TM U220 Printers User’s Manual / Bedienungsanleitung Gebruikershandleiding / Manuel d’utilisation Manual do utilizador / Manual del usuario Manuale dell’utente / Руководство пользователя
A Type B Type A 1 3 B C ii 4 2 Type D
D E F G G-a H iii
I J K L M N iv
O P v
DIP Switch Tables Look at the numbers and letters in the area indicated in the illustration. If the last letters are “US”, use the “US” tables below. If the last letters are “STD”, use the “STD” tables. CAUTION: Be sure to replace the DIP switch cover before using the printer.
STD Serial (DIP Switch 1) Parallel (DIP Switch 1) SW Function On Off SW Function On 1 Data receive error Ignored Prints “?” 1 Auto line feed Enabled 2 Receive buffer capacity 40 bytes 4 KB 2 Receive buffer capacity 40 bytes 4 KB Off Disabled 3 Handshaking XON/XOFF DTR/DSR 3~7 Undefined - - 4 Word length 7 bits 8 bits 8 BUSY condition 5 Parity check Yes No Receive buffer full 6 Parity selection Even Odd Receive buffer full or Offline 7 Transmission speed 4800
TM-U220 Specifications Print method Print font Paper 9-pin serial impact dot matrix method Font (standard) Font A: 7 × 9, Font B: 9 × 9 Column capacity (columns) 7 × 9/9 × 9: 76 mm: 40/33 69.5 mm: 36/30 57.5 mm: 30/25 Character size (W u H) (standard) 1.2 × 3.1 mm/1.6 × 3.1 mm (not including horizontal spacing) Character set 95 Alphanumeric, 48 International,128 × 12 Graphic Characters per inch (standard) (3 half dot spacing) Font A (7 × 9): 16 cpi, Font B (9 × 9): 13.3 cpi Dimensions (mm) 57.
English TM-U220 Printers User’s Manual DIP Switches and Specifications The technical specifications and the information about the DIP switches are at the beginning of this manual. Illustrations All of the illustrations are at the beginning of this manual. They are identified by letters (A, B, C . . .). In the text the illustrations are referred to by these letters. (“See illustration A,” for example.) Some of these illustrations have numbered arrows or lines pointing to parts of the illustration.
English EMC and Safety Standards Applied Product Name: TM-U220A/TM-U220B/ TM-U220D Model Name: M188A/M188B/M188D The following standards are applied only to the printers that are so labeled. (EMC is tested using the EPSON power supplies.) Europe: CE marking Safety: TÜV (EN 60950) North America: EMI: FCC/ICES-003 Class A Safety: UL 60950/CSA C22.2 No.
English Safety Precautions WARNING: Shut down your equipment immediately if it produces smoke, a strange odor, or unusual noise. Continued use may lead to fire. Immediately unplug the equipment and contact your dealer or a Seiko Epson service center for advice. Never attempt to repair this product yourself. Improper repair work can be dangerous. Never disassemble or modify this product. Tampering with this product may result in injury or fire. Be sure to use the specified power source.
English Notes on Usage ❏ Do not open the cover during printing or when the autocutter is being operated. ❏ Do not install the printer in a dusty place. ❏ Protect the printer from impact. ❏ Cords or other foreign objects must not be caught on the printer. ❏ Do not apply excessive force to the printer case. ❏ Do not place food or beverages such as coffee on the case of the printer. Notes on Installation ❏ When using the printer, be sure that the printer is installed horizontally.
English Features of Printer Types See illustration A. Type A Type B Type D Two color printing Yes Yes Yes Autocutter Yes Yes No Take up device Yes No No Paper width (mm) 76 76/69.5/57.5 76/69.5/57.
English Buttons FEED FEED feeds the roll paper. Note: Paper cannot be fed by using this button when a paper out is detected. Power Supply Switch and Power Supply Switch Cover The power supply switch is on the front of the printer. Press the power supply switch to turn on the printer. Power Supply Switch Cover You can use the enclosed power supply switch cover to make sure that the power supply switch is not accidentally pressed. Just press the cover into place to install it.
English 3. Insert the ribbon in the position shown in illustration F and push the ribbon cassette down until it clicks. Note: Make sure the ribbon is installed between the print head and the platen without wrinkles or creases. 4. Again turn the ribbon cassette’s knob 2 or 3 times in the direction of the arrow and close the ribbon cassette cover. CAUTION: Be careful not to touch the print head with your fingers when turning the ribbon cassette knob because the print head is hot and you might be burned.
English 8. Insert the end of the bottom paper (journal paper) into the paper take-up spool, as shown in illustration M. 9. Insert the paper take-up spool in the printer. Be sure that the paper is aligned with the spool’s flange, as shown in illustration N. 10. Feed the paper with the FEED button so that the paper is taken up by the spool. 11. Close the roll paper cover and tear off the roll paper with the manual cutter, as shown in illustration O.
English ERROR LED is flashing or lit ❏ The print head temperature may be too high or low. Wait until the print head cools or warms and the printer resumes printing automatically. ❏ Make sure that the roll paper cover is properly closed. ❏ Types A and B: The autocutter blade is not in the normal position and the autocutter is locked up. If it is a simple lock-up, the error is corrected automatically. If not, see the instructions below to return the blade to the normal position manually.
English EPSON Ecology Label This product is in compliance with the EPSON ecology label requirements. Please see the following link for detailed information on label criteria. (http://www.epson.co.
