Owner's manual

6
www.ewswater.com O: 702.256.8182; M-F 8:30am-4:30pm PST E: [e-mail]
Step 1
This system may have come with sample plugs. If so, please remove correctly by following instructions below before installation.
WARNING: NEVER ATTEMPT TO REMOVE TUBING OR SAMPLE PLUGS BY JUST PULLING. Follow simple instructions
illustrated below to remove properly.
INSPECT: Inspect the tting for any damage from shipping, handling and/or delivery. STOP, if collet is damaged in any way;
call, fax or e-mail customer service for a replacement tting.
Step 2 Making the Connections from Inlet/Supply Connection to Unit and from Unit to the dispenser or other device being supplied.
Firmly insert the tubing completely into the tting. You may feel a resistance at the o-rings when you insert the tubing.
Step 2a Connect the orange/red tubing from the installed Inlet/Supply Connection into the left side of the unit. This is the raw supply
water into the unit. Insert and press the tubing rmly and completely into the tting.
Step 2b Connect the blue tubing from the right of the unit. This is the ltered water line. Insert and press the tubing rmly and com-
pletely into the tting.Now connect that blue tubing to the dispenser or other device(s) chosen to get ltered water.
NOTE: EWS does not provide a dispenser with the Model No. SS Single-Stage unit. Can be purchased separately.
WARNING: Water ow is one direction. Make sure never to reverse directions.
Never Pull Tube Out To
Remove
Push Collet In To Release
To Insert, Press Tubing In
Firmly and Completely
Make sure tubing end is
straight and not attened
Connection of Tubing from Supply and to a Dispenser or Other Device(s)
CAUTION: Always leave the tubing provided to allow lifting the unit for lter replacement and maintenance.Make sure tub
ing has gentle curves. Roll and secure as needed. Do not bend or kink tubing. We do not recommend shorten-
ing the tubing, however, If needed, at end, cut tube straight and do not atten. Avoid any tubing contact to hot water
line.
WARNING: NEVER ATTEMPT TO REMOVE TUBING BY JUST PULLING. Follow simple instructions illustrated above to remove properly.
INSPECT: Upon installation, inspect the connection and give the tubing a gentle “tug” to insure proper connection and integrity of the
tting.
Inspect the tting for any damage from shipping, handling, delivery, and/or installation.
STOP, if collet is damaged in any way; call, fax or e-mail customer service for a replacement tting.
Test Integrity of Fitting:
Give a Gentle “Tug”
To Insure
Proper Connection
See All Cautions,
Warnings and
Inspections
Placement or Locating the Filtration Unit
Always assume for enough space and tubing to remove, move and/or adjust
for lter replacement and maintenance.
Mounting the unit to a wall, cabinet side or other vertical surface, a minimum clearance of 4” will be required to allow for lter replace-
ment. Please see the following procedures:
Step 1 The lter cartridge for the unit is included. Locate the lter cartridge.
Inserting the lter cartridge: At the blue top of lter cartridge nd the side with two (2) notches. Line the notches up and insert lter
cartridge into the lter head assembly. Once cartridge is fully inserted into the head turn clockwise and completely lock into position.
Step 2 Once lter system has been fully assembled, mark pilot holes using the bracket as a template.
Step 3 Using a drill bit or punch, drill a hole or punch as a starter hole to catch the mounting screws.
WARNING: ALTERNATIVE FASTENING METHOD MAY BE REQUIRED FOR PLASTER BOARD, PARTICLE BOARD OR SIMILAR
MATERIAL INSTALLATION. USE SAFETY GLASSES OR OTHER EYE PROTECTION TO PREVENT POSSIBLE EYE INJURY DUE
TO FLYING PARTICLES.
Step 4 Set mounting screws (provided) with screw driver. Leave a 1/4” gap between the screw head and mounting surface to allow
the bracket to slide on easily.
Step 5 Slide the bracket over screws and hang the unit. Make sure unit is level. Now make the connections of tubing to/from the
system.