Home Roam TV TM Thank you for purchasing this product. For your safety and best performance, please read this instruction before first use, and keep this manual for future reference. In case that you have any further questions after reading this manual, please contact Customer Service at 1-866-709-1999 or email to service@envizendigital.
Table of Contents 1. Safety Disclaimer........................................................................................................1 2. Introduction.................................................................................................................3 3. Features.......................................................................................................................3 4. What’s in the Box.....................................................................................
Safety Disclaimer To prevent electric shock or fire hazard do not expose the unit to rain or moisture. Warning To avoid electric shock or fire hazard,do not open the cabinet,refer servicing to qualified person only. This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Safety Disclaimer Do not use power-line operated sets near water-for example,near a bathtub, washbowl,kitchen sink,or laundry tub, in a wet basement,or near a swimming pool,etc. copyrights: the copyright protected content cannot be copied.broadcasted,screened,cable casted,played publicly and rented, unless it is authorized. Unplug the unit and refer servicing to qualified service personnel under the following conditions: E.If the unit has fallen or the cabinet has been damaged. F.
Introduction Congratulations on the purchase of your Envizen Digital Home Roam TV. Home Roam TV allows you to view any source device connected to the transmitter module on the 7” LCD Display Receiver anywhere in your home, up to 100 Foot range. You may connect up to two source devices (Cable / Dish set top box, TV, DVD, Blu-ray, VCR or Media Player) to Home Roam TV. (Two sets of cables are supplied) Note: Home Roam TV has been tested in excess of 100 foot.
Unit Functions 5.1 Transmitter Module 1 2 4 3 5 6 1.ANT: 2.4G wireless audio/video signal antenna. 2.TV IN: R/L/CVBs input, from TV, Cable or Dish set top box. 3.TV OUT: R/L/CVBs output to TV set. 4.AV: AV combination input jack. 5.POWER: Connect 9V/1A DC power. 6.ON/OFF: Turn on/off the Transmitter Module. 5.2 Display Receiver 13 1 8 2 3 9 4 5 10 6 11 7 12 1.TV: Switch to TV/Cable or Dish Set Top Box. 2. : Adjust Brightness/Contrast/Saturation under Menu setup. 3.
Setting up Home Roam TV View any source connected to the transmitter module as an extension of the electronic device: Cable / set top box, TV, Blu-Ray player, DVD player, VCR or Media player. In this mode, you can operate the Receiver by powering on/off, menu setup,volume controls and switching different channels on the Home Roam TV Display Receiver. 6-1.
Setting up Home Roam TV Pass-through to a TV set: CONNECT HOME ROAM TV TRANSMITTER MODULE [TV OUT] TO A LOCALLY CONNECTED TV SET TO PASS THROUGH ANY PROGRAM SOURCE CONNECTED TO [TV IN]. NOTE: Not required if cable Set Top Box is connected to TV via HDMI. 6-2. HR TV Transmitter Module Operation POWER UP HOME ROAM TV TRANSMITER MODULE 1.Plug in the AC/DC adapter to the Transmitter Module and a power outlet and press the button “ON”. IMPORTANT: The Home Roam power adapter is only for use with Home Roam.
Setting up Home Roam TV the battery be charged for 3 hours with the power off; While the battery needs to be charged continuously for 8 hours if the Display Receiver is in use. 3.The battery life inside the receiver supports up to 2 hours usage without the adapter connected. 4.When the Receiver unit is switched off – (a) A Red LED light indicates battery is being charged while the Receiver is not in use; (b) LED light will be turned off whenever the battery is fully charged. 5.
Setting up Home Roam TV 6-5. Menu Setup on Display Receiver Press [MENU] key on the display receiver panel to go into the Menu Setup interface. The Receiver screen will now display the following content. The users can select Brightness/Contrast/Saturation through and keys as what you like, then select the appropriate values through and keys according to the circumstances. Demo Playback The display receiver also includes a 60 seconds video clip about the introduction of Home Roam TV .
Setting up Home Roam TV Reset to Factory Default The values have been set under an appropriate level before leaving factory, but if the users adjust the values at an undesirable status, shown as below picture, the users can reset the values to factory default. Press and keys to select [Reset to factory default], then press just like below picture: or keys to set it OK, NOTE: Please exit the Menu setup first, then adjust the receiver volume up and down.
Troubleshooting A. Blue Screen is displayed with only audio coming through 1.Press the button on the Display Receiver to select the corresponding source connected to the Transmitter Module 2.Verify video connections to both Transmitter Module and Display Receiver are matched; 3.The A/V connection cable between Source Device and the Transmitter Module unit is completely inserted into the socket at both ends; 4.Verify the quality of the A/V cable by switching to a different A/V cable; 5.
Appendix ● PAIRING THE TRANSMATTER MODULE AND DISPLAY RECEIVER Home Roam TV is shipped from the factory already paired between the transmitter and the Home Roam Display. Should the pairing ever be disrupted, you will not receive any video or audio on the display. STEP 1: TURN ON BOTH UNITS Make sure both the Transmitter Module and the Display Receiver are properly powered and turned on.
Appendix STEP 4: COMPLETION OF THE PAIRING SEQUENCE You may now operate the units normally. Tip: During the pairing process, do not depress the pairing button more then 15 seconds. Tip: During the pairing process, do not turn off either unit or lose power. ● Quick Setup Reference 1.VCR 2.Media Player 3.
Warranty Warranty Terms and Conditions Envizen Digital (“Envizen”) warrants your Envizen products against defects in material and workman ship during the warranty period from the original date of purchase, subject to the following terms and conditions.
the original package, with the complete set of accessories. 3. Upon receiving the product, depending on the condition of the defects, Envizen will repair or replace product, and ship it back to the customer within 2-4 weeks. 4. For additional information, please contact Envizen Customer Service. Out of Warranty Repair For additional information on obtaining an extended warranty service, contact Envizen Customer Service Department by e-mailing service@envizendigital.com or call 1-866-709-1999.
