EN9410e 19” TFT LCD Monitor User’s Manual By Envision Peripherals Inc. www.ENVISIONdisplay.
FOR YOUR SAFETY Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PRECAUTIONS: Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
circuit parts causing a fire or electric shock. Never spill liquids on the monitor. Do not attempt to service the monitor by yourself. Opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel. Do not pull or bend the power cable and signal cable or place the monitor or any heavy objects on the cables. If the cables are damaged, they may cause fire or electric shock.
GENERAL NOTES The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. You may find slightly uneven brightness on the screen depending on the desktop pattern you use.
OTHER NOTES The screen surface is very soft. Do not rub, touch or tap the screen surface with sharp object such as pen or pencil. This contact may scratch or damage the screen. These damages are not covered under the warranty. Turn your computer OFF before installing your new monitor. Refer to your computer manual for the proper shut down procedure. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor.
Disclaimer Envision Peripherals Inc. makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, Envision Peripherals Inc. reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.
Table of Contents 1 Important Safety Instructions..........................................1 2 Features.............................................................................2 3 Unpacking the Monitor.....................................................3 Installation and Removal of the Base…………………….3 4 Hardware Installation........................................................4 5 Windows driver installation .............................................5 6 Setting the Display Resolution...............
1 Important Safety Instructions Please read the following safety instructions before installing or cleaning your Envision monitor: 1. Unplug the monitor’s power cable from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a soft cloth to clean the monitor housing. 2. Slots and openings on the back or top of the cabinet are provided for ventilation. They must not be blocked or covered.
2 Features Your Envision EN9410e Monitor features: SXGA (1280 x 1024 pixel) Resolution LCD Panel True Colour Display With FRC support for 16.7M colours, the Envision EN9410e monitor offers you better image quality. High Quality Expansion With any resolution within the monitor’s specified range, your Envision EN9410e monitor can expand the image to full screen. Auto Adjustment Function The auto-adjustment key automatically optimises the image.
3 Unpacking the Monitor Please check that the following items are included with your monitor. If they are missing or damaged, please contact your place of purchase immediately. Monitor 1 pc Signal Cable 1 pc Power Cable 1 pc QSG (Quick Start Guide) Installation and Removal of the Base 1. Installation 2.
4 Hardware Installation Your monitor is equipped with an automatic power supply with a voltage range from 100 to 240 Volts AC at a frequency of 50 to 60 Hz. Make sure that your local power supply is within the supported range. If you are unsure, please contact your electricity supplier. To install your Envision EN9410e monitor: 1. Make sure that the power to the computer and the power to the monitor are both turned off. 2.
5 Windows driver Installation The Envision EN9410e is fully Windows compatible so no specific windows drivers are required to be loaded. Windows 98, ME, and 2000 The first time you start Windows after connecting your new monitor, the system will detect the monitor and automatically start the Add New Hardware wizard. Just follow the prompts to load the native Plug and Play drivers.
6 Setting the Display Resolution Choosing The Best Resolution All Liquid Crystal Displays (LCDs) have a fixed resolution that is the same as the maximum resolution that may be displayed on the LCD. In the case of the EN9410e the LCD resolution is 1280 x 1024 pixels. This is also known as the “native” resolution of the monitor. Lower resolutions can be displayed at full screen through an interpolation circuit.
Supported Graphics Modes and Refresh Rate Selection There is no need to choose the highest possible refresh rate when using an LCD monitor. It is not technically possible for an LCD monitor to flicker. Even at a refresh rate of 60 Hz you will get an absolutely flicker-free image. For best results, it is important that you set the graphics adaptor to use one of the monitor’s preset display modes shown in Table 1 on the next page. Other graphics signals may be displayed poorly or not at all.
caused by the signal from the VGA card if it does not correspond with the usual standard. This is not however, a problem with the monitor. If it is still visible after using the Automatic adjustment, you can usually improve the displayed image by manually adjusting the phase, horizontal position and pixel frequency settings using the "Geometry" menu. See Chapter 7, Adjusting the Monitor, for more details. When you shut Windows down you may see interference lines on your screen.
7 Adjusting the Monitor Picture Optimisation The easiest way to obtain an optimal picture is by using the Auto button for 2 seconds. This only works reliably if the graphics adaptor is set to use one of the monitor’s factory modes (see Table 1 in the previous chapter) and if you are displaying a suitable stationary image (such as the windows desktop). The monitor will remember the settings obtained by the auto calibration settings and use them whenever you turn the monitor on.
(from left to right) Menu Enter OSD menu. Enter submenus or select items within OSD menu. Move the selection cursor upwards within the OSD menu. Move the selection cursor downwards within the OSD menu. Adjust OSD functions. (Decrease) Adjust OSD functions. (Increase) SELECT Automatically adjust the vertical, horizontal position, pixel /AUTO phase and pixel clock. Exit OSD menu/submenus.
Tracking Adjustment CLOCK: Adjust to minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE: Adjust to remove any horizontal distortion, and clear or sharpen the image of characters. Position Adjustment V-Position: Adjust the vertical position of the picture. H-Position: Adjust the horizontal position of the picture.
Color Adjustment There are three items for color adjustment: 9300K: Bluish white 6500K: Reddish white User defined: Red, Green, Blue. Adjust to set your own color level. Other LANGUAGE: Multi- Language selection OSD POSITION: Adjust the OSD window position on the screen. INFORMATION: “ON” When changing screen resolution setting( for example: horizontal/ vertical refresh rate), display information is briefly shown on the screen and vice versa.
8 Frequently Asked Questions The image is blurred, how can I get the best quality picture? Read chapter 6, Setting the Display Resolution, and select a graphics signal with the correct resolution and refresh rate. Then read chapter 7, Adjusting the Monitor, and make adjustments to the displayed image based on these instructions. Have you used a VGA extension cable? If so, remove the extension cable and check the displayed image.
No image is displayed, what can I do? Check that the light (LED) next to the monitor’s power button is lit and is green in colour. If the LED is green, press the MENU button on the monitor to access the On Screen Display. If the message NON PRESET MODE appears there, please read chapter 6, Setting the Display Resolution and reset the graphics card to one of the monitor’s supported graphics signals. If the LED is orange the monitor is in power saving mode.
The display shows OUT OF FREQUENCY error message: Read chapter 6, Setting the Display Resolution, and select a graphics signal with the correct resolution and refresh rate.
9 Specifications Model: Envision EN9410e Display Characteristics Display Type 19“ active matrix Thin Film Transistor Liquid Crystal Display Viewable Diagonal Area 43.3 cm / 19” Native (Maximum) Resolution 1,280 x 1,024 pixels Colors 16.7 million (6bpp+dithering) Dot Pitch 0.294 mm User Interface Controls Mains power switch, Automatic image adjustment, 6 OSD buttons On-Screen Display Functions Contrast, Brightness, Vert. & Hor.
Signal Connection 15-pin mini D-sub cable Physical Characteristics Power Management Energy Star Maximum Power Consumption 50 Watts Power Saving Mode < 1 Watts Operating Voltage Automatic switched mode power supply, 100 - 240 V, 50 - 60 Hz Dimensions (W x H x D) 426 x 435 x 214mm Weight 4.
