONFIG option, may display only the main option until you enter the submenu. And some options, like the VERSION option, simply display information about your printer.
Using SelecType The icon to the left of AUTO indicates that the option is not selected and >SET indicates that you can set that option by pressing . Note: Although the main menu options are the same for all operating modes (LQ, FX, and LJ-2P), some Level 1 submenu options are different in each mode. Submenu options for each mode are discussed later in this chapter. Set, select, or execute the option To set, select, or execute an option, you simply press D Press D to select AUTO.
Using SelecType Exit SelecType mode To exit SelecType mode from any option, press until the following display appears: 4-10 SelecType one or more times
SelecType Options This section lists all the options available when you use SelecType. Most options are the same whether you’re working in LJ-2P, LQ, or FX emulation mode. Some of the options in Level 1, however, have a different function for each mode. These options are listed later in this chapter. See the Quick Reference card at the back of this manual for a map of all SelecType menus and options.
SelecType Options INPUT STD * STD OPT AUTO This option selects whether paper feeds into the printer from the standard paper cassette or the optional multi-media feeder. If you choose STD, the printer loads paper from the standard paper cassette. If you choose OPT, the printer loads paper from the optional multimedia feeder. OPT appears as an option on the display only if the optional multi-media feeder is installed.
SelecType Options P-SIZE A4 A5 B5 *LETTER HALF LT LEGAL GLT GLG EXE F4 MONARCH Cl0 DL C5 LETTER (Half Letter) (Government Letter) (Government Legal) (Executive) (Commercial 10) You can probably choose the paper size with your application software, but if necessary, you can choose any of the paper sizes shown above with the P-SIZE option. The factory setting is LETTER.
SelecType Options ORIENT. PORT * PORT LAND The orientation option selects the direction in which the characters are printed on a page. You can choose portrait (vertical) or landscape (horizontal) orientation. FONT RD- 0 Available options in the FONT submenu are different for each printer mode. See Choosing a Font later in this chapter for information on using this option.
SelecType Options STATUS SHEET Use this option to print a status sheet that lists the current printer settings. When you reach this option, press D twice to print the status sheet. See Selecting and printing a status sheet in Chapter 2. EPSON STATUS SHEET Printer Configuration Installed Memory CH Mode Auto Continue Standby : : : : 3.OMbytes AUTO-SENSE OFF DISABLE CH : P Mode : LJ-2P Controller Version : 15.
SelecType Options SUB CONFIG. The submenus for the subconfiguration option are different in each printer mode. See Using the SUB CONFIG Option later in this chapter for information on using this option. SYSTEM CONFIG. This option includes these eight submenus: FULL PRINT T-OFFSET 1-OFFSET MEMORY LEFT LOAD MACRO SAVE MACRO DELETE MACRO POWERON MACRO Each submenu is explained below.
SelecType Options Paper Size Setting Paper Size Setting A4 51 GLG 57 A5 35 GLT 45 B5 43 F4 57 LT 47 MONARCH 31 LG 62 Cl0 41 HLT 36 DL 37 EXE 45 C5 38 I I Since the amount of RAM you reserve with this option is not available for any other purpose, it is best to leave the setting at 0 until you see a SET FULL PRINT message. Then, increase the setting in small increments until the error does not occur.
SelecType Options L-OFFSET 0 -64 to +63 Use the L-OFFSET (left offset) option to make fine adjustments in the position of the printing on the page. The setting is in dots; each dot is 1/300th of an inch (0.0846 mm). With this option, you can move the printing on the page approximately 1/5th of an inch (5 mm) to the left (settings from -1 to -64) or to the right (settings from 1 to +63). The factory setting is 0. K MEMORY LEFT This option displays the amount of memory (in kilobytes) available.
SelecType Options SAVE MACRO 1 1to 4 This option lets you save your current Level 1 settings as a macro , the display shows: and recall them anytime. When you press Select a macro number for your setting by pressing or Then press to save the current SelecType Level 1 settings into the macro. Next use the POWERON MACRO option described later in this section to choose the same number as chosen in SAVE MACRO. Then the settings you have chosen are in effect each time you turn the printer on.
SelecType Options DELETE MACRO 1 This option lets you delete any macros you create. When you press , the displays shows the following: Move to the number of the macro you want to delete by pressing or . Then press to delete the macro. All the settings saved with the specified macro are deleted. Press to return to the main menu without deleting a macro. POWERON MACRO 0 0 to 4 Use this option to specify the macro number you want to use as the power-on default for each operating mode.
SelecType Options Level 2 options When you press and hold down the SelecType button for a few seconds (until the SelecType LEVEL2 message appears on the display) to enter Level 2, one of the main menu options listed below appears on the display: TEST PRINT MODE ASSIGN I/F CONFIG RX-BUFFER SIZE CH CH TIMEOUT AUTO CONT P-CONFIG SAVE FACTORY RESET VERSION PAGE COUNTER STANDBY Each of these options is described below. An asterisk (*) indicates the factory default setting, if there is one.
SelecType Options MODE ASSIGN This option allows you to choose one of the three operating (or emulation) modes. * LJ-2P LQ FX The HP emulation mode offers the widest range of features, but you may also want to select the other modes to use software written specifically for other printers. You must change the MODE ASSIGN setting before you can operate your printer as an Epson LQ or FX printer. Press .
SelecType Options I/F CONFIG The interface configuration option allows you to change the settings for either of the built-in interfaces, the parallel or the serial. First press to move to the channel selection submenu. Press to change the channel, if necessary; then press . The PARALLEL option has these three submenus: SLCTIN AUTOFEED BUSY DELAY SLCTIN OFF ON * OFF With SLCTIN set to off, the printer is continuously selected and device control codes DC1 and DC3 are ignored.
SelecType Options AUTOFEED OFF ON * OFF When this option is set to off, the AUTOFEED signal on pin 14 is ignored and the printer does not send an automatic line feed (LF) command with each carriage return (CR). When AUTOFEED is set to on, a line feed is added to each carriage return the printer receives. If your text lines overprint each other, you may need to set AUTOFEED to on. BUSY DELAY 0 -5 *0 +5 MIN This option sets the delay period from the ACKNLG to the BUSY signal.
SelecType Options If you are using the serial interface, see your computer manual for the proper settings. The printer settings must match the computer settings. WORD LENGTH 8 7 *8 You can select a word length for serial communications from two options: 8-bit word length or 7-bit word length. See your computer manual and software documentation for the proper setting. The factory setting is 8-bit.
SelecType Options NONE PARITY *NONE ODD EVEN When this option is set to NONE, parity checking is disabled. The parity bit, if used, provides a basic form of error detection. See your computer manual and software documentation for the proper setting. STOP BIT 2 1 *2 This option sets the number of stop bits on each character of information sent to the printer. Stop bits signal the end of a character. DTR ON *ON OFF This option turns the printer ready communications protocol on or off.
SelecType Options XON/XOFF ON *ON OFF This option turns the XON/XOFF communications protocol on or off. XON/XOFF protocol can be used in combination with the DTR option setting. ENQ/ACK OFF ON “OFF This option is available in the Epson GL mode only. DSR OFF ON *OFF When DSR (Data Set Ready) is off, the signal level is permanently set HIGH, allowing the printer to send data to the computer. For most communications purposes, this option should be set to off (signal level HIGH).
SelecType Options OFF CTS ON *OFF When CTS (Clear To Send) is off, the signal level is permanently set HIGH. The factory setting is off (signal level is HIGH). This setting should be set to off for most communications purposes. When CTS is on, data is sent to the computer only when CTS is HIGH. RX-BUFFER SIZE 1 to 99 (K) The receive buffer size option allows you to change the size of the printer’s input buffer.
SelecType Options CH AUTO-SENSE This option specifies how the printer’s memory is allocated among the channels. There are two basic settings: AUTO-SENSE and INDIVIDUAL. With AUTO-SENSE the printer automatically detects which interface channel (parallel, serial, or optional) is being used. This is the default setting and is the best choice for most uses of the printer. The INDIVIDUAL setting requires you to add memory to the printer and allows you to allocate independent memory to each channel.
SelecType Options If you choose INDIVIDUAL, you see this display: CAUTION: Do not use the INDIVIDUAL setting unless you have installed additional memory as described in Appendix A. If you save this option before adding memory, you could damage your printer. Press to move to the following display: The number on the left is the total number of megabytes (M) available, and the number to the right of each channel is the proportion of the memory allocated to that channel.
SelecType Options Press to execute the save and initialize operation. Your settings are now saved and also are in effect every time you turn the printer on. CH TIMEOUT 60 10 to 600 (in steps of 10) This option sets the time for a channel timeout. If the printer is on line and no new data is sent for the number of seconds specified, and there is data in the other channel, the printer automatically switches from the current channel to the other. The factory setting is 60. AUTO CONT.
SelecType Options Press ; the display shows the following: Press to initialize the printer or press the main menu without saving. to cancel and return to FACTORY RESET FACTORY RESET returns all Level 1 and Level 2 settings to their factory settings. When-you select the FACTORY RESET option, the display shows the following: Press to execute the reset, or press without resetting the printer.
SelecType Options VERSION This option displays the version number of the printer’s controller and font. Press to see the C-ROM version number, and then press to see the FONT version number. PAGE COUNTER ## This option displays the number of sheets printed since the printer was installed. Press to display the following: This option displays the number of sheets printed for the current photoconductor unit.
Choosing a Font The FONT option is different for each printer mode. This section describes the available submenus of the FONT option in each mode. You can use the level 1 FONT SAMPLE option as described earlier to print out a list of the available fonts. Note: You will almost always use your application software, not SelecType to select fonts. HP emulation mode When you are in the LJ-2P mode, the FONT option display shows: FONT Press RD- 0 to enter the FONT option. You first choose the font source.
Choosing a Font After you choose the font source, you choose the font by number based on the font source option selected above. Only fonts that match the current orientation setting can be selected. If you change the SYMSET or ORIENT settings, the available font numbers may change. To save a selected font as the default font, use the SAVE MACRO option in the Level 1 SYSTEM CONFIG menu.
Using the SUB CONFIG Option The subconfiguration option is different for each printer mode. The function and submenus of the SUB CONFIG option for each mode is described below. Once you set new settings with the SUB CONFIG option, each setting remains in effect until you change it again or turn off the printer unless you use the Level 1 SYSTEM CONFIG option SAVE MACRO setting described earlier in this chapter.
Using the SUB CONFlG Option If *** appears on the display, the number of lines you set is out of the possible range of 0 to 128. SYMSET Roman-8 Use the SYMSET option to choose from 26 resident HP symbol sets. (The HP LaserJet series IIP printer has 25 symbol sets.) In most cases, you will never need to change this setting.
Using the SUB CONFIG Option LQ and FX emulation modes When you set up your printer to operate in LQ or FX mode, the SUB CONFIG option includes the fourteen submenus shown below: SUB CONFIG. PITCH CONDENSED L-MARGIN R-MARGIN FORM TOP TEXT SKIPBOTTOM CGTABLE COUNTRY J-REPRINT AUTO CR ZERO CHAR. WIDE PAGE B-IMAGE Press D to enter the SUB CONFIG option. PITCH 10CPI "10 12 15 PROP. You can select a character pitch of 10,12, or 15 characters per inch (cpi), or choose proportional spacing.
Using the SUB CONFIG Option CONDENSED OFF * OFF ON You can use this option to change the character spacing. Condensed printing is useful for spreadsheets and other applications where you need to fit the maximum amount of information on each line. The 15 cpi character pitch cannot be condensed. L-MARGIN 0 0 to available This option allows you to set the left margin position. Margin units are determined by the current pitch (characters per inch) and the condensed setting (on or off).
Using the SUB CONFIG Option Default right margin Portrait Paper Size Condensed 1Ocpi 12cpi 15cpi Landscape 1Ocpi 12cpi 15cpi A4 OFF ON 77 133 93 155 116 116 111 191 134 223 167 167 A4(80 col) OFF ON 80 137 96 160 120 120 111 191 134 223 167 167 A5 OFF ON 53 91 63 106 79 79 77 133 93 155 116 116 B5 OFF 66 0 100 9 6 115 144 O N 114 133 100 164 192 144 OFF 8 0 120 105 126 157 O N 137 9 6 160 120 180 210 157 OFF 80 9 6 120 1 3 5 162 202 160 120 2
Using the SUB CONFIG Option 0.50 FORM TOP 0.50-1.50 (inch) This option specifies the distance from the top of the sheet to the baseline of the first printable line. This is measured in 0.05-inch increments. The factory setting is 0.50 inches. TEXT 66LINES 1 to available Use this option to set the page length. The unit of measure for this option is 1/6th of an inch.
Using the SUB CONFIG Option CGTABLE PcUSA * PcUSA PcMulti PcPort PcCanF PcNord DLoad ITALIC The CGTABLE (character generator table) option allows you to select the graphics character table, the italics character table, or the download table. The graphics table contains graphics characters for printing lines, corners, and shaded areas; international characters; Greek characters; and mathematical symbols. Selecting the italics table defines the upper half of the character table as italic characters.
Using the SUB CONFIG Option J-REPRINT ON OFF *ON Use this option to reprint after a paper jam. When it is set to on and a page jams in the printer, the page is reprinted after the jam is cleared. If this option is set to off, a jammed page does not reprint automatically, but complex pages may print faster. AUTOCR ON OFF *ON When AUTO CR (automatic carriage return) is on, the printer performs a carriage-return line-feed (CR-LF) operation whenever the print position exceeds the right margain.
Using the SUB CONFIG Option WIDE PAGE ON OFF *ON When this option is on, you can print up to 80 characters at 10 cpi across an A4 or F4-size page. When it is off, you can print up to 77 characters at 10 cpi. This setting is only valid when P-SIZE is set to A4 or F4. If you change the WIDE PAGE setting when sizes other than A4 or F4 are selected with the P-SIZE option, L-MARGIN automatically defaults to 0 and R-MARGIN and TEXT LINES return to the default settings for the currently-selected paper size.
Chapter 5 Paper Handling Choosing Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Paper-feed Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Special Setting for Thin Paper . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Loading Paper in the Cassette. . . . . . . . . . . . . . . . . . . . . . . . 5-7 Choosing a Paper Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Changing the paper-size setting . . . . . . . . . . .
Choosing Paper With this printer you can print on many sizes and types of paper. You can also use other types of media such as envelopes, labels, and overhead projector transparencies. This chapter describes the paper delivery choices and how to select and load paper. The type of paper you use in your printer directly affects the quality of your printed output. The printed image is made up of many tiny dots of toner that are transferred to the paper.
Choosing Paper Standard office paper-You can use the printer’s paper cassette to 2 feed most types of 16 to 24-1b (60- to 90-g/m ) paper. This typically includes such paper as copier paper, cotton bond, and letterhead. If you feed paper manually one sheet at a time through the manual 2 feed slot, you can use up to 42-1b (157-g/m ) paper. For best results, use paper made especially for laser printers. Paper made for plain-paper copiers is also a good choice.
Choosing Paper Envelopes-Load envelopes face down as shown below. The printing quality on envelopes may be irregular because different parts of an envelope have different thicknesses. If printing is too light, turn the print density knob clockwise. Always return the print density knob to the center (default) position when you go back to printing on ordinary paper.
Paper-feed Method The printer feeds letter-size paper automatically from the standard paper cassette and most types of media from the manual feed slot. A multi-media feeder and a legal-size paper cassette are available options. For information on the multi-media feeder, see Appendix A. The following table lists recommended paper-feed methods for different print media. (If you want to try other methods, be sure to test-print a few sheets before beginning regular use.
Special Setting for Thin Paper If thin paper creases when you print, you can solve the problem by using the control panel to select the Special paper type setting. To change the paper type setting to Special, first make sure the printer is on line. Then press the MANUAL button and hold it down for several seconds. SP appears on the display to show that the printer is in the Special mode. To return to the normal setting, repeat the steps described above. (SP disappears from the display.
Loading Paper in the Cassette The standard paper cassette holds up to 100 sheets of paper. 1. Pull out the paper cassette. CAUTION: Do not open the paper cassette cover while the paper cassette is installed in the printer; this could break the cover.
Loading Paper in the Cassette 2. Push down on the metal plate on the bottom of the cassette until it locks in place. 3. Open the paper cassette cover.
Loading Paper in the Cassette 4. Take a stack of letter-size paper, fan it, and tap the edges on a flat surface to even up the stack, as shown. 5. Insert the stack of paper face down into the paper cassette, making sure that the edges of the paper are covered by both comer brackets on the cassette. Also, make sure that the top of the stack is below the maximum height mark inside the paper cassette.
Loading Paper in the Cassette 6. Close the paper cassette cover. 7. Insert the cassette along the slots on the inside of the printer until it locks in place. 8. If you are using the optional legal-size paper cassette, raise the smaller part of the output tray as shown below.
Choosing a Paper Size The factory paper-size setting is set to letter. Whenever possible, use your application software settings to choose the paper size you require for your print job. If you cannot select the paper size with your application program, you can use the SelecType Level 1 P-SIZE option.
Choosing a Paper Size Changing the paper-size setting 1. Press the SelecType button until the message SelecType LEVEL1 appears. 2. Press 3. Press or until P-SIZE appears. or until the paper size you wish to print on appears. . 4. Press 5. Press to set the new paper size. 6. To exit SelecType, press the SelecType button.
Choosing a Paper Size 8. Press until POWERON MACRO appears on the display. 9. Press to select POWERON MACRO. 10. Press or until you see the macro number you want to take effect each time you turn on the printer. Be sure to use the same number you chose in step 6. 11. Press to execute the saving action. 12. Press the SelecType button to exit SelecType.
Loading Paper Manually If you want to print on paper other than letter-size, or special paper or other media such as labels, envelopes, transparencies, or heavy 2 paper (over 24 lb, or 90 g/m ), you can load the paper one sheet at a time through the manual feed slot. Hand-feeding is convenient when you want to print a small job on paper different from the type already loaded in the cassette. Note: You can also use the manual feed method when the multimedia feeder is installed.
Loading Paper Manually 5. Adjust the paper guides to match the size of paper you are using as shown below. 6. Insert a sheet of paper into the manual feed slot as far as it will go.
Loading Paper Manually Note: When you hand-feed consecutive pages, insert the next sheet after the following messages: These two messages appear alternately. If you press the printer stops manual feeding and feeds paper automatically from the paper cassette or optional multi-media feeder, according to the INPUT menu setting in SelecType Level 1. 7. To return to automatic feeding, press FEED again when the FEED light goes off. Also, the printer must be on line.
Chapter 6 Maintenance and Transportation Replacing Consumable Parts . . . . . . . . . . . . . . . . . . . . . . . . . Replacing the toner cartridge . . . . . . . . . . . . . . . . . . . . . . Replacing the ozone filter. . . . . . . . . . . . . . . . . . . . . . . . . . Cleaning the transfer charger wire. . . . . . . . . . . . . . . . . . Replacing the photoconductor unit . . . . . . . . . . . . . . . . . 6-2 6-3 6-8 6-9 6-10 Cleaning Your Printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing Consumable Parts Your printer’s consumable parts and their approximate usage are shown below: Toner cartridge Up to 5,000 pages depending upon the complexity of print jobs Photoconductor unit Up to 30,000 pages when using lettersize paper Note: See Chapter 8, Consumable Parts for more details about conditions governing consumable part life. The following are consumable part replacement messages: TONER LOW Little toner is left; you must replace the toner cartridge soon.
Replacing Consumable Parts Note: Because other factors such as the paper you print on affect the life of the photoconductor unit, you may occasionally have to replace the unit before you see the CHANGE PCU message. See Troubleshooting, Chapter 7. Replacing the toner cartridge Follow these instructions carefully when you see the TONER OUT message. CAUTION: Do not remove or insert the toner cartridge if the photoconductor unit is not in place. Otherwise, you may damage the printer.
Replacing Consumable Parts 2. Grasp the paper cassette tray with both hands and pull it out of the printer. 3. Open the front cover.
Replacing Consumable Parts 4. Remove the toner cartridge by pulling it straight out. Then close the toner cartridge cover. 5. Dispose. of the toner cartridge as a unit with nonburnable items. Do not take the cartridge apart. Follow any local regulations that may apply to nonburnable waste. 6. While holding the new cartridge in a horizontal position, gently shake the cartridge from side to side a few times to distribute the toner evenly.
Replacing Consumable Parts 7. Remove all packing tape from the cartridge. Then pull the seal tape out of the toner cartridge in the direction of the arrow. 8. Lift back the toner cartridge cover as shown. Then press the cover all the way down until it snaps into place.
Replacing Consumable Parts 9. Insert the toner cartridge into the printer by sliding it gently into the opening until it locks in place. 10. Close the front cover. 11. Insert the paper cassette. Each time you replace the toner cartridge, you should replace the ozone filter and clean the transfer charger wire as described next.
Replacing Consumable Parts Replacing the ozone filter Ozone is generated inside the printer by the high voltages used during the printing process. Replace the ozone filter each time you replace the toner cartridge. 1. Make sure the printer is turned off. 2. Open the fan cover located on the left side of the printer. 3. Pull the filter out of the printer.
Replacing Consumable Parts 4. Install the new filter as shown below. 5. Close the fan cover. Cleaning the transfer charger wire Clean the transfer charger wire each time you replace the toner cartridge. You should also clean the transfer charger wire if the print quality declines. See Chapter 7 for a discussion of the print quality problems that can be solved by cleaning the transfer charger wire. 1. Open the printer cover.
Replacing Consumable Parts 2. Locate the green transfer charger wire cleaner on the photoconductor unit and slide it to the right as far as it will go. Then move it back to its original position. 3. Close the printer cover. Replacing the photoconductor unit When you see CHANGE PCU on the display, it is time to replace the photoconductor unit. To finish printing your current job, press CONTINUE.
Replacing Consumable Parts 1. Make sure the printer is off. 2. Grasp the paper cassette tray with both hands and pull it out of the printer. WARNING: l Do not touch the fuser, which is marked with a CAUTION: HOT SURFACE label. The fuser is very hot during and directly following printer use. Always remove the toner cartridge before removing the photoconductor unit. Removing the photoconductor unit by force will damage the printer.
Replacing Consumable Parts 3. Open the front cover. 4. Pull out the toner cartridge. 5. Push down on the latch on the top of the printer to open the printer cover.
Replacing Consumable Parts 6. Remove the photoconductor unit by pulling up on the green handles on both sides of the photoconductor unit. 7. Dispose of the photoconductor unit by placing it with nonburnable items. Do not take the photoconductor unit apart. Follow all local regulations that may apply to nonburnable waste. 8. Remove the new photoconductor unit from its packaging. Save the packaging in case you ever need to transport the printer. Pull the red plastic pieces from both sides of the new unit.
Replacing Consumable Parts CAUTION: Never touch any part of the photoconductor unit except the green handles. Do not expose the photoconductor unit to light brighter than normal room light. 9. Insert the photoconductor unit into the printer while holding the green handles. 10. Remove the black protective paper from the photoconductor unit.
Replacing Consumable Parts 11. Press and at the same time. Make sure COVER OPEN PCU 0 appears on the display. 12. Gently press down on the top of the printer cover until the latch clicks shut. Note: You cannot close the printer cover if you installed the photoconductor unit incorrectly. If you cannot close the cover, carefully remove and then re-install the photoconductor unit. Close the cover. 13. Re-insert the toner cartridge into the printer by sliding it gently into the opening until it locks in place.
Replacing Consumable Parts 14. Close the front cover. 15. Insert the paper cassette.
Cleaning Your Printer The printer needs only minimal cleaning. If printing problems occur (print is too light, white stripes appear, or nothing prints), see Chapter 7, Troubleshooting. This section describes cleaning the printer case. Cleaning the printer case If the printer’s outer case is dirty or dusty, first turn off the printer; then clean it with a soft, clean cloth dampened with a mild detergent, as shown below.
Transporting Your Printer If you need to move the printer a short distance, such as from one room to another, remove the paper cassette and make sure that you keep the printer level to avoid spilling toner. If you plan to ship the printer some distance, repack the printer and its accessories in the original packing materials to avoid damaging them.
Transporting Your Printer 3. Remove the output tray and the paper cassette. Then remove any paper in the paper cassette and repack the cassette in its original packing materials. 4. Open the front cover. 5. Pull out the toner cartridge. 6. Make sure the toner cartridge cover is closed. Then put the toner cartridge back in its original plastic bag.
Transporting Your Printer 7. Close the front cover. 8. Push down on the latch on the top of the printer to open the printer cover. 9. Remove the photoconductor unit by pulling up on the green handles located on both sides of the unit as shown below.
Transporting Your Printer CAUTION: Never touch any part of the photoconductor unit except the green handles. Do not expose the photoconductor unit to light brighter than normal room light. 10. Put the photoconductor unit back in its original packaging. 11. Close the printer cover. 12. Place the toner cartridge in its original box, securing it so that it cannot move around inside the box, and seal the box with packing tape.
Chapter 7 Troubleshooting Status and Error Messages. . . . . . . . . . . . . . . . . . . . . . . . . . . The messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 7-2 Troubleshooting Directory. . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8 Paper Jam Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FEED JAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAPER JAM . . . . . . . . . . . . . . . . . . . . . . . .
Status and Error Messages If an error occurs, your best source of information is the display on the control panel. The messages displayed there tell you what may be wrong and, in some cases, indicate the actions you should take to correct the problem. Status messages appear on the display during normal operation. They indicate the printer’s current status.
Status and Error Messages [E] CHANGE PCU Replace the photoconductor unit as described in Chapter 6. [S] CHAR CREATING Characters are being created. [S] COPY END Multiple-copy printing is cancelled. (You pressed the COPY END button when the printer was off line.) [E] COVER OPEN PCU XXXXXX The printer cover or fan cover is open or the toner cartridge or photoconductor unit is not installed. The number following PCU shows the number of pages printed.
Status and Error Messages [E] ILLEGAL CARD A card in the card slot or a cartridge in the cartridge slot cannot be read. To correct this error, take the printer off line and then press CONTINUE. If the error message remains, make sure the printer is off line and remove the card or the cartridge. [S] INITIALIZE The printer is being initialized to the factory or optional settings. [E] INSUFF MEMORY The printer has insufficient memory available for the task you have given it.
Status and Error Messages [E] PAPER OUT [paper source] [paper size] There is no paper in the paper source from which the printer expects to feed paper. The right column of the display prompts you to load the correct paper size into the paper source. [E] PAPER SIZE ERROR The paper size you selected with SelecType (or the default size if you have not selected a size) does not match the paper loaded in the selected paper source. Press CONTINUE to clear the error.
Status and Error Messages [E] RESELECT TRAY The optional multi-media feeder is not installed and the INPUT option is set to OPT or AUTO. Install the optional multi-media feeder and then press CONTINUE. However, if you decide not to use the optional multi-media feeder, simply press CONTINUE and paper is automatically selected from the standard paper cassette.
Status and Error Messages [E] SET FULL PRINT This message may appear when you are trying to print graphics or a mix of text and graphics. Press CONTINUE and then change the FULL PRINT setting in SelecType Level 1. See Chapter 4 for more information about this setting. [S] STANDBY MODE If the standby mode is enabled, the printer enters this mode when it is not used for about thirty minutes. Even if the standby mode is disabled, the printer enters standby mode when it is not used for eight hours.
Troubleshooting Directory Use the directory below to help you locate the printing problem you are experiencing; then work through the suggested solutions. If the exact problem is not listed, look for one of a similar type. Most printing problems can be corrected easily. Paper jam problems Feed jam. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper jam.......................................... 7-10 7-12 Power supply Power is not being supplied to the printer. . . .
Troubleshooting Directory Decline in print quality The print quality is not what you expected. . . . . . . . . . . . . 7-29 Options Using optional font cartridges, the printer does not operate as expected. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-34 Using the optional multi-media feeder, the printer does not operate properly. . . . , . . . . . . . . . . . . . . . . . . . . . . . 7-34 Using an optional interface, the printer does not operate as expected.. . . . . . . . . . . . . . .
Paper Jam Problems This section gives you detailed information on correcting paper jams. Find the error message on your display and work through the steps below to correct the problem. FEED JAM The FEED JAM message indicates that paper is not feeding into the printer from the specified tray or has jammed on its way into the printer. When a feed error occurs, the printer stops printing. When you see the FEED JAM message, follow these steps: 1. Remove the paper cassette from the printer.
Paper Jam Problems CAUTION: If the paper tears while you remove it, make sure you also remove any pieces remaining in the printer. To do this, open the printer cover, remove any paper pieces from the paper feed path, and close the printer cover. 2. Open and close the printer cover to reset the paper jam detector. 3. Tap the edges of the paper on a flat surface and reload it into the paper cassette. (Do not reload any curled or wrinkled sheets.) 4. Push the paper cassette back into the printer.
Paper Jam Problems 3. Make sure that the paper is evenly aligned in the multi-media feeder and that the paper rests below the multi-media feeder’s maximum paper marks. Then replace the multi-media feeder. 4. Make sure that you are using the correct paper size in the multimedia feeder. See the section on using the optional multi-media feeder in Appendix A for more information. Note: Make sure you are using paper that meets the specifications for this printer. See Chapter 5 for the correct paper to use.
Paper Jam Problems 2. If the paper is caught just in front of the roller, gently pull the paper out as shown below. 3. If the paper is caught under the roller, first turn the roller forward or backward to free the paper from the roller. Then pull the paper out from under the roller until the page is completely free of the roller. If the paper tears, make sure you remove any pieces remaining in the printer.
Paper Jam Problems 4. If the paper is caught at the fuser area, pull the paper out as shown below. 5. If the paper is caught under both the roller and the fuser, first pull the paper out from under the roller in the direction the paper feeds; then pull it in the opposite direction until it is completely free of the fuser. Note: Because the toner on the paper inside the printer may not have been fixed on the page, it may come off on your hands while you are removing the paper.
Paper Jam Problems 6. If the paper is caught at the paper ejection section, gently pull the paper to remove it. 7. Close the printer. Resume printing when the printer warms up.
Power Supply Power is not being supplied to the printer. After turning on the printer, the display panel remains blank. The power cable may be disconnected or may not be completely plugged into the electrical outlet. Turn off the printer and check the power cable connections between the printer and the electrical outlet; then turn the printer back on. The problem may be with the electrical outlet itself. If the outlet is controlled by an outside source such as a wall switch, make sure it is on.
Printing Problems The printer does not print or stops printing. The ON LINE light is on but nothing is printed. Your computer may not be properly connected to the printer. Perform the section on Testing the computer-to-printer connection in Chapter 2. If the test shows an improper connection, go on to the next three troubleshooting items below. If the test shows a proper connection, skip to the last item in this problem category. The interface cable may not be plugged in securely.
Printing Problems The printer stops printing and the display reads PAPER OUT TONER OUT. or Replace the component specified. See Chapter 5 for paper loading instructions. See Chapter 6 for toner cartridge replacement instructions. The printout is not what you expected. The font you selected with software commands cannot be printed. The correct orientation (portrait or landscape) may not be selected. Make sure that the orientation (portrait or landscape) matches the selected font.
Printing Problems Text is printed with an extra blank line even after you set AUTOFEED to off. Your interface cable may be sending the extra line feed command. Disable the AUTOFEED signal of your interface. See the interface specifications in Chapter 8. Some or all of the output is garbled or printed as asterisks. The interface cable may not be plugged in completely. Make sure that both ends of the cable are plugged in securely. The interface may not be configured correctly.
Printing Problems Even after changing the page length or margin positions, you find that the printed position is not correct. You may need to set the printing position with the T-OFFSET or L-OFFSET settings in the SYSTEM CONFIG menu of SelecType Level 1. This feature allows you to adjust the position of the printable area on the page. See Chapter 4.
Problems With Graphics Graphic images do not print. After changing the printer mode, you are unable to print graphics. You may not have the correct printer driver installed. If you try to print with a software package set for another printer, nothing will be printed. Make sure that the driver matches the currently selected printer mode as described in Chapter 3. You cannot print graphics using the serial interface.
Problems With Graphics The message INSUFF MEMORY appears and graphics cannot be printed. The full print buffer or the receive buffer setting needs to be changed. To correct this error, change the FULL PRINT setting in the SYSTEM CONFIG option of SelecType Level 1 or the RX-BUFFER SIZE setting in SelecType Level 2 as described in Chapter 4. The printer does not have sufficient memory available for the task you have given it.
SelecType Problems SelecType does not function as expected. Settings made with SelecType are ignored. You may not have saved your settings before turning off or resetting the printer. Make sure you save your settings with the SYSTEM CONFIG option SAVE MACRO setting in SelecType Level 1 or with P-CONFIG SAVE in Level 2.
SelecType Problems Desired SelecType settings are nut displayed. You may be trying to select a setting that is not available in the currently selected printer mode. Not all settings are available in all printer modes. For example, you cannot select OPT from the INPUT menu if you haven’t installed the optional multi-media feeder. You may have entered the wrong level of SelecType. Whenever you enter SelecType, you may find it useful to refer to Chapter 4 or the SelecType map on the Quick Reference card.
Paper Handling Paper does not feed properly. Paper does not feed at all. The correct paper cassette may not be selected. If you are using the optional multi-media feeder, make sure the INPUT menu is set to OPT or AUTO. When you select AUTO, the page-size setting in the P-SIZE menu determines whether paper feeds from the standard paper cassette or the multi-media feeder. (The size of the paper in the multi-media feeder is checked first.) See Chapter 4 to change the INPUT setting. The ONLINE light is off.
Paper Handling Poor quality paper can cause paper feeding errors of this type. Make sure your paper supply is not too thin or rough. See Chapter 5 for more information on the types of paper that can be fed automatically and the types that require manual feeding. The paper feeds but then jams at the paper eject area. There may be too much paper in the output tray. Never let more than 50 sheets accumulate in the face-down output tray on top of the printer.
Paper Handling The printer prints a page and then stops. The display reads PAPER SIZE ERROR and the CONTINUE light flashes. You may have selected the wrong paper size with your application software. Check the paper size setting in your software. You may be trying to use a non-standard paper size (one that is not listed on the P-SIZE menu in SelecType Level 1). You may be able to feed this paper manually as described in Chapter 5.
Paper Handling CAUTION: When you press the RESET button, any data remaining in the printer is lost. If you continue to print using paper that is smaller than the size of paper set with your software, toner may accumulate inside the photoconductor unit and damage it. Make sure you set the P-SIZE setting to match the paper you are using. If the AUTO CONT option is on, the paper size error is detected but cleared automatically and printing continues. In most cases, leave AUTO CONT set to off.
Decline in Print Quality If the print quality declines, read through the following section and try to match your problem with the descriptions below. The descriptions may not always match your problem exactly, so try to find one of a similar type. Note: If the print quality problem remains after you work through the suggestions in this section, make a list of the corrective steps you have taken and contact your dealer or a qualified service person for assistance. The print quality is not what you expected.
Decline in Print Quality Vertical black or white bands or lines appear on printed pages. The transfer charger wire may be dirty. Clean the wire as described in Chapter 6. The lens of the toner cartridge may be dirty. Open the front cover, remove the toner cartridge, and place it on a clean, flat surface. Locate the clear lens that runs the length of the cartridge and is located beneath the lengthwise wire screen. Remove the tape on the side of the lens and slide the lens out of the cartridge.
Decline in Print Quality Toner smudges across the printed pages. The bottom of the photoconductor unit may be dirty. Remove the photoconductor unit and wipe the bottom of it with a clean, dry cloth. Then reinstall it as described in Chapter 6. There may be a problem with the toner cartridge. Replace the cartridge as described in Chapter 6. The darkness of the printout is uneven. The transfer charger wire may be dirty. Clean the wire as described in Chapter 6.
Decline in Print Quality Completely blank pages are output. If the TONER LOW message appears on the display, replace the toner cartridge as described in Chapter 6. Check to be sure that the toner cartridge is properly installed as described in Chapter 1. The problem may be with your software program or interface cable. Run a test print or print out a status sheet. If blank pages continue to print, the problem may be with the printer.
Decline in Print Quality The printed image is too dark. The print density knob may not be set correctly. Raise the printer cover and turn the print density knob counterclockwise. See Chapter 2 for information on adjusting the print density knob. If the problem persists, replace the photoconductor unit as described in Chapter 6.
Options Using optional font cartridges, the printer does not operate as expected. The desired font cannot be selected. You may not have inserted the font cartridge correctly. Reinsert the cartridge as described in Appendix B. The correct page orientation (portrait or landscape) may not be selected with SelecType. Only fonts containing the selected orientation are available. See Font Cartridges in Appendix B for more information. Using the optional multi-media feeder, the printer does not operate properly.
Options Several sheets feed into the printer at one time and jam (the FEED JAM or PAPER JAM message appears on the display). You may not be fanning and tapping the stack of paper sufficiently. Remove the jammed paper following the instructions earlier in this chapter. Before reloading paper, be sure to tap the paper and even up the edges of the stack. Also, do not load paper that is creased or folded. You may not be using the correct paper for your printer.
Options The optional interface may not be installed correctly. Turn off the printer and unplug the interface cable and the power cable. Then check to see that the mating connector of the interface is correctly plugged into the main board. See The Optional Interface Board in Appendix A for more information. You may be using the wrong interface cable. Check with your dealer to make sure you have the right cable. Also make sure that you are using a shielded cable.
Data Dump Mode Data dump mode is a special feature that makes it easy for experienced users to find the cause of communication problems between the printer and computer. The data dump mode produces an exact printout of the codes reaching the printer. 1. Make sure that the printer is loaded with paper and turned off. 2. Hold down the SelecType button while you turn on the printer. Make sure you hold the button down until the message HEX DUMP appears on the display. 3.
Data Dump Mode Look at the sample data dump printout shown in Step 3. By reading the characters printed in the text field on the right side of the data dump printout or the printout of hexadecimal codes, you can check what codes are being sent to the printer. In the text field, printable characters appear as their true ASCII characters. Non-printable codes, such as control codes, are represented by dots.
Chapter 8 Technical Specifications Printer Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Printing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper and paper delivery. . . . . . . . . . . . . . . . . . . . . . . . . . Consumable products. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical . . . . . . . . . . . . . . . . . . .
Printer Specifications Printing Printing method: Laser beam scanning and dry electrophotographic process Resolution: 300 x 300 dpi Printing speed: Up to 6 pages per minute for letter-size (depending on the font and quantity of data) First print: Less than 20 seconds with letter (except when the STANDBY mode is on) Warm-up time: 45 seconds or less at normal temperature Internal modes: HP LaserJet series II emulation ESC/P 24-pin printer emulation (LQ-2500) ESC/P 9-pin printer emulation (FX-850/105
Printer Specifications FX and LQ modes Courier 10 cpi Upright/Italic* Courier 12 cpi Upright/Italic* Line printer Upright 16.66 cpi Prestige 12 cpi Upright Prestige 20 cpi Upright M/B P/L M/B P/L M/B* P/L M/B* P/L* M/B* P/L* M: Medium, B: Bold, P: Portrait, L: Landscape * The Italic, Bold, and Landscape effects are created internally. External fonts: Optional fonts provided with font cartridges.
Printer Specifications Paper weight: Plain paper: 60-90 g/m , 16-24 lb 2 Card stock: 90-157 g/m , 24-42 1b 2 Paper size: Paper sizes using SelecType Paper: Type A4 A5 B5 F4 Letter Legal Half-Letter Executive Government Legal Government Letter Size 210 x 297 mm 148 x 210 mm 182 x 257 mm 210 x 330 mm 8.5 x 11 inches 8.5 x 14 inches 5.5 x 8.5 inches 7.25 x 10.5 inches 8.5 x 13 inches 8.0 x 10.
Printer Specifications Printable area: Special sizes: Basically, the paper area within a ¼ inch (6.4 mm) border is the printable area for any paper size. Details for paper sizes using SelecType are shown below.
Printer Specifications HP LJ-2P mode (Units = dots at 300 dpi; I, r, t, b = 50 dots) 8-6 Technical Specifications
Printer Specifications FX and LQ emulation modes (Units = dots at 300 dpi) Technical Specifications 8-7
Printer Specifications Paper feed alignment and direction: Center alignment for all sizes Paper feed: Automatic or manual feed Input paper supply (75 glm2 or 20 lb paper): 100 sheets 150 sheets (optional multi-media feeder) 15 envelopes (optional multi-media feeder) Paper eject: Face-down only Paper eject capacity (75 glm2 or 20 lb paper): 50 sheets Consumable products Toner cartridge (S050002): Storage temperature: 0 to 30°C (32 to 80°F) For less than 20 days -20 to 43°C (4 to 109°F) Storage hum
Printer Specifications Photoconductor unit (S051005): Storage temperature: 0 to 30°C (32 to 80°F) For less than 20 days -20 to 43°C (-4 to 109°F) Storage humidity: 20% to 80% RH For less than 20 days 5% to 95% Shelf life: 18 months after production Life: Photoconductor unit life is up to 30,000 pages. Atmospheric pressure: No less than 740 millibar (about the same as atmospheric pressure at 2500 m or 8200 ft altitude). Example of a 5% print ratio (reduced printout, Letter-size paper).
Printer Specifications Mechanical Dimensions and weight: 177 mm (7.0 inches) 356 mm (14.0 inches)* Width: 479 mm (18.9 inches) 479 mm (18.9 inches)* Depth: 362 mm (14.3 inches) 700 mm (27.6 inches)* Weight: Approx. 13 kg (29 lb.)* Height: * Including paper cassette, photoconductor unit, output tray, and toner cartridge.
Printer Specifications Controller hardware CPU: 68000 (CPU clock 14.1312 MHz) RAM: Standard: 0.5 MB (expandable up to 5.5MB) Environmental Temperature: 0 to 30°C (32 to 80°F) Humidity: 20% to 80% RH Atmospheric pressure: Operating Angle: No less than 740 millibar (about the same as atmospheric pressure at a 2500 m or 8200 ft altitude) Should be kept level.
Interface Specifications The printer has the following resident interfaces: Centronics parallel RS-232C serial Parallel interface Your printer is equipped with an 8-bit parallel interface. Parallel interface pin assignments The parallel interface connector pin assignments and a description of the interface signals are shown in the table below. Signal Pin Return Pin Signal Direction Description 1 19 STROBE IN The STROBE pulse to read data in. Pulse width must be more than 0.
Interface Specifications Signal Pin Return Pin Signal Direction Description 10 28 ACKNLG OUT About a 10-microsecond pulse. LOW indicates data has been received and that the printer is ready to accept more data. This signal is output as a pair with BUSY. 11 29 BUSY OUT A HIGH signal indicates that the printer cannot receive data.
Interface Specifications 8-14 Technical Specifications
Interface Specifications Note: All interface conditions are based on TTL level. Both the rise and fall of each signal must be less than 0.2 microseconds. Data transfer must be carried out by observing the ACKNLG or BUSY signal. (Data transfer to this printer can be carried out only after the receipt of the ACKNLG signal or when the level of the BUSY signal is LOW. The relationship between BUSY and ACKNLG can be changed using SelecType. See Chapter 4.
Interface Specifications Note that it is possible to change the timing between ACKNLG and BUSY. Signal level: TTL compatible Serial interface (RS-232C) Data format Word length: 7 or 8 bits Parity: none, odd or even Stop bits: 1 or 2 Printer ready protocol: enabled (DTR and XON/XOFF protocol set to ON.) The data format can be set using options and menu items in SelecType. Baud rate 300, 600, 1200, 2400, 4800, 9600, 19200 bits per second.
Interface Specifications Serial interface pin assignments The serial interface connector pin assignments and a description of the interface signals are shown in the table below. The direction of signals is given relative to the printer. Signal Pin Signa I Direction Description 1 FG 2 TXD OUT Transmits data. This pin transmits serial data from the printer to the computer. 3 RXD IN Received data. This pin transmits serial data from the computer to the printer. 4 RTS OUT Request to send.
Interface Specifications Handshaking The printer’s serial interface can use DTR (Data Terminal Ready) signal levels and XON/XOFF communication protocols either separately or in combination XON/XOFF protocol When the vacant area for data in the input buffer drops to 128 bytes, the printer outputs an XOFF code, indicating that the printer cannot receive more data.
Initialization There are five types of printer initialization (returning the printer to a fixed set of conditions). All of the printer’s parameters return to the default power-on settings: When the power is turned on. When the power is turned off and, after at least 5 seconds, turned on again. When the CONTINUE button on the printer is pressed until the display shows “INITIALIZE.
Initialization The following tables list the default conditions that become valid when the printer is initialized. The default conditions are different for each printer mode.
Initialization * Item Factory Reset Reset Fonts (both primary and secondary) Symbol set Spacing Pitch Height Style Strokeweight Typeface Roman-8 Fixed 10cpi 12 point Upright Medium Courier * * * * * * * Underline Off Off Font ID 0 0 Character code 0 0 Raster graphic resolution 75 dpi 75 dpi Macro number 0 0 End of line wrap Off Off Display function Off Off Advanced graphics H-size=0, V-size=0, ID=0 H-size=0, V-size=0, ID=0 Symbol set Roman-8 SelecType setting Font numbers
Initialization Default settings in LQ and FX emulation modes Item Factory Reset Reset Paper input Auto SelecType setting Paper size Letter SelecType setting Page length 62 lines Depends on the paper size and orientation settings. Top of form 0.5 inch SelecType setting Left margin Left edge of the printable area. SelecType setting or left edge of the printable area. Right margin 80 columns (10 cpi) Depends on the default right margin set with SelecType.
Initialization Item Underline, Superscript, Subscript, Double-width, Bold Italic Factory Reset Reset off Off Upright Upright Intercharacter 0 spacing 0 Justification Off Off DC 1, DC 3 DC 1 DC 1 MSB Enable Enable Technical Specifications 8-23
Option Specifications Multi-media feeder Electrical Power supply: Insulation resistance: DC 24 V supplied by the printer 10 Mohm minimum Dielectric strength (between AC line and chassis): Can withstand 1250 VAC rms for one minute. Paper and paper delivery Paper Width: 98-216 mm (3.86-8.50 inches) Size: Paper Length: 148-356 mm (5.83-14.
Option Specifications Mechanical Dimensions and weight: Without the printer: Height: Width: Depth: 175 mm (6.9 inches) 326 mm (12.8 inches) 384 mm (15.
Appendix A Options The Multi-Media Feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the multi-media feeder . . . . . . . . . . . . . . . . . . Loading paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating the multi-media feeder . . . . . . . . . . . . . . . . . . A-2 A-2 A-5 A-7 The Optional Interface Board . . . . . . . . . . . . . . . . . . . . . . . . Installing the interface board . . . . . . . . . . . . . . . . . . . . . .
The Multi-Media Feeder The optional multi-media feeder handles automatic feeding of many types of paper. It holds up to 150 sheets of paper, and it can feed paper from 98 to 216 mm (3.86 to 8.50 inches) wide and from 148 to 356 mm (5.83 to 14.0 inches) long. You can load two different sizes of paper in your printer at once (one size in the multi-media feeder and the other in your standard paper cassette).
The Multi-Media Feeder 1. Remove the manual feed paper guide. 2. Attach the multi-media feeder as shown below. Then, mount the multi-media feeder safely on the printer.
The Multi-Media Feeder 3. Move the paper guide on the multi-media feeder as shown below. 4. Open the lid of the multi-media feeder.
The Multi-Media Feeder Loading paper 1. To load paper into the multi-media feeder, first raise up the paper cover. 2. Adjust the paper guides to match the paper size you are using, as shown below.
The Multi-Media Feeder 3. Take a stack of paper and fan it. Tap the edges of the paper on a flat surface to even up the stack. 4. Insert a stack of paper into the multi-media feeder, making sure the top of stack does not exceed the maximum height of the paper guide, as shown below. Gently push the paper in as far as it will go. Note: You can load up to 15 envelopes in the multi-media feeder. Be sure to load them lengthwise and face-down.
The Multi-Media Feeder 5. Close the paper cover. Operating the multi-media feeder To feed paper from the multi-media feeder automatically, you need to change the paper source with your application software, or you can change the INPUT menu in SelecType Level 1. Also, you may need to change the paper size with your application software or with the P-SIZE menu in SelecType Level 1 to match the paper size in the multi-media feeder. See Chapter 5, Changing the paper size setting.
The Multi-Media Feeder 3. Press to change the feeding method. 4. Press or to choose the feeding method. Two of the feeding methods can select the multi-media feeder. STD Standard feeds from the paper cassette OPT Option feeds from multi-media feeder AUTO Auto select feeds from the paper stock for suitable paper size Note: AUTO feeding selects the multi-media feeder if both the paper sizes in both the standard cassette and multi-media feeder are the same. 5. Press 6.
The Multi-Media Feeder Note: The new paper setting is effective only temporarily in the current printer mode unless you use SelecType’s Level 1 SAVE MACRO setting so the paper size you use most often is automatically selected whenever you turn on, reset, or initialize your printer. See Chapter 5, Saving the new paper-size setting. Depending on your application software, you may need to select the multi-media feeder using your software, rather than with SelecType.
The Optional Interface Board You can use one of the following optional interface boards for your printer. For information on other types of interface boards, contact your Epson dealer. Available interface boards: 32 Kbyte serial interface (C823071) 32 Kbyte Parallel interface (C823101) Installing the interface board To install an optional interface board, you need a cross-head screwdriver.
The Optional Interface Board 3. Insert the interface board by sliding it along the guides in the printer. Push firmly on the board until it locks in place. 4. Hand-tighten the screws on the interface board until snug. 5. Turn the printer around. Then attach the proper interface cable to the computer and to the optional interface connector. 6. Make sure the printer is turned off. Then plug the power cord into the printer.
The Optional Interface Board Before you use the interface board, you may need to change the printer mode and the interface connection with SelecType, but if you are using the SelecType default of AUTO-SENSE, you probably will not need to change any SelecType settings. The optional interface can be selected as Channel O. See Chapter 4 for information on using SelecType to change printer modes for Channel O.
The Memory Expansion Board You probably need to add memory if you have trouble printing complex or graphics-intensive pages, or if any of the following messages appear often: INSUFF MEMORY, PAGE BUFFER FULL, or ADD MEMORY. Using the INDIVIDUAL setting in the CH mode in SelecType also requires additional memory. To add memory, you need the optional OK memory board and enough memory chip sets to equal the amount of memory that you want to add.
The Memory Expansion Board Installing RAM chips on the memory board There are four sectors on the memory board, each with four chip sockets, as shown below. There are three ways to install chip sets on this board. 0.5MB chip sets in blocks A, B, C, and D A 2.0MB chip set in block A, and 0.5MB chip sets in blocks B, C, and D 2.0MB chip sets in blocks A and B, and 0.
The Memory Expansion Board After you have bought the chip sets and decided where to install them, follow the steps below: 1. Locate the DIP switches on the memory board and make sure that switches 1 and 2 are off, as shown below. 2. Set the remaining DIP switches on the memory board according to the following table: DIP Switch Block ON 1 Always off 2 Always off OFF 3 A 2.0MB 0.5MB 4 B 2.0MB 0.5MB 5 C 2.0MB 0.5MB 6 D 2.0MB 0.
The Memory Expansion Board 3. Make sure that all the pins on each chip are straight. The pins should point inward at slightly less than a 90° angle as shown below. If any of the pins are bent, straighten them by gently pushing them back into alignment with the other pins. 4. Align the pins with the holes in the socket. Be sure that the small notch on the end of the chip is facing in the direction shown below. 5. Gently press the chip halfway into the socket.
The Memory Expansion Board CAUTION: Be careful not to scratch the chip or the board when removing the chip. 6. With the chip properly inserted, push down firmly on both ends of the chip to make sure it is well-seated. 7. Repeat steps 3 through 6 for each of the three remaining chips. Installing the board To install the memory expansion board, you need a cross-head screwdriver. WARNING: Do not remove any screws other than the brass-colored screws specified in the following steps.
The Memory Expansion Board 1. Unplug the power cable from the printer. 2. Disconnect all interface cables from the rear of printer. 3. Remove the two brass-colored retaining screws and the memory board cover located on the right side of the printer. Keep the screws and the cover in a safe place. 4. Insert the optional memory board (with memory chips installed) into the printer. Make sure the connectors fit together securely.
The Memory Expansion Board 5. Secure the board using the four screws attached to the memory board. 6. Replace the cover over the memory board as shown below and secure it with the two brass-colored retaining screws.
The Memory Expansion Board Checking the board Complete the following steps to make sure that the memory expansion board is installed properly and is functioning correctly. 1. Turn on the printer power and watch the display for the following: All the indicator lights on the display light briefly. The message ROM Check appears. The message RAM Check x.x MB appears. 2.
Optional Epson GL Identity Card The Epson GL Identity card allows you to install the Epson GL printer mode on your printer. The printer has one slot for identity cards. The optional Epson GL Identity card requires a minimum of 1MB additional memory. To add memory, see page A-13. Compatible cards In addition to the Epson GL Identity card, other cards may be available for use with your printer. Check with your dealer for a list of the cards.
Optional Epson GL Identity Card Inserting a card You can insert a card into the slot on the right side of the printer. CAUTION: Never insert or remove a card while the printer is on line, in SelecType mode, or while the printer is resetting (after you press RESET). Be careful when you insert or remove a card. You can damage the card by trying to insert it the wrong way or by using too much force. 1. Make sure that the printer is not in one of the following conditions: The FEED light is flashing fast.
Optional Epson CL Identity Card 5. Gently slide the card into the slot as shown below. CAUTION: If the message REMOVE CARD appears on the display, you inserted the card when the printer was on line or when the printer’s memory contained data. If you see this message, remove the card, press CONTINUE, then return to step 1. 6. If the power is on, press ON LINE to set the printer on line. If the power is off, turn on the printer.
Optional Epson GL Identity Card Using the Epson GL identity card To run the EPSON GL printer mode after inserting the identity card, follow these steps: 1. Press SelecType until SelecType LEVEL2 appears on the display. 2. Press 3. until MODE ASSIGN appears. Press . 4. Press or to select a channel for Epson GL mode. 6. Press or until EPSON GL appears. 7. Press to set the mode. 5. Press . 8. To exit SelecType, press the SelecType button.
Optional Epson GL Identity Card Removing a card CAUTION: Never remove a card while the printer is on line, in SelecType mode, or while the printer is resetting. If you remove a card while the-printer is in one of these states, a REINSERT CARD message appears on the display. An error also occurs if you remove a card while the FEED light is on, even if the printer is off line. See the description of card error messages in Chapter 7 for more information. 1.
Optional Epson GL Identity Card Recovering from a card error When the display shows one of the following messages, a card error has occurred: REINSERT CARD ILLEGAL CARD #X REMOVE CARD MEMORY OVERFLOW INSUFF MEMORY A card error occurs if you insert or remove a card when the printer is on line or when the printer’s memory contains data. You cannot use the card or print documents until you correct the card error. For the steps required to clear each error message, see Status and Error Messages in Chapter 7.
Appendix B Font Cartridges Available Font Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . B-2 Using the Font Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . Inserting a font cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . Selecting a font with your application program. . . . . . . Removing a font cartridge . . . . . . . . . . . . . . . . . . . . . . . . .
Available Font Cartridges This printer can use any of the font cartridges listed below when the HP LaserJet IIP emulation mode is selected. By using font cartridges, you can select many different styles of type in addition to the resident fonts in your printer. The manual for each font cartridge contains samples of the characters and symbol sets the font cartridge provides. Note: Some of the fonts contained on these font cartridges are duplicated by the resident fonts in the printer.
Supplier Cartridge number Cartridge HP (continued) C2053A C2053A C2053A C2053A C2053A C2053A C2053A C2053A #CO1 WordPerfect #CO2 Microsoft #CO3 Polished Worksheets. #CO4 Persuasive Presentations #CO5 Forms Etc.
Using the Font Cartridges Inserting a font cartridge You insert a font cartridge into the slot on the front of the printer. CAUTION: Never insert or remove a cartridge while the printer is on line, in SelecType mode, or while the printer is resetting (after you press RESET). Be careful when you insert or remove a font cartridge. You can damage the cartridge by trying to insert it the wrong way or by using too much force. 1.
Using the Font Cartridges 4. Hold the cartridge so that the label on the cartridge faces left as shown below. 5. Press firmly until the cartridge locks into place.
Using the Font Cartridges CAUTION: If the message REMOVE CARD appears on the display, you inserted the cartridge when the printer was on line or when the printer’s memory contained data. If you see this message, remove the cartridge, press CONTINUE; then return to step 1. 6. If the power is on, press ON LINE to set the printer on line. If the power is off, turn on the printer.
Using the Font Cartridges Removing a font cartridge CAUTION: Never remove a font cartridge while the printer is on line, in SelecType mode, or while the printer is resetting. If you remove a card while the printer is in one of these states, a REINSERT CARD message appears on the display. An error also occurs if you remove a cartridge while the FEED light is on, even if the printer is off line. See the description of card error messages in Chapter 7 for more information. 1.
Using the Font Cartridges 4. Grasp the edges of the cartridge and slowly pull it from the slot. 5. Turn on the printer or press ON LINE to set the printer on line.
Appendix C Character Samples and Symbol Sets Available Fonts and Symbol Sets . . . . . . . . . . . . . . . . . . . . . C-2 Resident fonts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-2 Symbol sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 HP Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resident fonts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Symbolsets . . . . . . . . . . . . . .
Available Fonts and Symbol Sets This appendix describes the printer’s resident fonts and available symbol sets in HP LaserJet IIP and Epson LQ/FX emulation modes. Resident fonts The following table lists the resident bitmap fonts in the printer and the printer modes that support these fonts. Character samples of each font are included later in this appendix.
Available Fonts and Symbol Sets Symbol sets Your printer can access a variety of symbol sets. Many of these symbol sets differ only in the international characters specific to each language. Not all symbol sets are available in all modes. The following table lists the symbol sets and the modes that can access those sets. This appendix provides character tables for the symbol sets available in each mode. The tables show both the characters and their hexadecimal values.
HP Emulation Mode This section describes the resident fonts and symbol sets available in HP emulation mode. Resident fonts The printer offers a variety of resident fonts in HP emulation mode. The following table lists the resident fonts available in HP emulation mode and shows samples of text printed with them.
HP Emulation Mode ISO ANSI ASCII Set (Symbol Set ID #OU) 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9 A B C D E F Note: For the shaded areas, see the international character table for that set.
HP Emulation Mode International Set for ISO Sets Name ISO 6 ANSI ASCII 0U ISO 2 IRV 2U ISO 4 ISO 10 United Kingdom 1E Swedish 3S ISO 11 Swedish 2 0S ISO 14 JIS ASCII OK ISO 15 Italian 0I ISO 16 Portuguese 4S ISO 17 Spanish 2S ISO 21 German 1G ISO 25 French OF ISO 57 Chinese 2K ISO 60 Norwegian v1 0D ISO 61 Norwegian v2 1D ISO 69 French 2 1F ISO 84 Portuguese IBM 5S ISO 85 Spanish IBM 6S HP German 0G HP Spanish 1S C-6 Character Samples and Symbol S
HP Emulation Mode HP Roman-8 Extension (Symbol Set ID 0E) HP Legal Set (Symbol Set ID #1U) Character Samples and Symbol Sets C-7
HP Emulation Mode ISO 100 ECMA-94 Latin-1 (Symbol Set ID #0N) C-8 Character Samples and Symbol Sets
HP Emulation Mode HP Roman-8 Set (Symbol Set ID #8U) Character Samples and Symbol Sets C-9
HP Emulation Mode HP IBM-US Set (Symbol Set ID #10U) IBM-US (#10u) IBM-DN (#11u) C-10 Character Samples and Symbol Sets
HP Emulation Mode PC Multilingual (Symbol Set ID #12U) Note : <01>H to <14>H and <16> H to <1F>H cannot be printed in ESCP emulation modes.
LQ and FX Emulation Modes This section describes the resident fonts and symbol sets available in LQ and FX emulation modes. Resident fonts The printer offers a variety of resident fonts in LQ and FX emulation modes. The following table lists the resident fonts available in LQ and FX emulation modes and shows samples of text printed with them.
LQ and FX Emulation Modes Character sets This section provides character tables for the character sets available in LQ and FX emulation modes. The tables show both the characters and their hexadecimal values. Epson Italic Character Table Note: You do not need to select the italic character table to print italics. You can print italics when out of the other character tables is selected.
LQ and FX Emulation Modes Pc USA C-14 Character Samples and Symbol Sets
LQ and FX Emulation Modes The following tables show the characters that differ from PC USA.
LQ and FX Emulation Modes International Characters for Countory U.S.A. France Germany U.K.
Converting Hexadecimal Numbers to Decimals If you prefer to use decimal numbers instead of hexadecimal numbers, you can convert them with the chart below. Just read down in the column for the first digit of the hexadecimal value and across in the row for the second digit. The decimal value that corresponds to your hexadecimal number is at the intersection of the column beginning with the hexadecimal number’s first digit and the row beginning with the hexadecimal number’s second digit.
Appendix D Printer Modes D-2 Available Printer Modes . . . . . . . . . . . . . . . . . . . . ....................... HP Emulation Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3 Operating as an HP LaserJet IIP printer . . . . . . . . . . . . . . D-4 HP emulation command summary . . . . . . . . . . . . . . . . . . D-5 LQ and FX Emulation Modes . . . . . . . . . . . . . . . . . . . . . . . . D-12 Operating as an LQ or FX series printer . . . . . . . . . . . . . .
Available Printer Modes Your printer comes with the following resident printer modes: HP LaserJet IIP Epson LQ Epson FX This appendix gives you information on how to operate your printer as an HP LaserJet series IIP, Epson LQ-2500, or Epson FX-800/1000 (FX-86e/286e) printer. It also describes the differences between modes and provides you with a list of the printer commands used in each mode. To change the printer mode, enter the SelecType Level 2 MODE ASSIGN option.
HP Emulation Mode HP emulation allows you to use commercial software designed for the HP LaserJet IIP printer. This means you can connect your printer to a computer configured for an HP LaserJet IIP printer without having to modify computer software. This section gives you information about using HP emulation. It describes the unique features of your printer’s HP emulation as well as the differences between your printer’s HP emulation and printing with the HP LaserJet itself.
HP Emulation Mode Operating as an HP LaserJet IIP printer Operating the printer in HP emulation mode differs slightly from operating a LaserJet IIP because the two printers use different technologies. The differences in printing are explained below.
HP Emulation Mode Printable area The size of the printable area for the LaserJet IIP and this printer is the same. The maximum number of characters that can be printed per line is also the same. However, the absolute print position may not be exactly the same as a printout from an HP LaserJet IIP printer.
HP Emulation Mode All commands closely emulate the LaserJet IIP except for the following: ESC &1#A can be used to select the following eight paper sizes: A4 Letter Legal Executive Monarch Commercial 10 DL C5 This command overrides the P-SIZE setting in SelecType. Other paper sizes cannot be specified with this command. ESC &1#H command cannot be used to specify manual paper feeding. The values for # produce the effects in the following table.
HP Emulation Mode Printer commands arranged by topic The HP printer commands supported in HP LaserJet IIP emulation are listed below.
HP Emulation Mode Symbol set IS0 14: JIS ASCII HP Katakana IS0 57: Chinese HP Kana 8 HP Korean 8 HP Line Draw HP Block Character HP Math7 Technical HP Math8 IS0 100: ECMA94 Latin-1 OCR-A OCR-B APL (Typewriter) APL (Bit Paired) HP Math-8a HP Math-8b HP Pi Font-a OCR-B Extended PC LINE HP Cyrillic ASCII HP Cyrillic IS0 11: Swedish Names HP Spanish IS0 17: Spanish IS0 10: Swedish ISO 16: Portuguese IS0 84: Portuguese IBM IS0 85: Spanish IBM HP Thai 8 HP Turkish 8 IS0 6: ANSI ASCII HP Legal ISO 2: IRV HP HPL L
HP Emulation Mode Symbol set OEM-1 HP Roman-8 Windows IBM-US IBM-Denmark/Norway PC Multilingual (CP850) HP Pi Font HP Arabic (McKay’s Version) HP Arabic Bar-Code 3 of 9 EAN/UPC Spacing Pitch (cpi) Point size Style Stroke weight Typeface Primary ESC(7U ESC(8U ESC(9U ESC(10U ESC(11U ESC(12U ESC(15U ESC(0V ESC(8V ESC(0Y ESC(8Y ESC(s#P ESC(s#H ESC(s#V ESC(s#S ESC(s#B ESC(s#T Secondary ESC)7U ESC)8U ESC)9U ESC)10U ESC)11U ESC)12U ESC)15U ESC)0V ESC)8V ESC)0Y ESC)8Y ESC)s#P ESC)s#H ESC)s#V ESC)s#S ESC)s#B ESC
HP Emulation Mode Half-line feed: Half-line feed ESC = Raster graphics: Raster graphics resolution Start raster graphics Transfer raster graphics End raster graphics ESC*t#R ESC*r#A ESC*b#W[data] ESC*rB Specialized printer control: Printer reset Status sheet print ESC E ESC z Cursor positioning: Horizontal (columns) Vertical (lines) Horizontal (decipoints) Vertical (decipoints) Horizontal (dots) Vertical (dots) ESC&a#C ESC&a#R ESC&a#H ESC&a#V ESC*p#X ESC*p#Y Underline: Enable auto-underlining D
HP Emulation Mode Miscellaneous: Horizontal motion index Line termination End of line wrap Select number of copies Paper input control ESC&k#H ESC&k#G ESC&s#C ESC&1#X ESC&1#H Font management: Specify font ID Specify character code Font and character control Download character Create font (font descriptor) Designate downloaded font (primary) (secondary) Font default (primary) (secondary) ESC*c#D ESC*c#E ESC*c#F ESC(s#W [data] ESC)s#W [data] ESC(#X ESC)#X ESC(3@ ESC)3@ Macros: Macro ID Macro control
LQ and FX Emulation Modes Your printer has the ability to emulate an Epson LQ-2500 or FX-800/1000 (86e/286e) series printer. This means that you can connect your printer to a computer set up for an Epson LQ or FX printer and print without having to modify the software controlling your printer. Besides allowing you to use software for an LQ or FX printer, you also gain the advantages of the quality text, sharper graphics, and faster printing provided by this printer.
LQ and FX Emulation Modes The following commands are either not available or are ignored in LQ or FX emulation mode: ESC < ESC 8 ESC 9 ESC U ESC s ESC r ESC i Unidirectional mode (one line) Disable paper end detector Enable paper end detector Select print direction Set/cancel half-speed printing Select color printing Incremental view The following commands are available in FX mode but not in LQ mode: ESC 1 ESC ^ ESC I 7/72-inch line feed Select 9-pin graphics mode Select character code table The follow
LQ and FX Emulation Modes ESC x This command is normally used to select between draft and LQ quality with an LQ or FX series printer. However, this command has no effect on your printer’s print quality since all characters are printed at 300 dpi (dots per inch) Letter Quality.
LQ and FX Emulation Modes ESC C, ESC C0 When you send the ESC C or ESC CO command to change the page length on LQ or FX printers, you can print more than one page on the same sheet of paper. Because your printer processes data pageby-page, each page must be printed on a separate sheet of paper, so exact LQ or FX emulation cannot be provided. Problems will occur when the page length set with the ESC C or ESC CO command differs from the actual page length.
LQ and FX Emulation Modes Data control: Cancel line CAN MSB control ESC = ESC > ESC # Set MSB to 0 Set MSB to 1 Cancel MSB control Vertical motion: Form feeding FF ESC C ESC C0 ESC EM ESC N ESC O Line feeding LF ESC 0 ESC 1 ESC 2 ESC 3 ESC A ESC J ESC j Vertical tabbing VT ESC B ESC b ESC / D-16 Form feed Set page length in lines Set page length in inches Control cut sheet feeder Set skip over perforation Cancel skip over perforation Line feed Select 1/8-inch line spacing Select 7/72-inch line spa
LQ and FX Emulation Modes Horizontal motion: Margins ESC 1 ESC Q Horizontal tabbing HT ESC D Set left margin Set right margin Tab horizontally Set horizontal tabs Print position: CR BS ESC \ ESC $ Carriage return Backspace Set relative position Set absolute print position Overall printing style: ESC x ESC k ESC ! Select letter quality or draft Select typestyle family Master select Print size and character width: ESC g ESC P ESC M ESC p SI ESC SI DC2 so ESC SO ESC W DC4 ESC w Select 15 cpi Sele
LQ and FX Emulation Modes Print enhancement: Select emphasized mode Cancel emphasized mode Select double-strike mode Cancel double-strike mode Select superscript/subscript mode Cancel superscript/subscript mode Turn underline mode on/off ESC E ESC F ESC G ESC H ESC S ESC T ESC Word processing: Select justification Set intercharacter space ESC a ESC SP Character tables: Select character table Select italic mode Cancel italic mode Select an international character set Printable code area expansion (FX mo
Glossary application program Any software program designed to carry out a particular task. For example, word processing and graphics packages are application programs. ASCII American Standard Code for Information Interchange. A standardized way of assigning numerical codes to characters and control codes. The system is widely used by manufacturers of computers, printers, and software.
bold A print enhancement that produces darker than normal characters and is typically used to add emphasis to a document. Bold is also offered as a font attribute. buffer See memory. byte A unit of information consisting of eight bits. A byte usually corresponds to one character or code. character set A collection of letters, numbers, and symbols. character spacing Refers to two methods for horizontal character placement-fixedpitch and proportional spacing.
download font A font that is loaded into the printer’s memory from an outside source, such as a computer. dpi Dots per inch. This is a measure of print resolution. driver The part of an application program that converts commands from the program into commands used by the printer. Also known as the printer driver. EEPROM Electrically Erasable Programmable Read Only Memory. The portion of the printer’s memory holding SelecType’s default settings.
fixed pitch Refers to the character spacing of a font in which the width is the same for all characters, as distinguished from proportional spacing. For fixed-pitch fonts, narrow characters such as lowercase i take up as much space as wider characters such as uppercase W. hex dump mode A printing mode that can be used to print out the exact codes reaching the printer. This mode can be used by experienced users as a troubleshooting tool.
line space The distance between lines of text. memory The part of the printer’s electronic system that is used to store information. Some information is fixed and is used to control how the printer operates. Information that is sent to the printer from the computer (such as download fonts and graphics) is stored temporarily until it is printed out. See also EEPROM, RAM, and ROM. nonvolatile memory The portion of the printer’s memory that is not lost when you turn off the printer.
parallel interface See interface. Parity A method of checking the reliability of data transmission between the computer and printer. pitch A measure of character width. Characters can be fixed pitch, where the width is the same for all characters, or proportionally spaced, with varying widths. Pitch is a measure of the number of characters per inch (cpi) for fixed-pitch fonts. point size The height of a particular typeface as measured from the top of the tallest character to the bottom of the lowest.
proportional spacing Printing in which character width varies from character to character. For example, a capital W receives much more space than a lowercase i. The result looks more like a typeset book than a typewritten draft. RAM Random Access Memory. The portion of the printer’s memory used as an input buffer and for storing user-defined characters, downloaded fonts, and graphics images. Information stored in RAM is volatile and is lost when printer power is interrupted.
symbol set A collection of symbols (letters, numbers, and special characters) used by a font. Symbols are assigned to specific codes in a character table. test print A method of checking the operation of the printer. When a test print is performed with the SelecType feature, the printer prints out one of the two test patterns (vertical or horizontal lines). toner A dry, powder-like substance composed of resin and pigment. Toner is used to form the image during the printing process.
Index A Adjusting the print density, 2-10-12 Arrow buttons, 4-6 Assembling the printer, 1-7-20 Attaching the power cord, 1-18-19 AUTO CONT function, 4-4, 4-31 B Buttons, control panel, 2-4-5, C Carrying the printer, 1-6 CH function, 4-4, 4-29-30 CH TIMEOUT function, 4-4, 4-31 CHANGE PCU message, 6-2, 6-10, 7-3 Character samples and symbol sets, C-1-18 Choosing a font, 4-34-35 an interface, 2-14 paper, 5-14 paper size, 5-11-13 Cleaning printer case, 6-17 transfer charger wire, 6-9-10 Connecting parallel
E Emulation modes, see Epson and HP Envelopes, 5-4 Epson LQ and FX emulation modes, 3-2-4, 4-35, 4-38-44, 8-7, 8-22-23, C-12-16, D-12-18 character sets, C-13-16 printer modes, D-12-18 resident fonts, C-12 Epson GL identity card, optional, 5, A-21-26 Error handling, 8-18 messages, and status, 2-2, 7-2-7 F FACTORY RESET function, 4-4, 4-32 FEED indicator light, 2-3 FEED JAM, 7-3, 7-10-12 FEED MANUAL button, 2-5 Font cartridges, B-1-8 available, B-2 inserting, B-4-5 removing, B-7-8 selecting a font, B-6 using,
Installing multi-media feeder, A-24 optional interface board, A-10-12 output tray, 1-14 paper cassette, 1-15-17 photoconductor unit, 1-7-10 toner cartridge, 1-11-13 INSUFF MEMORY, 7-22 Interface choosing, 2-14 specifications, 8-12-18 L Labels, 5-3 Laser printer precautions, 6 LOAD MACRO, 4-18 Loading and installing paper cassette, 1-15-17 paper in cassette, 5-7-10 paper, manually, 5-1 4-16 L-OFFSET, 4-18 LQ and FX emulation modes, 3-2-4, 4-35, 4-38-44, 8-7, 8-22-23, C-12-16, D-12-18 character sets, C-13-16
Output tray, installing, 1-14 Ozone filter, 6-8-9, 8-9 P Packing for transportation, 6-18-21 PAGE COUNTER function, 4-4, 4-33 Paper choosing, 5-2-4 choosing size, 5-11-13 handling, 5-1-16, 7-25-28 jam problems, 7-8, 7-10-15, 7-25-26 loading manually, 5-14-16 size, 8-4 specifications, 8-3-8 Paper cassette cautions, 1-17 legal, 2 loading and installing, 1-15-17,5-7-10 PAPER JAM, 7-4, 7-12-15 Paper size choosing, 5-11 setting, 5-12 Paper-feed method, 5-5-6 PARALLEL function, 4-23-24 Parallel interface, 2-13 c
R RAM, 4-16-17, A-14-16 Removing a font cartridge, B-6-7 Replacing consumable parts, 6-2-16 ozone filter, 6-8-9 photoconductor unit, 6-10-16 toner cartridge, 6-3-7 RESET button, 2-4-5 Resident fonts, C-2 RX-BUFFER SIZE function, 4-4, 4-28 S SAVE MACRO, 4-19, 4-35 Saving new paper-size setting, 5-12-13 Selecting a font with your application program, B-5 and printing a status sheet or test print, 2-8-10 SelecType button(s), 2-4, 4-6 display, 4-6 Level 1 functions, 4-2-3, 4-11-20 Level 2 functions, 4-2, 4-4, 4
T U Technical specifications, 8-1-25 Test file, printing, 3-5 print, selecting and printing, 2-8 TEST PRINT function, 4-4, 4-21 Testing and connecting your printer, 2-1-20 parallel connection, 2-17-18 printer, 2-6-12 Thin paper, 5-6 Tips for first-time laser printer user, 8-10 T-OFFSET, 4-17 Toll-free number, Intro-10 Toner cartridge, 1-7,6-2 cautions, 1-12 installing, 1-11-13 replacing, 6-3-7 specifications, 8-8 TONER LOW message, 6-2, 7-7, 7-32 TONER OUT message, 6-2-3, 7-7 Transfer charger wire, cleani
Quick Reference SelecType Map The following menu maps show the possible menus and options in SelecType. Mode-specific options, those marked “refer to mode,” are listed under each printer mode later on this card. See Chapter 3 for a description of each option.
SelecType Level 1 in LJ-2P mode FONT RD - 0 to available (A) - 0 to available (C) - 0 to available DL* SUB CONFIG.
SelecType Level 1 in LQ and FX modes FONT Courier Prestige (OCR-B) (OCR-A) DL* SUB CONFIG. PITCH 10 12 15 PROP. CONDENSED ON/OFF L-MARGIN R-MARGIN 0 to available 1 to available FORM TOP 0.50 TO 1.50 TEXT 62LINES [1 to available] SKIPBOTTOM ON/OFF CGTABLE ITALIC PcUSA PcMult PcPort COUNTRY USA France German UK Denmak Sweden Italy J-REPRINT AUTO CR ZERO CHAR.
SelecType Level 1 CANCEL:< S:^ P:V 0: > INPUT STD (OPT) A U T O P-SIZE COPIES ORIENT. Letter A5 EXE B5 F4 LETTER MONARCH HALF LT C10 LEGAL D L GLT C 5 GLG [OTHER] 1 - 99 PORT LAND FONT Refer to mode STATUS SHEET FONT SAMPLE SUB CONFIG. Refer to mode SYSTEM CONFIG.
SelecType Level 2 TEST PRINT PATTERN 1 PATTERN 2 MODE ASSIGN CH X mode LJ-2P L Q F X (EPSON GL) I/F CONFIG. CH X CONFIG. [CH P] SLCTIN AUTOFEED BUSY DELAY [CHS] WORD LENGTH BAUD RATE PARITY STOP BIT DTR XON/XOFF ENQ/ACK DSR CTS RX-BUFFER SIZE 1 TO 99 C H CH AUTOSENSE CH INDIVIDUAL — nMS:t P:u O:v – t.i.v: 0 to 9 CH TIMEOUT 10 TO 50, 60, 70 to 600 [step 10] AUTO CONT. O N OFF P-CONFIG.
Epson America, Inc. 20770 Madrona Avenue, Torrance, CA 90503 Printed in Japan 91.
