Operating instructions

ManualsBrandsEnvision ManualsLED displaysG917w

Downloaded from ManualMonitor.com Manuals

Summary of content (22 pages)

PAGE 1
Downloaded from ManualMonitor.
PAGE 2
TABLE OF CONTENTS FOR YOUR SAFETY ------------------------------------------------ 1 SAFETY PRECAUTIONS-------------------------------------- 2 SPECIAL NOTES ON LCD MONITORS ----------------- 3 BEFORE YOU OPERATE THE MONITOR---------------------- 3 FEATURES ------------------------------------------------------- 3 PACKING LIST --------------------------------------------------- 3 INSTALLATION INSTRUCTIONS --------------------------- 4 CONTROLS AND CONNECTORS ------------------------- 5 ADJUSTING THE
PAGE 3
Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
PRECAUTIONS  Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.  Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
PAGE 5
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • You may find slightly uneven brightness on the screen depending on the desktop pattern you use. • The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.
PAGE 6
INSTALLATION INSTRUCTIONS Install Remove Figure 1 Installing and Removing the Base 5 Downloaded from ManualMonitor.
PAGE 7
POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required). 3. Connect the AC-power cord into your LCD monitor’s AC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor.
PAGE 8
ADJUSTING THE VIEWING ANGLE • • • For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -5° to 20°. Figure 3 NOTES • • Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
PAGE 9
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • Press the power button to turn on the monitor position. The power indicator will light up.
PAGE 10
FRONT PANEL CONTROL • Power / Menu : Press the Menu (Power) button to activate the OSD window. Press left, right, up, down button to navigate through the functions. Once the desired function is highlighted, press the Menu (Power) button to activate sub-menu . • Contrast /Left: When there is no OSD , press Contrast ( ) to active Contrast adjustment bar, press ( )or ( ) to adjust Contrast. • DCR/Right: Press DCR key continuously to active or disable DCR function when there is no OSD.
PAGE 11
NOTES • Do not install the monitor in a location near heat sources such as radiators or • • • • air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory.
PAGE 12
HOW TO ADJUST A SETTING 1. 2. 3. 4. 5. Press the Menu (Power) button to activate the OSD window. Press left, right, up, down button to navigate through the functions. Once the desired function is highlighted, press the Menu (Power) button to activate submenu . In sub-menu, Press up, down button to navigate through the functions. Once the desired function is highlighted, press , button to button to change the setting. Press Menu (Power) button to return to superior menu.
PAGE 13
ADJUSTING THE PICTURE Function Control Illustration Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Icon Description Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digitalregister.
PAGE 14
Color Temp. 0-100 Warm 6500K Normal 7300K Recall Normal Color Temperature from EEPROM. Cool 9300K Recall Cool Color Temperature from EEPROM. Recall SRGB Color Temperature from EEPROM. sRGB Red User Green Blue Color Boost Picture Boost Full Enhance on or off Nature Skin on or off Green Field on or off Sky-blue on or off AutoDetect on or off Demo on or off Red Gain from Digitalregister Green Gain Digitalregister.
PAGE 15
V.Position 0-100 Adjust the vertical position of OSD Timeout 5-120 Adjust the OSD Timeout Transparence 0-100 Adjust the transparence of OSD Select the OSD language Language Auto Input Select DVI D-SUB Extra Auto Config yes or no Image Ratio wide or 4:3 DDC/CI yes or no Information Reset Reset Exit Exit yes or no 14 Downloaded from ManualMonitor.
PAGE 16
PLUG AND PLAY PLUG & PLAY DDC2B FEATURE This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request EDID information over the DDC2B channel.
PAGE 17
TECHNICAL SUPPORT (FAQ) Problem & Question Power LED is not on No Plug & Play Picture is fuzzy Possible Solution *Check if the Power Switch is in the ON position *Power Cord should be connected *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Adjust the Contrast and Brightness Controls.
PAGE 18
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizontal disturbances in light picture. For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down mode pattern. ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. 2.
PAGE 19
APPENDIX SPECIFICATIONS Driving system Size Pixel pitch LCD Panel TFT Color LCD 481 mm diagoanl 0.2835mm(H) × 0.2835mm(V) R,G,B Analog Interface Video Digital Input Separate Sync. H-Frequency V-Frequency H/V TTL 30kHz – 83kHz 56Hz-75Hz 135MHz 1440X900@60Hz VESA DDC2B CI ON Mode ＜37W ＜2W Dot Clock Max. Resolution Plug & Play Power Consumption OFF Mode D-Sub 15pin Input Connector DVI-D 24pin Input Video Signal Analog:0.
PAGE 20
External Controls: Switch Functions Power Consumption ( Maximum ) Regulatory Compliance  Eco Mode /Up  Contrast /Left  DCR/Right  Source(Auto) /Exit  Power / Menu  Luminance  Image Setup  Color Temp.  Color Boost  Picture Boost  OSD Setup  Extra  Reset  Exit 37Watts CE,CB,RoHS,EPA 19 Downloaded from ManualMonitor.
PAGE 21
Preset Display Modes STAND RESOLUTION HORIZONTAL VERTICAL FREQUENCY(KHz) DOS-MODE VGA SVGA XGA SXGA WXGA FREQUENCY(Hz) 720 × 400 31.47 70.0 640 × 480 31.47 60.0 640 × 480 37.50 75.0 800 × 600 37.879 60.0 800 × 600 46.875 75.0 1024 × 768 48.363 60.0 1024 × 768 56.476 1024 × 768 60.021 75.0 70.0 1280 × 1024 64.00 60.0 1280 × 1024 80.00 75.0 1440 × 900 55.935 59.8 CONNECTOR PIN ASSIGNMENT 1 5 6 10 11 15 15 - Pin Color Display Signal Cable PIN NO. 1. 2. 3. 4. 5.
PAGE 22
24 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. 1. 2. TMDS Data 2TMDS Data 2+ TMDS Data 2/4 Shield 13. 14. TMDS Data 4-/N.C. TMDS Data 4+/N.C. DDC Clock DDC Data Analogue Vertical Sync /N.C. TMDS Data 1TMDS Data 1+ TMDS Data 1/3 Shield TMDS Data 3-/N.C. 16. 17. 18. 19. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 15. 20. 21. 22. 23. 24. 21 Downloaded from ManualMonitor.com Manuals DESCRIPTION TMDS Data 3+/N.C. +5V Power GND(return for +5V hsync.