SIT SXT-2080 Fixed Wireless Terminal SXT-2080 CDMA 1XRTT FIXED WIRELESS TERMINAL 800 MHz CDMA User Guide VOICE COMMUNICATION and PCO/PTB Application CDMA FWT SXT-2080 Rev.01.2.SM.SC.11.09.
SIT SXT-2080 Fixed Wireless Terminal Before installing your SXT-2080, carefully remove the contents from the shipping carton and check for evidence of shipping damage. If damage is found, contact your Authorized Sungil Distributor or shipping agent immediately. SAFE OPERATION INSTRUCTIONS IMPORTANT! Before installing or operating this product, read the SAFETY AND GENERAL INFORMATION section of this guide. 9 Install the unit indoors. 9 Install the unit on a hard, flat surface for proper ventilation.
SIT SXT-2080 Fixed Wireless Terminal Emergency Battery Backup Checking the Battery Each Subscriber Unit Terminal comes with a standard internal battery inside, and can be replaced at your local After-Service Centers. Plug in Your Telephone 1) Locate the modular line port on your telephone and plug in one end of a standard phone cord 2) Connect the other end of the phone cord to the telephone port on the side of the Unit.
SIT SXT-2080 Fixed Wireless Terminal Basic Phone Operation Placing a Call 1) Pick up the handactivate and listen for a dial tone. 2) Dial the phone number. Receiving a Call When your telephone rings, pick up the handactivate and begin talking. NOTE: If you hear an incoming call while picking up the handactivate, you can receive the call by hanging up (placing the handactivate on the cradle) immediately. This will cause the phone to start ringing.
SIT SXT-2080 Fixed Wireless Terminal Ⅱ. Ring / Sound Menu Ring Type ‘##11’ - In the Ring type menu, you can select 9-way ring type. - Select ‘1~9’ and press ‘À’ to store ring type. - If you choose zero ‘0’ instead of ‘À’, It will be canceled. - If you press ‘#’ to deactivate. Ex) ##11+0: Canceled what you did. it will make a terminal idle. ##11+1 Î assigned ring tone Î À : Index 1’s ring tone will be selected. Volume Type ‘##12’ - In the Volume menu, you can control FWT ring volume.
SIT SXT-2080 Fixed Wireless Terminal Ⅲ. Tools Menu Caller ID ‘##21’ - In the Caller ID menu, you can select CID type for your phone type. - There are 3-types of caller ID. Please select one of the following and press ‘À’to activate. - If you want to deactivate the caller ID feature, press ‘#’. 1. BELLCORE 2. V.23 3. DTMF 4. None CID (same as ‘#’key) Dial Tone ‘##22’ - In the Dial tone menu, you can select dial tone for your country.
SIT SXT-2080 Fixed Wireless Terminal Flash time ‘##33’ - In the Flash time menu, you can determine flash time in the range of 50~800 ms. - If the designated flash time exceeds 800 ms, then such inputs will be ignored. - Press ‘À’ to activate. Or press ‘#’ to deactivate. Ex) ##3 + 300 + À : to activate a flash time to 300 ms Flash time ‘##33’ - In the Flash time menu, you can change flash time from 50 to 999 ms.(default : 100 ms ) - If entered time is out of ranges, it will be ignored.
SIT SXT-2080 Fixed Wireless Terminal Voice privacy ‘##44’ - You can activate the option of Voice privacy to protect your voice from being tapped. But It is possible only if the operator supports this feature.. - You can change the option by doing follows. - Press ‘À’ for changing a current value to ‘Standard’ option - Press ‘#’ for changing a current value to ‘Enhanced’ option.
SIT SXT-2080 Fixed Wireless Terminal Unable to Receive Incoming Calls If more than one telephone or telephone device is connected to your SXT-2080, make sure that all devices are “on-hook” (hung up). If one extension is “off-hook” (off its cradle), none of the extensions on your phone line will ring when an incoming call occurs. Moisture or Ventilation Problems Visually inspect your SXT-2080’s unit enclosure. Moisture can damage the equipment. Ventilation is also very important.
SIT SXT-2080 Fixed Wireless Terminal while the vehicle is in motion. Always obey the law. Exposure to electronic Devices Most modern electronic equipment is shielded from RF energy. However, RF energy from cellular devices may affect inadequately shielded electronic equipment. RF energy may affect improperly installed or inadequately shielded electronic operating and entertainment systems in motor vehicles.
SIT SXT-2080 Fixed Wireless Terminal Regulatory Information FCC compliance Information This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received. Including interference that may cause undesired operation. Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules.
