SXT-4080 CDMA 1XRTT FIXED WIRELESS TERMINAL 800 MHz CDMA TECHNICAL MANUAL VOICE COMMUNICATION and PCO/PTB Application CDMA FWT SXT-2180 1 Technical Manual
Before installing your SXT-4080, carefully remove the contents from the shipping carton and check for evidence of shipping damage. If damage is found, contact your Authorized Epivalley Distributor or shipping agent immediately. SAFE OPERATION INSTRUCTIONS IMPORTANT! Before installing or operating this product, read the SAFETY AND GENERAL INFORMATION section of this guide. 9 Install the unit indoors. 9 Install the unit on a hard, flat surface for proper ventilation.
Emergency Battery Backup Checking the Battery Each Subscriber SXT-4080 unit comes with a standard internal battery inside, and can be replaced at your local After-Service Centers. Plug in Your Telephone 1) Locate the modular line port on your telephone and plug in one end of a standard phone cord 2) Connect the other end of the phone cord to the telephone port on the side of the Unit. NOTE: The SXT-4080 does not support direct computer modem (data) operation through the phone port or fax port.
Basic Operation Placing a Call 1) Pick up the handset and listen for a dial tone. 2) Dial the phone number. Receiving a Call When your telephone rings, pick up the handset and begin talking. NOTE: If you hear an incoming call while picking up the handset, you can receive the call by hanging up (placing the handset on the cradle) immediately. This will cause the phone to start ringing. Ending a Call Hang up the phone (place the handset onto the cradle).
Ⅱ. Hidden Menu *Note: User MUST input the security lock code when accessing below menu options. Emergency ‘##01’ - In the Emergency Menu state, you can store 3-address. - Press 1~3 key to select an address slot, and then wait until you have heard a security tone. It likes as short melody. - Enter the security lock code, and press desired Emergency Number and then press ‘À’ to save. - If you press ‘#’ to release. Ex) ‘##011911*’ – Store number ‘911’ to 1st Emergency Slot.
Ⅲ. Ring / Sound Menu Ring Type ‘##11’ - There are 9-ring types. - When you entered this menu, you can select ‘1~9’. After select one, press ‘À’ to store ring type. - If you choose ‘0’ key instead of ‘À’, It will be canceled. - If you press ‘#’ to release. Ex) ##11+0: Just cancel. It will make a terminal to idle status. ##11+1 Î assigned ring tone Î À : Index 1’s ring tone will be selected. Volume Type ‘##12’ - In the volume menu, you can contrast ring volume. - Press ‘1’ to up, and press ‘2’ to down.
Ⅳ. Tools Menu Caller ID ‘##21’ - In the Caller ID menu, you can select a CID type for your phone type. - There are 3-types of caller ID. - After choose one of them and press ‘À’, the item will be stored. - If you don’t want to set a caller ID, press ‘#’, then release. 1. BELLCORE 2. V.23 3. DTMF 4. None CID (same as ‘#’key) Dial Tone ‘##22’ - In the Dial tone menu, you can select a dial tone for your country. - There are 6-types of dial tone type for each country. - Press ‘À’ to set.
Ⅴ. Time Menu Alarm ‘##31’ - In the alarm menu, you can set a alarm time that you want. - Enter 4-digits for alarm time as ‘HH-MM’ type. - If you want to set a alarm time, press ‘À’. - When you press ‘#’, the alarm time will be released. Auto send time ‘##32’ - In the Auto send time menu, you can contrast an auto send time. - There are 10-types. (1sec~10sec) - When you choose a time, press ‘À’ to set.
ⅤI. Setting Menu New Code ‘##41’ - You can change a lock code which is being ‘0000’ as default value. - After enter a command of ‘##41’, you can heard a lock code sound immediately. - At this time, You should enter the current lock code to get an authority to change a lock code. - If the entered current lock code is right, a confirmation tone will be heard. - After then, You can try to enter new lock code. The processes of an entering new lock code have two steps.
SUPPLEMENTARY FEATURES (NETWORK DEPENDENT) Call Waiting The feature of call waiting enables you to get an incoming call while you are in a call conversation. You have an option of responding to the second call while putting the first call on hold. You can also disable the call waiting option during a particular call. Contact your service provider to activate call waiting. Three-Way Calling Three-Way Calling enables you to set up a three-way conversation with two other different-numbered users.
SXT-4080 TECHNICIAN PROGRAMMING Technician Programming Commands CDMA WIRELESS LOCAL LOOP 1X TERMINAL SERVICE MANUAL (SXT-4080) I. 1. 2. 3. II. Entering service mode(NAM mode) Pick up the handset. Press “*748#96*75259#”, then you can hear a confirmation tone. Press “000000”(security code), then you can hear a confirmation tone. Now, you are in a service mode. Current state is the main state. If you press wrong code, you can hear an alert tone. And then you will be in idle state.
go to main state.
Home NID6(12) “030712” Home SID7(13) “030713” Home NID7(14) “030714” Home SID8(15) “030715” Home NID8(16) “030716” Home SID9(17) “030717” Home NID9(18) “030718” Home SID10(19) “030719” Home NID10(20) “030720” Home SID11(21) “030721” Home NID11(22) “030722” Home SID12(23) “030723” Home NID12(24) “030724” Home SID13(25) “030725” Home NID13(26) “030726” Home SID14(27) “030727” Home NID14(28) “030728” Home SID15(29) “030729” Home NID15(30) “030730” Home SID16(31) “030731”
LOCK Home SID4(07) “030807” LOCK Home NID4(08) “030808” LOCK Home SID5(09) “030809” LOCK Home NID5(10) “030810” LOCK Home SID6(11) “030811” LOCK Home NID6(12) “030812” LOCK Home SID7(13) “030813” LOCK Home NID7(14) “030814” LOCK Home SID8(15) “030815” LOCK Home NID8(16) “030816” LOCK Home SID9(17) “030817” LOCK Home NID9(18) “030818” LOCK Home SID10(19) “030819” LOCK Home NID10(20) “030820” LOCK Home SID11(21) “030821” LOCK Home NID11(22) “030822” LOCK Home SID12(23) “030823
Press 2: B only Press 3:Home only Press 4:Home preferred Press À : go to main state after save. Press # : go to main state. Edit as “1”~”2” Press 1: enable Press 2: disable “0310” PRL ENABLE(10) Press À : go to main state after save. Press # : go to main state. Edit as “1”~”2” Press 1: enable Press 2: disable “0311” OTAPA ENABLE(11) Press À : go to main state after save. Press # : go to main state.
SXT-4080 TROUBLESHOOTING Telephone service is not working. If the telephone service is not working, first time, check an operation of the telephone equipment and wiring connected to your SXT-4080. Test the equipment on a different service or piece of equipment to ensure proper operation, or connect a known good telephone device to the phone port on the SXT-4080 unit.
FCC (Federal Communications Commission) Caution The R2NSXT-4080 has been tested for compliance FCC RF exposure limits. The R2NSXT-4080 should not be used with external antennas that are not approved for use with this device. Use of this in any other configuration may exceed the FCC RF exposure compliance limits. A separation between the user's body and the antenna shall be at least 20cm. WARNING! Read this information before use This equipment may generate or use radio frequency energy.
Temperature Environment Operating Temperature: From -20°C to +60°C ; Up to 95% relative humidity (non-condensing). Storage Temperature: From -25°C to +75°C; Up to 95% relative humidity (non-condensing). Antenna Care and Replacement Do not use the SXT-4080 with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Have your antenna replaced by a qualified technician immediately. Use only a manufacturer-approved antenna.
