EFT720 17” Flat CRT User’s Manual By Envision Peripherals, Inc. www.ENVISIONdisplay.
Thank you very much for choosing the Envision Color Monitor. We recommend that you take a few minutes to read carefully through this brief but comprehensive manual before installing and switching on the monitor. Please keep this manual in a safe place for your future reference. Plug & Play Drivers for the Envision Series Monitors are available at: www.ENVISIONdisplay.com CHECKING THE CONTENTS OF THE MONITOR PACKAGE The product package should include the following items: 1. Monitor 2. Owner's Manual 3.
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PRECAUTIONS ! Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. ! Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.
Plug & Play DDC1/2B Feature This monitor is equipped with VESA DDC1/2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The communication channel is defined in two levels, DDC1 and DDC2B. The DDC1 is a unidirectional data channel from the display to the host that continuously transmits EDID information.
TECHNICAL SUPPORT(FAQ) Power LED is not on *Power Cord should be connected No Plug & Play *Check if the PC System is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Check if the D-15 plug pin of Video Cable is bent *Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at: www.ENVISIONdisplay.com) Picture is fuzzy *Adjust the Contrast and Brightness Controls.
INSTALLATION INSTRUCTIONS SWIVEL BASE To attach the swivel base to the monitor, do the following: • Carefully turn the monitor on its side or upside down. (see figure 1) • Locate the cavities at the bottom front of the monitor. • Insert the pegs on the swivel base into these cavities. Push the swivel base forward until the swivel base locks in place. • To remove the swivel base, hold the bottom of the swivel base, then push it out. POWER CORD Power Source: 1.
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be connected. • Connect the video cable from the monitor to the video card. • To turn the monitor on, press the power switch to ON position. The power indicator will light up.
Figure 1: Installing and Removing the Swivel Base Figure 2: Connecting Cables 1. 2. 3. Signal Cable Power Cord AC Outlet 1. 2. 3. 4. 5. 6.
FRONT PANEL CONTROL (see figure 3) NT PANEL CONTROL • Power ON/OFF Switch: Press this key to switch the display ON or OFF. • Power Indicator : Green — Power On mode. Orange — Off mode. • • MENU : Press this key to either bring up the OSD menu or select an item on the menu. Contrast: With the OSD menu on, press this key to either select a function or to adjust up the value of a selected function. With the OSD menu off, press this key to adjust the contrast.
ADJUSTING THE PICTURE (see figure 4) 1. CONTRAST Adjust the picture contrast. 2. BRIGHTNESS Adjust the picture brightness. 3. H- CENTER Adjust the horizontal position of the picture. 4. H- SIZE Adjust the picture’s horizontal size. 5. V- CENTER Adjust the vertical position of the picture. 6. V- SIZE Adjust the picture’s vertical size. 7. ZOOM Adjust the picture’s horizontal and vertical size simultaneously. 8. PINCUSHION Adjust the pincushion and barrel. 9.
17. RECALL Press RECALL to restore the monitor to factory settings. 18. EXIT Close OSD window. 19. SELECT LANGUAGE Select the language as you like.
SPECIFICATION CRT Viewable Image Size Video Separate Sync. H/V-sync.: Scanning Frequency: Horizontal Vertical Max. Resolution Video Dot Rate Factory Preset Timings : User mode Timings : Power Source Operating Humidity Dimension Weight Signal Cable Plug & Play EPA On ENERGY mode Off STAR® mode Power consumption Preset display area Regulations 43.2cm(17"), 90º deflection, 29mm neck, 21mm(H), 0.25mm(D) dot pitch 40.6cm (16"), diagonal 0.
Preset Timing Table 720 x 400 HORIZONTAL FREQUENCY 31.5kHz VERTICAL FREQUENCY 70Hz VGA 640 x 480 31.5kHz 60Hz VESA/85 640 x 480 43.3kHz 85Hz VESA/85 800 x 600 53.7kHz 85Hz VESA/85 1024 x 768 68.7kHz 85Hz VESA/60 1280 x 1024 64.0kHz 60Hz STANDARD RESOLUTION IBM Connector Pin Assignment 1 5 6 10 11 15 PIN NO. DESCRIPTIO N 1. 2. 3. Video-Red Video-Green Video-Blue BLANK 4. 5. 6. 7. 8. PIN NO. NO. de Terminal PIN NO. 9. 10. 11. 12. SENSES GND-R GND-G GND-B 13. 14. 15.
