M55C-FPI PELLET STOVE TECHNICAL MANUAL SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER. PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.
Table of Contents Safety Warnings & Recommendations...............................................................................................3 Specifications.................................................................................................................................5 Rating Label & Location............................................................................................................5 Dimensions............................................................................
Safety Warnings & Recommendations * This manual is designed for the technician in conjunction with the owner’s manual. * Please read this entire Technical Manual before installing or operating your Enviro Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Any unauthorized modification of the appliance or use of replacement parts not recommended by the manufacturer is prohibited.
Safety Warnings & Recommendations ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be grounded. The grounded electrical cord should be connected to a standard 110-120 volts (4.2 Amps), 60 hertz electrical outlet and also must be accessible. If this power cord should become damaged, a replacement power cord must be purchased from the manufacturer or a qualified Enviro dealer.
INSTALLED AS A FIREPLACE INSERT STOVE MODEL (FPI) / A INSTALLE COMME UN MODELE SUR PIED DE POELE. DO NOT REMOVE THIS LABEL / NE RETIREZ PAS CETTE ÉTIQUETTE J F M DATE OF MANUFACTURE / DATE DE FABRICATION: A M J J A S O N D 2010 2011 2012 Utilisation avec granules - le bois, le maïs, le blé, & l'orge seulement. Utiliser seulement lorsque les portes avants et la porte du réceptacle de cendre sont fermées. Si une ou des vitres devaient être remplacées, utilisez seulement du verre céramique.
Specifications Dimensions: 16 1/8" 24 3/4" 26 7/8" 12" 32 7/8" 23" 44" Figure 2: Dimensions of M55C-FPI. Specifications: Input rating when using: Wood Pellets/Corn - 55,000BTU (16.1KW•hr) & Wheat/Barley - 53,000BTU (15.5KW•hr). Table 1: M55C-FPI Specifications. Description Residential Pellet Heater Fuel type 6mm (¼”) dia. Pellets - wood, corn, wheat, & barley* Voltage 110 - 120 V Current 4.2 Amps Max Power 504 Watts Frequency 60 Hz Hopper Capacity up to 50 lb (22.7 Kg) Consumption on Low 1.
Installation Deciding Where to Locate your Pellet Appliance: 1. Unit must be installed in a masonry fireplace. 2. Do not install the stove in a bedroom or room where people sleep in. 3. Locate the stove in a large and open room that is centrally located in the house. This will optimize heat circulation. 4. Check clearances to combustibles and for the least amount of interference to house framing, plumbing, wiring, etc. 5. You can vent the stove with approved flex pipe. 6.
Installation NOTE: Installer must attach the metal “fireplace altered” tag using screws or nails to the fireplace, in a location readily visible should the fireplace insert be removed, if the fireplace has been modified to accomodate the M55C-FPI. Installing the Insert Frame & Levelling: Warning: Careless installation is the major cause of safety hazards. Check all local building and safety codes before installation of unit. 1. Mount Surround Panel to Insert Frame. 2.
Installation To Start Stove HIS LABEL / NE RETIREZ PAS CETTE ÉTIQUETTE grades of woo of pellets in th INSTALLED AS A FIREPLACE INSERT STOVE MODEL (FPI) / A INSTALLE To Operate S COMME UN MODELE SUR PIED DE POELE. MODE: (Req Minimum clearances to combustible materials./ Les dégagements minimums aux thermostat co matériels combustibles: close again. 5.5KW*hr) A Sidewall to center of unit (De la paroi au centre de l'unité) 24” (610 mm) automatically.
Installation Vent Termination Requirements: IT IS RECOMMENDED THAT YOUR PELLET STOVE BE INSTALLED BY AN AUTHORIZED DEALER/INSTALLER. Table 2: Use in conjunction with Figure 6 for allowable exterior vent termination locations. Letter Minimum Clearance A 24 in (61 cm) Description B 48 in (122 cm) Beside/below any door or window that may be opened. (18” (46 cm) if outside fresh air installed.) C 12 in (30 cm) Above any door or window that may be opened. (9” (23 cm) if outside fresh air installed.
Installation Outside Fresh-Air Connection: This Heater must have adequate air for proper combustion in the room that it is installed. A Fresh-air intake is strongly recommended for all installations. Failure to install intake air may result in improper combustion as well as the unit smoking during power failures. The inlet to the intake must be below and a minimum of 12” (30cm) away from the unit exhaust outlet.
Installation Masonry Fireplace Installation: A non-combustible manufactured hearth pad (min. 24 gauge galvanized steel or similar) must cover combustible flooring underneath, as well as 6” (150 mm) in front of the heater and 6” (150 mm) to the side of the heater. Rain Cap Steel Plate or Flashing Flexible or Rigid 4" Stainless Steel Liner Damper Removed or Fastened Open Flexible stainless steel pipe connection 12" (30.
Installation Positive Flue Connection without a Full Reline (USA Only): This unit does not require a full reline (in USA only) when installing into a masonry fireplace, however, it is recommended to ensure proper drafting of the appliance. IMPORTANT: Ensure the chimney and firebox are cleaned and free of all debris, including soot and ashes, before proceeding with this installation. If it is not clean soot maybe blown into the room through the unit’s blower.
Installation Built-In Installation: Installation without a masonry fireplace The M55C-FPI can be installed without an existing masonry fireplace by building an enclosure for the unit to be installed in. This enclosure must be a minimum of 18” deep, 36” wide and 23-1/4” high and made with ½” noncombustible cement board. The floor of the enclosure must consist of a minimum of 1-1/4” air space and a layer of ½” noncombustible cement board and a layer of tile.
Installation Horizontal Exhaust Through Wall Installation: Vent installation: install vent at clearances specified by the vent manufacturer. A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces, or a floor, or ceiling.
Installation RECOMMENDED - Through Wall With Vertical Rise and Horizontal Termination Installation: NOTE - This venting configuration is only for use with the Built-In installation. Termination cap 90°elbow Wall framing Vertical section of vent pipe Wall strap Horizontal frame for thimble Clean out tee Wall thimble Figure 12: Venting horizontally with rise.
Installation Outside Vertical Installations: To accomplish an outside vertical pipe installation, follow the “Horizontal Exhaust Through Wall Installations” section and then finish it by performing the following. 1. Install a tee with clean out on the outside of the house. 2. Install PL vent upward from the tee. Make sure that you install support brackets to keep the vent straight and secure. All joints in the exhaust venting system must be fastened with at least three (3) screws. 3.
Installation Inside Vertical Installations: 1. Install a tee or 90° elbow on the inside of the house. 2. Install PL vent upward from the tee. Make sure that you install support brackets to keep the vent straight and secure. All joints in the exhaust venting system must be fastened with at least three (3) screws. 3. Install ceiling thimble and secure the flashing as you go through the roof. 4. Ensure that the rain cap is approximately 24” (61 cm) above the roof.
Installation Slider/Damper Set-Up: This is used to regulate the airflow through the pellet stove. CONVECTION FAN EXHAUST CHANNEL EXHAUST SENSOR & REMOVABLE PLATE SLIDER DAMPER NOTE: THE SURROUND PANEL MOUNT WAS REMOVED FOR CLARITY Figure 15: Slider/Damper Plate & Rod in Unit. Figure 16: Efficient Flame. This unit is designed to operate within a negative pressure range of 0.15-0.17 inches of water column (37-42 Pa).
Troubleshooting DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. ● Do not remove from the firebox any screws without penetrating oil lubrication. WHAT TO DO IF: 1. The stove will not start. 2. The stove will not operate when hot. 3. The exhaust blower will not function normally. 4. Light # 3 on Heat output bar flashing. 5.
Troubleshooting • • Exhaust Temperature Sensor failure. Bypass sensor located on Exhaust Blower, if stove now operates properly, the unit may require cleaning or a new sensor. Contact your local dealer for service. Check the agitator to make sure it is turning properly 3. The exhaust motor will not function normally. • Check the line fuse to see if it has blown. • Open the access panels; check all connections against the wiring diagram.
Troubleshooting 7. The convection blower will not function normally. • Check the line fuse to see if it has blown. • Clean all grill openings at the back and below unit . • Check the Voltage across the blower wires, It should adjust with the heat output settings. If not contact your local dealer for service. 8. Ignitor - the pellets will not light. • Check the line fuse to see if it has blown. NOTE: The ignitor should be bright orange in color.
Wiring Diagram Red Combustion Blower Black Black Blue 2µF Capacitor Brown Exhaust Temperature Sensor Brown Blue Blue Black White Red White 120V Ground Plug Air Pump Green Ground Red White 5 Amp Green White Ground Black 2 Amp 2 Amp 2 Amp 2 Amp Thermostat Ignitor Agitator Motor Blue/Yellow Black Red Yellow Purple Blue Brown Brown White Connect Thermostat Here White White Yellow Auger Motor 6 µF Capacitor Purple White Grey Grey Grey Grey Orange Orange Orange Orange Brown
Parts List Reference # Part # OPTION Log Set 50-1963 OPTION M55CI O/S Filler Panel 50-2155 OPTION Pellet Stove Thermostat 50-1971 OPTION Glass Tinted M55C 50-2247 OPTION M55C-FPI Service Rails 50-2262 Hopper Switch 50-2052 1 24 Description 2 High Limit Temp Sensor 200°F (93°C) Manual Reset EF-016 3 120°F (49°C) Ceramic Fan Temp Sensor EC-001 4 ⅝” I.D.
Parts List Reference # Description Part # 37 M55C-FPI Control Panel with Decal 50-2267 38 Exhaust Channel CW Sensor 50-2286 39 Baffle 50-2287 40 ¼” Spring Pin 50-1701 41 Agitator Bushing Left Side 50-1703 42 M55C-FS Wiring Harness 50-2149 43 Latch Bolt & Rollers C/W Nut 50-2213 44 Motherboard Mounting Panel 50-2288 45 Burn Pot Scraper Tool 50-1254 46 Door And Ash Door Gasket 9/16 Firm - 10ft (3.
Parts List Reference # 26 Description Part # 67 M55C-FPI Cast Side Right - PD 50-2270 67 M55C-FPI Cast Side Right - Beach 50-2275 67 M55C-FPI Cast Side Right - Chestnut 50-2281 67 M55C-FPI Cast Side Right - DB 50-2298 68 M55C-FPI Cast Ash Door - PD 50-2271 68 M55C-FPI Cast Ash Door - Beach 50-2276 68 M55C-FPI Cast Ash Door - Chestnut 50-2282 68 M55C-FPI Cast Ash Door - DB 50-2299 69 M55C-FPI Cast Surround Trim Only - PD 50-2272 69 M55C-FPI Cast Surround Trim Only - Beach 50-
Parts Diagram - Components 6 8 23 48 4 3 19 20 37 13 14 29 2 1 10 15 52 11 42 47 9 21 49 7 41 18 54 45 17 16 22 5 24 12 53 25 40 27
Parts Diagram - Steel 70 69 30 28 38 39 63 5 62 37 36 61 44 51 59 57 66 26 65 27 67 68 28 64
Warranty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the finest materials and is backed by our Exclusive Lifetime Limited Warranty to the original purchaser. With Enviro, you’re not just buying a stove, you’re buying a company with years of unequalled performance and quality.
Warranty Exclusions and Limitations: 1. This Warranty does not cover tarnish, discoloration or wear on the plating or paint. 2. This Warranty excludes wear and tear or breakage caused by cleaning, moving or service on log set. 3. A qualified installer must install this stove or fireplace. This Limited Warranty covers defects in materials and workmanship only if the product has been installed in accordance with local building and fire codes; in their absence, refer to the owner’s manual.
Warranty 17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warranty. 18. The Limited Warranty does not cover tarnish, discoloration or wear on the plated surfaces. 19. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint during normal usage. It is not a flaw and is not covered under warranty. 20.
Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference.
